Kinlochleven Hydroelectric Scheme | |
---|---|
Country | Scotland, UK |
Location | Kinlochleven, Highland |
Coordinates | 56°42′46″N4°57′29″W / 56.71278°N 4.95806°W |
Status | Operational |
Construction began | 1904 |
Commission date | 1907–1909 (refurbished 1996-2000) |
Power generation | |
Units operational | 3 × 10 MW |
Make and model | Gilkes Francis turbines |
Units decommissioned | 11 × 2 MW (DC) Escher Wyss (Zürich) Pelton |
The Kinlochleven hydroelectric scheme was built between 1905 and 1909 to supply power for an Aluminium smelter owned by British Aluminium. It was the second in Scotland after the 1896 Falls of Foyers scheme. The smelter and power house were constructed on the south bank of the River Leven in the village of Kinlochleven, in the south-west of the Scottish Highlands.
The Blackwater Reservoir was formed by constructing a mass concrete gravity dam over ½ mile (800 m) across the Blackwater, the main tributary of the River Leven, with a catchment area of 60 square miles (160 km2). Water is conveyed along a covered concrete conduit 3.5 miles (5.6 km) long, which also collects water from three side stream intakes. The water descends 935 feet (285 m) from the valve house to the power house via six steel pipes.
Power was originally generated by 11 Pelton wheel turbines and three auxiliary sets, with a total capacity of 25,725 kW. These were replaced between 1996 and 2001 by Gilkes, who installed three 10 MW Francis turbines. [1]
The aluminium smelter closed in 2000, [2] but the power station continues to export power via the National Grid to the Lochaber smelter in Fort William, via an upgraded 132 kV overhead line.
The scheme was consented by the Loch Leven Water Power Acts of 1901 and 1904, the latter of which extended the time available for completion and had some variations in the scheme. The scheme was designed by Thomas Meik and Sons, with consulting input from Sir A R Binnie.
Construction of the hydroelectric scheme started in 1905, and took approximately four years. The main contractor was Sir John Jackson Ltd, with A H Roberts as the resident engineer. Construction cost about £600,000, or around £60m adjusted for inflation to 2024. [3]
The workforce was largely Irish Navvies, with around 3,000 men working in squalid conditions. Many died in construction accidents, and were buried in a graveyard beside the dam, with concrete headstones. [4]
Materials were transferred to the Blackwater Dam construction site by means of an aerial cableway from a wharf on Loch Leven. This was supported on trestles 10–130 ft (3–40 m) high with spans of 100–1,000 ft (30–305 m), and powered by a temporary hydroelectric plant with a 250 horsepower (190 kW) Pelton wheel. A railway was also constructed between the wharf and the dam. This had two rope inclines of 200 and 600 feet (61 and 183 m), but otherwise generally followed the contours of the valley.
The Blackwater Dam was 3,112 feet (949 m) long and 86 feet (26 m) high. It was constructed just upstream of Dubh Lochan, and inundated Lochan Inbhir, Lochan na Sàlach Uidre and Loch a'Bhàillidh. [5] During construction, it was found the unit weight of concrete made with local aggregate was lower than used in design calculations, so the profile of the dam was amended to give it a wider base, with an overturning factor of safety of 2.28.
From the dam, water is conveyed along a reinforced concrete conduit, 8 feet (2.4 m) square and 3.5 miles (5.6 km) long, with a fall of 1 in 1000. After passing through the valve house, the water descends through six parallel high-pressure penstocks made of steel, each 39 inches (0.99 m) in diameter and 5,750 feet (1,750 m) long.
During World War I, due to increasing demands for aluminium, Balfour Beatty was commissioned to construct a dam and aqueduct to bring additional water for the scheme from Loch Eilde Mòr, increasing the catchment to around 66 square miles (170 km2). This was constructed by 1,200 German prisoners of war and 500 British troops "of low medical category".
A temporary smelter was constructed and commenced production in 1907, although this closed after the main works opened in 1909.
The power house originally had 11 Pelton turbines made by Escher Wyss (Zürich). Each turbine was coupled to two 1,000 kW DC generators made by Dick, Kerr & Co., which powered the smelting process. There were also two AC generators for auxiliary power. [6]
The annual output of the hydroelectric scheme reached 160 GWh, a load factor of over 80%.
In 1994, closure of the smelter was by around the end of the century was announced by the owners at that time Alcan Smelting and Power UK Ltd. It eventually closed in June 2000. The power house building was Grade A listed on 3 August 2004.
Gilkes installed three 10 MW horizontal-axis Francis turbines between 1996 and 2001, in stages while the facility was operating. The first turbine (K1) was installed in 1996, and was controlled by a simple PLC to maintain grid frequency. The other turbines (K2 & K3) were installed in 1999 and 2000. The full system was controlled by a Gilkes digital speed governor, which allows the scheme to operate in an 'island' mode if the grid fails. Flow to each of the three turbines comes from two of the six penstocks, with a new Y-piece and downstream lateral compensator. Each turbine has a peak flow of 4.15 m³/s. [7] [8]
In April 2002, Kinlochleven the "Declared Net Capacity" (DNC) was downrated to 19.5 MW from the previous 30 MW, [9] permitting accreditation under the Renewables Obligation (RO) support mechanism which only applied to hydropower schemes with a DNC under 20 MW. The DNC is the maximum continuous power output of the plant, excluding that used by the facility. [9]
The rules of the RO (Scotland) were changed in 2018, allowing the capacity of the hydropower station to be upgraded back to 27.5 MW, although it only gets RO support for 19.5 MW, the 8 MW increase receives no subsidy. [10] The upgrade was completed by April 2020, and in the week before 21 April the scheme generated an average of 23.27 MW (approximately 3.9 GWh total). [11]
With the Kinlochleven scheme downrated, plans were drawn up to directly harness the water from Loch Eilde Mòr. A 5 MW scheme was approved by the Scottish Government in July 2011. [12]
In 2017, a smaller 2 MW scheme was commissioned. This involved modifications to the original dam and intake, approximately 3 km of new pipework, and a powerhouse on the north bank of the River Leven, with a three-jet horizontal Pelton wheel turbine. [13] The scheme cost around £13.6 million to construct, and will contribute an annual community benefit of £5000/MW. [14]
Planning permission was granted to Green Highland Renewables in March 2019, amended a year later, to construct an 800 kW scheme at the base of the Blackwater Dam. This uses the hydraulic head of the dam to generate additional power. Construction of the scheme was between January and November 2021. [15] [16] [17]
Water is diverted from one of the three cast-iron pipes 42 inches (1.1 m) in diameter which pass through the base of the dam, through a new new turbine and returned to the original stilling pond. The water then flows through the concrete conduit to Kinlochleven.
In 1909 when the smelter was completed, the total annual output of all other smelters in Britain was about 2,500 tons, which was less than one third the designed output of the Kinlochleven smelter. The smelter produced about 8,000 tonnes per year, significantly less than modern plants which produce around 250,000, which meant it was less economical to run. [18]
Peak employment in the smelter was over 700 people, although by January 1999 there were just 96 employees. [18]
A narrow-gauge railway approximately a mile long linked the pier on the southern shore of Loch Leven and the smelter, which operated between 1906 and 1960. It was double track throughout with a gauge of 3 feet (0.91 m) and overhead electric power at 500–550 V DC, making it the first electric railway in Scotland. Four-wheeled electric locomotives were built in Preston, Lancashire by Dick, Kerr & Co. (who also made the generators for the hydroelectric scheme) to haul freight only. [19] [20] [21]
Kinlochleven is a coastal village located in Lochaber, in the Scottish Highlands and lies at the eastern end of Loch Leven. To the north lie the Mamores ridge; to the south lie the mountains flanking Glen Coe.
The Blackwater Reservoir is a reservoir created behind a dam in the mountains above Kinlochleven, Lochaber, Highland, Scotland. The dam is 914 metres (2,999 ft) long, the longest in the Highlands.
Hydroelectricity, or hydroelectric power, is electricity generated from hydropower. Hydropower supplies one sixth of the world's electricity, almost 4,500 TWh in 2020, which is more than all other renewable sources combined and also more than nuclear power. Hydropower can provide large amounts of low-carbon electricity on demand, making it a key element for creating secure and clean electricity supply systems. A hydroelectric power station that has a dam and reservoir is a flexible source, since the amount of electricity produced can be increased or decreased in seconds or minutes in response to varying electricity demand. Once a hydroelectric complex is constructed, it produces no direct waste, and almost always emits considerably less greenhouse gas than fossil fuel-powered energy plants. However, when constructed in lowland rainforest areas, where part of the forest is inundated, substantial amounts of greenhouse gases may be emitted.
The Falls of Foyers are two waterfalls on the River Foyers, which feeds Loch Ness, in Highland, Scotland. They are located on the lower portion of the River Foyers, and consist of the upper falls, with a drop of 46 feet (14 m) and the lower falls, which drop 98 feet (30 m).
The Rubicon Hydroelectric Scheme is a small run-of-the-river hydroelectric scheme located on the Rubicon and Royston Rivers, north east of Melbourne, 40 km (25 mi) south-west of Alexandra, Victoria, Australia. The scheme commenced in 1922, and was the first state-owned hydroelectric scheme to generate electricity in mainland Australia, and among the first in the world to be remotely controlled. For the first ten years of its operation it supplied on average 16.9% of electricity generated by the State Electricity Commission of Victoria. It is now owned and operated by AGL Energy and contributes approximately 0.02% of Victoria's energy supply.
Laggan Dam is a mass concrete gravity dam located on the River Spean south west of Loch Laggan in the Scottish Highlands. It forms the second reservoir for the Lochaber hydroelectric scheme.
The Affric-Beauly hydro-electric power scheme for the generation of hydro-electric power is located in the western Highlands of Scotland. It is based around Glen Strathfarrar, Glen Cannich and Glen Affric, and Strathglass further downstream.
The Glendoe Hydro Scheme for the generation of hydro-electric power is located in the Monadhliath Mountains near Fort Augustus, above Loch Ness in the Highlands of Scotland. The change in financial incentives following the publication of the Renewables Obligation in 2001 caused Scottish and Southern Energy (SSE) to reconsider a number of schemes that had been mothballed in the 1960s by the North of Scotland Hydro-Electric Board, and plans for the Glendoe scheme were resurrected.
Nostie is a small remote hamlet, lying on Nostie Bay, an inlet at the northeastern end of the sea loch, Loch Alsh in the Scottish Highlands and is in the council area of Highland. Nostie lies a short distance from one of Scotland's popular tourist attractions, Eilean Donan Castle.
The Boguchany Dam is a large hydroelectric dam on the Angara River in Kodinsk, Krasnoyarsk Krai, Russia. It has an installed capacity of 2,997 MW. Construction of the power plant was completed when a ninth and final generator was brought online in January 2015.
The Cruachan Power Station is a pumped-storage hydroelectric power station in Argyll and Bute, Scotland, UK. The scheme can provide 440 MW of power and produced 705 GWh in 2009.
The Lochaber hydroelectric scheme is a hydroelectric power generation project constructed in the Lochaber area of the western Scottish Highlands after the First World War. Like its predecessors at Kinlochleven and Foyers, it was designed to provide electricity for aluminium production, this time at Fort William.
The Afulilo Dam is a gravity dam on the Afulilo River about 3 km (1.9 mi) south of Ta'elefaga in the district of Va'a-o-Fonoti on Upolu island of Samoa. The primary purpose of the dam is hydroelectric power generation and it supports a 4 megawatts (5,400 hp) power station. It is the largest hydroelectric power station by installed capacity in Samoa. First studied in 1980, construction on the project began in 1990 and the power station was commissioned in 1993. Funding for the US$26.6 million project was provided by the World Bank, Asian Development Bank, International Development Association, European Investment Bank, and European Economic Community loans and grants.
The Breadalbane Hydro-Electric Scheme is a hydroelectric scheme in the Breadalbane area of Perthshire, Scotland. It comprises seven power stations which generate 120MW of power from the dams around Loch Lyon, Loch Earn and Loch Tay.
The Tapovan Vishnugad Hydropower Plant is a 520 MW run-of-river hydroelectric project being constructed on Dhauliganga River in Chamoli District of Uttarakhand, India. The plant is expected to generate over 2.5 TWh of electricity annually.
Nenskra Hydro Power Plant is a proposed hydroelectric power station to be located on the southern slopes of the Central Caucasus mountains in Svaneti, Georgia.
Dolgarrog Power Station in Dolgarrog, Wales was originally built in 1907 as part of an aluminium smelting plant. It uses water turbines to drive electricity alternators. Public supplies began in 1922 when power lines were constructed to transmit electricity from the power station to Colwyn Bay, Conwy and Llandudno. The station was vested in the British Electricity Authority and its successors following nationalisation in 1948. It is currently (2021) operated by RWE NPower UK.
Storr Lochs is a hydro-electric power station built on the Isle of Skye, Inner Hebrides, Scotland and commissioned in 1952. It was built by the North of Scotland Hydro-Electric Board, and used water from Lochs Leathan and Fada, to provide the first general supply of electricity to the island. Because the location of the turbine house was not easily accessible, it is served by an electric funicular railway.
Lussa Hydro-Electric Scheme is a small-scale hydro-electric power station, built by the North of Scotland Hydro-Electric Board and commissioned in 1956. It is located near Peninver on the Kintyre peninsula, part of Argyll and Bute in Scotland. It was originally designed to supply power to Campbeltown, but is now connected to the National Grid.