Each of the eight 32-bit cores (termed a cog) has a central processing unit (CPU) which has access to 512 32-bit long words (2KB) of instructions and data. Self-modifying code is possible and is used internally, for example, as the boot loader overwrites itself with the Spin Interpreter. Subroutines in Spin (object-based high-level code) use a call-return mechanism requiring use of a call stack. Assembly (PASM, low-level) code needs no call stack. Access to shared memory (32KB random-access memory (RAM); 32KB read-only memory (ROM)) is controlled via round-robin scheduling by an internal computer bus controller termed the hub. Each cog also has access to two dedicated hardware counters and a special video generator for use in generating timing signals for PAL, NTSC, VGA, servomechanism-control, and others.[4]
Speed and power management
The Propeller can be clocked using either an internal, on-chip oscillator (providing a lower total part count, but sacrificing some accuracy and thermal stability) or an external crystal oscillator or ceramic resonator (providing higher maximum speed with greater accuracy at higher total cost). Only the external oscillator may be run through an on-chip phase-locked loop (PLL) clock multiplier, which may be set at 1x, 2x, 4x, 8x, or 16x.
Both the on-board oscillator frequency (if used) and the PLL multiplier value may be changed at run-time. If used correctly, this can improve power efficiency; for example, the PLL multiplier can be decreased before a long no operation wait needed for timing purposes, then increased afterward, causing the processor to use less power. However, the utility of this technique is limited to situations where no other cog is executing timing-dependent code (or is carefully designed to cope with the change), since the effective clock rate is common to all cogs.
The effective clock rate ranges from 32kHz up to 80MHz (with the exact values available for dynamic control dependent on the configuration used, as described above). When running at 80MHz, the proprietary interpreted Spin programming language executes approximately 80,000 instruction-tokens per second on each core, giving 8 times 80,000 for 640,000 high-level instructions per second. Most machine-language instructions take 4 clock-cycles to execute, resulting in 20 million instructions per second (MIPS) per cog, or 160MIPS total for an 8-cog Propeller.
Power use can be reduced by lowering the clock rate to what is needed, by turning off unneeded cogs (which then use little power), and by reconfiguring I/O pins which are unneeded, or can be safely placed in a high-impedance state (tristated), as inputs. Pins can be reconfigured dynamically, but again, the change applies to all cogs, so synchronizing is important for certain designs. Some protection is available for situations where one core attempts to use a pin as an output while another attempts to use it as an input; this is explained in Parallax's technical reference manual.
On-board peripherals
Each cog has access to some dedicated counter-timer hardware, and a special timing signal generator intended to simplify the design of video output stages, such as composite PAL or NTSC displays (including modulation for broadcast) and Video Graphics Array (VGA) monitors. Parallax thus makes sample code available which can generate video signals (text and somewhat low-resolution graphics) using a minimum parts count consisting of the Propeller, a crystal oscillator, and a few resistors to form a crude digital-to-analog converter (DAC). The frequency of the oscillator is important, as the correction ability of the video timing hardware is limited to the clock rate. It is possible to use multiple cogs in parallel to generate a single video signal. More generally, the timing hardware can be used to implement various pulse-width modulation (PWM) timing signals.
ROM extensions
In addition to the Spin interpreter and a boot loader, the built-in ROM provides some data which may be useful for certain sound, video, or mathematics applications:
a bitmap font is provided, suitable for typical character generation applications (but not customizable);
a sine table (16-bit, 2049 entries representing first quadrant, angles from 0 to π/2; other three quadrants are created from the same table).
The math extensions are intended to help compensate for the lack of a floating-point unit, and more primitive missing operations, such as multiplication and division (this is masked in Spin but is a limit for assembly language routines). The Propeller is a 32-bit processor, however, and these tables may have insufficient accuracy for higher-precision uses.
Spin code is written on the Propeller Tool, a GUI-oriented software development platform written for Windows XP.[6] This compiler converts the Spin code into bytecodes that can be loaded (with the same tool) into the main 32KB RAM, and optionally into the I²C boot electrically erasable programmable read-only memory (EEPROM), of the Propeller chip. After booting the propeller, a bytecode interpreter is copied from the built in ROM into the 2KB RAM of the primary COG. This COG will then start interpreting the bytecodes in the main 32KB RAM. More than one copy of the bytecode interpreter can run in other COGs, so several Spin code threads can run simultaneously. Within a Spin code program, assembly code program(s) can be inline inserted. These assembler program(s) will then run on their own COGs.
The Propeller's interpreter for its proprietary multi-threaded Spin computer language is a bytecode interpreter. This interpreter decodes strings of instructions, one instruction per byte, from user code which has been edited, compiled, and loaded onto the Propeller from within a purpose-specific integrated development environment (IDE). This IDE, which Parallax names The Propeller tool, is intended for use under a Microsoft Windows operating system.
The Spin language is a high-level programming language. Because it is interpreted in software, it runs slower than pure Propeller assembly, but can be more space-efficient: Propeller assembly opcodes are 32 bits long; Spin directives are 8 bits long, which may be followed by a number of 8-bit bytes to specify how that directive operates. Spin also allows avoiding significant memory segmentation issues that must be considered for assembly code.
At startup, a copy of the bytecode interpreter (less than 2KB in size), will be copied into the dedicated RAM of a cog and will then start interpreting bytecode in the main 32KB RAM. Additional cogs can be started from that point, loading a separate copy of the interpreter into the new cog's dedicated RAM (a total of eight interpreter threads can, thus, run simultaneously). Notably, this means that at least a minimal amount of startup code must be Spin code, for all Propeller applications.
Syntax
Spin's syntax can be divided into blocks, which hold:
VAR – global variables
CON – program constants
PUB – code for a public subroutine
PRI – code for a private subroutine
OBJ – code for objects
DAT – predefined data, memory reservations and assembly code
Example keywords
reboot: causes the microcontroller to reboot
waitcnt: wait for the system counter to equal or exceed a specified value
waitvid: waits for a (video) timing event before outputting (video) data to I/O pins
coginit: starts a processor on a new task
Example program
An example program, (as it would appear in the Propeller Tool editor) which emits the current system counter every 3,000,000 cycles, then is shut down by another cog after 40,000,000 cycles:
The Parallax Propeller is gradually accumulating software libraries which give it similar abilities to Parallax's older BASIC Stamp product; however there is no uniform list of which PBASIC facilities now have Spin equivalents.
It has been jokingly opined that "If two languages were to meet in a bar – Fortran and BASIC – nine months later one would find Spin." This refers to the whitespace formatting of FORTRAN and the keyword-based operation of BASIC.
Package and I/O
The initial version of the chip (called the P8X32A) provides one 32-bit port in a 40-pin 0.6in dual in-line package (DIP), 44-pin LQFP, or Quad Flat No-leads package (QFN) surface-mount technology package. Of the 40 available pins, 32 are used for I/O, four for power and ground pins, two for an external crystal (if used), one to enable power outage and brownout detection, and one for reset.
All eight cores can access the 32-bit port (designated "A"; there is currently no "B") simultaneously. A special control mechanism is used to avoid I/O conflicts if one core attempts to use an I/O pin as an output while another tries to use it as input. Any of these pins can be used for the timing or pulse-width modulation output techniques described above.
Parallax has stated that it expects later versions of the Propeller to offer more I/O pins and/or more memory.[7]
Virtual I/O devices
Screen capture of the graphics demo that Parallax created to demonstrate the NTSC video library
The Propeller's designers designed it around the concept of "virtual I/O devices". For example, the HYDRA Game Development Kit, (a computer system designed for hobbyists, to learn to develop retro-style video games) uses the built-in character generator and video support logic to generate a virtualgraphics processing unit-generator that outputs VGA color pictures, PAL/NTSC compatible color pictures or broadcast RF video+audio in software.[8]
The screen capture displayed here was made using a software virtual display driver that sends the pixel data over a serial link to a PC.[9]
Software libraries are available to implement several I/O devices ranging from simple UARTs and Serial I/O interfaces such as SPI, I²C and PS/2 compatible serial mouse and keyboard interfaces, motor drivers for robotic systems, MIDI interfaces and LCD controllers.[10]
Dedicated cores instead of interrupts
The design philosophy of the Propeller is that a hard real-time multi-core architecture negates the need for dedicated interrupt hardware and support in assembly. In traditional CPU architecture, external interrupt lines are fed to an on-chip interrupt controller and are serviced by one or more interrupt service routines. When an interrupt occurs, the interrupt controller suspends normal CPU processing and saves internal state (typically on the stack), then vectors to the designated interrupt service routine. After handling the interrupt, the service routine executes a return from interrupt instruction which restores the internal state and resumes CPU processing.
To handle an external signal promptly on the Propeller, any one of the 32 I/O lines is configured as an input. A cog is then configured to wait for a transition (either positive or negative edge) on that input using one of the two counter circuits available to each cog. While waiting for the signal, the cog operates in low-power mode, essentially sleeping. Extending this technique, a Propeller can be set up to respond to eight independent interrupt lines with essentially zero handling delay. Alternately, one line can be used to signal the interrupt, and then additional input lines can be read to determine the nature of the event. The code running in the other cores is not affected by the interrupt handling cog. Unlike a traditional multitasking single-processor interrupt architecture, the signal response timing remains predictable,[11] and indeed using the term interrupt in this context can cause confusion, since this function can be more properly thought of as polling with a zero loop time.
Boot mechanism
On power up, Brownout detection, software reset, or external hardware reset, the Propeller will load a machine-code booting routine from the internal ROM into the RAM of its first (primary) cog and execute it. This code emulates an I²C interface in software, temporarily using two I/O pins for the needed serial clock and data signals to load user code from an external I2C EEPROM.
Simultaneously, it emulates a serial port, using two other I/O pins that can be used to upload software directly to RAM (and optionally to the external EEPROM). If the Propeller sees no commands from the serial port, it loads the user program (the entry code of which must be written in Spin, as described above) from the serial EEPROM into the main 32KB RAM. After that, it loads the Spin interpreter from its built-in ROM into the dedicated RAM of its first cog, overwriting most of the bootloader.
Regardless of how the user program is loaded, execution starts by interpreting initial user bytecode with the Spin interpreter running in the primary cog. After this initial Spin code runs, the application can turn on any unused cog to start a new thread, and/or start assembly language routines.
External persistent memory
The Propeller boots from an external serial EEPROM; once the boot sequence completes, this device may be accessed as an external peripheral.[12]
Other language implementations
Apart from Spin and the Propeller's low-level assembler, a number of other languages have been ported to it.
C compiler
Parallax supports Propeller-GCC which is a port of the GNU Compiler Collection (GCC) compiler for the programming languages C and C++, for Propeller[13] (branch release_1_0). The C compiler and the C Library are ANSI C compliant. The C++ compiler is ANSI-C99 compliant. Full C++ is supported with external memory. The SimpleIDE program[14] provides users a simple way to write programs without requiring makefiles. In 2013, Parallax incorporated Propeller-GCC and Simple Libraries into the Propeller-C Learn series of tutorials.[15] Propeller-GCC is actively maintained. Propeller-GCC and SimpleIDE are officially supported Parallax software products.
The ImageCraft ICCV7 for Propeller C compiler has been marked to end-of-life state.[16]
A free ANSI C compiler named Catalina is available.[17] It is based on LCC. Catalina is actively maintained.
BASIC compiler
PropBASIC is a BASIC programming language for the Parallax Propeller Microcontroller.[18] PropBASIC requires Brad's Spin Tool (BST), a cross-platform set of tools for developing with the Parallax Propeller. As of August 2015, BST runs on i386-linux-gtk2, PowerPC-darwin (Mac OS X 10.4 through 10.6), i386-darwin (Mac OS X 10.4 through 10.6) and i386-Win32 (Windows 95 through Windows 7).
A free version that enjoys extensive development and community support is PropForth.[19] It is tailored to the prop architecture, and necessarily deviates from any general standard regarding architectural uniqueness, consistent with the concept of Forth.
Beyond the Forth interpreter, PropForth provides many features that exploit the chip's abilities. Linked I/O refers to the method of associating a stream with process, allowing one process to link to the next on the fly, transparent to the application. This can reduce or eliminate the need of a hardware debugging or JTAG interface in many cases. Multi-Channel Synchronous Serial (MCS) refers to the synchronous serial communication between prop chips. 96-bit packets are sent continuously between two cogs, the result is that applications see additional resources (+6 cogs for each prop chip added) with little or no impact on throughput for a well constructed application.
LogicAnalyzer refers to an extension package that implements software logic analyzer. EEPROMfilesystem and SDfilesystem are extensions that implement rudimentary storage using EEPROM and SD flash.
PagedAssembler refers to the package of optimizations that allow assembler routines to be swapped in (and out by overwrite) on the fly, allowing virtually unlimited application size. Script execution allows extensions to be loaded on the fly, allowing program source up to the size of storage media.
Propeller and Java
There are efforts underway to run the Java virtual machine (JVM) on Propeller. A compiler, debugger, and emulator are being developed.[20]
Pascal compiler and runtime
A large subset of Pascal is implemented by a compiler and interpreter based on the p-code machine P4 system.[21]
Graphical programming
Screen capture of the PICoPLC ladder editor
PICo programmable logic controller (PLC, PICoPLC) supports output to Propeller processor. The program is created in a GUI ladder logic editor and resulting code is emitted as Spin source. PICoPLC also supports P8X32 with create-simulate-run feature. No restrictions on target hardware as the oscillator frequency and IO pins are freely configurable in the ladder editor. PICoPLC developer website ().
Future versions
As of 2014[update], Parallax is building a new Propeller[22] with cogs that each will run at about 200MIPS, whereas the current Propeller's cogs each run at around 20MIPS. The improved performance would result from a maximum clock speed increase to 200MHz (from 80MHz) and an architecture that pipelines instructions, executing an average of nearly one instruction per clock cycle (approximately a ten-fold increase).[7]
Related Research Articles
A microcontroller or microcontroller unit (MCU) is a small computer on a single integrated circuit. A microcontroller contains one or more CPUs along with memory and programmable input/output peripherals. Program memory in the form of NOR flash, OTP ROM, or ferroelectric RAM is also often included on the chip, as well as a small amount of RAM. Microcontrollers are designed for embedded applications, in contrast to the microprocessors used in personal computers or other general-purpose applications consisting of various discrete chips.
The Intel MCS-51 is a single chip microcontroller (MCU) series developed by Intel in 1980 for use in embedded systems. The architect of the Intel MCS-51 instruction set was John H. Wharton. Intel's original versions were popular in the 1980s and early 1990s, and enhanced binary compatible derivatives remain popular today. It is a complex instruction set computer, but also has some of the features of RISC architectures, such as a large register set and register windows, and has separate memory spaces for program instructions and data.
Bytecode is a form of instruction set designed for efficient execution by a software interpreter. Unlike human-readable source code, bytecodes are compact numeric codes, constants, and references that encode the result of compiler parsing and performing semantic analysis of things like type, scope, and nesting depths of program objects.
AVR is a family of microcontrollers developed since 1996 by Atmel, acquired by Microchip Technology in 2016. These are modified Harvard architecture 8-bit RISC single-chip microcontrollers. AVR was one of the first microcontroller families to use on-chip flash memory for program storage, as opposed to one-time programmable ROM, EPROM, or EEPROM used by other microcontrollers at the time.
PIC is a family of microcontrollers made by Microchip Technology, derived from the PIC1640 originally developed by General Instrument's Microelectronics Division. The name PIC initially referred to Peripheral Interface Controller, and is currently expanded as Programmable Intelligent Computer. The first parts of the family were available in 1976; by 2013 the company had shipped more than twelve billion individual parts, used in a wide variety of embedded systems.
The MSP430 is a mixed-signal microcontroller family from Texas Instruments, first introduced on 14 February 1992. Built around a 16-bit CPU, the MSP430 was designed for low power consumption embedded applications and low cost.
The PIC16C84, PIC16F84 and PIC16F84A are 8-bit microcontrollers of which the PIC16C84 was the first introduced in 1993 and hailed as the first PIC microcontroller to feature a serial programming algorithm and EEPROM memory. It is a member of the PIC family of controllers, produced by Microchip Technology. The memory architecture makes use of bank switching. Software tools for assembler, debug and programming were only available for the Microsoft DOS and Windows operating systems.
Embedded software is computer software, written to control machines or devices that are not typically thought of as computers, commonly known as embedded systems. It is typically specialized for the particular hardware that it runs on and has time and memory constraints. This term is sometimes used interchangeably with firmware.
The BASIC Stamp is a microcontroller with a small, specialized BASIC interpreter (PBASIC) built into ROM. It is made by Parallax, Inc. and has been popular with electronics hobbyists since the early 1990s.
The 68HC12 is a microcontroller family from Motorola Semiconductor. Originally introduced in the mid-1990s, the architecture is an enhancement of the Freescale 68HC11. Programs written for the HC11 are usually compatible with the HC12, which has a few extra instructions. The first 68HC12 derivatives had a maximum bus speed of 8 MHz and flash memory sizes up to 128 KB.
PICAXE is a microcontroller system based on a range of Microchip PIC microcontrollers. PICAXE devices are Microchip PIC devices with pre-programmed firmware that enables bootloading of code directly from a PC, simplifying hobbyist embedded development. PICAXE devices have been produced by Revolution Education (Rev-Ed) since 1999.
The XGameStation is a series of embedded systems, primarily designed as a dedicated home video game console, created by Andre LaMothe and sold by his company Nurve Networks LLC. Originally designed to teach electronics and video game development to programmers, newer models concentrate more on logic design, multi-core programming, game programming, and embedded system design and programming with popular microcontrollers.
Parallax Inc. is a privately held company in Rocklin, California. Parallax Inc. designs, manufactures, and sells BASIC Stamp microcontrollers, Propeller microcontrollers, microcontroller accessories, educational robot kits, and educational curriculum.
The HYDRA Game Development Kit launched in September 2006, and was developed by André LaMothe who designed the prior XGameStation series of consoles. Like the XGameStation, HYDRA is an open system, allowing anyone to create games for it. However, while still designed to teach electronics and programming, the system places greater focus on homebrew games. Compared to the prior XGameStation consoles, the HYDRA uses a more complex and powerful CPU - the then recently released Parallax Propeller processing unit, which has eight 32 bit RISC CPUs called cogs with 32 KB built in RAM and 32 KB built in ROM.
Parallax SX is a discontinued line of microcontrollers that was marketed by Parallax, from a design by Ubicom. Designed to be architecturally similar to the PIC microcontrollers used in the original versions of the BASIC Stamp, SX microcontrollers replaced the PIC in several subsequent versions of that product.
A single-board microcontroller is a microcontroller built onto a single printed circuit board. This board provides all of the circuitry necessary for a useful control task: a microprocessor, I/O circuits, a clock generator, RAM, stored program memory and any necessary support ICs. The intention is that the board is immediately useful to an application developer, without requiring them to spend time and effort to develop controller hardware.
STM32 is a family of 32-bit microcontroller integrated circuits by STMicroelectronics. The STM32 chips are grouped into related series that are based around the same 32-bit ARM processor core: Cortex-M0, Cortex-M0+, Cortex-M3, Cortex-M4, Cortex-M7, Cortex-M33. Internally, each microcontroller consists of ARM processor core(s), flash memory, static RAM, debugging interface, and various peripherals.
The Arduino Uno is an open-source microcontroller board based on the Microchip ATmega328P microcontroller (MCU) and developed by Arduino.cc and initially released in 2010. The microcontroller board is equipped with sets of digital and analog input/output (I/O) pins that may be interfaced to various expansion boards (shields) and other circuits. The board has 14 digital I/O pins, 6 analog I/O pins, and is programmable with the Arduino IDE, via a type B USB cable. It can be powered by a USB cable or a barrel connector that accepts voltages between 7 and 20 volts, such as a rectangular 9-volt battery. It has the same microcontroller as the Arduino Nano board, and the same headers as the Leonardo board. The hardware reference design is distributed under a Creative Commons Attribution Share-Alike 2.5 license and is available on the Arduino website. Layout and production files for some versions of the hardware are also available.
The MSP432 is a mixed-signal microcontroller family from Texas Instruments. It is based on a 32-bit ARM Cortex-M4F CPU, and extends their 16-bit MSP430 line, with a larger address space for code and data, and faster integer and floating point calculation than the MSP430. Like the MSP430, it has a number of built-in peripheral devices, and is designed for low power requirements. In 2021, TI confirmed that the MSP432 has been discontinued and "there will be no new MSP432 products".
MicroPython is a software implementation of a programming language largely compatible with Python 3, written in C, that is optimized to run on a microcontroller.
↑ Gracey, Ken (2014). "Propeller 1 Open Source". Parallax Inc. Parallax Inc. Retrieved 23 January 2021. The Propeller 1 (P8X32A) is now a 100% open multicore microcontroller, including all of the hardware and tools ... The Propeller 1 may be the most open chip in its class.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
