Single-board microcontroller

Last updated January 11, 2024

A single-board microcontroller is a microcontroller built onto a single printed circuit board. This board provides all of the circuitry necessary for a useful control task: a microprocessor, I/O circuits, a clock generator, RAM, stored program memory and any necessary support ICs. The intention is that the board is immediately useful to an application developer, without requiring them to spend time and effort to develop controller hardware.

Origins

Single-board microcontrollers appeared in the late 1970s, when the appearance of early microprocessors, such as the 6502 and the Z80,^[1] made it practical to build an entire controller on a single board, as well as affordable to dedicate a computer to a relatively minor task.

In March 1976, Intel announced a single-board computer product that integrated all of the support components required for their 8080 microprocessor, along with 1 kilobyte of RAM, 4 kilobytes of user-programmable ROM, and 48 lines of parallel digital I/O with line drivers. The board also offered expansion through a bus connector, but could be used without an expansion card cage when applications did not require additional hardware. Software development for this system was hosted on Intel's Intellec MDS microcomputer development system; this provided assembler and PL/M support, and permitted in-circuit emulation for debugging.^[2]

Processors of this era required a number of support chips to be included outside of the processor. RAM and EPROM were separate, often requiring memory management or refresh circuitry for dynamic memory. I/O processing might have been carried out by a single chip such as the 8255, but frequently required several more chips.

A single-board microcontroller differs from a single-board computer in that it lacks the general-purpose user interface and mass storage interfaces that a more general-purpose computer would have. Compared to a microprocessor development board, a microcontroller board would emphasize digital and analog control interconnections to some controlled system, whereas a development board might by have only a few or no discrete or analog input/output devices. The development board exists to showcase or train on some particular processor family and, therefore, internal implementation is more important than external function.

Internal bus

The bus of the early single-board devices, such as the Z80 and 6502, was universally a Von Neumann architecture. Program and data memory were accessed via the same shared bus, even though they were stored in fundamentally different types of memory: ROM for programs and RAM for data. This bus architecture was needed to economise the number of pins needed from the limited 40 available for the processor's ubiquitous dual-in-line IC package.

It was common to offer access to the internal bus through an expansion connector, or at least provide space for a connector to be soldered on. This was a low-cost option and offered the potential for expansion, even if it was rarely used. Typical expansions would be I/O devices or additional memory. It was unusual to add peripheral devices such as tape or disk storage, or a CRT display

Later, when single-chip microcontrollers, such as the 8048, became available, the bus no longer needed to be exposed outside the package, as all necessary memory could be provided within the chip package. This generation of processors used a Harvard architecture with separate program and data buses, both internal to the chip. Many of these processors used a modified Harvard architecture, where some write access was possible to the program data space, thus permitting in-circuit programming. None of these processors required, or supported, a Harvard bus across a single-board microcontroller. When they supported a bus for expansion of peripherals, a dedicated I/O bus, such as I²C, 1-Wire or various serial buses, was used.

External bus expansion

Some microcontroller boards using a general-purpose microprocessor can bring the address and data bus of the processor to an expansion connector, allowing additional memory or peripherals to be added. This provides resources not already present on the single board system. Since not every system will require expansion, the connector may be optional, with a mounting position provided for installation by the user if desired.

Input and output

Microcontroller systems provide multiple forms of input and output signals to allow application software to control an external "real-world" system. Discrete digital I/O provides a single bit of data (on or off). Analog signals, representing a continuous variable range, such as temperature or pressure, can also be inputs and outputs for microcontrollers.

Discrete digital inputs and outputs might be buffered from the microprocessor data bus only by an addressable latch, or might be operated by a specialized input/output IC, such as an Intel 8255 or Motorola 6821 parallel input/output adapter. Later single-chip microcontrollers have input and output pins available. These input/output circuits usually do not provide enough current to directly operate devices like lamps or motors, so solid-state relays are operated by the microcontroller digital outputs, and inputs are isolated by signal conditioning level-shifting and protection circuits.

One or more analog inputs, with an analog multiplexer and common analog-to-digital converter, are found on some microcontroller boards. Analog outputs may use a digital-to-analog converter or, on some microcontrollers, may be controlled by pulse-width modulation. For discrete inputs, external circuits may be required to scale inputs, or to provide functions like bridge excitation or cold junction compensation.

To control component costs, many boards were designed with extra hardware interface circuits but without the components for these circuits installed, leaving the board bare. The circuit was added as an option on delivery, or could be populated later.

It is common practice for boards to include "prototyping areas", areas of the board laid out as a solderable breadboard area with the bus and power rails available, but without a defined circuit. Several controllers, particularly those intended for training, also include a pluggable, re-usable breadboard for easy prototyping of extra I/O circuits that could be changed or removed for later projects.

Communications and user interfaces

Communications interfaces vary depending on the age of the microcontroller system. Early systems might implement a serial port to provide RS-232 or current loop. The serial port could be used by the application program or could be used, in conjunction with a monitor ROM, to transfer programs into the microcontroller memory. Current microcontrollers may support USB, wireless networks (Wi-Fi, Zigbee, or others), or provide an Ethernet connection. In addition, they may support a TCP/IP protocol stack. Some devices have firmware available to implement a Web server, allowing an application developer to rapidly build a Web-enabled instrument or system.

Programming

Many early systems had no internal facilities for programming, and relied on a separate "host" system for this task. This programming was typically done in assembly language, or sometimes in C or PL/M, and then cross-assembled or cross-compiled on the host. Some single-board microcontrollers support a BASIC language system, allowing programs to be developed on the target hardware. Hosted development allows all the storage and peripherals of a desktop computer to be used, providing a more powerful development environment.

EPROM burning

Early microcontrollers relied on erasable programmable read-only memory (EPROM) devices to hold the application program. The object code from a host system would be "burned" onto an EPROM with an EPROM programmer.^[3] This EPROM was then physically plugged into the board. As the EPROM would be removed and replaced many times during program development, it was common to provide a ZIF socket to avoid wear or damage. Erasing an EPROM with a UV eraser takes a considerable time, and so it was also common for a developer to have several EPROMs in circulation at any one time.

Some microcontroller devices were available with on-board EPROM. These would also be programmed in a separate burner, then put into a socket on the target system.

The use of EPROM sockets allowed field updates to the application program, either to fix errors or to provide updated features.

Keypad monitors

When the single-board controller formed the entire development environment (typically in education), the board might also have included a simple hexadecimal keypad, calculator-style LED display, and a "monitor" program set permanently in ROM. This monitor allowed machine code programs to be entered directly through the keyboard and held in RAM. These programs were in machine code, not even in assembly language, and were often assembled by hand on paper before being inputted. It is arguable as to which process was more time-consuming and error prone: assembling by hand, or keying byte-by-byte.

Single-board "keypad and calculator display" microcontrollers of this type were very similar to some low-end microcomputers of the time, such as the KIM-1 or the Microprofessor I.^[4] Some of these microprocessor "trainer" systems are still in production today, used as very low-cost introductions to microprocessors at the hardware programming level.^[5]

Hosted development

When desktop personal computers appeared, initially CP/M or Apple II, then later the IBM PC and compatibles, there was a shift to hosted development. Hardware was now cheaper and RAM capacity had expanded such that it was possible to download the program through the serial port and hold it in RAM. This massive reduction in the cycle time to test a new version of a program gave an equally large boost in development speed.

This program memory was still volatile and would be lost if power was lost. Flash memory was not yet available at a viable price. As a completed controller project was usually required to be non-volatile, the final step in a project was often to burn it to an EPROM.

Single-chip microcontrollers

Single-chip microcontrollers, such as the Intel 8748, combined many of the features of previous boards into a single IC package. Single-chip microcontrollers integrate memory (both RAM and ROM) on-package and, therefore, do not need to expose the data and address bus through the pins of the IC package. These pins are then available for I/O lines. These changes also reduce the area required on the printed circuit board and simplify the design of the single-board microcontroller. Examples of single-chip microcontrollers include:

Intel 8748
PIC
Atmel AVR

Program memory

For production use as embedded systems, the on-board ROM was either mask programmed at the chip factory or one-time programmed (OTP) by the developer as a PROM. PROMs often used the same UV EPROM technology for the chip, but in a cheaper package without the transparent erasure window. During program development, it was still necessary to burn EPROMs. In this case, the entire controller IC, and therefore the ZIF sockets, would be provided.

With the development of affordable EEPROM and flash memory, it became practical to attach the controller permanently to the board and to download program code from a host computer through a serial connection. This was termed "in-circuit programming". Erasure of old programs was carried out by either over-writing them with a new download, or bulk erasing them electrically (for EEPROM). The latter method was slower, but could be carried out in-situ.

The main function of the controller board was then to carry the support circuits for this serial or, on later boards, USB interface. As a further convenience during development, many boards also had low-cost features like LED monitors of the I/O lines or reset switches mounted on board.

Single-board microcontrollers today

Dwengo board DwengoBoard.jpg — Dwengo board

It is now cheap and simple to design circuit boards for microcontrollers. Development host systems are also cheap, especially when using open source software. Higher level programming languages abstract details of the hardware, making differences between specific processors less obvious to the application programmer. Rewritable flash memory has replaced slow programming cycles, at least during program development. Accordingly, almost all development now is based on cross-compilation from personal computers and programs are downloaded to the controller board through a serial-like interface, usually appearing to the host as a USB device.

The original market demand for a simplified board implementation is no longer as relevant for microcontrollers. Single-board microcontrollers are still important, but have shifted their focus to:

Easily accessible platforms aimed at traditionally "non-programmer" groups, such as artists, designers, hobbyists, and others interested in creating interactive objects or environments.^[6] Some typical projects in 2011 included: the backup control of DMX stage lights and special effects, multi-camera control, autonomous fighting robots, controlling bluetooth projects from a computer or smart phone,^[7] LEDs and multiplexing, displays, audio, motors, mechanics, and power control.^[8] These controllers may be embedded to form part of a physical computing project. Popular choices for this work are the Arduino,^[9] Dwengo ^[7]^[10] or Wiring.^[11]^[12]
Technology demonstration boards for innovative processors or peripheral features:
- AVR Butterfly
- Parallax Propeller

Related Research Articles

<span class="mw-page-title-main">Motherboard</span> Main printed circuit board (PCB) for a computing device

A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.

The 68HC11 is an 8-bit microcontroller family introduced by Motorola Semiconductor in 1984. It descended from the Motorola 6800 microprocessor by way of the 6801. The 68HC11 devices are more powerful and more expensive than the 68HC08 microcontrollers and are used in automotive applications, barcode readers, hotel card key writers, amateur robotics, and various other embedded systems. The MC68HC11A8 was the first microcontroller to include CMOS EEPROM.

A microcontroller or microcontroller unit (MCU) is a small computer on a single integrated circuit. A microcontroller contains one or more CPUs along with memory and programmable input/output peripherals. Program memory in the form of ferroelectric RAM, NOR flash or OTP ROM is also often included on chip, as well as a small amount of RAM. Microcontrollers are designed for embedded applications, in contrast to the microprocessors used in personal computers or other general purpose applications consisting of various discrete chips.

An embedded system is a computer system—a combination of a computer processor, computer memory, and input/output peripheral devices—that has a dedicated function within a larger mechanical or electronic system. It is embedded as part of a complete device often including electrical or electronic hardware and mechanical parts. Because an embedded system typically controls physical operations of the machine that it is embedded within, it often has real-time computing constraints. Embedded systems control many devices in common use. In 2009, it was estimated that ninety-eight percent of all microprocessors manufactured were used in embedded systems.

The Intel MCS-51 is a single chip microcontroller (MCU) series developed by Intel in 1980 for use in embedded systems. The architect of the Intel MCS-51 instruction set was John H. Wharton. Intel's original versions were popular in the 1980s and early 1990s, and enhanced binary compatible derivatives remain popular today. It is a complex instruction set computer, but also has some of the features of RISC architectures, such as a large register set and register windows, and has separate memory spaces for program instructions and data.

The MCS-48 microcontroller series, Intel's first microcontroller, was originally released in 1976. Its first members were 8048, 8035 and 8748. The 8048 is arguably the most prominent member of the family. Initially, this family was produced using NMOS technology. In the early 1980s, it became available in CMOS technology. It was manufactured into the 1990s to support older designs that still used it.

The Intel 8085 ("eighty-eighty-five") is an 8-bit microprocessor produced by Intel and introduced in March 1976. It is software-binary compatible with the more-famous Intel 8080 with only two minor instructions added to support its added interrupt and serial input/output features. However, it requires less support circuitry, allowing simpler and less expensive microcomputer systems to be built. The "5" in the part number highlighted the fact that the 8085 uses a single +5-volt (V) power supply by using depletion-mode transistors, rather than requiring the +5 V, −5 V and +12 V supplies needed by the 8080. This capability matched that of the competing Z80, a popular 8080-derived CPU introduced the year before. These processors could be used in computers running the CP/M operating system.

AVR is a family of microcontrollers developed since 1996 by Atmel, acquired by Microchip Technology in 2016. These are modified Harvard architecture 8-bit RISC single-chip microcontrollers. AVR was one of the first microcontroller families to use on-chip flash memory for program storage, as opposed to one-time programmable ROM, EPROM, or EEPROM used by other microcontrollers at the time.

A system on a chip or system-on-chip is an integrated circuit that integrates most or all components of a computer or other electronic system. These components almost always include on-chip central processing unit (CPU), memory interfaces, input/output devices and interfaces, and secondary storage interfaces, often alongside other components such as radio modems and a graphics processing unit (GPU) – all on a single substrate or microchip. SoCs may contain digital and also analog, mixed-signal and often radio frequency signal processing functions.

The Intel 4004 is a 4-bit central processing unit (CPU) released by Intel Corporation in 1971. Sold for US$60, it was the first commercially produced microprocessor, and the first in a long line of Intel CPUs.

Atmel Corporation was a creator and manufacturer of semiconductors before being subsumed by Microchip Technology in 2016. Atmel was founded in 1984. The company focused on embedded systems built around microcontrollers. Its products included microcontrollers radio-frequency (RF) devices including Wi-Fi, EEPROM, and flash memory devices, symmetric and asymmetric security chips, touch sensors and controllers, and application-specific products. Atmel supplies its devices as standard products, application-specific integrated circuits (ASICs), or application-specific standard product (ASSPs) depending on the requirements of its customers.

<span class="mw-page-title-main">Single-board computer</span> Computer whose components are on a single printed circuit board

A single-board computer (SBC) is a complete computer built on a single circuit board, with microprocessor(s), memory, input/output (I/O) and other features required of a functional computer. Single-board computers are commonly made as demonstration or development systems, for educational systems, or for use as embedded computer controllers. Many types of home computers or portable computers integrate all their functions onto a single printed circuit board.

In-circuit emulation (ICE) is the use of a hardware device or in-circuit emulator used to debug the software of an embedded system. It operates by using a processor with the additional ability to support debugging operations, as well as to carry out the main function of the system. Particularly for older systems, with limited processors, this usually involved replacing the processor temporarily with a hardware emulator: a more powerful although more expensive version. It was historically in the form of bond-out processor which has many internal signals brought out for the purpose of debugging. These signals provide information about the state of the processor.

The Fairchild F8 is an 8-bit microprocessor system from Fairchild Semiconductor, announced in 1974 and shipped in 1975. The original processor family included four main 40-pin integrated circuits (ICs); the 3850 CPU which was the arithmetic logic unit, the 3851 Program Storage Unit (PSU) which contained 1 KB of program ROM and handled instruction decoding, and the optional 3852 Dynamic Memory Interface (DMI) or 3853 Static Memory Interface (SMI) to control additional RAM or ROM holding the user programs or data. The 3854 DMA was another optional system that added direct memory access into the RAM controlled by the 3852.

A general-purpose input/output (GPIO) is an uncommitted digital signal pin on an integrated circuit or electronic circuit board which may be used as an input or output, or both, and is controllable by software.

Each time Intel launched a new microprocessor, they simultaneously provided a system development kit (SDK) allowing engineers, university students, and others to familiarise themselves with the new processor's concepts and features. The SDK single-board computers allowed the user to enter object code from a keyboard or upload it through a communication port, and then test run the code. The SDK boards provided a system monitor ROM to operate the keyboard and other interfaces. Kits varied in their specific features but generally offered optional memory and interface configurations, a serial terminal link, audio cassette storage, and EPROM program memory. Intel's Intellec development system could download code to the SDK boards.

N8VEM was a homebrew computing project. It featured a variety of free and open hardware and software. N8VEM builders made their own homebrew computer systems for themselves and shared their experiences with other homebrew computer hobbyists. N8VEM homebrew computer components are made in the style of vintage computers of the mid to late 1970s and early 1980s using a mix of classic and modern technologies. They are designed with ease of amateur assembly in mind.

The Arduino Uno is an open-source microcontroller board based on the Microchip ATmega328P microcontroller (MCU) and developed by Arduino.cc and initially released in 2010. The microcontroller board is equipped with sets of digital and analog input/output (I/O) pins that may be interfaced to various expansion boards (shields) and other circuits. The board has 14 digital I/O pins, 6 analog I/O pins, and is programmable with the Arduino IDE, via a type B USB cable. It can be powered by a USB cable or a barrel connector that accepts voltages between 7 and 20 volts, such as a rectangular 9-volt battery. It has the same microcontroller as the Arduino Nano board, and the same headers as the Leonardo board. The hardware reference design is distributed under a Creative Commons Attribution Share-Alike 2.5 license and is available on the Arduino website. Layout and production files for some versions of the hardware are also available.

The NEC μCOM series is a series of microprocessors and microcontrollers manufactured by NEC in the 1970s and 1980s. The initial entries in the series were custom-designed 4 and 16-bit designs, but later models in the series were mostly based on the Intel 8080 and Zilog Z80 8-bit designs, and later, the Intel 8086 16-bit design. Most of the line was replaced in 1984 by the NEC V20, an Intel 8088 clone.

<span class="mw-page-title-main">RP2040</span> ARM-architecture microcontroller by the Raspberry Pi Foundation

RP2040 is a 32-bit dual ARM Cortex-M0+ microcontroller integrated circuit by Raspberry Pi Ltd. In January 2021, it was released as part of the Raspberry Pi Pico board.

References

↑ Peter Grigson; David Harris (August–October 1983). "'Marvin' - Z80 Control Computer". Electronics Today International .
↑ Intel SBC 80/10 Single Board Computer brochure, 1976
↑ Mike Bedford (August–September 1983). "Universal EPROM Programmer". Electronics Today International : 45–51, 37–39.
↑ "KIM 1". Old Computers.com.{{cite web}}: External link in |publisher= (help)
↑ "Microprofessor Training System". Flite Electronics International. Archived from the original on 9 May 2008.
↑ Arduino's home page
1 2 "Project homepage". Dwengo.{{cite web}}: External link in |publisher= (help)
↑ Arduino User's forum
↑ "Project homepage". Arduino project.{{cite web}}: External link in |publisher= (help)
↑ Timothy L. Warner. "Hacking Raspberry Pi". 2013. p. 12.
↑ Wiring.org's Wiring development platform home page
↑ "Wiring: Hardware". Wiring project.{{cite web}}: External link in |publisher= (help)

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[ETI,_Marvin-1] Peter Grigson; David Harris (August–October 1983). "'Marvin' - Z80 Control Computer". Electronics Today International .

[2] Intel SBC 80/10 Single Board Computer brochure, 1976

[ETI,_EPROM_Programmer-3] Mike Bedford (August–September 1983). "Universal EPROM Programmer". Electronics Today International : 45–51, 37–39.

[KIM_1-4] "KIM 1". Old Computers.com.{{cite web}}: External link in |publisher= (help)

[Microprofessor-5] "Microprofessor Training System". Flite Electronics International. Archived from the original on 9 May 2008.

[6] Arduino's home page

[Dwengo-7] 1 2 "Project homepage". Dwengo.{{cite web}}: External link in |publisher= (help)

[8] Arduino User's forum

[Arduino,_Project_homepage-9] "Project homepage". Arduino project.{{cite web}}: External link in |publisher= (help)

[10] Timothy L. Warner. "Hacking Raspberry Pi". 2013. p. 12.

[11] Wiring.org's Wiring development platform home page

[Wiring-12] "Wiring: Hardware". Wiring project.{{cite web}}: External link in |publisher= (help)

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]