Z-class | |
---|---|
Manufacturer | Comeng |
Designer | Melbourne & Metropolitan Tramways Board |
Assembly | Dandenong |
Constructed | 1975–1983 |
Entered service | 1975 |
Number built | 230 |
Number in service | 87 |
Number preserved | 6 |
Number scrapped | 34 |
Successor | |
Fleet numbers |
|
Capacity |
|
Depots | |
Specifications | |
Train length |
|
Width | 2.67 m (8 ft 9 in) |
Height |
|
Doors | 4 double, 2 single (Z3 only) |
Wheel diameter |
|
Wheelbase | 1.8 m (5 ft 11 in) |
Maximum speed |
|
Weight |
|
Traction system | |
Traction motors |
|
Power output |
|
Acceleration | 1.5 m/s2 (3.4 mph/s) |
Deceleration |
|
Electric system(s) | 600 V DC (nominal) from overhead catenary |
Current collector(s) | Pantograph |
UIC classification |
|
Bogies |
|
Track gauge | 1,435 mm (4 ft 8+1⁄2 in) standard gauge |
Notes/references | |
[2] [3] [4] [1] |
The Z-class are single-unit bogie trams that operate on the Melbourne tram network. Between 1975 and 1983, 230 trams spanning three sub-classes were built by Comeng, Dandenong. The design was based on two similar Gothenburg tram models, and a prototype built by the Melbourne & Metropolitan Tramways Board. While the Z1 and Z2-class trams were very similar, the Z3-class had significant design changes.
Since introduction they have had a variety of liveries, and modifications. The Z1 and Z2-class trams have been retired, with 87 Z3-class trams remaining in service.
When Melbourne & Metropolitan Tramways Board (MMTB) staff were sent to Europe in 1965 to investigate other tramway operations, they took interest in Swedish trams, and upon return in 1966 drew up specifications, and had a timber mockup built. This mockup was to be the basis for a new tram design for Melbourne. The MMTB approved of the design, and in 1972 requested a prototype be constructed, the result was PCC 1041 being built at Preston Workshops. It was 'European in appearance' and utilised some components bought new, and many recycled from an earlier prototype tram, PCC 980. [5] : 195–196 Prototype PCC 1041 became the basis of the Z-class trams, influenced by the M28 design running in Gothenburg, Sweden. PCC 1041 was to be launched by Premier Rupert Hamer on 26 August 1973, but the tram failed at the launch in front of the media. Due to constant electrical failures, PCC 1041 was infrequently used and was out of service between April 1975 and October 1976. PCC 1041 was finally withdrawn in 1984. [6]
Despite the failure of PCC 1041, 100 Z1-class trams were ordered. Between 1974 and 1983, a total of 230 Z1 to Z3-class trams were built by Comeng at Dandenong. [5] : 197 [7] : 32
Between 1995 and 1999, the remaining 106 Z1s and Z2s were refurbished by Goninan. [8] The bodies were overhauled in an area of Preston Workshops allocated to Goninan, and the bogies were sent to Goninan's Auburn, New South Wales facility. On all except four, the flap type destination displays and route number indicators were replaced by dot-matrix displays. [9] [10] [11]
When the Melbourne tram network was privatised in August 1998, M>Tram was allocated 94 Z1s, 12 Z2s and 84 Z3s, and Yarra Trams received 31 Z3s. Yarra Trams later transferred its Z3s to M>Tram in 2002 as the C class trams arrived to replace them. Yarra Trams’ former units were either refurbished and repainted in M>Tram livery or left in the former Met Green & Yellow livery after their transfer to M>Tram. [12]
It was envisaged that the delivery of the C and D class trams would allow for the Z1 and Z2s to be retired after the 2006 Commonwealth Games, but rising patronage levels necessitated the retention of 30 Z1 and three Z2s until the E class trams entered service from 2014. Half of those remained in service in December 2015, [11] and the last were withdrawn in April 2016. [9]
In late 2007, the Z3s with analogue signage were fitted with digital signage, replacing the original rolling route destination displays. [11] [13]
The Z1 and Z2s were delivered in a livery of marigold (orange) with oriental gold roof; the first four or so were numbered with W2 gold-and-black transfers, but were later changed to the same off-white-and-black as carried by rest of the Z-type in Marigold or Deep Yellow livery. The Z3s were delivered in a livery of deep yellow (pale orange) with a burmese gold roof. For both liveries, the window-level panels were painted off-white (officially "string"), and skirt panels below floor-level were chocolate brown to match the bogies and wheels. From Z3 223 onwards, all were delivered in the Metropolitan Transit Authority's olympic green and wattle yellow livery. [14]
The initial 80 were classified as the 'Z class. After modifications were made to the suspension, the next 20 entered service as the Z1 class. As the first 80 received these modifications, they were reclassified as Z1s. [15] The next two batches were delivered as the Z2 and Z3s'. [9]
In 1972 Rupert Hamer became Premier of Victoria, promising new trams, which had been highlighted as needed in the 1969 Melbourne Transportation Plan. Comeng, in anticipation of a tender, dispatched workers to Europe who, knowing of the fondness within the MMTB of the Swedish tram design, acquired the plans for the Gothenburg M29 tram from Hägglund & Söner. It was understood that ASEA would supply the electrical equipment, as they had been involved in the supply of equipment for the Gothenburg M28 which was almost identical to the Gothenburg M29 trams, and had recently acquired the rolling stock division of Hägglund & Söner. [5] : 196–197
Tenders for 100 trams based on prototype PCC 1041's design were called for in 1972 with Comeng awarded a contract in 1973. [16] The plans purchased by Comeng proved to be less useful than anticipated, due to them being metric, single ended (with doors only on one side), and to some extent 'over-designed'. Comeng essentially started anew, but retained elements of the structural design and ASEA as the electrical equipment supplier, who would supply equipment from the Gothenburg M28 design. [5] : 197–198 [17] [18]
There were a number of design changes made which differentiated the Z-class from PCC 1041, including the destination display arrangement. [5] : 198 Internally they, like PCC 1041, had conductors consoles that passengers would have to queue for, and only two doors per side, these two features hampered loading and proved unpopular. [5] : 196 Fitting the ASEA M28 equipment into the Z-class body, which was heavily based on the M29, posed a problem due to the extra doors, tapered ends, and second cab Comeng had added to make them able to operate in Melbourne, this necessitated lengthening the design to accommodate the equipment. [5] : 199
Construction started at Comeng Dandenong in 1974, with Dandenong's workforce tripling to cope with the order. [5] : 199–200 The first Z1-class tram was delivered in December 1974, and the last in May 1978. [5] : 203 Major construction was carried out at Dandenong, with bogie frames fabricated at Granville, and final fit out and commissioning occurring at the MMTB's Preston Workshops. [5] : 199–200, 202
After being unveiled to the press on 30 April 1975, the first entered service on route 64 on 5 May 1975 and the second on route 72 two days later. [19] As more were delivered, the first 15 were concentrated at North Fitzroy depot to operate route 96 from 30 June 1975. [20] [21]
Soon after commissioning it became apparent that the Z-class had ride problems due to stiff suspension, and track differences between Gothenburg and Melbourne. The issues were rectified by the time the 80th tram was constructed, and the fix, rubber secondary suspension, was retrofitted to all trams. The braking systems also had issues, and were seen as insufficient by the MMTB. [5] : 203 [22] : 31
In anticipation of the Z3-class contract, Z1 No. 5 was fitted with chopper control in November 1977 for evaluation purposes and reclassified ZC-class No. 5. [9] [23] Although it was converted back later, the test successfully demonstrated chopper control trams could operate on the Melbourne tram system without causing interference, and all Z3-class trams were fitted with chopper controls. [22] : 31
In March 2006, Z1-class' 81 was returned to service as the Karachi to Melbourne Tram for the 2006 Commonwealth Games. Renumbered W-11 in recognition of buses operated in Karachi, Pakistan famous for their entertainment value, it was decorated with lush designs and played Bhangra and Pakistani music. For the duration of the games it operated on the City Circle. [24] It returned to service in the summer of 2006/07 operating Friday night City Circle services. [25]
Most of Z1-class were withdrawn following the introduction of the C and D class trams in 2001/02. Most were sold at auction, with some being donated to tram museums. The last remaining Z1-class trams were withdrawn on 24 April 2016. [9] [2] Four have been preserved. [26] Their internal refurbishment had less refurbished features than Z3-class, only seat pads and grab rails/anchors were replaced. [27]
Between June 1978 and February 1979, 15 more trams were built as Z2-class, as an extension of the Z1-class' order. These varied very little from the Z1-class, the main visual differences being the deeper bumper (6-channel like the Z3-class; Z1-class having 4-channel bumpers), and the slide-opening portion of the drivers side-window also being deeper (although at least one Z2 later had a Z1-type drivers side-window fitted). [5] : 203 The final Z2-class tram was withdrawn in April 2016, also being replaced with the C and D trams. [9] [27]
A tender for 100 new trams was called by the MMTB in early 1977, Ansair, Comeng and Siemens tendered. Although Comeng originally planning on using ASEA control equipment, as in the Z1 and Z2-class, they opted to give the MMTB a variety of options, leading to 28 different possible configurations of control equipment, bogies, and suspension types. Comeng were ultimately selected, and between 1979 and 1983, 115 Z3-class trams were built. [22] : 31–36
Although superficially similar to the preceding Z1 and Z2-class trams' externally, they had significant design differences – and were a significant improvement on the Z1 and Z2-class trams. [22] : 31–36 [28] They are fitted with AEG control equipment and Duewag bogies, have an additional door each side (for a total of three rather than two for the Z1 and Z2), drop down (as opposed to top sliding) Beclawat windows and improved headlights. The unreliable flap type destination displays and route number indicators were replaced by rolling plastic film destination displays. They also had much smoother acceleration and braking performance, and improved suspension. Even though the rear door is only half-width (2-leaf, as opposed to the others being 4-leaf), this in combination with the centre doors being directly opposite contributed to better passenger-flow. The Z3-class build process went smoothly, with few problems, bar a slow delivery of equipment from AEG, and a few minor faults that required remedying after construction. [7] : 32 [22] : 31–36 [29] One (Z3 149) was scrapped after being destroyed in a fire in 1999. [30]
On 31 July 2000, Z3 214 was used to convey the Olympic flame along Dandenong Road from the intersection with Hawthorn Road to Chapel Street as part of the 2000 Summer Olympics torch relay. [31] On 26 October 2011, Z3 158, specially liveried as a Royal Tram was used to convey Queen Elizabeth II and Prince Philip along St Kilda Road from Federation Square to Government House during their visit to Melbourne. The Royal Tram remained in regular service until February 2013. [32] [33] [34] [35]
In 2013, a program commenced to refurbish all remaining 114 Z3-class trams at Preston Workshops. They received new seats, painted interior walls, glass replacement with scratch proof film applied, and the Public Transport Victoria livery at Preston Workshops. [36] [37]
As of March 2022, 101 Z3-class trams remain in service. [4]
Between 2022 and 2023, 97 Z3-class trams remain in service as 17 Z3-class trams withdrawn including 5 Z3-class trams scrapped.
The Z3-class operate on the following routes:
Several have been preserved:
The Melbourne tramway network is a tramway system serving the city of Melbourne, Victoria, Australia. The tramway network is centred around the Melbourne central business district (CBD) and consists of approximately 1,700 tram stops across 24 routes. It is the largest operational urban tram network in the world and one of the most used, with more than 500 trams and 250 kilometres of double tram track. It carried 154.8 million passengers over the year 2023-24. Trams are the second most utilised form of public transport in Melbourne after the city's metropolitan commuter railway network.
The Presidents' Conference Committee (PCC) is a streetcar design that was first built in the United States in the 1930s. The design proved successful domestically, and after World War II it was licensed for use elsewhere in the world where PCC based cars were made. The PCC car has proved to be a long-lasting icon of streetcar design, and many remain in service around the world.
Melbourne tram route 5 is operated by Yarra Trams on the Melbourne tram network from Melbourne University to Malvern. The 12.6-kilometre (7.8 mi) route is operated out of Malvern depot with Z and D1 class trams.
Melbourne tram route 75 is operated by Yarra Trams on the Melbourne tram network from Vermont South to Central Pier. The 22.8 kilometre route is operated out of Camberwell depot with A and B class trams. It is the longest route on the network.
Melbourne tram route 67 is operated by Yarra Trams on the Melbourne tram network from Melbourne University to Carnegie. The 12.7-kilometre (7.9 mi) route is operated out of Glenhuntly depot with Z and B class trams.
The A-class Melbourne tram is a class of bogie trams that operate on the Melbourne tram network. Seventy were built by Comeng, Dandenong between 1984 and 1987 in two batches, 28 A1s and 42 A2s, with only minor differences. They are the smallest trams by capacity currently operating on the network.
Melbourne tram route 64 is operated by Yarra Trams on the Melbourne tram network from Melbourne University to East Brighton. The 18.1 kilometre route is operated out of Glenhuntly depot with Z and B class trams.
Melbourne tram route 86 is operated by Yarra Trams on the Melbourne tram network from Bundoora RMIT to Waterfront City. The 22.2-kilometre (13.8 mi) route is operated out of Preston depot with E class trams.
The B-class Melbourne tram is a class of two-section, three-bogie articulated class trams that operate on the Melbourne tram network. Following the introduction of two B1-class prototype trams in 1984 and 1985, a total of 130 B2-class trams were built by Comeng, Dandenong.
The Melbourne & Metropolitan Tramways Board (MMTB) was a government-owned authority that was responsible for the tram network in Melbourne, Australia between 1919 and 1983, when it was merged into the Metropolitan Transit Authority. It had been formed by the merger of a number of smaller tramway trusts and companies that operated throughout the city.
The W-class trams are a family of electric trams built by the Melbourne & Metropolitan Tramways Board (MMTB) between 1923 and 1956. Over the 33 years of production, 752 vehicles spanning 12 sub-classes were constructed, the majority at the MMTB's Preston Workshops.
Essendon tram depot is located on Mount Alexander Road, Travancore, a suburb of Melbourne, Victoria, Australia. Operated by Yarra Trams, it is one of eight tram depots on the Melbourne tram network. Despite the name, the depot is located three kilometres from the suburb of Essendon.
The earliest trams in Australia operated in the latter decades of the 19th century, hauled by horses or "steam tram motors". At the turn of the 20th century, propulsion almost universally turned to electrification, although cable trams lingered in Melbourne. In cities and towns that had trams, they were a major part of public transport assets.
M>Tram was a tram operator in Melbourne, Australia. Formed in July 1998 as Swanston Trams, a business unit of the Public Transport Corporation, it was privatised in August 1999 becoming a subsidiary of National Express. In December 2002 National Express handed the franchise in, with the State Government taking over until negotiations were concluded for Yarra Trams to take over in April 2004.
Camberwell tram depot is located on Council Street, Hawthorn East, a suburb of Melbourne, Victoria, Australia. Opened in December 1929, it is operated by Yarra Trams. It is one of eight tram depots on the Melbourne tram network.
Brunswick tram depot is located on Sydney Road, Brunswick, a suburb of Melbourne, Victoria, Australia. It opened on 26 April 1936 in conjunction with the electrification of the Brunswick and North Melbourne Cable tram line. Operated by Yarra Trams, it is one of eight tram depots on the Melbourne tram network.
Preston Workshops is the heavy maintenance facility for the Melbourne tram network. The workshop is located on a block surrounded by Miller Street, St Georges Road, Oakover Road and the Mernda railway line in Preston, a suburb in Melbourne, Victoria, Australia. Following a major redevelopment in April 2016, it also became an operational depot under the name New Preston Depot, taking over from East Preston.
Francis Richard Kirby (1911–1982) was an Australian electrical engineer and tramway administrator. After working at the State Electricity Commission of Victoria as an engineer, Kirby started working for the Melbourne and Metropolitan Tramways Board (MMTB). He became the MMTB's fourth Chairman in 1970, taking over from Robert Risson, and was succeeded by Dudley Snell, the last Chairman of the MMTB, in 1976.
The Melbourne tram network began in 1884 with the construction of the Fairfield Horse Tramway. However, the purpose of the line was to increase land prices in the area, and it soon closed during the depression in 1890. The first genuine attempt to construct a tramway network was the construction of the Richmond cable tram line by the Melbourne Tramway & Omnibus Company in 1885. Over the next few years, 16 more cable tram lines were constructed, as well as numerous other horse tramways. The depression of the early 1890s slowed further expansion of the cable network. The first electric tram line was the Box Hill and Doncaster tramway which opened in 1889. This was a pioneering line in what was then the countryside and thus didn't receive much patronage. It closed in 1896. The next attempt at an electric tramway was Victorian Railways' St Kilda to Brighton line, which opened in 1906. Later that year, the North Melbourne Electric Tramway & Lighting Company opened lines to Essendon and Maribyrnong. Many local councils formed their own tramway trusts and built tramways within their own constituency. The most successful of these was the Prahran & Malvern Tramways Trust.
The M29 is a class of 60 four-axle trams built for use on the Gothenburg Tramway in Sweden between 1969 and 1972. The class is still in passenger service in its home city and carries fleet numbers 801–860, although some members have been withdrawn.
{{cite web}}
: CS1 maint: archived copy as title (link)Media related to Z class trams at Wikimedia Commons