Oil burner (engine)

Last updated

Oil Burning Locomotive: Southern Pacific 2472 at the Niles Canyon Railway Southern Pacific Railroad 4-6-2 -2472 at Sunol California May 2009.jpg
Oil Burning Locomotive: Southern Pacific 2472 at the Niles Canyon Railway

An oil burner engine is a steam engine that uses oil as its fuel. The term is usually applied to a locomotive or ship engine that burns oil to heat water, to produce the steam which drives the pistons, or turbines, from which the power is derived.

Contents

This is mechanically very different from diesel engines, which use internal combustion, although they are sometimes colloquially referred to as oil burners. [1]

History

A variety of experimental oil powered steam boilers were patented in the 1860s. Most of the early patents used steam to spray atomized oil into the steam boilers furnace. Attempts to burn oil from a free surface were unsuccessful due to the inherently low rates of combustion from the available surface area. [2] [3]

On 21 April 1868, the steam yacht Henrietta made a voyage down the river Clyde powered by an oil fired boiler designed and patented by a Mr Donald of George Miller & Co. [2] [4] Donald's design used a jet of dry steam to spray oil into a furnace lined with fireproof bricks. Prior to the Henrietta’s oil burner conversion, George Miller & Co was recorded as having used oil to power their works in Glasgow for a “considerable time”. [4]

During the late 19th century numerous burner designs were patented using combinations of steam, compressed air and injection pumps to spray oil into boiler furnaces. Most of the early oil burner designs were commercial failures due to the high cost of oil (relative to coal) rather than any technical issues with the burners themselves. [2]

During the early 20th century, marine and large oil burning steam engines generally used electric motor or steam driven injection pumps. Oil would be draw from a storage tank through suction strainers and across, viscosity reducing, oil heaters. The oil would then be pumped through discharge strainers before entering the burners as a whirling mist. Combustion air was introduced through special furnace-fronts, which were fitted with dampers to regulate the supply. Smaller land-based oil burning steam engines typically used steam jets fed from the main boiler to blast atomized oil into the burner nozzles. [5]

Steam ships

In the 1870s, Caspian steamships began using mazut, a residual fuel oil which at that time was produced as a waste stream by the many oil refineries located in the Absheron peninsula. During the late 19th century Mazut remained cheap and plentiful in the Caspian region. [3]

In 1870, either the SS Iran [3] or SS Constantine [6] [7] (depending on source) became the first ship to convert to burning fuel oil, both were Caspian based merchant steamships. [3] [6]

During the 1870s, the Imperial Russian Navy converted the ships of the Caspian fleet to oil burners starting with the Khivenets in 1874. [3]

In 1894, the oil tanker SS Baku Standard became the first oil burning vessel to cross the Atlantic Ocean. In 1903, the Red Star Liner SS Kensington became the first passenger liner to make the Atlantic crossing with boilers fired by fuel oil. [7]

Fuel oil has a higher energy density than coal and oil powered ships did not need to employ stokers however coal remained the dominant power source for marine boilers throughout the 19th century primarily due to the relatively high cost of fuel oil. [3] Oil was used in marine boilers to a greater extent during the early 20th century. By 1939, about half the world’s ships burned fuel oil, of these about half had steam engines and the other half used diesel engines. [6]

Steam locomotives

Oil burners designed by Thomas Urquhart were fitted to the locomotives of the Gryazi-Tsaritsyn railway in southern Russia. [2] Thomas Urquhart, who was employed as a Locomotive Superintendent by the Gryazi-Tsaritsyn Railway Company, began his experiments in 1874. By 1885 all the locomotives of the Gryazi-Tsaritsyn Railway had been converted to run on fuel oil. [8]

In Great Britain, an early pioneer of oil burning railway locomotives was James Holden, [9] [2] of the Great Eastern Railway. In James Holden's system, steam was raised by burning coal before the oil fuel was turned on. [10] Holden's first oil burning locomotive Petrolea, was a class T19 2-4-0. Built in 1893, Petrolea burned waste oil that the railway had previously been discharging into the River Lea. [11] Due to the relatively low cost of coal, oil was rarely used on Britain's streamtrains and in most cases only where there was a shortage of coal. [12]

In the United States, the first oil burning steam locomotive was in service on the Southern Pacific railroad by 1900. [13] By 1915 there were 4,259 oil burning steam locomotives in the United States, which represented 6.5% of all the locomotives then in service. [13] Most oil burners were operated in areas west of the Mississippi where oil was abundant. [13] American usage of oil burning steam locomotives peaked in 1945 when they were responsible for around 20% of all the fuel consumed (measured by energy content) during rail freight operations. [14] After WW2, both oil and coal burning steam locomotives were replaced by more efficient diesel engines and had been almost entirely phased out of service by 1960. [14]

Notable early oil-fired steamships

Passenger liners

Warships

USS Trippe, an oil-fired steamship, one of the US Navy's Paulding class destroyers USS Trippe (DD-33).jpg
USS Trippe, an oil-fired steamship, one of the US Navy's Paulding class destroyers

Notable oil-fired steam locomotives

General

Australia

India

Great Britain

New Zealand

North America

('*' symbol indicates locomotive was converted or is being converted from coal-burning to oil-burning in either revenue service or excursion service)

See also

Related Research Articles

<span class="mw-page-title-main">Steam locomotive</span> Railway locomotive that produces its pulling power through a steam engine

A steam locomotive is a locomotive that provides the force to move itself and other vehicles by means of the expansion of steam. It is fuelled by burning combustible material to heat water in the locomotive's boiler to the point where it becomes gaseous and its volume increases 1,700 times. Functionally, it is a steam engine on wheels.

<span class="mw-page-title-main">Mallet locomotive</span> Articulated locomotive with compound steam power

A Mallet locomotive is a type of compound articulated steam locomotive, invented by the Swiss engineer Anatole Mallet (1837–1919).

<span class="mw-page-title-main">Tender (rail)</span> Steam locomotive fuel and water tank container

A tender or coal-car is a special rail vehicle hauled by a steam locomotive containing its fuel and water. Steam locomotives consume large quantities of water compared to the quantity of fuel, so their tenders are necessary to keep them running over long distances. A locomotive that pulls a tender is called a tender locomotive. Locomotives that do not have tenders and carry all their fuel and water on board the locomotive itself are called tank locomotives or tank engines.

<span class="mw-page-title-main">Union Pacific 737</span> Preserved American 4-4-0 locomotive

Union Pacific Railway Engine No. 737 or UP 737 is a 4-4-0 "American" type steam locomotive. It is currently the oldest preserved Union Pacific steam locomotive. It was originally acquired by the Union Pacific Railroad (UP) in 1887.

<span class="mw-page-title-main">4-6-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of locomotives, 4-6-4 represents the wheel arrangement of four leading wheels, six powered and coupled driving wheels and four trailing wheels. In France where the type was first used, it is known as the Baltic while it became known as the Hudson in most of North America.

<span class="mw-page-title-main">4-8-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, 4-8-4 represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees have shortened the name since its introduction. It is most-commonly known as a Northern.

Under the Whyte notation for the classification of steam locomotives, 2-10-2 represents the wheel arrangement of two leading wheels, ten powered and coupled driving wheels, and two trailing wheels. In the United States and elsewhere the 2-10-2 is known as the Santa Fe type, after the Atchison, Topeka and Santa Fe Railway that first used the type in 1903.

<span class="mw-page-title-main">California State Railroad Museum</span> Railroad museum in Sacramento, California

The California State Railroad Museum is a museum in the California State Parks system that interprets the role of railroads in the West. It is located in Old Sacramento State Historic Park at 111 I Street, Sacramento, California.

<span class="mw-page-title-main">2-6-2</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, 2-6-2 represents the wheel arrangement of two leading wheels, six coupled driving wheels and two trailing wheels. This arrangement is commonly called a Prairie.

<span class="mw-page-title-main">Live steam</span> Steam-powered models and toys

Live steam is steam under pressure, obtained by heating water in a boiler. The steam may be used to operate stationary or moving equipment.

<span class="mw-page-title-main">Grand Canyon Railway</span> Historic railway to Grand Canyon National Park in Arizona

The Grand Canyon Railway is a heritage railroad which carries passengers between Williams, Arizona, and the South Rim of Grand Canyon National Park.

<span class="mw-page-title-main">Baldwin 60000</span> Preserved steam locomotive

Baldwin 60000 is an experimental steam locomotive built by the Baldwin Locomotive Works in Eddystone, Pennsylvania, in 1926, during the height of the railroading industry. It received its number for being the 60,000th locomotive built by Baldwin.

<span class="mw-page-title-main">Southern Pacific 2479</span> Preserved SP P-10 class 4-6-2 locomotive

Southern Pacific 2479 is one of six 4-6-2 heavy "Pacific" type steam locomotives built by Baldwin Locomotive Works in 1923 for the Southern Pacific Railroad (SP), designated the P-10 class. No. 2479 was retired from service in 1956. The locomotive is currently undergoing restoration to operating condition by the Pacific Locomotive Association at Brightside, California.

<span class="mw-page-title-main">Steam generator (railroad)</span>

A steam generator is a type of boiler used to produce steam for climate control and potable water heating in railroad passenger cars. The output of a railroad steam generator is low pressure, saturated steam that is passed through a system of pipes and conduits throughout the length of the train.

NZR J<sup>A</sup> class

The NZR JA class was a class of fifty-one 4-8-2 steam locomotives operated by the New Zealand Railways Department (NZR). The locomotives were built in two batches; the first batch was constructed in-home at the Hillside Workshops at Dunedin between 1946 and 1956, while the second batch was produced by the North British Locomotive Company (NBL) of Glasgow, Scotland in 1951. To differentiate between the two batches, the locomotives were identified by their builder.

NZR K<sup>A</sup> class

The NZR KA class of 1939 was a class of mixed traffic 4-8-4 steam locomotives that operated on New Zealand's railway network. They were built after the success of the K class to meet the increasing traffic demands of the New Zealand Railways Department. The locomotives first appeared with distinctive streamlining, mainly to hide their ACFI feedwater heater systems.

<span class="mw-page-title-main">NZR J class (1939)</span>

The NZR J class was a class of forty 4-8-2 steam locomotives operated by the New Zealand Railways Department (NZR). Although designed to work on the lighter secondary lines, the class was frequently used on mainline express passenger trains as well as freight. When first introduced, the class boasted distinctive streamlining, which was later removed from 1947 onwards for maintenance reasons. Three of this class remained in service until the end of steam operation on 26 October 1971, when they were withdrawn and entered into preservation. This class should not be confused with the earlier J class from 1874.

<span class="mw-page-title-main">New South Wales D55 class locomotive</span>

The D55 class was a class of 2-8-0 steam locomotives built by Clyde Engineering for the New South Wales Government Railways in Australia.

<span class="mw-page-title-main">GWR 101 Class</span> Unique oil-burning steam locomotive

The GWR 101 Class consisted of a single experimental 0-4-0T side-tank steam locomotive. It was built at GWR Swindon Works under the direction of George Jackson Churchward in June 1902.

<span class="mw-page-title-main">Spokane, Portland and Seattle 539</span> Preserved American 2-8-2 locomotive

Spokane, Portland and Seattle Railway No. 539 is the only preserved example of the class O-3 2-8-2 "Mikado" steam locomotive. It was built by the American Locomotive Company in 1917 for the Northern Pacific Railway as engine No. 1762. It was sold to the Spokane, Portland and Seattle Railway and renumbered 539, in August 1944. It was reconfigured and converted to oil burning in January 1946. The locomotive was retired in 1957, and it was displayed in Esther Short Park, Washington, until 1997. That year, it was moved to Battle Ground for a potential restoration that never came to fruition. In 2007, it was acquired by the Grand Canyon Railway and moved to Williams, Arizona for an operational restoration that also never came to fruition. In 2019, No. 539 was purchased again by the Port of Kalama, who moved it back to Washington and put it on static display inside the Port's Interpretive Center that was constructed in 2014.

References

  1. ↑ Spinelli, Mike (25 May 2006). "Diesel on the Range: Land Rover Flagship to Come in Oil-Burner". Jalopnik . Retrieved 8 September 2017.
  2. 1 2 3 4 5 6 Bertin, L.E; Robertson, Leslie S (1906). "Chapter 5 - Liquid Fuel". Marine Boilers. D Van Nostrand Company, New York. pp. 121–170.
  3. 1 2 3 4 5 6 Henry, James Dodds (March 1908). "Chapter 1 - The Growth of a Great Industry". Oil Fuel and the Empire. Bradbury Agnew & Co, London. pp. 29–53.
  4. 1 2 "Liquid fuel for steamers". North British Daily Mail: 4. 24 April 1868.
  5. ↑ Baillie, A F (December 1925). "The Commercial Application of Fuel Oil". The Shipbuilder-The Journal of the Shipbuilding, Marine Engineering and Allied Industries. Institution of Engineers and Shipbuilders in Scotland. 33 (Jan-Dec 1926): 264–265.
  6. 1 2 3 Winkler, Matthew (2003). "Introduction to Marine Petroleum Fuels". Fuels and Lubricants Handbook. ASTM International. p. 145.
  7. 1 2 Henry, James Dodds (1907). Thirty Five Years of Oil Transport. Bradbury Agnew & Co, London. p. 8.
  8. ↑ "Thomas_Urquhart". Graces Guides to British Industrial History. Retrieved 30 October 2021.
  9. ↑ Jones, Cletus H. (1985). Marine Fuels. ASTM International. p. 87. ISBN   0-8031-0425-1 – via Google Books.
  10. ↑ "Locomotive History of the GER". The London & North Eastern Railway Encyclopedia.
  11. ↑ Brooks, Lyn D. "Fuel energy & steam traction" . Retrieved 24 July 2008.
  12. ↑ Sabourin, A. (July 1913). "Notes sur l'industrie des transports". La Technique Moderne. 5: 36–37.
  13. 1 2 3 Morrison, Tom (2018). The American Steam Locomotive in the Twentieth Century. McFarland and Company Inc. pp. 201–202. ISBN   978-1476679006.
  14. 1 2 Iden, Michael (25 October 2017). US Freight Rail Fuel Efficiency 1920-2015 & beyond (PDF). 19th Railroad Environmental Conference. The University of Illinois Urbana-Champaign. Archived from the original (PDF) on 24 February 2006. Retrieved 18 August 2022.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.