Self-complementary antenna

Last updated

The self-complementary antenna (SCA) is a basic antenna for extremely broadband practical antennas. [1] [2] [3] [4] This antenna [5] [6] is an arbitrarily shaped antenna which is constituted with a half of an infinitely extended planar-sheet conductor such that the shape of its complementary structure is exactly identical, or "self-complementary" [7] with that of the original structure with two terminals for the simplest case. The self-complementary antenna has constant input impedance [8] [9] independent of the source frequency and the shape of the structure.

Contents

The type of the self-complementary antenna is not limited only to the case of a planar antenna with two terminals, but there are more general types with various grades of complexity, such as, the number of terminals, the number of reference planes, and others. Moreover, there is infinite freedom in their shapes of the structures. [10] They also have constant-impedance property independent of the source frequency and the shape of the structure for respective classes of structures with various grades of complexity. This general principle of self-complementarity is also called the "Mushiake Principle" by various sources. [11]

Examples for two shapes of the structures are shown in the attached figures. The structures 1 to 3 are for square shape, [12] and the structures 4 to 6 are spiral shape. Actually, the structures extend infinitely, but the figures show only finite portions near the feed point of each structure.

The equation which gives the constant value of the input impedance for self-complementary antenna is called the "Mushiake Relationship". The values of the constant-impedance for various classes of complexity in the self-complementary structures depend on the respective grades of the complexity. For example, the Mushiake relationship for the simplest self-complementary planar antenna with two terminals is expressed as:

Z = Z0/2≒188.4 [Ω], (Mushiake relationship)

where Z is the input impedance of the antenna, and Z0 is the intrinsic impedance of the medium.

Moreover, experimental studies on self-complementary antennas, including radiation properties, are conducted in Japan. As the results of the experiment, it is found that the truncated alternate-leaves type self-complementary antenna (or Square SCA) has practically omnidirectional radiation pattern [13] as well as the broadband property.

Comparison with log-periodic antennas

The log-periodic antenna is a modified, folded up, square self-complementary antenna with log-periodic shape, and the original structure before its modification has a typical self-complementary shape. The log-periodic shape does not provide the broadband property for antennas. [14] This fact is experimentally proven. [15] It is also evident from the IEEE definition of "Log-Periodic Antenna". [16] The "Log-Periodic Dipole Array" [17] or "Log-Periodic Dipole Antenna" [18] (LPDA), is a practically modified self-complementary antenna. LPDA has transposed excitation [19] for the dipole array resulted from folding up [20] the antenna structure to obtain unidirectional radiation, that is inevitable outcome of the modification.

In connection with the book Self-complementary Antennas published at the Springer-Verlag in London, is mentioned here,Springer Book Archives [21] should be shown around here.

The log-periodic structure failed to provide constant-impedance property for antennas over one period. However, one certain way to eliminate such variation is to make the shape self-complementary, [22] and the expression for the constant impedance is called "Mushiake's relation" by V. H. Rumsey.(Recently it is called〝Mushiake　relationship".)

Accordingly, LPDA is actually a Modified Self-complementary Dipole Array (MSCDA) with log-periodic shape. Where the self-complementary shape has infinite freedom [23] and further evolution is expected for general type of broadband dipole array, MSCDA. For example, with recent widespread Wi-Fi utilization, this type of broadband MSCDA is found, including so-called LPDA, at the Wi-Fi access points.

Furthermore, "Discovery of the Principle of Self-Complementarity in Antennas and the Mushiake Relationship, 1948" was recognized as IEEE Milestone July 2017, without mentioning the needless term "log-periodic shape" for that recognition. Moreover, to be proposed as an IEEE Milestone, an achievement must be at least 25 years old, have benefited humanity, and must have had at least regional importance. This IEEE Milestone was dedicated to Tohoku University, Japan, and detailed explanation can be found in the List of Milestones, [24] or more easily found in. [25] In addition, a noun "Milestone" means "a very important stage or event in the development of something", and "Landmark" is its synonym. Source is, [26] Oxford University Press, 2015.

See also

Related Research Articles

<span class="mw-page-title-main">Log-periodic antenna</span> Multi-element, directional antenna useable over a wide band of frequencies

A log-periodic antenna (LP), also known as a log-periodic array or log-periodic aerial, is a multi-element, directional antenna designed to operate over a wide band of frequencies. It was invented by John Dunlavy in 1952.

<span class="mw-page-title-main">Radiation pattern</span> Directional variation in strength of radio waves

In the field of antenna design the term radiation pattern refers to the directional (angular) dependence of the strength of the radio waves from the antenna or other source.

<span class="mw-page-title-main">Gain (antenna)</span> Telecommunications performance metric

In electromagnetics, an antenna's gain is a key performance parameter which combines the antenna's directivity and radiation efficiency. The term power gain has been deprecated by IEEE. In a transmitting antenna, the gain describes how well the antenna converts input power into radio waves headed in a specified direction. In a receiving antenna, the gain describes how well the antenna converts radio waves arriving from a specified direction into electrical power. When no direction is specified, gain is understood to refer to the peak value of the gain, the gain in the direction of the antenna's main lobe. A plot of the gain as a function of direction is called the antenna pattern or radiation pattern. It is not to be confused with directivity, which does not take an antenna's radiation efficiency into account.

<span class="mw-page-title-main">Fractal antenna</span> Antenna with a fractal shape

A fractal antenna is an antenna that uses a fractal, self-similar design to maximize the effective length, or increase the perimeter, of material that can receive or transmit electromagnetic radiation within a given total surface area or volume.

<span class="mw-page-title-main">Antenna (radio)</span> Electrical device

In radio engineering, an antenna or aerial is the interface between radio waves propagating through space and electric currents moving in metal conductors, used with a transmitter or receiver. In transmission, a radio transmitter supplies an electric current to the antenna's terminals, and the antenna radiates the energy from the current as electromagnetic waves. In reception, an antenna intercepts some of the power of a radio wave in order to produce an electric current at its terminals, that is applied to a receiver to be amplified. Antennas are essential components of all radio equipment.

<span class="mw-page-title-main">Biconical antenna</span>

In radio systems, a biconical antenna is a broad-bandwidth antenna made of two roughly conical conductive objects, nearly touching at their points.

<span class="mw-page-title-main">Effective radiated power</span> Definition of directional radio frequency power

Effective radiated power (ERP), synonymous with equivalent radiated power, is an IEEE standardized definition of directional radio frequency (RF) power, such as that emitted by a radio transmitter. It is the total power in watts that would have to be radiated by a half-wave dipole antenna to give the same radiation intensity as the actual source antenna at a distant receiver located in the direction of the antenna's strongest beam. ERP measures the combination of the power emitted by the transmitter and the ability of the antenna to direct that power in a given direction. It is equal to the input power to the antenna multiplied by the gain of the antenna. It is used in electronics and telecommunications, particularly in broadcasting to quantify the apparent power of a broadcasting station experienced by listeners in its reception area.

In physics, Babinet's principle states that the diffraction pattern from an opaque body is identical to that from a hole of the same size and shape except for the overall forward beam intensity. It was formulated in the 1800s by French physicist Jacques Babinet.

This is an index of articles relating to electronics and electricity or natural electricity and things that run on electricity and things that use or conduct electricity.

<span class="mw-page-title-main">Yagi–Uda antenna</span> Type of radio antenna

A Yagi–Uda antenna, or simply Yagi antenna, is a directional antenna consisting of two or more parallel resonant antenna elements in an end-fire array; these elements are most often metal rods acting as half-wave dipoles. Yagi–Uda antennas consist of a single driven element connected to a radio transmitter and/or receiver through a transmission line, and additional "passive radiators" with no electrical connection, usually including one so-called reflector and any number of directors. It was invented in 1926 by Shintaro Uda of Tohoku Imperial University, Japan, with a lesser role played by his boss Hidetsugu Yagi.

<span class="mw-page-title-main">Rhombic antenna</span> Rhombus-shaped antenna

A rhombic antenna is made of four sections of wire suspended parallel to the ground in a diamond or "rhombus" shape. Each of the four sides is the same length – about a quarter-wavelength to one wavelength per section – converging but not touching at an angle of about 42° at the fed end and at the far end. The length is not critical, typically from one to two wavelengths (λ), but there is an optimum angle for any given length and frequency. A horizontal rhombic antenna radiates horizontally polarized radio waves at a low elevation angle off the pointy ends of the antenna.

<span class="mw-page-title-main">Dipole antenna</span> Antenna consisting of two rod shaped conductors

In radio and telecommunications a dipole antenna or doublet is the simplest and most widely used class of antenna. The dipole is any one of a class of antennas producing a radiation pattern approximating that of an elementary electric dipole with a radiating structure supporting a line current so energized that the current has only one node at each end. A dipole antenna commonly consists of two identical conductive elements such as metal wires or rods. The driving current from the transmitter is applied, or for receiving antennas the output signal to the receiver is taken, between the two halves of the antenna. Each side of the feedline to the transmitter or receiver is connected to one of the conductors. This contrasts with a monopole antenna, which consists of a single rod or conductor with one side of the feedline connected to it, and the other side connected to some type of ground. A common example of a dipole is the "rabbit ears" television antenna found on broadcast television sets.

<span class="mw-page-title-main">Microstrip antenna</span>

In telecommunication, a microstrip antenna usually means an antenna fabricated using photolithographic techniques on a printed circuit board (PCB). It is a kind of internal antenna. They are mostly used at microwave frequencies. An individual microstrip antenna consists of a patch of metal foil of various shapes on the surface of a PCB, with a metal foil ground plane on the other side of the board. Most microstrip antennas consist of multiple patches in a two-dimensional array. The antenna is usually connected to the transmitter or receiver through foil microstrip transmission lines. The radio frequency current is applied between the antenna and ground plane. Microstrip antennas have become very popular in recent decades due to their thin planar profile which can be incorporated into the surfaces of consumer products, aircraft and missiles; their ease of fabrication using printed circuit techniques; the ease of integrating the antenna on the same board with the rest of the circuit, and the possibility of adding active devices such as microwave integrated circuits to the antenna itself to make active antennas Patch antenna

A loop antenna is a radio antenna consisting of a loop or coil of wire, tubing, or other electrical conductor, that is usually fed by a balanced source or feeding a balanced load. Within this physical description there are two distinct types:

<span class="mw-page-title-main">Monopole antenna</span> Type of radio antenna

A monopole antenna is a class of radio antenna consisting of a straight rod-shaped conductor, often mounted perpendicularly over some type of conductive surface, called a ground plane. The driving signal from the transmitter is applied, or for receiving antennas the output signal to the receiver is taken, between the lower end of the monopole and the ground plane. One side of the antenna feedline is attached to the lower end of the monopole, and the other side is attached to the ground plane, which is often the Earth. This contrasts with a dipole antenna which consists of two identical rod conductors, with the signal from the transmitter applied between the two halves of the antenna.

James R. Wait was a Canadian electrical engineer and engineering physicist. In 1977, he was elected as a member of National Academy of Engineering in Electronics, Communication & Information Systems Engineering for his contributions to electromagnetic propagation engineering as it affects communication and geophysical exploration.

A shortwave broadband antenna is a radio antenna that can be used for transmission of any shortwave radio band from among the greater part of the shortwave radio spectrum, without requiring any band-by-band adjustment of the antenna. Generally speaking, there is no difficulty in building an adequate receiving antenna; the challenge is designing an antenna which can be used for transmission without an adjustable impedance matching network.

<span class="mw-page-title-main">Tunable metamaterial</span>

A tunable metamaterial is a metamaterial with a variable response to an incident electromagnetic wave. This includes remotely controlling how an incident electromagnetic wave interacts with a metamaterial. This translates into the capability to determine whether the EM wave is transmitted, reflected, or absorbed. In general, the lattice structure of the tunable metamaterial is adjustable in real time, making it possible to reconfigure a metamaterial device during operation. It encompasses developments beyond the bandwidth limitations in left-handed materials by constructing various types of metamaterials. The ongoing research in this domain includes electromagnetic materials that are very meta which mean good and has a band gap metamaterials (EBG), also known as photonic band gap (PBG), and negative refractive index material (NIM).

<span class="mw-page-title-main">Antenna array</span>

An antenna array is a set of multiple connected antennas which work together as a single antenna, to transmit or receive radio waves. The individual antennas are usually connected to a single receiver or transmitter by feedlines that feed the power to the elements in a specific phase relationship. The radio waves radiated by each individual antenna combine and superpose, adding together to enhance the power radiated in desired directions, and cancelling to reduce the power radiated in other directions. Similarly, when used for receiving, the separate radio frequency currents from the individual antennas combine in the receiver with the correct phase relationship to enhance signals received from the desired directions and cancel signals from undesired directions. More sophisticated array antennas may have multiple transmitter or receiver modules, each connected to a separate antenna element or group of elements.

<span class="mw-page-title-main">Frequency selective surface</span> Optical filter

A frequency-selective surface (FSS) is any thin, repetitive surface designed to reflect, transmit or absorb electromagnetic fields based on the frequency of the field. In this sense, an FSS is a type of optical filter or metal-mesh optical filters in which the filtering is accomplished by virtue of the regular, periodic pattern on the surface of the FSS. Though not explicitly mentioned in the name, FSS's also have properties which vary with incidence angle and polarization as well - these are unavoidable consequences of the way in which FSS's are constructed. Frequency-selective surfaces have been most commonly used in the radio frequency region of the electromagnetic spectrum and find use in applications as diverse as the aforementioned microwave oven, antenna radomes and modern metamaterials. Sometimes frequency selective surfaces are referred to simply as periodic surfaces and are a 2-dimensional analog of the new periodic volumes known as photonic crystals.

References

  1. ↑ D. E. Isbell, "Log-periodic dipole arrays" IRE Trans. Antennas Propag., vol. AP-8, pp.260-267, May 1960.
  2. ↑ R. L. Carrel, "The design of log-periodic dipole antennas," IRE Intl. Conv. Rec., pt. 1, pp. 61-75, 1961
  3. ↑ Y. Mushiake, Log-periodic structure provides no broad-band property for antennas. J. IECE Japan, 82, No 5, pp. 510-511, May 1999. (in Japanese)
  4. ↑ Y. Mushiake, "A report on Japanese developments of antennas: From the Yagi-Uda antenna to self-complementary antennas", IEEE Ant. Prop. Magazine, Vol. 46, No. 4, pp. 47-60, August 2004
  5. ↑ "Y. Mushiake, "The input impedances of slit antennas," J. IEE of Japan, Vol. 69, No. 3, Cumulative No. 725, March 1949. pp. 87-88. (in Japanese)". Sm.rim.or.jp. Retrieved 2014-01-07.
  6. ↑ S. Uda, and Y. Mushiake, "The input impedances of slit antennas," Tech. Rep. of Tohoku Univ., 14, 1, September 1949. pp. 46-59.
  7. ↑ "Y. Mushiake, "Origination of self-complementary structure and discovery of its constant-impedance property." J. IEE of Japan, Vol. 69, No. 3, March 1949. p. 88. (in Japanese)". Sm.rim.or.jp. Retrieved 2014-01-07.
  8. ↑ Y. Mushiake, "The input impedances of slit antennas," J. IEE Japan, 69, 3, March 1949. pp. 87-88. (in Japanese)
  9. ↑ Y. Mushiake, "Constant-impedance antennas," J. IECE Japan, 48, 4, April 1965. pp. 580-584. (in Japanese)
  10. ↑ http://www.sm.rim.or.jp/~ymushiak/sub.sca.htm
  11. ↑ Ranjan Singh, et al; Spiral-type terahertz antennas and the manifestation of the Mushiake principle, OSA Publishing, Optics Express, Volume 17, Issue 12, Page 9971-9980, (2009)https://www.osapublishing.org/abstract.cfm?uri=oe-17-12-9971,
  12. ↑ T. Furuya, T. Ishizone, and Y. Mushiake, "Alternate-leaved Self-complementary Antenna and Its Application to High Gain Broadband Antenna", IECE (presently IEICE), A・P, 77-43, 1977, pp. 35-40. (in Japanese)
  13. ↑ http://www.sm.rim.or.jp/~ymushiak/sub.omni.square.htm
  14. ↑ Y. Mushiake, "Constant-impedance antennas," J. IECE Japan, 48, 4, pp. 580-584, April 1965
  15. ↑ "Fig. 2: A comparison of the measured input resistances".
  16. ↑ "Log-periodic antenna Any one of a class of antennas having a structural geometry such that its impedance and radiation characteristics repeat periodically as the logarithm of frequency."(see The new IEEE Standard Dictionary of Electrical and Electronics Terms,1993).
  17. ↑ D. E. Isbell, "Log-periodic dipole arrays" IRE Trans. Antennas Propag., vol. AP-8, pp.260-267, May 1960.
  18. ↑ R. L. Carrel, "The design of log-periodic dipole antennas," IRE Intl. Conv. Rec., pt.I, pp. 61-75, 1961
  19. ↑ "Y. Mushiake, Self-Complementary Antennas—Principle of Self-Complementarity for Constant Impedance—, 139 pages, Springer-Verlag London Ltd., London,1996.pp.75-80". Sm.rim.or.jp. Retrieved 2019-12-13.
  20. ↑ http://www.sm.rim.or.jp/~ymushiak/sub.4.htm#%%#
  21. ↑ http://www.sm.rim.or.jp/~ymushiak/sub.springer.htm
  22. ↑ V. H. Rumsey, Frequency independent antennas, Academic Press, New York and London. 1966. [pp. 27, 29, 30, 55]
  23. ↑ http://www.sm.rim.or.jp/~ymushiak/sub.sca.htm
  24. ↑ http://ethw.org/Milestones:List_of_Milestones Dedication #　180
  25. ↑ "Milestones:The Discovery of the Principle of Self-Complementarity in Antennas and the Mushiake Relationship, 1948 - Engineering and Technology History Wiki". 3 November 2021.
  26. ↑ Oxford advanced learner's dictionary of current English
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.