Television antenna

Last updated
Antenne VHF UHF.jpg
Two Yagi-Uda type outdoor antennas mounted at the side of a building.
Rabbit-ears dipole antenna with UHF loop 20090204.jpg
A rabbit ears indoor antenna. This model also has a loop antenna for UHF reception.

A television antenna, also called a television aerial (in British English), is an antenna specifically designed for use with a television receiver (TV) to receive terrestrial over-the-air (OTA) broadcast television signals from a television station. Terrestrial television is broadcast on frequencies from about 47 to 250  MHz in the very high frequency (VHF) band, and 470 to 960 MHz in the ultra high frequency (UHF) band in different countries.

Contents

Television antennas are manufactured in two different types: indoor and outdoor antennas. Indoor antennas are designed to be located on top of or next to the television set, but are ideally placed near a window in a room and as high up as possible for the best reception. [1] The most common types of indoor antennas are the dipole [2] ("rabbit ears"), which work best for VHF channels, and loop antennas, which work best for UHF. [3] Outdoor antennas on the other hand are designed to be mounted on a mast on top of the owner's house, [4] or in a loft or attic where the dry conditions and increased elevation are advantageous for reception and antenna longevity. Outdoor antennas are more expensive and difficult to install but are necessary for adequate reception in fringe areas far from television stations; the most common types of these are the Yagi, [2] log periodic, [2] and (for UHF) the multi-bay reflective array antenna.

Description

The purpose of the antenna is to intercept radio waves from the desired television stations and convert them to tiny radio frequency alternating currents which are applied to the television's tuner, which extracts the television signal. [5] The antenna is connected to the television with a specialized cable designed to carry radio current, called transmission line. Earlier antennas used a flat cable called 300 ohm twin-lead. The standard today is 75 ohm coaxial cable, which is less susceptible to interference which plugs into an F connector or Belling-Lee connector (depending on region) on the back of the TV. [6] To convert the signal from antennas that use a twin-lead line to the modern coaxial cable input, a small transformer called a balun is used in the line.

In most countries, television broadcasting is allowed in the very high frequency (VHF) band from 47 to 68 MHz, called VHF low band or band I in Europe; 174 to 216 MHz, called VHF high band or band III in Europe, and in the ultra high frequency (UHF) band from 470 to 698 MHz, called band IV and V in Europe. [7] The boundaries of each band vary somewhat in different countries. Radio waves in these bands travel by line-of-sight; they are blocked by hills and the visual horizon, limiting a television station's reception area to 65–95 km (40–60 miles), depending on terrain.

Analog vs. digital

In the previous standard analog television, used before 2006, the VHF and UHF bands required separate tuners in the television receiver, which had separate antenna inputs. The wavelength of a radio wave equals the speed of light (c), divided by the frequency. The above frequency bands cover a 15:1 wavelength ratio, or almost 4 octaves. It is difficult to design a single antenna to receive such a wide wavelength range, and there is an octave gap from 216 to 470 MHz between the VHF and UHF frequencies. So traditionally, separate antennas (outdoor antennas with separate sets of elements on a single support boom) have been used to receive the VHF and UHF channels. [6]

Starting in 2006, many countries in the world switched from broadcasting using an older analog television standard to newer digital television [8] (DTV). However, the same broadcast frequencies are generally used, so the antennas used for the older analog television will also receive the new DTV broadcasts. Sellers often claim to supply a special digital or high-definition television (HDTV) antenna advised as a replacement for an existing analog television antenna; at best this is misinformation to generate sales of unneeded equipment, [9] [10] At worst, it may leave the viewer with a UHF-only antenna in a local market (particularly in North America) where some digital stations remain on their original high VHF or low VHF frequencies.

Reception issues

West-German TV penetration in East Germany. West german tv penetration.svg
West-German TV penetration in East Germany.

Places unable to be reached by television broadcast transmitters are known as black spots in Australia. [11] In East Germany, the areas that could not receive western TV signals were referred to as the Tal der Ahnungslosen , or Valley of the Clueless.

Indoor

A loop antenna for UHF reception. This model also has two telescopic poles for VHF. It also has a mains-powered amplifier to improve signal strength. TV aerial by One For All.jpg
A loop antenna for UHF reception. This model also has two telescopic poles for VHF. It also has a mains-powered amplifier to improve signal strength.

Indoor antennas may be mounted on the television itself or stand on a table next to it, connected to the television by a short feed line. Due to space constraints, indoor antennas cannot be as large and elaborate as outdoor antennas, they are not mounted at as high an elevation, and the building walls block some of the radio waves; for these reasons, indoor antennas generally do not give as good reception as outdoor antennas. [6] They are often perfectly adequate in urban and suburban areas, which are usually within the strong radiation footprint of local television stations. Still, in rural fringe reception areas, only an outdoor antenna may give adequate reception. A few of the simplest indoor antennas are described below, but a great variety of designs and types exist. Many have a dial on the antenna with a number of different settings to alter the antenna's reception pattern. This should be rotated with the set on while looking at the screen until the best picture is obtained.

Rabbit ears

The 'rabbit ears' antenna with its coaxial plug Simple rabbit antenna.jpg
The 'rabbit ears' antenna with its coaxial plug

The oldest and most widely used (at least in the United States) indoor antenna is the rabbit ears or bunny ears, which are often provided with new television sets. [6] It is a simple half-wave dipole antenna used to receive the VHF television bands, consisting in the US of 54 to 88 MHz (band I) and 174 to 216 MHz (band III), with wavelengths of 5.5 to 1.4 m (18 to 5 feet). It is constructed of two telescoping rods attached to a base, which extend out to about 1 m (3.3 feet) length (approximately one-quarter wavelength at 54 MHz) and can be collapsed when not in use. For best reception, the rods should be adjusted to be a little less than ⁠1/4⁠ wavelength at the frequency of the television channel being received. However, the dipole has a wide bandwidth, so often adequate reception is achieved without adjusting the length.

The measured gain of rabbit ears is low, about ―2 dBi, or ―4 dB with respect to a half wave dipole. [6] This means it is not as directional and sensitive to distant stations as a large rooftop antenna. Still, its wide-angle reception pattern may allow it to receive several stations located in different directions without requiring readjustment when the channel is changed. Dipole antennas are bi-directional; that is, they have two main lobes in opposite directions, 180° apart. Instead of being fixed in position like other antennas, the elements are mounted on ball-and-socket joints. They can be adjusted to various angles in a V shape, allowing them to be moved out of the way in crowded quarters. Another reason for the V shape is that when receiving channels at the top of the band with the rods fully extended, the antenna elements will typically resonate at their 3rd harmonic. In this mode, the direction of maximum gain (the main lobe) is no longer perpendicular to the rods. Still, the radiation pattern will have lobes at an angle to the rods, making it advantageous to be able to adjust them to various angles.

Whip antenna

A 'whip' antenna at the side of a Casio portable TV Casio TV-770 portable television set-4660.jpg
A 'whip' antenna at the side of a Casio portable TV

Some portable televisions use a whip antenna. [6] This consists of a single telescoping rod about a meter (3.3 feet) long attached to the television, which can be retracted when not in use. It functions as a quarter-wave monopole antenna. The other side of the feedline is connected to the ground plane on the TV's circuit board, which acts as ground. The whip antenna generally has an omnidirectional reception pattern, with maximum sensitivity in directions perpendicular to the antenna axis and gain similar to rabbit ears.

Loop antenna

A simple wire loop antenna Simple loop antenna.jpg
A simple wire loop antenna

The UHF channels are often received by a single turn loop antenna. [6] Since a rabbit ears antenna only covers the VHF bands, it is often combined with a UHF loop mounted on the same base to cover all the TV channels. This of course also depends by country and region: for example in the UK and Ireland, terrestrial TV broadcasts are only on the UHF band, meaning that a loop antenna is necessary and the rabbit ears would only be useful for FM radio reception. [12] [13]

Flat antenna

A flat antenna Flat black antenna.png
A flat antenna

A more recent phenomenon for indoor antennas are flat antennas, which are lightweight, thin, and usually square-shaped with the claim of having more omnidirectional reception. They are also marketed as being more in line with modern minimalistic home designs. [14] Flat antennas may have a stand or could be hung on a wall or a window. [15] Internally, the thin, flat square is a loop antenna with its circular metallic wiring embedded into conductive plastic.[ citation needed ]

Outdoor

A Winegard 68 element VHF/UHF aerial antenna. This common multi-band antenna type uses a UHF Yagi at the front and a VHF log-periodic at the back coupled together. Aerial antenna.JPG
A Winegard 68 element VHF/UHF aerial antenna. This common multi-band antenna type uses a UHF Yagi at the front and a VHF log-periodic at the back coupled together.

When a higher-gain antenna is needed to achieve adequate reception in suburban or fringe reception areas, an outdoor directional antenna is usually used. Although most simple antennas have null directions where they have zero response, the directions of useful gain are very broad. In contrast, directional antennas can have an almost unidirectional radiation pattern, so the correct end of the antenna must be pointed at the TV station. As an antenna design provides higher gain (compared to a dipole), the main lobe of the radiation pattern becomes narrower. Outdoor antennas provide up to a 15 dB gain in signal strength and 15-20 dB greater rejection of ghost signals in analog TV. [6] Combined with a signal increase of 14 dB due to height and 11 dB due to lack of attenuating building walls, an outdoor antenna can result in a signal strength increase of up to 40 dB at the TV receiver. [6]

Outdoor antenna designs are often based on the Yagi–Uda antenna [16] or log-periodic dipole array (LPDA). [17] These are composed of multiple half-wave dipole elements, consisting of metal rods approximately half of the wavelength of the television signal, mounted in a line on a support boom. These act as resonators; the electric field of the incoming radio wave pushes the electrons in the rods back and forth, creating standing waves of oscillating voltage in the rods. The antenna can have a smaller or larger number of rod elements; in general, the more elements, the higher the gain and the more directional. Another design used mainly for UHF reception is the reflective array antenna, consisting of a vertical metal screen with multiple dipole elements mounted in front of it.

The television broadcast bands are too wide in frequency to be covered by a single antenna, so the two options are separate antennas used for the VHF and UHF bands or a combination (combo) VHF/UHF antenna. [6] A VHF/UHF antenna combines two antennas feeding the same feedline mounted on the same support boom. More extended elements that pick up VHF frequencies are located at the back of the boom and often function as a log-periodic antenna. Shorter elements that receive the UHF stations are located at the front of the boom and often function as a Yagi antenna.

Since directional antennas must be pointed at the transmitting antenna, this is a problem when the television stations to be received are located in different directions. In this case, two or more directional rooftop antennas, each pointed at a different transmitter, are often mounted on the same mast and connected to one receiver for best performance filter or matching circuits are used to keep each antenna from degrading the performance of the others connected to the same transmission line. An alternative is to use a single antenna mounted on a rotator, a remote servo system that rotates the antenna to a new direction when a dial next to the television is turned.

Sometimes television transmitters are deliberately located such that receivers in a given region need only receive transmissions in a relatively narrow band of the full UHF television spectrum and from the same direction, hence allowing the use of a higher gain grouped aerial. [18]

Installation

A short antenna pole next to a house Little aerial.jpg
A short antenna pole next to a house
Multiple Yagi TV aerials Antenna.jpg
Multiple Yagi TV aerials

Antennas are commonly placed on rooftops and sometimes in attics. Placing an antenna indoors significantly attenuates the level of the available signal. [19] [20] Directional antennas must be pointed at the transmitter they are receiving; in most cases great accuracy is not needed. In a given region, it is sometimes arranged that all television transmitters are located in roughly the same direction and use frequencies spaced closely enough that a single antenna suffices for all. A single transmitter location may transmit signals for several channels. [21] CABD (communal antenna broadcast distribution) is a system installed inside a building to receive free-to-air TV/FM signals transmitted via radio frequencies and distribute them to the audience. [22]

Analog television signals are susceptible to ghosting in the image, multiple closely spaced images giving the impression of blurred and repeated images of edges in the picture. This is due to the signal being reflected from nearby objects (buildings, trees, mountains); several copies of the signal, of different strengths and subject to different delays, are picked up. This is different for other transmissions. Careful positioning of the antenna can produce a compromise position, which minimizes the ghosts on different channels. Ghosting is also possible if multiple antennas connected to the same receiver pick up the same station, especially if the lengths of the cables connecting them to the splitter/merger are different lengths or the antennas are too close together. [23] Analog television is being replaced by digital, which is not subject to ghosting; the same reflected signal that causes ghosting in an analog signal would produce no viewable content at all in digital. However, in this case, interference causes significantly more significant image quality degradation.

Rooftop and other outdoor antennas

Aerials mounted on the rooftops of houses in England Sixteen chimneys, I wouldn't like to have been a scullery maid in the old days.jpg
Aerials mounted on the rooftops of houses in England

Aerials are attached to roofs in various ways, usually on a pole to elevate it above the roof. This is generally sufficient in most areas. In some places, however, such as a deep valley or near taller structures, the antenna may need to be placed significantly higher, using a guyed mast or mast. The wire connecting the antenna indoors is referred to as the downlead or drop , and the longer the downlead is, the greater the signal degradation in the wire. Certain cables may help reduce this tendency.

The higher the antenna is placed, the better it will perform. An antenna of higher gain will be able to receive weaker signals from its preferred direction. Intervening buildings, topographical features (mountains), and dense forests will weaken the signal; in many cases, the signal will be reflected such that a usable signal is still available. There are physical dangers inherent to high or complex antennas, such as the structure falling or being destroyed by weather. There are also varying local ordinances which restrict and limit such things as the height of a structure without obtaining permits. For example, in the United States, the Telecommunications Act of 1996 allows any homeowner to install "An antenna that is designed to receive local television broadcast signals" but that "masts higher than 12 feet [3.5 m] above the roof-line may be subject to local permitting requirements." [24]

Indoor antennas

As discussed previously, antennas may be placed indoors where signals are strong enough to overcome antenna shortcomings. The antenna is simply plugged into the television receiver and placed conveniently, often on the top of the receiver ("set-top"). Sometimes, the position needs to be experimented with to get the best picture. Indoor antennas can also benefit from RF amplification, commonly called a TV booster. Reception from indoor antennas can be problematic in weak signal areas.[ citation needed ]

Attic installation

Sometimes, it is desirable not to put an antenna on the roof; in these cases, antennas designed for outdoor use are often mounted in the attic or loft, although antennas designed for attic use are also available. Putting an antenna indoors significantly decreases its performance due to lower elevation above ground level and intervening walls; however, in strong signal areas, reception may be satisfactory. [20] One layer of asphalt shingles, roof felt, and a plywood roof deck is considered to attenuate the signal to about half. [25]

Multiple antennas, rotators

Two aerials set up on a roof. Spaced horizontally and vertically Multiple Antenna.JPG
Two aerials set up on a roof. Spaced horizontally and vertically

It is sometimes desired to receive signals from transmitters which are not in the same direction. This can be achieved, for one station at a time, by using a rotator operated by an electric motor to turn the antenna as desired. Alternatively, two or more antennas, each pointing at a desired transmitter and coupled by appropriate circuitry, can be used. To prevent the antennas from interfering with each other, the vertical spacing between the booms must be at least half the wavelength of the lowest frequency to be received (Distance = ⁠ λ /2⁠). [23] The wavelength of 54 MHz (Channel 2) is 5.5 m (18 feet) (λ × f = c) so the antennas must be a minimum of 2.25 m (90 inches) apart. It is also important that the cables connecting the antennas to the signal splitter/merger be precisely the same length to prevent phasing issues, which cause ghosting with analog reception. That is, the antennas might both pick up the same station; the signal from the one with the shorter cable will reach the receiver slightly sooner, supplying the receiver with two pictures slightly offset. There may be phasing issues even with the same length of down-lead cable. Band-pass filters or signal traps may help to reduce this problem.

For side-by-side placement of multiple antennas, as is common in a space of limited height such as an attic, they should be separated by at least one full wavelength of the lowest frequency to be received at their closest point.

When multiple antennas are often used, one is for a range of co-located stations, and the other is for a single transmitter in a different direction.

Safety

See also

Related Research Articles

<span class="mw-page-title-main">Cable television</span> Television content transmitted via signals on coaxial cable

Cable television is a system of delivering television programming to consumers via radio frequency (RF) signals transmitted through coaxial cables, or in more recent systems, light pulses through fibre-optic cables. This contrasts with broadcast television, in which the television signal is transmitted over-the-air by radio waves and received by a television antenna, or satellite television, in which the television signal is transmitted over-the-air by radio waves from a communications satellite and received by a satellite dish on the roof. FM radio programming, high-speed Internet, telephone services, and similar non-television services may also be provided through these cables. Analog television was standard in the 20th century, but since the 2000s, cable systems have been upgraded to digital cable operation.

<span class="mw-page-title-main">Very high frequency</span> Electromagnetic wave range of 30-300 MHz

Very high frequency (VHF) is the ITU designation for the range of radio frequency electromagnetic waves from 30 to 300 megahertz (MHz), with corresponding wavelengths of ten meters to one meter. Frequencies immediately below VHF are denoted high frequency (HF), and the next higher frequencies are known as ultra high frequency (UHF).

<span class="mw-page-title-main">Medium wave</span> Radio transmission using wavelengths 200-1000 m

Medium wave (MW) is a part of the medium frequency (MF) radio band used mainly for AM radio broadcasting. The spectrum provides about 120 channels with more limited sound quality than FM stations on the FM broadcast band. During the daytime, reception is usually limited to more local stations, though this is dependent on the signal conditions and quality of radio receiver used. Improved signal propagation at night allows the reception of much longer distance signals. This can cause increased interference because on most channels multiple transmitters operate simultaneously worldwide. In addition, amplitude modulation (AM) is often more prone to interference by various electronic devices, especially power supplies and computers. Strong transmitters cover larger areas than on the FM broadcast band but require more energy and longer antennas. Digital modes are possible but have not reached momentum yet.

<span class="mw-page-title-main">Ultra high frequency</span> Electromagnetic spectrum 300–3000 MHz

Ultra high frequency (UHF) is the ITU designation for radio frequencies in the range between 300 megahertz (MHz) and 3 gigahertz (GHz), also known as the decimetre band as the wavelengths range from one meter to one tenth of a meter. Radio waves with frequencies above the UHF band fall into the super-high frequency (SHF) or microwave frequency range. Lower frequency signals fall into the VHF or lower bands. UHF radio waves propagate mainly by line of sight; they are blocked by hills and large buildings although the transmission through building walls is strong enough for indoor reception. They are used for television broadcasting, cell phones, satellite communication including GPS, personal radio services including Wi-Fi and Bluetooth, walkie-talkies, cordless phones, satellite phones, and numerous other applications.

<span class="mw-page-title-main">Medium frequency</span> The range 300-3000 kHz of the electromagnetic spectrum

Medium frequency (MF) is the ITU designation for radio frequencies (RF) in the range of 300 kilohertz (kHz) to 3 megahertz (MHz). Part of this band is the medium wave (MW) AM broadcast band. The MF band is also known as the hectometer band as the wavelengths range from ten to one hectometers. Frequencies immediately below MF are denoted as low frequency (LF), while the first band of higher frequencies is known as high frequency (HF). MF is mostly used for AM radio broadcasting, navigational radio beacons, maritime ship-to-shore communication, and transoceanic air traffic control.

<span class="mw-page-title-main">Antenna (radio)</span> Electrical device

In radio engineering, an antenna or aerial is an electronic device that converts an alternating electric current into radio waves (transmitting), or radio waves into an electric current (receiving). It is the interface between radio waves propagating through space and electric currents moving in metal conductors, used with a transmitter or receiver. In transmission, a radio transmitter supplies an electric current to the antenna's terminals, and the antenna radiates the energy from the current as electromagnetic waves. In reception, an antenna intercepts some of the power of a radio wave in order to produce an electric current at its terminals, that is applied to a receiver to be amplified. Antennas are essential components of all radio equipment.

<span class="mw-page-title-main">Terrestrial television</span> Television content transmitted via signals in the air

Terrestrial television, or over-the-air television (OTA) is a type of television broadcasting in which the content is transmitted via radio waves from the terrestrial (Earth-based) transmitter of a TV station to a TV receiver having an antenna. The term terrestrial is more common in Europe and Latin America, while in Canada and the United States it is called over-the-air or simply broadcast. This type of TV broadcast is distinguished from newer technologies, such as satellite television, in which the signal is transmitted to the receiver from an overhead satellite; cable television, in which the signal is carried to the receiver through a cable; and Internet Protocol television, in which the signal is received over an Internet stream or on a network utilizing the Internet Protocol. Terrestrial television stations broadcast on television channels with frequencies between about 52 and 600 MHz in the VHF and UHF bands. Since radio waves in these bands travel by line of sight, reception is generally limited by the visual horizon to distances of 64–97 kilometres, although under better conditions and with tropospheric ducting, signals can sometimes be received hundreds of kilometers distant.

<span class="mw-page-title-main">TV and FM DX</span> Long-distance reception of signals on the VHF frequency band

TV DX and FM DX is the active search for distant radio or television stations received during unusual atmospheric conditions. The term DX is an old telegraphic term meaning "long distance."

<span class="mw-page-title-main">Diplexer</span>

A diplexer is a passive device that implements frequency-domain multiplexing. Two ports are multiplexed onto a third port. The signals on ports L and H occupy disjoint frequency bands. Consequently, the signals on L and H can coexist on port S without interfering with each other.

A broadcast transmitter is an electronic device which radiates radio waves modulated with information content intended to be received by the general public. Examples are a radio broadcasting transmitter which transmits audio (sound) to broadcast radio receivers (radios) owned by the public, or a television transmitter, which transmits moving images (video) to television receivers (televisions). The term often includes the antenna which radiates the radio waves, and the building and facilities associated with the transmitter. A broadcasting station consists of a broadcast transmitter along with the production studio which originates the broadcasts. Broadcast transmitters must be licensed by governments, and are restricted to specific frequencies and power levels. Each transmitter is assigned a unique identifier consisting of a string of letters and numbers called a callsign, which must be used in all broadcasts.

The Llanddona transmitting station is a broadcasting and telecommunications facility, situated at Llanddona, near Beaumaris, on the isle of Anglesey, Wales. It comprises a 106.7 metres (350 ft) guyed mast with antennas attached at various heights. It is owned and operated by Arqiva.

<span class="mw-page-title-main">Wenvoe transmitting station</span> Transmission station in Wales

The Wenvoe transmitting station, officially known as Arqiva Wenvoe, is the main facility for broadcasting and telecommunications for South Wales and the West Country. It is situated close to the village of Wenvoe in the Vale of Glamorgan, Wales, in the UK.

A digital channel election was the process by which television stations in the United States chose which physical radio-frequency TV channel they would permanently use after the analog shutdown in 2009. The process was managed and mandated by the Federal Communications Commission for all full-power TV stations. Low-powered television (LPTV) stations are going through a somewhat different process, and are also allowed to flash-cut to digital.

<span class="mw-page-title-main">Preseli transmitting station</span>

The Preseli transmitting station is a broadcasting and telecommunications facility on the eastern end of the Preseli Mountains, close to the villages of Crymych and Pentre Galar in Pembrokeshire, Wales. It is owned and operated by Arqiva.

The Oxford transmitting station is a broadcasting and telecommunications facility, situated on land 129.5 metres (425 ft) above Ordnance Datum to the north east of the city of Oxford, in Oxfordshire, England. It has a guyed steel lattice mast which is 154.4 metres (507 ft) in height to the top of the main steel structure. The UHF television antenna, which consist of a vertical array of transmitting panels, is mounted above the steel structure. The total height of the mast to the top of this UHF antenna is 165.7 metres (544 ft). It is owned and operated by Arqiva.

<span class="mw-page-title-main">Radio</span> Use of radio waves to carry information

Radio is the technology of communicating using radio waves. Radio waves are electromagnetic waves of frequency between 3 hertz (Hz) and 300 gigahertz (GHz). They are generated by an electronic device called a transmitter connected to an antenna which radiates oscillating electrical energy, often characterized as a wave. They can be received by other antennas connected to a radio receiver; this is the fundamental principle of radio communication. In addition to communication, radio is used for radar, radio navigation, remote control, remote sensing, and other applications.

<span class="mw-page-title-main">Antenna amplifier</span>

In electronics, an antenna amplifier is a device that amplifies an antenna signal, usually into an output with the same impedance as the input impedance. Typically 75 ohm for coaxial cable and 300 ohm for twin-lead cable.

In broadcasting, a transposer or translator is a device in or beyond the service area of a radio or television station transmitter that rebroadcasts signals to receivers which can’t properly receive the signals of the transmitter because of a physical obstruction. A translator receives the signals of the transmitter and rebroadcasts the signals to the area of poor reception. Sometimes the translator is also called a relay transmitter, rebroadcast transmitter or transposer. Since translators are used to cover a small shadowed area, their output powers are usually lower than that of the radio or television station transmitters feeding them.

<span class="mw-page-title-main">UHF television broadcasting</span> Ultra high frequency radio to transmit TV

UHF television broadcasting is the use of ultra high frequency (UHF) radio for over-the-air transmission of television signals. UHF frequencies are used for both analog and digital television broadcasts. UHF channels are typically given higher channel numbers, like the US arrangement with VHF channels (initially) 1 to 13, and UHF channels (initially) numbered 14 to 83. Compared with an equivalent VHF television transmitter, to cover the same geographic area with a UHF transmitter requires a higher effective radiated power, implying a more powerful transmitter or a more complex antenna. However, the additional channels allow more broadcasters in a given region without causing objectionable mutual interference.

In radio systems, many different antenna types are used whose properties are especially crafted for particular applications.

References

  1. ↑ "Tips & Tricks Aerials". One For All. Retrieved 2024-07-04.
  2. 1 2 3 Gulati, R.R. (2007). Monochrome And Colour Television. New Age International. pp. 164–170. ISBN   978-8122416077. Archived from the original on 2023-07-01. Retrieved 2021-10-16.
  3. ↑ Davis, Clint (2022-03-22). "Rabbit ears vs. flat antennas: Which one is best for my needs?". The Free TV Project. Retrieved 2024-07-04.
  4. ↑ Johnson 1993 Antenna Engineering Handbook, 3rd Ed. Archived 2023-07-01 at the Wayback Machine , p. 29.5-29.6
  5. ↑ Joy, Edward B. TV Receiving Antennas in Johnson, Richard C. (1993). Antenna Engineering Handbook, 3rd Ed. McGraw-Hill, Inc. pp. Chapter 29. ISBN   9780070323810. Archived from the original on 2023-07-01. Retrieved 2022-03-31.
  6. 1 2 3 4 5 6 7 8 9 10 Johnson 1993 Antenna Engineering Handbook, 3rd Ed. , p. 29.6. Archived 2023-07-01 at the Wayback Machine .
  7. ↑ Johnson 1993 Antenna Engineering Handbook, 3rd Ed. , p. 29.2. Archived 2023-07-01 at the Wayback Machine .
  8. ↑ Teimouri, M.H.; Ghobadi, Ch.; Nourinia, J.; Kaboutari, Keivan; Shokri, Majid; Virdee, B.S. (2022). "Broadband printed dipole antenna with integrated balun and tuning element for DTV application". AEU - International Journal of Electronics and Communications. 148: 154161. doi:10.1016/j.aeue.2022.154161. S2CID   247126109.
  9. ↑ "TV Antenna Range". www.dennysantennaservice.com. Archived from the original on 2021-05-11. Retrieved 2009-11-10.
  10. ↑ BBC: Digital switch advice 'shocking' Archived 2017-09-05 at the Wayback Machine October 13, 2008, 9 of 14 installers gave bad or misleading advice, suggesting that people are likely to need a new aerial for digital switchover ... 5 told the mystery shopper they would need a "digital aerial", when in fact there is no such thing.
  11. ↑ "Going digital: tracing the transition to digital terrestrial television in Australia digital". Parliament of Australia. 12 June 2011. Archived from the original on 6 August 2021. Retrieved 6 August 2021.
  12. ↑ Macfarlane, Andrew (2024-02-06). "Understanding TV Aerial Frequencies and Channels in the UK". Counteract – Music | News | Food | Travel. Retrieved 2024-07-04.
  13. ↑ "RTÉNL - Frequently Asked Questions" (PDF). 2rn.ie.
  14. ↑ "Frustrated After Trying to Stream the Super Bowl? Get This Antenna for Next Year". WSJ Buyside. 2024-02-12. Retrieved 2024-07-04.
  15. ↑ Goren, Or (2024-01-04). "Best Indoor TV Aerial For Freeview In 2024". Cord Busters. Retrieved 2024-07-04.
  16. ↑ Johnson 1993 Antenna Engineering Handbook, 3rd Ed. Archived 2023-07-01 at the Wayback Machine , p. 29.16-29.21
  17. ↑ Johnson 1993 Antenna Engineering Handbook, 3rd Ed. Archived 2023-07-01 at the Wayback Machine , p. 29.14-29.16
  18. ↑ UK aerial groups Archived 2019-12-19 at the Wayback Machine In the UK transmitters are grouped into A, B, C, D, E, and K frequency bands and located so that, as far as possible, they are all in the same direction for receivers in a given region. This allows optimal reception of all stations by a single fixed narrow-band (and hence high-gain) antenna pointing in a fixed direction.
  19. ↑ "Rob's TV Digital Aerial installations". Archived from the original on 2011-03-04. Retrieved 2011-03-20.
  20. 1 2 "Attic Mounted TV Antennas - Stallions Satellite and Antenna". tvantenna.com. Archived from the original on 2009-12-13. Retrieved 2009-12-19.
  21. ↑ "UK TV Transmitters". www.aerialsandtv.com. Archived from the original on 2019-12-19. Retrieved 2019-12-21.
  22. ↑ "Digital TV". www.digitaltv.gov.hk. Archived from the original on 2016-03-04. Retrieved 2015-10-17.
  23. 1 2 "Combining or Stacking Two TV Antennas - Stallions Satellite and Antenna". tvantenna.com. Archived from the original on 2009-11-24. Retrieved 2009-11-11.
  24. ↑ "Over-the-Air Reception Devices Rule". Federal Communications Commission. December 9, 2015. Archived from the original on January 8, 2017. Retrieved January 7, 2017.
  25. ↑ "Antennas Direct - FAQs About HD Television Antennas". www.terrestrial-digital.com. Archived from the original on 2009-03-29. Retrieved 2009-12-19.
  26. ↑ "Lightning Protection for TV and Radio Antennas". nojolt.com. Archived from the original on 2010-03-30. Retrieved 2009-12-19.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.