A coal-seam fire is a burning of an outcrop or underground coal seam. Most coal-seam fires exhibit smouldering combustion, [1] particularly underground coal-seam fires, because of limited atmospheric oxygen availability. Coal-seam fire instances on Earth date back several million years. [2] [3] Due to thermal insulation and the avoidance of rain/snow extinguishment by the crust, underground coal-seam fires are the most persistent fires on Earth and can burn for thousands of years, like Burning Mountain in Australia. [4] Coal-seam fires can be ignited by self-heating of low-temperature oxidation, lightning, wildfires and even arson. Coal-seam fires have been slowly shaping the lithosphere and changing atmosphere, but this pace has become faster and more extensive in modern times, triggered by mining. [5]
Coal fires are a serious health and safety hazard, affecting the environment by releasing toxic fumes; reigniting grass, brush, or forest fires; and causing subsidence of surface infrastructure such as roads, railways, pipelines, electric lines, bridge supports, buildings, and homes. Whether started by humans or by natural causes, coal-seam fires continue to burn for decades, centuries, or even millennia, until one of the following occurs: either the fuel source is exhausted, a permanent groundwater table is encountered, the depth of the burn becomes greater than the ground's capacity to subside and vent, or humans intervene. Because they burn underground, coal-seam fires are extremely difficult and costly to extinguish, and are unlikely to be suppressed by rainfall. [6] There are strong similarities between coal fires and peat fires.
Across the world, thousands of underground coal fires are burning at any given moment. The problem is most acute in industrializing, coal-rich nations such as China. [5] Global coal fire emissions are estimated to cause 40 tons of mercury to enter the atmosphere annually, and to represent three percent of the world's annual CO2 emissions. [7]
Coal-seam fires can be divided into near-surface fires, in which seams extend to the surface and the oxygen required for their ignition comes from the atmosphere, and fires in deep underground mines, where the oxygen comes from ventilation.
Mine fires may begin as a result of an industrial accident, generally involving a gas explosion. Historically, some mine fires were started when bootleg mining was stopped by authorities, usually by blowing the mine up. Many recent mine fires have started from people burning trash in a landfill that was in proximity to abandoned coal mines, including the much-publicized Centralia, Pennsylvania, fire, which has been burning since 1962. Of the hundreds of mine fires in the United States burning today, most are found in the state of Pennsylvania.
Some fires along coal seams are natural occurrences. Some coals may self-ignite at temperatures as low as 40 °C (104 °F) for brown coal in the right conditions of moisture and grain size. [8] The fire usually begins a foot or two inside the coal at a depth in which the permeability of the coal allows the inflow of air but in which the ventilation does not remove the heat which is generated. Self-ignition was a recognised problem in steamship times. One well known source of fires is mining breaking into a high pressure cavity of methane gas which on release can generate a spark of static electricity to ignite the gas and start a coal explosion and fire. The same gas static is well known in ships and care has to be taken to ensure no such static sparking can occur.
Two basic factors determine whether spontaneous combustion occurs or not, the ambient temperature and the grain size:
Wildfires (lightning-caused or others) can ignite the coal close to the surface or the entrance of a mine, and the smouldering fire can spread through the seam, creating subsidence that may open further seams to oxygen and spawn future wildfires when the fire breaks to the surface. Prehistoric clinker outcrops in the American West are the result of prehistoric coal fires that left a residue that resists erosion better than the matrix, leaving buttes and mesa. It is estimated that Australia's Burning Mountain, the oldest known coal fire, has burned for 6,000 years. [9]
Globally, thousands of inextinguishable mine fires are burning, especially in China where poverty, lack of government regulations and runaway development combine to create an environmental disaster. Modern strip mining exposes smouldering coal seams to the air, revitalizing the flames.
Rural Chinese in coal-bearing regions often dig coal for household use, abandoning the pits when they become too deep, leaving highly combustible coal dust exposed to the air. Using satellite imagery to map China's coal fires resulted in the discovery of many previously unknown fires. The oldest coal fire in China is in Baijigou (白芨沟, in Dawukou District of Shizuishan, Ningxia) and is said to have been burning since the Qing Dynasty (before 1912). [10]
Before attempting to extinguish a near-surface coal-seam fire, its location and underground extent should be determined as precisely as possible. Besides studying the geographic, geologic and infrastructural context, information can be gained from direct measurements. These include:
Underground coal mines can be equipped with permanently installed sensor systems. These relay pressure, temperature, airflow and gas composition measurements to the safety monitoring personnel, giving them early warning of any problems.
Besides destruction of the affected areas, coal fires often emit toxic gases, including carbon monoxide and sulphur dioxide. China's coal fires, which consume an estimated 20 – 200 million tons of coal a year, make up as much as 1 percent of the global carbon dioxide emissions from fossil fuels. [9]
One of the most visible changes will be subsidence. Another local environmental effect can include the presence of plants or animals that are aided by the coal fire. The prevalence of non-native plants can depend upon the fire's duration and the size of the affected area. For example, near a coal fire in Germany, many Mediterranean insects and spiders were identified in a region with cold winters, and it is believed that elevated ground temperatures above the fires permitted their survival. [14]
In order to thrive, a fire requires fuel, oxygen, and heat. As underground fires are very difficult to reach directly, fire fighting involves finding an appropriate methodology which addresses the interaction of fuel and oxygen for the specific fire in question. A fire can be isolated from its fuel source, for example through firebreaks or fireproof barriers. Many fires, particularly those on steep slopes, can be completely excavated. In the case of near-surface coal-seam fires, the influx of oxygen in the air can be interrupted by covering the area or installing gas-tight barriers. Another possibility is to hinder the outflow of combustion gases so that the fire is quenched by its own exhaust fumes. Energy can be removed by cooling, usually by injecting large amounts of water. However, if any remaining dry coal absorbs water, the resulting heat of absorption can lead to re-ignition of a once-quenched fire as the area dries. Accordingly, more energy must be removed than the fire generates. In practice these methods are combined, and each case depends on the resources available. This is especially true for water, for example in arid regions, and for covering material, such as loess or clay, to prevent contact with the atmosphere.
Extinguishing underground coal fires, which sometimes exceed temperatures of 540 °C (1,000 °F), is both highly dangerous and very expensive. [9]
Near-surface coal-seam fires are routinely extinguished in China following a standard method basically consisting of the following phases:
Efforts are underway to refine this method, for example with additives to the quenching water or with alternative extinguishing agents.
Underground coal-seam fires are customarily quenched by inertisation through mine rescue personnel. Toward this end the affected area is isolated by dam constructions in the galleries. Then an inert gas, usually nitrogen, is introduced, usually making use of available pipelines.
In 2004, the Chinese government claimed success in extinguishing a mine fire at a colliery near Urumqi in China's Xinjiang province that had been burning since 1874. However, a March 2008 Time magazine article quotes researcher Steven Q. Andrews as saying, "I decided to go to see how it was extinguished, and flames were visible and the entire thing was still burning. ... They said it was put out, and who is to say otherwise?" [15]
A jet engine unit, known as Gorniczy Agregat Gasniczy (GAG), was developed in Poland and successfully used for fighting coal fires and displacing firedamp in mines.
Time magazine reported in July 2010 that less expensive alternatives for extinguishing coal-seam fires were beginning to reach the market, including heat-resistant grouts and a fire-smothering nitrogen foam, with other innovative solutions on the way. [7]
Some of the more notable mine fires around the world are listed below.
In China, the world's largest coal producer with an annual output around 2.5 billion tons, coal fires are a serious problem. It has been estimated that some 10–200 million tons of coal uselessly burn annually, and that the same amount again is made inaccessible to mining. [10] Coal fires extend over a belt across the entire north China, whereby over one hundred major fire areas are listed, each of which contains many individual fire zones. They are concentrated in the provinces of Xinjiang, Inner Mongolia and Ningxia. Beside losses from burned and inaccessible coal, these fires contribute to air pollution and considerably increased levels of greenhouse gas emissions and have thereby become a problem which has gained international attention.
In Saint-Etienne coal basin, five burning hills (montagnes de feu) have been described from the early 17th Century to the early 19th century around the city of Saint-Etienne. [23] [24] Some of these fires were reported burning for 3 centuries. Most of them were extinguished in 1785 [25] These old burning hills correspond today to the Mont Salson, Bois d'Avaize and Cote Chaude in Saint-Etienne, la colline du Brûlé in la Ricamarie and Le mont du Feu (Mount of fire) in Genilac. The fire in Genilac lasted 30 years from 1740. [24] Outcrops of pyrometamorphic rocks generated by these fires are visible today on Mont Salson and bois d'Avaize.
In Planitz, now a part of the city of Zwickau, a coal seam that had been burning since 1476 was only quenched in 1860. [26] [27] In Dudweiler, Saarland, a coal-seam fire ignited around 1668 and is still burning. [28] This so-called Burning Mountain (" Brennender Berg ") soon became a tourist attraction and was even visited by Johann Wolfgang von Goethe. [29] Also well-known is the so-called Stinksteinwand (stinking stone wall) in Schwalbenthal on the eastern slope of the Hoher Meißner, where several seams caught fire centuries ago after lignite coal mining ceased; combustion gas continues to reach the surface. [30]
In India, as of 2010, 68 fires were burning beneath a 58-square-mile (150 km2) region of the Jharia coalfield in Dhanbad, Jharkhand. Mine fires started in this region in 1916 and are rapidly destroying the only source of prime coking coal in the country as well as the surrounding areas due to land subsidence and pollution. [31]
Coal and peat fires in Indonesia are often ignited by forest fires near deposits at the surface. It is difficult to determine when a forest fire is started by a coal-seam fire, or vice versa. [6] The most common cause of forest fires and haze in Indonesia is intentional burning of forest to clear land for plantation crops of pulp wood, rubber and palm oil.
No accurate count of coal-seam fires has been completed in Indonesia. Only a minuscule fraction of the country has been surveyed for coal fires. [6] The best data available come from a study based on systematic, on-the-ground observation. In 1998, a total of 125 coal fires were located and mapped within a 2-kilometre strip either side of a 100-kilometre stretch of road north of Balikpapan to Samarinda in East Kalimantan, using hand-held Global Positioning System (GPS) equipment. Extrapolating this data to areas on Borneo and Sumatra underlain by known coal deposits, it was estimated that more than 250,000 coal-seam fires may have been burning in Indonesia in 1998. [12]
Land clearing practices which use fire, often starting forest fires, may be the cause of coal-seam fires in Indonesia. In 1982 and 1983 one of the largest forest fires in this century raged for several months through an estimated 5 million hectares of Borneo's tropical rainforests. Goldammer and Seibert however concluded that there are indications that coal-seam fires already occurred between 13,200 and 15,000 BP. [32]
A fire season usually occurs every 3 to 5 years, when the climate in parts of Indonesia becomes exceptionally dry from June to November due to the El Niño–Southern Oscillation off the west coast of South America. Since 1982, fire has been a recurring feature on the islands of Borneo and Sumatra, burning large areas in 1987, 1991, 1994, 1997–1998, 2001 and 2004. [12]
In October 2004 smoke from land clearing again covered substantial portions of Borneo and Sumatra, disrupting air travel, [33] increasing hospital admissions, [34] and extending to portions of Brunei, Singapore and Malaysia. [35] Coal outcrops are so common in Indonesia it is virtually certain these fires ignited new coal-seam fires.
In 1944, Longyearbyen Mine #2 on Svalbard was set alight by sailors from the German battleship Tirpitz on its final sortie outside of Norwegian coastal waters. The mine continued to burn for 20 years, while some of the areas were subsequently mined from the reconstructed Mine #2b.
Many coalfields in the US are subject to spontaneous ignition. The federal Office of Surface Mining (OSM) maintains a database (AMLIS), which in 1999 listed 150 fire zones. In mid-2010, according to OSM, more than 100 fires were burning beneath nine states, most of them in Colorado, Kentucky, Pennsylvania, Utah and West Virginia. Some geologists say that many fires go unreported, so that the actual number of them may be nearer to 200, across 21 states. [7]
In Pennsylvania, 45 fire zones are known, the most famous being the Centralia mine fire in the Centralia mine in the hard coal region of Columbia County, which has been burning since 1962. [7] Burning Mine, near Summit Hill, caught fire in 1859. [38]
In Colorado, coal fires have arisen as a consequence of fluctuations in the groundwater level, which can increase the temperature of the coal up to 300 °C, enough to cause it to spontaneously ignite.[ citation needed ]
The Powder River Basin in Wyoming and Montana contains some 800 billion tons of brown coal, and the Lewis and Clark Expedition (1804 to 1806) reported fires there. Fires have been a natural occurrence in this area for about three million years and have shaped the landscape. For example, an area about 4,000 square kilometres in size is covered with coal clinker, some of it in Theodore Roosevelt National Park, where there is a spectacular view of fiery red coal clinker from Scoria Point. [39]
The novel Germinal by the French novelist Emile Zola describes a fictional coal fire called Le Tartaret .
The 1991 film Nothing but Trouble , directed and co-written by Dan Aykroyd, features a town, Valkenvania, that has an underground coal fire that has been burning for decades. The judge of the town references the constantly burning coal-mine fire as the source of his hatred of financiers.
In the TV show Scorpion , Season 3, Episode 23, the Scorpion team extinguishes an underground coal fire in Wyoming.
Coal is a combustible black or brownish-black sedimentary rock, formed as rock strata called coal seams. Coal is mostly carbon with variable amounts of other elements, chiefly hydrogen, sulfur, oxygen, and nitrogen. Coal is a type of fossil fuel, formed when dead plant matter decays into peat which is converted into coal by the heat and pressure of deep burial over millions of years. Vast deposits of coal originate in former wetlands called coal forests that covered much of the Earth's tropical land areas during the late Carboniferous (Pennsylvanian) and Permian times.
Fire is the rapid oxidation of a material in the exothermic chemical process of combustion, releasing heat, light, and various reaction products. At a certain point in the combustion reaction, called the ignition point, flames are produced. The flame is the visible portion of the fire. Flames consist primarily of carbon dioxide, water vapor, oxygen and nitrogen. If hot enough, the gases may become ionized to produce plasma. Depending on the substances alight, and any impurities outside, the color of the flame and the fire's intensity will be different.
Lignite, often referred to as brown coal, is a soft, brown, combustible sedimentary rock formed from naturally compressed peat. It has a carbon content around 25–35% and is considered the lowest rank of coal due to its relatively low heat content. When removed from the ground, it contains a very high amount of moisture, which partially explains its low carbon content. Lignite is mined all around the world and is used almost exclusively as a fuel for steam-electric power generation.
Thermite is a pyrotechnic composition of metal powder and metal oxide. When ignited by heat or chemical reaction, thermite undergoes an exothermic reduction-oxidation (redox) reaction. Most varieties are not explosive, but can create brief bursts of heat and high temperature in a small area. Its form of action is similar to that of other fuel-oxidizer mixtures, such as black powder.
Coke is a grey, hard, and porous coal-based fuel with a high carbon content. It is made by heating coal or oil in the absence of air. Coke is an important industrial product, used mainly in iron ore smelting, but also as a fuel in stoves and forges.
Bituminous coal, or black coal, is a type of coal containing a tar-like substance called bitumen or asphalt. Its coloration can be black or sometimes dark brown; often there are well-defined bands of bright and dull material within the seams. It is typically hard but friable. Its quality is ranked higher than lignite and sub-bituminous coal, but lesser than anthracite. It is the most abundant rank of coal, with deposits found around the world, often in rocks of Carboniferous age. Bituminous coal is formed from sub-bituminous coal that is buried deeply enough to be heated to 85 °C (185 °F) or higher.
Anthracite, also known as hard coal and black coal, is a hard, compact variety of coal that has a submetallic lustre. It has the highest carbon content, the fewest impurities, and the highest energy density of all types of coal and is the highest ranking of coals.
Coal mining is the process of extracting coal from the ground or from a mine. Coal is valued for its energy content and since the 1880s has been widely used to generate electricity. Steel and cement industries use coal as a fuel for extraction of iron from iron ore and for cement production. In the United Kingdom and South Africa, a coal mine and its structures are a colliery, a coal mine is called a "pit", and above-ground mining structures are referred to as a "pit head". In Australia, "colliery" generally refers to an underground coal mine.
Firedamp is any flammable gas found in coal mines, typically coalbed methane. It is particularly found in areas where the coal is bituminous. The gas accumulates in pockets in the coal and adjacent strata and when they are penetrated the release can trigger explosions. Historically, if such a pocket was highly pressurized, it was termed a "bag of foulness".
Coalbed methane, coalbed gas, or coal seam gas (CSG) is a form of natural gas extracted from coal beds. In recent decades it has become an important source of energy in United States, Canada, Australia, and other countries.
Underground coal gasification (UCG) is an industrial process which converts coal into product gas. UCG is an in-situ gasification process, carried out in non-mined coal seams using injection of oxidants and steam. The product gas is brought to the surface through production wells drilled from the surface.
Smouldering or smoldering is the slow, flameless form of combustion, sustained by the heat evolved when oxygen directly attacks the surface of a condensed-phase fuel. Many solid materials can sustain a smouldering reaction, including coal, cellulose, wood, cotton, tobacco, cannabis, peat, plant litter, humus, synthetic foams, charring polymers including polyurethane foam and some types of dust. Common examples of smouldering phenomena are the initiation of residential fires on upholstered furniture by weak heat sources, and the persistent combustion of biomass behind the flaming front of wildfires.
Coal is mined in every state of Australia. The largest black coal resources occur in Queensland and New South Wales. About 70% of coal mined in Australia is exported, mostly to eastern Asia, and of the balance most is used in electricity generation. In 2019-20 Australia exported 390 Mt of coal and was the world's largest exporter of metallurgical coal and second largest exporter of thermal coal. While only employing 50,000 mining jobs nationally coal provides a rich revenue stream for governments.
An outburst is the sudden and violent ejection of coal, rock, and gas from a coal face and surrounding strata in an underground coal mine. Outbursts can be a very serious events, possibly even resulting in fatalities.
The health and environmental impact of the coal industry includes issues such as land use, waste management, water and air pollution, caused by the coal mining, processing and the use of its products. In addition to atmospheric pollution, coal burning produces hundreds of millions of tons of solid waste products annually, including fly ash, bottom ash, and flue-gas desulfurization sludge, that contain mercury, uranium, thorium, arsenic, and other heavy metals. Coal is the largest contributor to the human-made increase of carbon dioxide in Earth's atmosphere.
Chatterley Whitfield Colliery is a disused coal mine on the outskirts of Chell, Staffordshire in Stoke on Trent, England. It was the largest mine working the North Staffordshire Coalfield and was the first colliery in the UK to produce one million tons of saleable coal in a year.
The West Stanley Pit disasters refers to two explosions at the West Stanley colliery. West Stanley colliery was a coal mine near Stanley. It opened in 1832 and closed in 1936. Over the years several seams were worked through four shafts: Kettledrum pit, Lamp pit, Mary pit and New pit. In 1882 an underground explosion killed 13 men. In 1909 another explosion took place, killing 168 men. Twenty-nine men survived the disaster.
Environmental impact of mining can occur at local, regional, and global scales through direct and indirect mining practices. Mining can cause erosion, sinkholes, loss of biodiversity, or the contamination of soil, groundwater, and surface water by chemicals emitted from mining processes. These processes also affect the atmosphere through carbon emissions which contributes to climate change.
The summer of 2013–14 was at the time, the most destructive bushfire season in terms of property loss since the 2008–09 Australian bushfire season, with the loss of 371 houses and several hundred non-residential buildings as a result of wild fires between 1 June 2015 and 31 May 2016. The season also suffered 4 fatalities; 2 died in New South Wales, 1 in Western Australia and 1 in Victoria. One death was as a direct result of fire, 2 died due to unrelated health complications while fighting fires on their property, and a pilot contracted by the NSW Rural Fire Service died during an accident.
The Carbondale mine fire was a mine fire in the West Side neighborhood of Carbondale, Lackawanna County, Pennsylvania, in the United States. The fire started in 1946, but was eventually contained by the 1970s. However, it caused at least two fatalities and millions of dollars of property damage.
An der Stinksteinwand in der Nähe des Gasthauses Schwalbenthal strömen im Übrigen seit 300 Jahren durch die Klüfte des Basaltes die Gase eines schwelenden Kohleflözes aus.