Polylactic acid

Last updated

Contents

Polylactic acid
Polylactid sceletal.svg
Identifiers
ChemSpider
  • None
Properties
Density 1210–1430 kg/m3 [1]
Melting point 150 to 160 °C (302 to 320 °F; 423 to 433 K) [1]
0 mg/ml [2]
Hazards
NFPA 704 (fire diamond)
NFPA 704.svgHealth 0: Exposure under fire conditions would offer no hazard beyond that of ordinary combustible material. E.g. sodium chlorideFlammability 1: Must be pre-heated before ignition can occur. Flash point over 93 °C (200 °F). E.g. canola oilInstability 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g. liquid nitrogenSpecial hazards (white): no code
0
1
0
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).

Polylactic acid, also known as poly(lactic acid) or polylactide (PLA), is a plastic material. As a thermoplastic polyester (or polyhydroxyalkanoate) it has the backbone formula (C
3H
4O
2)
n or [–C(CH
3)HC(=O)O–]
n. PLA is formally obtained by condensation of lactic acid C(CH
3)(OH)HCOOH with loss of water (hence its name). It can also be prepared by ring-opening polymerization of lactide [–C(CH
3)HC(=O)O–]
2, the cyclic dimer of the basic repeating unit. Often PLA is blended with other polymers. PLA can be biodegradable or long-lasting, depending on the manufacturing process, additives and copolymers.

PLA has become a popular material due to it being economically produced from renewable resources and the possibility to use it for compostable products. [3] In 2022, PLA had the highest consumption volume of any bioplastic of the world, with a share of ca. 26 % of total bioplastic demand. [4] Although its production is growing, PLA is still not as important as traditional commodity polymers like PET or PVC. Its widespread application has been hindered by numerous physical and processing shortcomings. [5] PLA is the most widely used plastic filament material in FDM 3D printing, due to its low melting point, high strength, low thermal expansion, and good layer adhesion, although it possesses poor heat resistance unless annealed. [6] [7]

Although the name "polylactic acid" is widely used, it does not comply with IUPAC standard nomenclature, which is "poly(lactic acid)". [8] The name "polylactic acid" is potentially ambiguous or confusing, because PLA is not a polyacid (polyelectrolyte), but rather a polyester. [9]

Chemical properties

Synthesis

The monomer is typically made from fermented plant starch such as from corn, cassava, sugarcane or sugar beet pulp.

Several industrial routes afford usable (i.e. high molecular weight) PLA. Two main monomers are used: lactic acid, and the cyclic di-ester, lactide. The most common route to PLA is the ring-opening polymerization of lactide with various metal catalysts (typically tin ethylhexanoate) in solution or as a suspension. The metal-catalyzed reaction tends to cause racemization of the PLA, reducing its stereoregularity compared to the starting material (usually corn starch). [10]

The direct condensation of lactic acid monomers can also be used to produce PLA. This process needs to be carried out at less than 200 °C; above that temperature, the entropically favored lactide monomer is generated. This reaction generates one equivalent of water for every condensation (esterification) step. The condensation reaction is reversible and subject to equilibrium, so removal of water is required to generate high molecular weight species. Water removal by application of a vacuum or by azeotropic distillation is required to drive the reaction toward polycondensation. Molecular weights of 130 kDa can be obtained this way. Even higher molecular weights can be attained by carefully crystallizing the crude polymer from the melt. Carboxylic acid and alcohol end groups are thus concentrated in the amorphous region of the solid polymer, and so they can react. Molecular weights of 128–152 kDa are obtainable thus. [10]

PLA from lactic acid & lactide.png

Another method devised is by contacting lactic acid with a zeolite. This condensation reaction is a one-step process, and runs about 100 °C lower in temperature. [11] [12]

Stereoisomers

Due to the chiral nature of lactic acid, several distinct forms of polylactide exist: poly-L-lactide (PLLA) is the product resulting from polymerization of L,L-lactide (also known as L-lactide). Progress in biotechnology has resulted in the development of commercial production of the D enantiomer form. [13]

Polymerization of a racemic mixture of L- and D-lactides usually leads to the synthesis of poly-DL-lactide (PDLLA), which is amorphous. Use of stereospecific catalysts can lead to heterotactic PLA which has been found to show crystallinity. The degree of crystallinity, and hence many important properties, is largely controlled by the ratio of D to L enantiomers used, and to a lesser extent on the type of catalyst used. Apart from lactic acid and lactide, lactic acid O-carboxyanhydride ("lac-OCA"), a five-membered cyclic compound has been used academically as well. This compound is more reactive than lactide, because its polymerization is driven by the loss of one equivalent of carbon dioxide per equivalent of lactic acid. Water is not a co-product. [14]

The direct biosynthesis of PLA, in a manner similar to production of poly(hydroxyalkanoate)s, has been reported. [15]

Physical properties

PLA polymers range from amorphous glassy polymer to semi-crystalline and highly crystalline polymer with a glass transition 60–65 °C, a melting temperature 130-180 °C, and a Young's modulus 2.7–16 GPa. [16] [17] [18] Heat-resistant PLA can withstand temperatures of 110 °C. [19] The basic mechanical properties of PLA are between those of polystyrene and PET. [16] The melting temperature of PLLA can be increased by 40–50 °C and its heat deflection temperature can be increased from approximately 60 °C to up to 190 °C by physically blending the polymer with PDLA (poly-D-lactide). PDLA and PLLA form a highly regular stereocomplex with increased crystallinity. The temperature stability is maximised when a 1:1 blend is used, but even at lower concentrations of 3–10% of PDLA, there is still a substantial improvement. In the latter case, PDLA acts as a nucleating agent, thereby increasing the crystallization rate. [20] Biodegradation of PDLA is slower than for PLA due to the higher crystallinity of PDLA[ citation needed ]. The flexural modulus of PLA is higher than polystyrene and PLA has good heat sealability.

Although PLA performs mechanically similar to PET for properties of tensile strength and elastic modulus, the material is very brittle and results in less than 10% elongation at break. [21] Furthermore, this limits PLA’s use in applications that require some level of plastic deformation at high stress levels. An effort to increase the elongation at break for PLA has been underway, especially to bolster PLA’s presence as a commodity plastic and improve the bioplastics landscape. For example, PLLA biocomposites have been of interest to improve these mechanical properties. By mixing PLLA with poly (3-hydroxy butyrate) (PHB), cellulose nano crystal (CNC) and a plasticizer (TBC), a drastic improvement of mechanical properties were shown. [22] Using polarized optical microscopy (POM), the PLLA biocomposites had smaller spherulites compared to pure PLLA, indicating improved nucleation density and also contributing to an increase of elongation at break from 6% in pure PLLA to 140-190% in the biocomposites. Biocomposites such as these are of great interest for food packaging because of their improved strength and biodegradability.

Several technologies such as annealing, [23] [24] [25] adding nucleating agents, forming composites with fibers or nano-particles, [26] [27] [28] chain extending [29] [30] and introducing crosslink structures have been used to enhance the mechanical properties of PLA polymers. Annealing has been shown to significantly increase the degree of crystallinity of PLA polymers. In one study, increasing the duration of annealing directly affected thermal conductivity, density, and the glass transition temperature. [31] Structural changes from this treatment further improved characteristics such as compressive strength and rigidity by nearly 80%. Processes such as this may boost PLA’s presence in the plastics market, as improving the mechanical properties will be important to replace current petroleum-derived plastics. It has also been demonstrated that the addition of a PLA-based, cross-linked nucleating agent improved the degree of crystallinity of the final PLA material. [7] Alongside the use of the nucleating agent, annealing was shown to further improve the degree of crystallinity and, therefore, the toughness and flexural modulus of the material. This example reveals the ability to utilize multiple of these processes to reinforce the mechanical properties of PLA. Polylactic acid can be processed like most thermoplastics into fiber (for example, using conventional melt spinning processes) and film. PLA has similar mechanical properties to PETE polymer, but has a significantly lower maximum continuous use temperature. [32]

Backbone architecture of PLA and its effect on crystallization kinetics has also been investigated, specifically to better understand the most suitable processing conditions for PLA. The molecular weight of polymer chains can play a significant role in the mechanical properties. [33] One method of increasing molecular weight is by introducing branches of the same polymer chain onto the backbone. Through characterization of a branched and linear grade PLA, branched PLA leads to faster crystallization. [34] Furthermore, the branched PLA experiences much longer relaxation times at low shear rates, contributing to higher viscosity than the linear grade. This is presumed to be from high molecular weight regions within the branched PLA. However, the branched PLA was observed to shear thin more strongly, leading to a much lower viscosity at high shear rates. Understanding properties such as these are crucial when determining optimal processing conditions for materials, and that simple changes to the structure can alter its behavior dramatically.

Racemic PLA and pure PLLA have low glass transition temperatures, making them undesirable because of low strength and melting point. A stereocomplex of PDLA and PLLA has a higher glass transition temperature, lending it more mechanical strength. [35]

The high surface energy of PLA results in good printability, making it widely used in 3D printing. The tensile strength for 3D printed PLA was previously determined. [36]

Solvents

PLA is soluble in a range of organic solvents. [37] Ethyl acetate is widely used because of its ease of access and low risk. It is useful in 3D printers for cleaning the extruder heads and for removing PLA supports.

Other safe solvents include propylene carbonate, which is safer than ethyl acetate but is difficult to purchase commercially. Pyridine can be used, but it has a distinct fish odor and is less safe than ethyl acetate. PLA is also soluble in hot benzene, tetrahydrofuran, and dioxane. [38]

Fabrication

PLA objects can be fabricated by 3D printing, casting, injection moulding, extrusion, machining, and solvent welding.

PLA filament for use in 3D printing Bobina PLA.jpg
PLA filament for use in 3D printing

PLA is used as a feedstock material in desktop fused filament fabrication by 3D printers, such as RepRap printers. [39] [40]

PLA can be solvent welded using dichloromethane. [41] Acetone also softens the surface of PLA, making it sticky without dissolving it, for welding to another PLA surface. [42]

A corn form 3D printed using corn-derivative PLA (polylactic acid).

PLA-printed solids can be encased in plaster-like moulding materials, then burned out in a furnace, so that the resulting void can be filled with molten metal. This is known as "lost PLA casting", a type of investment casting. [43]

Applications

PLA is mainly used for short-lived and disposable packaging. In 2022, of the total PLA production, ca. 35 % was used for flexible packaging (e.g. films, bags, labels) and 30 % for rigid packaging (e.g. bottles, jars, containers). [44]

Consumer goods

PLA is used in a large variety of consumer products such as disposable tableware, cutlery, housings for kitchen appliances and electronics such as laptops and handheld devices, and microwavable trays. (However, PLA is not suitable for microwavable containers because of its low glass transition temperature.) It is used for compost bags, food packaging and loose-fill packaging material that is cast, injection molded, or spun. [45] In the form of a film, it shrinks upon heating, allowing it to be used in shrink tunnels. In the form of fibers, it is used for monofilament fishing line and netting. In the form of nonwoven fabrics, it is used for upholstery, disposable garments, awnings, feminine hygiene products, and diapers.

PLA has applications in engineering plastics, where the stereocomplex is blended with a rubber-like polymer such as ABS. Such blends have good form stability and visual transparency, making them useful in low-end packaging applications.

PLA is used for automotive parts such as floor mats, panels, and covers. Its heat resistance and durability are inferior to the widely used polypropylene (PP), but its properties are improved by means such as capping of the end groups to reduce hydrolysis. [45]

Agricultural

In the form of fibers, PLA is used for monofilament fishing line and netting for vegetation and weed prevention. It is used for sandbags, planting pots, binding tape and ropes . [45]

Medical

PLA can degrade into innocuous lactic acid, making it suitable for use as medical implants in the form of anchors, screws, plates, pins, rods, and mesh. [45] Depending on the type used, it breaks down inside the body within 6 months to 2 years. This gradual degradation is desirable for a support structure, because it gradually transfers the load to the body (e.g., to the bone) as that area heals. The strength characteristics of PLA and PLLA implants are well documented. [46]

Thanks to its bio-compatibility and biodegradability, PLA found interest as a polymeric scaffold for drug delivery purposes.

The composite blend of poly(L-lactide-co-D,L-lactide) (PLDLLA) with tricalcium phosphate (TCP) is used as PLDLLA/TCP scaffolds for bone engineering. [47] [48]

Poly-L-lactic acid (PLLA) is the main ingredient in Sculptra, a facial volume enhancer used for treating lipoatrophy of the cheeks.

PLLA is used to stimulate collagen synthesis in fibroblasts via foreign body reaction in the presence of macrophages. Macrophages act as a stimulant in secretion of cytokines and mediators such as TGF-β, which stimulate the fibroblast to secrete collagen into the surrounding tissue. Therefore, PLLA has potential applications in the dermatological studies. [49] [50]

PLLA is under investigation as a scaffold that can generate a small amount of electric current via the piezoelectric effect that stimulates the growth of mechanically robust cartilage in multiple animal models. [51]

Degradation

PLA is generally considered to be compostable in industrial composting conditions but not in home compost, based off of the results of tests done using EN 13432 and ASTM D6400 standards. However, certain isomers of PLA such as PLLA or PDLA have been shown to have varying rates of degradation. [53]

PLA is degraded abiotically by three mechanisms: [54]

  1. Hydrolysis: The ester groups of the main chain are cleaved, thus reducing molecular weight.
  2. Thermal decomposition: A complex phenomenon leading to the appearance of different compounds such as lighter molecules and linear and cyclic oligomers with different Mw, and lactide.
  3. Photodegradation: UV radiation induces degradation. This is a factor mainly where PLA is exposed to sunlight in its applications in plasticulture, packaging containers and films.

The hydrolytic reaction is:

-COO- + H2O → -COOH + -OH

The degradation rate is very slow in ambient temperatures. A 2017 study found that at 25 °C (77 °F) in seawater, PLA showed no loss of mass over a year, but the study did not measure breakdown of the polymer chains or water absorption. [55] As a result, it degrades poorly in landfills and household composts, but is effectively digested in hotter industrial composts, usually degrading best at temperatures of over 60 °C (140 °F). [56]

Pure PLA foams are selectively hydrolysed in Dulbecco's modified Eagle's medium (DMEM) supplemented with fetal bovine serum (FBS) (a solution mimicking body fluid). After 30 days of submersion in DMEM+FBS, a PLLA scaffold lost about 20% of its weight. [57]

PLA samples of various molecular weights were degraded into methyl lactate (a green solvent) by using a metal complex catalyst. [58] [59] [60]

PLA can also be degraded by some bacteria, such as Amycolatopsis and Saccharothrix . A purified protease from Amycolatopsis sp., PLA depolymerase, can also degrade PLA. Enzymes such as pronase and most effectively proteinase K from Tritirachium album degrade PLA. [61]

End of life

PLA has SPI resin ID code 7 Symbol Resin Code 7.svg
PLA has SPI resin ID code 7

Four possible end-of-life scenarios are the most common:

  1. Recycling: [62] which can be either chemical or mechanical. Currently, the SPI resin identification code 7 ("others") is applicable for PLA. In Belgium, Galactic started the first pilot unit to chemically recycle PLA (Loopla). [63] Unlike mechanical recycling, waste material can hold various contaminants. Polylactic acid can be chemically recycled to monomer by thermal depolymerization or hydrolysis. When purified, the monomer can be used for the manufacturing of virgin PLA with no loss of original properties [64] (cradle-to-cradle recycling).[ dubious – discuss ] End-of-life PLA can be chemically recycled to methyl lactate by transesterification. [60]
  2. Composting: PLA is biodegradable under industrial composting conditions, starting with chemical hydrolysis process, followed by microbial digestion, to ultimately degrade the PLA. Under industrial composting conditions (58 °C (136 °F)), PLA can partly (about half) decompose into water and carbon dioxide in 60 days, after which the remainder decomposes much more slowly, [65] with the rate depending on the material's degree of crystallinity. [66] Environments without the necessary conditions will see very slow decomposition akin to that of non-bioplastics, not fully decomposing for hundreds or thousands of years. [67]
  3. Incineration: PLA can be incinerated without producing chlorine-containing chemicals or heavy metals because it contains only carbon, oxygen, and hydrogen atoms. Since it does not contain chlorine it does not produce dioxins or hydrochloric acid during incineration. [68] PLA can be combusted with no remaining residue. This and other results suggest that incineration is an environmentally friendly disposal of waste PLA. [69] Upon being incinerated, PLA can release carbon dioxide. [70]
  4. Landfill: the least preferable option is landfilling because PLA degrades very slowly in ambient temperatures, often as slowly as other plastics. [67]

See also

Related Research Articles

<span class="mw-page-title-main">Biopolymer</span> Polymer produced by a living organism

Biopolymers are natural polymers produced by the cells of living organisms. Like other polymers, biopolymers consist of monomeric units that are covalently bonded in chains to form larger molecules. There are three main classes of biopolymers, classified according to the monomers used and the structure of the biopolymer formed: polynucleotides, polypeptides, and polysaccharides. The Polynucleotides, RNA and DNA, are long polymers of nucleotides. Polypeptides include proteins and shorter polymers of amino acids; some major examples include collagen, actin, and fibrin. Polysaccharides are linear or branched chains of sugar carbohydrates; examples include starch, cellulose, and alginate. Other examples of biopolymers include natural rubbers, suberin and lignin, cutin and cutan, melanin, and polyhydroxyalkanoates (PHAs).

<span class="mw-page-title-main">Biodegradation</span> Decomposition by living organisms

Biodegradation is the breakdown of organic matter by microorganisms, such as bacteria and fungi. It is generally assumed to be a natural process, which differentiates it from composting. Composting is a human-driven process in which biodegradation occurs under a specific set of circumstances.

Ingeo is a range of polylactic acid (PLA) biopolymers owned by NatureWorks. Resinex Group distributes Ingeo in Europe.

<span class="mw-page-title-main">Polyglycolide</span> Chemical compound

Polyglycolide or poly(glycolic acid) (PGA), also spelled as polyglycolic acid, is a biodegradable, thermoplastic polymer and the simplest linear, aliphatic polyester. It can be prepared starting from glycolic acid by means of polycondensation or ring-opening polymerization. PGA has been known since 1954 as a tough fiber-forming polymer. Owing to its hydrolytic instability, however, its use has initially been limited. Currently polyglycolide and its copolymers (poly(lactic-co-glycolic acid) with lactic acid, poly(glycolide-co-caprolactone) with ε-caprolactone and poly (glycolide-co-trimethylene carbonate) with trimethylene carbonate) are widely used as a material for the synthesis of absorbable sutures and are being evaluated in the biomedical field.

<span class="mw-page-title-main">Polyhydroxyalkanoates</span> Polyester family

Polyhydroxyalkanoates or PHAs are polyesters produced in nature by numerous microorganisms, including through bacterial fermentation of sugars or lipids. When produced by bacteria they serve as both a source of energy and as a carbon store. More than 150 different monomers can be combined within this family to give materials with extremely different properties. These plastics are biodegradable and are used in the production of bioplastics.

<span class="mw-page-title-main">Lactide</span> Chemical compound

Lactide is the lactone cyclic ester derived by multiple esterification between two (usually) or more molecules from lactic acid or other hydroxy carboxylic acid. They are designated as dilactides, trilactides, etc., according to the number of hydroxy acid residues. The dilactide derived from lactic acid has the formula [CH(CH3)CO2]2. All lactides are colorless or white solids. This lactide has attracted interest because it is derived from abundant renewable resources and is the precursor to a biodegradable plastic.

<span class="mw-page-title-main">PLGA</span> Copolymer of varying ratios of polylactic acid and polyglycolic acid

PLGA, PLG, or poly(lactic-co-glycolic) acid is a copolymer which is used in a host of Food and Drug Administration (FDA) approved therapeutic devices, owing to its biodegradability and biocompatibility. PLGA is synthesized by means of ring-opening co-polymerization of two different monomers, the cyclic dimers (1,4-dioxane-2,5-diones) of glycolic acid and lactic acid. Polymers can be synthesized as either random or block copolymers thereby imparting additional polymer properties. Common catalysts used in the preparation of this polymer include tin(II) 2-ethylhexanoate, tin(II) alkoxides, or aluminum isopropoxide. During polymerization, successive monomeric units are linked together in PLGA by ester linkages, thus yielding a linear, aliphatic polyester as a product.

<span class="mw-page-title-main">Bioplastic</span> Plastics derived from renewable biomass sources

Bioplastics are plastic materials produced from renewable biomass sources. Historically, bioplastics made from natural materials like shellac or cellulose had been the first plastics. Since the end of the 19th century they have been increasingly superseded by fossil-fuel plastics derived from petroleum or natural gas. Today, in the context of bioeconomy and circular economy, bioplastics are gaining interest again. Conventional petro-based polymers are increasingly blended with bioplastics to manufacture "bio-attributed" or "mass-balanced" plastic products - so the difference between bio- and other plastics might be difficult to define.

Alpha hydroxy carboxylic acids, or α-hydroxy carboxylic acids (AHAs), are a group of carboxylic acids featuring a hydroxy group located one carbon atom away from the acid group. This structural aspect distinguishes them from beta hydroxy acids, where the functional groups are separated by two carbon atoms. Notable AHAs include glycolic acid, lactic acid, mandelic acid, and citric acid.

<span class="mw-page-title-main">Polydioxanone</span>

Polydioxanone or poly-p-dioxanone is a colorless, crystalline, biodegradable synthetic polymer.

<span class="mw-page-title-main">Biodegradable plastic</span> Plastics that can be decomposed by the action of living organisms

Biodegradable plastics are plastics that can be decomposed by the action of living organisms, usually microbes, into water, carbon dioxide, and biomass. Biodegradable plastics are commonly produced with renewable raw materials, micro-organisms, petrochemicals, or combinations of all three.

PBAT is a biodegradable random copolymer, specifically a copolyester of adipic acid, 1,4-butanediol and terephthalic acid. PBAT is produced by many different manufacturers and may be known by the brand names ecoflex, Wango,Ecoworld, Eastar Bio, and Origo-Bi. It is also called poly(butylene adipate-co-terephthalate) and sometimes polybutyrate-adipate-terephthalate or even just "polybutyrate". It is generally marketed as a fully biodegradable alternative to low-density polyethylene, having many similar properties including flexibility and resilience, allowing it to be used for many similar uses such as plastic bags and wraps. The structure is a random-block polymer consisting of butanediol–adipic acid and butanediol-terephthalic acid blocks.

Biodegradable polymers are a special class of polymer that breaks down after its intended purpose by bacterial decomposition process to result in natural byproducts such as gases (CO2, N2), water, biomass, and inorganic salts. These polymers are found both naturally and synthetically made, and largely consist of ester, amide, and ether functional groups. Their properties and breakdown mechanism are determined by their exact structure. These polymers are often synthesized by condensation reactions, ring opening polymerization, and metal catalysts. There are vast examples and applications of biodegradable polymers.

In polymer chemistry, the term prepolymer or pre-polymer, refers to a monomer or system of monomers that have been reacted to an intermediate-molecular mass state. This material is capable of further polymerization by reactive groups to a fully cured, high-molecular-mass state. As such, mixtures of reactive polymers with un-reacted monomers may also be referred to as pre-polymers. The term "pre-polymer" and "polymer precursor" may be interchanged.

<span class="mw-page-title-main">PHBV</span> Chemical compound

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate), commonly known as PHBV, is a polyhydroxyalkanoate-type polymer. It is biodegradable, nontoxic, biocompatible plastic produced naturally by bacteria and a good alternative for many non-biodegradable synthetic polymers. It is a thermoplastic linear aliphatic polyester. It is obtained by the copolymerization of 3-hydroxybutanoic acid and 3-hydroxypentanoic acid. PHBV is used in speciality packaging, orthopedic devices and in controlled release of drugs. PHBV undergoes bacterial degradation in the environment.

Biodegradable additives are additives that enhance the biodegradation of polymers by allowing microorganisms to utilize the carbon within the polymer chain as a source of energy. Biodegradable additives attract microorganisms to the polymer through quorum sensing after biofilm creation on the plastic product. Additives are generally in masterbatch formation that use carrier resins such as polyethylene (PE), polypropylene (PP), polystyrene (PS) or polyethylene terephthalate (PET).

Poly(ethylene adipate) or PEA is an aliphatic polyester. It is most commonly synthesized from a polycondensation reaction between ethylene glycol and adipic acid. PEA has been studied as it is biodegradable through a variety of mechanisms and also fairly inexpensive compared to other polymers. Its lower molecular weight compared to many polymers aids in its biodegradability.

<span class="mw-page-title-main">Biodegradable athletic footwear</span>

Biodegradable athletic footwear is athletic footwear that uses biodegradable materials with the ability to compost at the end-of-life phase. Such materials include natural biodegradable polymers, synthetic biodegradable polymers, and biodegradable blends. The use of biodegradable materials is a long-term solution to landfill pollution that can significantly help protect the natural environment by replacing the synthetic, non-biodegradable polymers found in athletic footwear.

Biofoams are biological or biologically derived foams, making up lightweight and porous cellular solids. A relatively new term, its use in academia began in the 1980s in relation to the scum that formed on activated sludge plants.

<span class="mw-page-title-main">Poly(trimethylene carbonate)</span> Polycarbonate

Poly(trimethylene carbonate) (PTMC) is an aliphatic polycarbonate synthesized from the 6-membered cyclic carbonate, trimethylene carbonate (1,3-propylene carbonate or 1,3-Dioxan-2-one). Trimethylene carbonate (TMC) is a colorless crystalline solid with melting point ranging between 45°C and 48 °C and boiling point at 255°C (at 760 mmHg). TMC is originally synthesized from 1,3-propanediol with phosgene or carbon monoxide, which are highly poisonous gases. Another route is from the transesterification of 1,3-propanediol and dialkylcarbonates. This route is considered "greener" compared to the other one, since precursors can be obtained from renewable resources and carbon dioxide.

References

  1. 1 2 "Material Properties of Polylactic Acid (PLA), Agro Based Polymers". Matbase - Material Properties Database. Archived from the original on 10 February 2012. Retrieved 6 February 2012.
  2. ↑ "Polylactic Acid. Material Safety Data Sheet" (PDF). ampolymer.com. Archived from the original (PDF) on 6 January 2009.
  3. ↑ Teixeira LV, Bomtempo JV, Oroski Fd, Coutinho PL (2023). "The Diffusion of Bioplastics: What Can We Learn from Poly(Lactic Acid)?". Sustainability . 15 (6): 4699. doi: 10.3390/su15064699 .
  4. ↑ Ceresana. "Bioplastics - Study: Market, Analysis, Trends - Ceresana". www.ceresana.com. Retrieved 25 October 2024.
  5. ↑ Nagarajan V, Mohanty AK, Misra M (2016). "Perspective on Polylactic Acid (PLA) based Sustainable Materials for Durable Applications: Focus on Toughness and Heat Resistance". ACS Sustainable Chemistry & Engineering. 4 (6): 2899–2916. doi: 10.1021/acssuschemeng.6b00321 .
  6. ↑ "Worldwide most used 3D printing materials, as of July 2018" . Retrieved 19 January 2024.
  7. 1 2 Simmons H, Tiwary P, Colwell JE, Kontopoulou M (August 2019). "Improvements in the crystallinity and mechanical properties of PLA by nucleation and annealing". Polymer Degradation and Stability. 166: 248–257. doi:10.1016/j.polymdegradstab.2019.06.001. S2CID   195550926.
  8. ↑ Vert M, Chen J, Hellwich KH, Hodge P, Nakano T, Scholz C, et al. "Nomenclature and Terminology for Linear Lactic Acid-Based Polymers (IUPAC Recommendations 2019)". IUPAC Standards Online. doi:10.1515/iupac.92.0001.
  9. ↑ Martin O, Avérous L (2001). "Poly(lactic acid): plasticization and properties of biodegradable multiphase systems". Polymer. 42 (14): 6209–6219. doi:10.1016/S0032-3861(01)00086-6.
  10. 1 2 Södergård A, Stolt M (2010). "3. Industrial Production of High Molecular Weight Poly(Lactic Acid)". In Auras R, Lim LT, Selke SE, Tsuji H (eds.). Poly(Lactic Acid): Synthesis, Structures, Properties, Processing, and Applications. pp. 27–41. doi:10.1002/9780470649848.ch3. ISBN   978-0-470-64984-8.
  11. ↑ Drury J (15 February 2016). "Cheaper, greener, route to bioplastic". reuters.com. Archived from the original on 1 December 2017. Retrieved 9 May 2018.
  12. ↑ Dusselier M, Van Wouwe P, Dewaele A, Jacobs PA, Sels BF (July 2015). "GREEN CHEMISTRY. Shape-selective zeolite catalysis for bioplastics production". Science. 349 (6243): 78–80. Bibcode:2015Sci...349...78D. doi:10.1126/science.aaa7169. PMID   26138977. S2CID   206635718.
  13. ↑ "Bioengineers succeed in producing plastic without the use of fossil fuels". Physorg.com. Archived from the original on 6 June 2011. Retrieved 11 April 2011.
  14. ↑ Kricheldorf HR, Jonté JM (1983). "New polymer syntheses". Polymer Bulletin. 9 (6–7). doi:10.1007/BF00262719. S2CID   95429767.
  15. ↑ Jung YK, Kim TY, Park SJ, Lee SY (January 2010). "Metabolic engineering of Escherichia coli for the production of polylactic acid and its copolymers". Biotechnology and Bioengineering. 105 (1): 161–171. doi:10.1002/bit.22548. PMID   19937727. S2CID   205499487.
  16. 1 2 Lunt J (3 January 1998). "Large-scale production, properties and commercial applications of polylactic acid polymers". Polymer Degradation and Stability. 59 (1–3): 145–152. doi:10.1016/S0141-3910(97)00148-1. ISSN   0141-3910.
  17. ↑ Södergård A, Stolt M (February 2002). "Properties of lactic acid based polymers and their correlation with composition". Progress in Polymer Science. 27 (6): 1123–1163. doi:10.1016/S0079-6700(02)00012-6.
  18. ↑ Middleton JC, Tipton AJ (December 2000). "Synthetic biodegradable polymers as orthopedic devices". Biomaterials. 21 (23): 2335–2346. doi:10.1016/S0142-9612(00)00101-0. PMID   11055281.
  19. ↑ Fiore GL, Jing F, Young Jr VG, Cramer CJ, Hillmyer MA (2010). "High Tg Aliphatic Polyesters by the Polymerization of Spirolactide Derivatives". Polymer Chemistry. 1 (6): 870–877. doi:10.1039/C0PY00029A.
  20. ↑ Park HS, Hong CK (June 2021). "Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends". Polymers. 13 (11): 1851. doi: 10.3390/polym13111851 . PMC   8199684 . PMID   34199577.
  21. ↑ Farah S, Anderson DG, Langer R (December 2016). "Physical and mechanical properties of PLA, and their functions in widespread applications - A comprehensive review". Advanced Drug Delivery Reviews. 107: 367–392. doi:10.1016/j.addr.2016.06.012. hdl: 1721.1/112940 . PMID   27356150.
  22. ↑ El-Hadi AM (May 2017). "Increase the elongation at break of poly (lactic acid) composites for use in food packaging films". Scientific Reports. 7 (1): 46767. Bibcode:2017NatSR...746767E. doi:10.1038/srep46767. PMC   5413939 . PMID   28466854.
  23. ↑ Nugroho P, Mitomo H, Yoshii F, Kume T (1 May 2001). "Degradation of poly(l-lactic acid) by γ-irradiation". Polymer Degradation and Stability. 72 (2): 337–343. doi:10.1016/S0141-3910(01)00030-1. ISSN   0141-3910.
  24. ↑ Urayama H, Kanamori T, Fukushima K, Kimura Y (1 September 2003). "Controlled crystal nucleation in the melt-crystallization of poly(l-lactide) and poly(l-lactide)/poly(d-lactide) stereocomplex". Polymer. 44 (19): 5635–5641. doi:10.1016/S0032-3861(03)00583-4. ISSN   0032-3861.
  25. ↑ Tsuji H (1 January 1995). "Properties and morphologies of poly(l-lactide): 1. Annealing condition effects on properties and morphologies of poly(l-lactide)". Polymer. 36 (14): 2709–2716. doi:10.1016/0032-3861(95)93647-5. ISSN   0032-3861.
  26. ↑ Urayama H, Ma C, Kimura Y (July 2003). "Mechanical and Thermal Properties of Poly(L-lactide) Incorporating Various Inorganic Fillers with Particle and Whisker Shapes". Macromolecular Materials and Engineering. 288 (7): 562–568. doi:10.1002/mame.200350004. ISSN   1438-7492.
  27. ↑ Trimaille T, Pichot C, Elaissari A, Fessi H, Briançon S, Delair T (1 November 2003). "Poly(d,l-lactic acid) nanoparticle preparation and colloidal characterization". Colloid and Polymer Science. 281 (12): 1184–1190. doi:10.1007/s00396-003-0894-1. ISSN   0303-402X. S2CID   98078359.
  28. ↑ Hu X, Xu HS, Li ZM (4 May 2007). "Morphology and Properties of Poly(L-Lactide) (PLLA) Filled with Hollow Glass Beads". Macromolecular Materials and Engineering. 292 (5): 646–654. doi:10.1002/mame.200600504. ISSN   1438-7492.
  29. ↑ Li BH, Yang MC (2006). "Improvement of thermal and mechanical properties of poly(L-lactic acid) with 4,4-methylene diphenyl diisocyanate". Polymers for Advanced Technologies. 17 (6): 439–443. doi:10.1002/pat.731. ISSN   1042-7147. S2CID   98536537.
  30. ↑ Di Y, Iannace S, Di Maio E, Nicolais L (4 November 2005). "Reactively Modified Poly(lactic acid): Properties and Foam Processing". Macromolecular Materials and Engineering. 290 (11): 1083–1090. doi:10.1002/mame.200500115. ISSN   1438-7492.
  31. ↑ Barkhad MS, Abu-Jdayil B, Mourad AH, Iqbal MZ (September 2020). "Thermal Insulation and Mechanical Properties of Polylactic Acid (PLA) at Different Processing Conditions". Polymers. 12 (9): 2091. doi: 10.3390/polym12092091 . PMC   7570036 . PMID   32938000.
  32. ↑ "Compare Materials: PLA and PETE". Makeitfrom.com. Archived from the original on 1 May 2011. Retrieved 11 April 2011.
  33. ↑ Nunes RW, Martin JR, Johnson JF (March 1982). "Influence of molecular weight and molecular weight distribution on mechanical properties of polymers". Polymer Engineering & Science. 22 (4): 205–228. doi:10.1002/pen.760220402. ISSN   0032-3888.
  34. ↑ Dorgan JR, Lehermeier H, Mang M (January 2000). "Thermal and Rheological Properties of Commercial-Grade Poly(Lactic Acid)s". Journal of Polymers and the Environment. 8 (1): 1–9. doi:10.1023/A:1010185910301. ISSN   1572-8900.
  35. ↑ Luo F, Fortenberry A, Ren J, Qiang Z (20 August 2020). "Recent Progress in Enhancing Poly(Lactic Acid) Stereocomplex Formation for Material Property Improvement". Frontiers in Chemistry. 8: 688. Bibcode:2020FrCh....8..688L. doi: 10.3389/fchem.2020.00688 . PMC   7468453 . PMID   32974273.
  36. ↑ Giordano RA, Wu BM, Borland SW, Cima LG, Sachs EM, Cima MJ (1997). "Mechanical properties of dense polylactic acid structures fabricated by three dimensional printing". Journal of Biomaterials Science. Polymer Edition. 8 (1): 63–75. doi:10.1163/156856297x00588. PMID   8933291.
  37. ↑ Sato S, Gondo D, Wada T, Kanehashi S, Nagai K (2013). "Effects of Various Liquid Organic Solvents on Solvent-Induced Crystallization of AMorphous Poly(lactic acid) Film". Journal of Applied Polymer Science. 129 (3): 1607–1617. doi:10.1002/app.38833.
  38. ↑ Garlotta D (2001). "A Literature Review of Poly(Lactic Acid)". Journal of Polymers and the Environment. 9 (2): 63–84. doi:10.1023/A:1020200822435. S2CID   8630569. Archived from the original on 26 May 2013.
  39. ↑ "PLA". Reprap Wiki. 4 April 2011. Archived from the original on 16 July 2011. Retrieved 11 April 2011.
  40. ↑ "PLA". MakerBot Industries. Archived from the original on 23 April 2011. Retrieved 11 April 2011.
  41. ↑ Coysh A (12 April 2013). "Dichloromethane Vapor Treating PLA parts". Thingiverse.com. Archived from the original on 1 December 2017. Retrieved 9 May 2018.
  42. ↑ Sanladerer T (9 December 2016). "Does Acetone also work for welding and smoothing PLA 3D printed parts?". youtube.com. Archived from the original on 21 December 2021. Retrieved 9 January 2021.
  43. ↑ "Metal Casting with Your 3D Printer". Make: DIY Projects and Ideas for Makers. Retrieved 30 November 2018.
  44. ↑ "Polylactic Acid Market Report: Industry Analysis | 2022-2032". Ceresana Market Research. Retrieved 25 October 2024.
  45. 1 2 3 4 Auras R, Lim LT, Selke SE, Tsuji H, eds. (2010). Poly(Lactic Acid): Synthesis, Structures, Properties, Processing, and Applications. doi:10.1002/9780470649848. ISBN   978-0-470-29366-9.
  46. ↑ Nazre A, Lin S (1994). Harvey JP, Games RF (eds.). Theoretical Strength Comparison of Bioabsorbable (PLLA) Plates and Conventional Stainless Steel and Titanium Plates Used in Internal Fracture Fixation. ASTM International. p. 53. ISBN   978-0-8031-1897-3.
  47. ↑ Lam CX, Olkowski R, Swieszkowski W, Tan KC, Gibson I, Hutmacher DW (2008). "Mechanical and in vitro evaluations of composite PLDLLA/TCP scaffolds for bone engineering". Virtual and Physical Prototyping. 3 (4): 193–197. doi:10.1080/17452750802551298. S2CID   135582844.
  48. ↑ Bose S, Vahabzadeh S, Bandyopadhyay A (2013). "Bone tissue engineering using 3D printing". Materials Today. 16 (12): 496–504. doi: 10.1016/j.mattod.2013.11.017 .
  49. ↑ Ray S, Adelnia H, Ta HT (September 2021). "Collagen and the effect of poly-l-lactic acid based materials on its synthesis". Biomaterials Science. 9 (17): 5714–5731. doi:10.1039/d1bm00516b. hdl: 10072/405917 . PMID   34296717. S2CID   236199608.
  50. ↑ Ray S, Ta HT (July 2020). "Investigating the Effect of Biomaterials Such as Poly-(l-Lactic Acid) Particles on Collagen Synthesis In Vitro: Method Is Matter". Journal of Functional Biomaterials. 11 (3): 51. doi: 10.3390/jfb11030051 . PMC   7564527 . PMID   32722074.
  51. ↑ Petersen M (18 January 2022). "Electric knee implants could help millions of arthritis patients". ZME Science. Retrieved 19 January 2022.
  52. ↑ Guo SZ, Yang X, Heuzey MC, Therriault D (2015). "3D printing of a multifunctional nanocomposite helical liquid sensor". Nanoscale. 7 (15): 6451–6. Bibcode:2015Nanos...7.6451G. doi:10.1039/C5NR00278H. PMID   25793923.
  53. ↑ Quynh TM, Mitomo H, Nagasawa N, Wada Y, Yoshii F, Tamada M (May 2007). "Properties of crosslinked polylactides (PLLA & PDLA) by radiation and its biodegradability". European Polymer Journal. 43 (5): 1779–1785. Bibcode:2007EurPJ..43.1779Q. doi:10.1016/j.eurpolymj.2007.03.007. ISSN   0014-3057.
  54. ↑ Castro-Aguirre E, Iñiguez-Franco F, Samsudin H, Fang X, Auras R (December 2016). "Poly(lactic acid)-Mass production, processing, industrial applications, and end of life". Advanced Drug Delivery Reviews. 107: 333–366. doi: 10.1016/j.addr.2016.03.010 . PMID   27046295.
  55. ↑ Bagheri AR, Laforsch C, Greiner A, Agarwal S (July 2017). "Fate of So-Called Biodegradable Polymers in Seawater and Freshwater". Global Challenges. 1 (4): 1700048. Bibcode:2017GloCh...100048B. doi: 10.1002/gch2.201700048 . PMC   6607129 . PMID   31565274.
  56. ↑ "Is PLA Biodegradable? – The Truth". All3DP. 10 December 2019. Retrieved 26 June 2021.
  57. ↑ Pavia FC, La Carrubba V, Piccarolo S, Brucato V (August 2008). "Polymeric scaffolds prepared via thermally induced phase separation: tuning of structure and morphology". Journal of Biomedical Materials Research. Part A. 86 (2): 459–466. doi:10.1002/jbm.a.31621. PMID   17975822.
  58. ↑ Román-Ramírez LA, Mckeown P, Jones MD, Wood J (4 January 2019). "Poly(lactic acid) Degradation into Methyl Lactate Catalyzed by a Well-Defined Zn(II) Complex". ACS Catalysis. 9 (1): 409–416. doi: 10.1021/acscatal.8b04863 .
  59. ↑ McKeown P, Román-Ramírez LA, Bates S, Wood J, Jones MD (November 2019). "Zinc Complexes for PLA Formation and Chemical Recycling: Towards a Circular Economy". ChemSusChem. 12 (24): 5233–5238. Bibcode:2019ChSCh..12.5233M. doi:10.1002/cssc.201902755. PMID   31714680. S2CID   207941305.
  60. 1 2 Román-Ramírez LA, McKeown P, Shah C, Abraham J, Jones MD, Wood J (June 2020). "Chemical Degradation of End-of-Life Poly(lactic acid) into Methyl Lactate by a Zn(II) Complex". Industrial & Engineering Chemistry Research. 59 (24): 11149–11156. doi: 10.1021/acs.iecr.0c01122 . PMC   7304880 . PMID   32581423.
  61. ↑ Tokiwa Y, Calabia BP, Ugwu CU, Aiba S (August 2009). "Biodegradability of plastics". International Journal of Molecular Sciences. 10 (9): 3722–3742. doi: 10.3390/ijms10093722 . PMC   2769161 . PMID   19865515.
  62. ↑ Dash A, Kabra S, Misra S, Hrishikeshan G, Singh RP, Patterson AE, et al. (1 November 2022). "Comparative property analysis of fused filament fabrication PLA using fresh and recycled feedstocks". Materials Research Express. 9 (11): 115303. Bibcode:2022MRE.....9k5303D. doi: 10.1088/2053-1591/ac96d4 . S2CID   252665567.
  63. ↑ "Chemical recycling closes the LOOPLA for cradle-to-cradle PLA". 20 November 2015.
  64. ↑ Gorrasi G, Pantani R (2017). "Hydrolysis and Biodegradation of Poly(lactic acid)". In Di Lorenzo ML, Androsch R (eds.). Synthesis, Structure and Properties of Poly(lactic acid). Advances in Polymer Science. Vol. 279. Cham: Springer International Publishing. pp. 119–151. doi:10.1007/12_2016_12. ISBN   978-3-319-64229-1.
  65. ↑ Iovino R, Zullo R, Rao MA, Cassar L, Gianfreda L (2008). "Biodegradation of poly(lactic acid)/starch/coir biocompositesunder controlled composting conditions". Polymer Degradation and Stabilit. 93: 147. doi:10.1016/j.polymdegradstab.2007.10.011.
  66. ↑ Pantani R, Sorrentino A (2013). "Influence of crystallinity on the biodegradation rate of injection-moulded poly(lactic acid) samples in controlled composting conditions". Polymer Degradation and Stability. 98 (5): 1089. doi:10.1016/j.polymdegradstab.2013.01.005.
  67. 1 2 "How long does it take for plastics to biodegrade?". HowStuffWorks. 15 December 2010. Retrieved 9 March 2021.
  68. ↑ "End of Life Options for Bioplastics – Recycling, Energy, Composting, Landfill - Bioplastics Guide | Bioplastics Guide". Archived from the original on 25 February 2021. Retrieved 9 March 2021.
  69. ↑ Chien YC, Liang C, Liu SH, Yang SH (July 2010). "Combustion kinetics and emission characteristics of polycyclic aromatic hydrocarbons from polylactic acid combustion". Journal of the Air & Waste Management Association. 60 (7): 849–855. Bibcode:2010JAWMA..60..849C. doi:10.3155/1047-3289.60.7.849. PMID   20681432. S2CID   34100178.
  70. ↑ Sun C, Wei S, Tan H, Huang Y, Zhang Y (October 2022). "Progress in upcycling polylactic acid waste as an alternative carbon source: A review". Chemical Engineering Journal. 446. Bibcode:2022ChEnJ.44636881S. doi:10.1016/j.cej.2022.136881. S2CID   248715252.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.