This article relies largely or entirely on a single source .(July 2009) |
/ D24 | |
---|---|
Overview | |
Manufacturer | Volkswagen Group |
Production | 1978–1995 |
Layout | |
Configuration | inline/row 6-cylinder (R6/I6) diesel engine |
Displacement | 2,383 cc (145.4 cu in) |
Cylinder bore | 76.5 mm (3.01 in) [1] |
Piston stroke | 86.4 mm (3.40 in) |
Cylinder block material | gray cast iron, 7 main bearings [1] |
Cylinder head material | cast aluminium alloy [1] |
Valvetrain | 12v, belt-driven single overhead camshaft (SOHC) [1] |
Compression ratio | 23.5:1 |
Combustion | |
Fuel system | Bosch mechanical distributor injection pump, indirect fuel injection [1] |
Fuel type | diesel |
Oil system | wet sump [1] |
Cooling system | water-cooled timing belt driven water pump [1] |
Output | |
Power output | 82 hp at 4800 rpm (DIN) |
Torque output | 14.3 kpm at 2800 rpm |
Dimensions | |
Dry weight | 182 kg |
Chronology | |
Successor | Volkswagen D24 engine |
The Volkswagen D24 engine is a 2.4-litre inline-six-cylinder (R6/I6), naturally aspirated diesel engine, formerly manufactured by Volkswagen Group from 1978 to 1995. [1]
Subsequent forced induction variants of this engine were also available as the Volkswagen D24T engine with a turbocharger, and a turbo intercooled version, the Volkswagen D24TIC engine. These turbocharged variants resulted in higher power and torque outputs. [1]
All variants (naturally aspirated and forced induction) displace 2,383 cubic centimetres (145.4 cu in ) from a cylinder bore of 76.48 millimetres (3.01 in), and a piston stroke of 86.4 millimetres (3.40 in). Its inline six cylinder block is constructed from grey cast iron, and has seven main bearings to support the die-forged steel crankshaft. The cast aluminium alloy cylinder head contains two valves per cylinder each with two concentric valve springs, and shim-adjustable bucket tappets. The valves are opened via a timing belt-driven single overhead camshaft (SOHC), and the combustion chamber compression ratio is 23.0:1.
Attached to the cylinder head is a cast aluminium alloy intake manifold on one side, and two cast iron exhaust manifolds on the same side (it's a non cross flow engine) (one manifold for three cylinders) followed by a two in one exhaust pipe system. The fuel system uses a Bosch mechanical distributor-type (Bosch VE type) injection pump which feeds indirect fuel injection into a remote whirl pre-combustion chamber.
The cooling system is composed of a timing belt driven water pump, an 87 °C thermostat in the engine block itself. The thermostat receives coolant from the engine block and from a bypass running from the engine head. This system allows a very accurate opening and closing operation, avoiding thermal shocks and big coolant temperatures amplitude.
The initially available variant of the D24 produced a DIN-rated power output of 55 kilowatts (75 PS ; 74 bhp ) at 4,500 rpm; and it generated a torque of 155 newton-metres (114 lbf⋅ft) at 2,800 rpm. [1] Subsequent minor updates and revisions resulted in differing power and torque ratings.
ID(s) | DIN-rated max. power at rpm | max. torque at rpm | redline (rpm) | years |
---|---|---|---|---|
1S, ACT [2] | 51 kW (69 PS; 68 bhp) at 3,400 | 145 N⋅m (107 lbf⋅ft) at 1,600-1,800 | 1988–1995 | |
CP, DW [1] | 55 kW (75 PS; 74 bhp) at 4,000 | 155 N⋅m (114 lbf⋅ft) at 2,800 | 1978–1992 | |
Volkswagen D24 | 60 kW (82 PS; 80 bhp) at 4,800 | 140 N⋅m (103 lbf⋅ft) at 2,800 | 1978-1990 | |
Volkswagen D24 | 58 kW (79 PS; 78 bhp) at 4,700 | 140 N⋅m (103 lbf⋅ft) at 2,400 | 1991-1993 | |
Volkswagen D24 T (without intercooler) | 80 kW (109 PS; 107 bhp) at 4,800 | 205 N⋅m (151 lbf⋅ft) at 2,500 | 1983-1991 | |
Volkswagen D24 TIC (with intercooler) | 90 kW (122 PS; 121 bhp) at 4,800 | 235 N⋅m (173 lbf⋅ft) at 2,400 | max rpm @5200 rpm before fuel cut | 1986-1995 |
The weight of this engine is 182 kg or 401 lbs.
The D24 was fitted in the Volkswagen LT range from Volkswagen Commercial Vehicles, with factory production from August 1978 to December 1995. [1] Specific dates of the variants - CP: 08/78-11/82, DW: 12/82-07/92, 1S: 08/88-07/92, ACT: 08/92-12/95. [1]
The D24 was also found in a number of Volvo models, specifically the 240, 740, and 940, and it was coupled to Volvo ZF, Automatic Aisin Warner AW55, Automatic Borg Warner BW55, M45, M46 (overdrive) or M47, M47 II and M90 transmissions.
The D24 also found use in military vehicle applications. It was used in the Steyr-Daimler-Puch Pinzgauer High Mobility All-Terrain Vehicle 716 & 718 models in its turbocharged variant - the D24T.
This section possibly contains original research .(July 2009) |
In service, the unit proved to be a somewhat mixed bag; some owners reported excellent reliability and long engine lives, others complained of overheating, frequent blowing of head gaskets, cylinder head cracks (cracks between the valve seats are common and do not represent danger if the cracks do not exceed specifications), premature wear of the bottom and top end bearings, low oil pressure etc.[ citation needed ]
A poorly maintained cooling system could also lead to overheating and, especially with the higher stressed turbo engines, head gasket problems. The head gasket problem has been treated with the adoption of a multi-layer steel head gasket which replaces the fiber one.
The camshaft drive belt also required changing at the recommended intervals, which was a pretty involved job, not least because of poor access in the under-floor engined LT vans, and the necessity of special (and expensive) locking tools to carry out the replacement, which have always been scarce and are becoming increasingly difficult to obtain. [3]
The top end also featured adjustable tappets using the bucket and shim arrangement, and required checking every 25,000 miles (40,000 km), although later (1990–) models had self-adjusting hydraulic tappets.
In many cases however, engines that have been looked after properly and treated with mechanical sympathy, have been known to clock up 500,000 - 600,000 miles. This engine is particularly sensitive to being thrashed from cold, it is important to go gently until warmed up, and to avoid short journeys which will exacerbate rapid engine wear.
In a piston engine, the cylinder head sits above the cylinders, forming the roof of the combustion chamber. In sidevalve engines the head is a simple plate of metal containing the spark plugs and possibly heat dissipation fins. In more modern overhead valve and overhead camshaft engines, the head is a more complicated metal block that also contains the inlet and exhaust passages, and often coolant passages, Valvetrain components, and fuel injectors.
The Volkswagen LT is the largest light commercial panel van produced by Volkswagen from 1975 to 2006, before being replaced by the Crafter. Two generations were produced.
A W8 engine is an eight-cylinder piston engine with four banks of two cylinders each, arranged in a W configuration.
The Chevrolet 2300 is a 2.3-liter straight-four engine produced by the Chevrolet division of General Motors for the 1971 to 1977 model years of the Chevrolet Vega and Chevrolet Monza. This engine was also offered in the 1973–74 Pontiac Astre, the 1975–77 Pontiac Astre, the Pontiac Sunbird for 1976 only, and the Oldsmobile Starfire for 1976–77.
The Volvo 700 series is a range of executive cars produced by the Swedish manufacturer Volvo Cars from 1982 to 1992. The 700 series was introduced in 1982 with the luxurious 760, followed two years later by the lower priced 740 which capitalized on the prestige attained by the very similar 760. The 700 series was then gradually replaced, beginning in 1990, by the 900 series. The 700, designed by Jan Wilsgaard, was originally to have been a replacement for the 200 series, but production of that model continued until the early nineties. The expensive 780, a Bertone-designed coupé version, entered production in 1986 and departed without a direct successor only four years later.
The Volkswagen G60 and G40 were inline–four-cylinder automobile petrol engines, which used a specific method of forced induction by way of a scroll-type supercharger. The G60 engine was formerly manufactured by the German automaker Volkswagen Group and was installed in a limited number of their 'hot hatch' cars from their Volkswagen Passenger Cars marque from August 1988 to July 1993.
The KV6 automotive petrol engine has a 24-valve quad-cam V6 configuration, and a pressurising variable-length intake manifold to add hot spots throughout the rev range. Variants exist in 2.0 to 2.5 litres capacities. These were built initially by Rover Group, then by Powertrain Ltd. KIA manufactured KV6 in Korea under licence. Production moved from the UK to China in 2005, re-designated NV6.
The Volvo D5 is a type of turbocharged diesel engine developed by Volvo Cars for use in its passenger cars. The D5 engine is based on the Volvo Modular diesel engine. The D5 displaces 2.4 liters; a smaller series of two-litre engines were developed in 2010 and marketed as the Volvo D3 and D4.
The following outline is provided as an overview of and topical guide to automobiles:
The OM603 engine was a straight-6 Diesel automobile engine from Mercedes-Benz used from 1984 through 1999. The 603 saw limited use in the W124, W126 and W140 model vehicles.
The Volvo 900 Series is a range of executive cars produced by the Swedish manufacturer Volvo Cars from 1990 to 1998. The 900 Series was introduced in 1990 to replace the 700 Series from which it derived. Prior to the end of its production, the 960 was renamed as the Volvo S90 (saloon) and Volvo V90 (estate), and the 940 was renamed 940 Classic, becoming the last rear-wheel-drive cars from Volvo, until the 2023 Volvo XC40.
The Volkswagen D24T engine is a 2.4-litre inline-six-cylinder (R6/I6) single overhead camshaft (SOHC) diesel engine, formerly manufactured by Volkswagen Group from December 1982 to July 1992.
The Volkswagen D24TIC is a 2.4-litre inline-six-cylinder (R6/I6) single overhead camshaft (SOHC) diesel engine, formerly manufactured by Volkswagen Group from August 1986 to December 1998.
The EA827 family of petrol engines was initially developed by Audi under Ludwig Kraus leadership and introduced in 1972 by the B1-series Audi 80, and went on to power many Volkswagen Group models, with later derivatives of the engine still in production into the 2010s. This is a very robust water-cooled engine configuration for four- up to eight- cylinders. In Brazil this engine was produced under the name Volkswagen AP AP.
The Fiat Pratola Serra modular engines are a family of engines produced by the Fiat Group since 1994 and used in Fiat, Alfa Romeo, Lancia and Jeep vehicles. They are named after the Pratola Serra municipality in which they're being produced.