Beach cusps

Last updated
A beach cusp Basic cusp.jpg
A beach cusp

Beach cusps are shoreline formations made up of various grades of sediment in an arc pattern. The horns are made up of coarser material and the embayment contains finer sediment.

Contents

They can be found all over the world and are most noticeable on shorelines with coarser sediment such as pebble beaches. However, they can occur with sediment of any size. They nearly always occur in a regular pattern with cusps of equal size and spacing appearing along stretches of the shoreline. These cusps are most often a few metres long. However, they may reach 60 m (200 ft) across. Although the origin of beach cusps has yet to be proven, once cusps have been created they are a self-sustaining formation. This is because when an oncoming wave hits the horn of a beach cusp, it is split and forced into two directions. The crashing of the wave into the cusps slows its velocity, causing coarser sediment to fall out of suspension and be deposited on the horns. The waves then flow along the embayments (picking up finer sediment) and run into one another in the middle. After this collision these waves attempt to flow back out to sea where they are met by incoming waves. Therefore, once the cusp is established, coarser sediment is constantly being deposited on the horn and finer sediment is being eroded away from the embayments. [1] This process causes the horners and embayments to at least maintain their size, if not grow larger.

Formation

There are a number of theories as to why beach cusps are formed but currently, there are only two explanations with any real credibility.

Standing edge wave theory

Standing Edge Wave Theory Nodal points.jpeg
Standing Edge Wave Theory

The standing edge wave theory is based on an interaction, near the shoreline, between the waves that are approaching the shore and waves that have been set up perpendicular to the shoreline called 'edge waves'. The regular arrival of incoming waves in the near shore waters causes the development of waves perpendicular to the direction of the incoming waves; these are termed 'edge waves'. These edge waves become trapped near the shoreline and when two of them come together from opposite directions, a standing edge wave is formed. The movement patterns of these waves are fixed and so can be defined as two regions of interest, the nodal and antinodal points.

The antinodal point is where all the movement takes place as the water rises and falls, creating a series of peaks and troughs. Between these antinodal points are the nodal points where no vertical movement takes place. An incoming wave has an almost uniform height but when it collides with a standing edge wave, this is changed. If it collides with a peak, then the wave height is increased and if it collides with a trough, then its height is decreased. In the adjacent diagram, the two waves cancel each other out, creating a flat surface. However, this is a highly simplified version of events. The incoming wave has the same wave period as the edge wave, so the incoming wave changes from a peak to a trough over the same period as it takes the standing wave to change so they keep the same pattern. These are known as synchronous waves and are very uncommon.

The more common standing edge waves are subharmonic and these can have a wave period twice that of the incoming wave. This produces a far more complex system of waves as by the time the incoming wave has completed one cycle from peak to trough, the standing edge waves have done two. So what started as the peak of a standing edge wave within the trough of the incoming wave will change to a trough before the incoming wave has changed so what was initially being given a boost in height now experiences a drop. Essentially what this means is that there are a regularly spaced series of peaks and troughs along the length on the incoming wave that are caused by its interaction with the standing edge waves and it is these that caused the development of beach cusps.

In areas where the wave height has been increased, the wave now has more power and so can erode more and in areas where the wave height has been decreased, the wave now has less power and so will not erode as much. This is what forms the cusps as the areas with high erosion become the embayments of the cusp and the areas with low erosion become the horns.

The problem with the standing edge wave theory is that it would only account for the initial formation of the cusp and not their continued growth afterwards because as the cusp increases in size the amplitude of the edge wave decreases to the point where it is no longer a factor.

Self-organization

This theory was initially dismissed due to complications with it but by using more advanced computer simulations, it has been developed to the point where it now provides a reasonable alternative to the standing edge wave theory. The theory has two main points that seek to explain the formation of regularly spaced beach cusps.

The first is that positive feedback between the morphology of the beach and the flow of the water creates relief patterns. On a flat beach, surface areas will develop with a slightly lower relief than their surroundings. Areas with lower relief attract and accelerate water particles, which means they have more energy and the area is eroded further. Through positive feedback, the area becomes more and more eroded, and this creates the embayment. The development of these areas of lower relief causes mean beach level to be lowered and so areas that were initially on the level are now below the average and as such, are now areas of higher relief. Areas of higher relief slow the water down and sediment is deposited on top of them, which increases their impact. This creates the horns.

The uniform spacing of cusps is caused by the communication of surface gradients along the beach by the smoothing of the beach surface as the beach tries to rearrange itself to reduce variations in the plane.

The second main point about the regular spacing of cusps is that negative feedback will decrease the amount of net erosion and deposition within a well-formed cusp. As the wave strikes the beach, it will first come into contact with the cusp horns, which will slow the water down. This causes it to lose energy and some of the heavier sediment that it is carrying will be deposited. The loss of this sediment, however, gives the water extra energy, and it uses this to remove sediment from the embayment on the backwash.

The problem with this theory is that this method of cusp formation would take time and if you were observing their formation, then you would see a number of random cusps form along the beach, which then slowly spread along the shore as they even out in size, with small cusps joining together and larger cusps being separated in two. But in the field, cusps form a regular pattern almost instantly and they all appear at the same time.

Field studies

Beach cusps in Westerly, Rhode Island Beach cusps at Napatree Point (52404).jpg
Beach cusps in Westerly, Rhode Island

In recent years, there has been considerable debate about whether beach cusp formation is associated with the presence of standing edge waves (standing edge wave theory), results from self-organizing feedback between changing topography and swash motion (self-organization theory) or is attributable to a number of other less popular mechanisms.

The National Centre of Scientific Research in France, collected a large amount of data from laboratory experiments and field studies, published over the last 50 years to test the predictions of the two main cusp forming hypotheses. These analyses, using more data than previous attempts, confirm that there is a possible link between cusp development and both edge waves and swash-sediment feedback, and that it is not possible to produce conclusive support for one theory above the other with the simple measurements that have been made previously. [2]

The Naval Research Laboratory, the corporate research laboratory for the United States Navy and Marine Corps carried out nearly nine years of video imagery from Duck, North Carolina to determine the timing of cusp formation (to within half a day) and the distances separating consecutive cusp horns (to within half a metre). Supplementary data provided by nearshore instrumentation and surveying vehicles was used to document the environmental conditions during cusp development.

These extensive observations conclusively demonstrate that cusps at this location develop, following storms during the transition from high energy to low energy wave conditions as the wave angle approaches normal incidence. A peculiar suggestion of hysteresis within the cusp spacing time series was observed and may suggest that existing theories of cusp formation need to be reformulated. [3]

See also

Related Research Articles

<span class="mw-page-title-main">Erosion</span> Natural processes that remove soil and rock

Erosion is the action of surface processes that removes soil, rock, or dissolved material from one location on the Earth's crust and then transports it to another location where it is deposited. Erosion is distinct from weathering which involves no movement. Removal of rock or soil as clastic sediment is referred to as physical or mechanical erosion; this contrasts with chemical erosion, where soil or rock material is removed from an area by dissolution. Eroded sediment or solutes may be transported just a few millimetres, or for thousands of kilometres.

<span class="mw-page-title-main">Beach</span> Area of loose particles at the edge of the sea or other body of water

A beach is a landform alongside a body of water which consists of loose particles. The particles composing a beach are typically made from rock, such as sand, gravel, shingle, pebbles, etc., or biological sources, such as mollusc shells or coralline algae. Sediments settle in different densities and structures, depending on the local wave action and weather, creating different textures, colors and gradients or layers of material.

<span class="mw-page-title-main">Sediment</span> Particulate solid matter that is deposited on the surface of land

Sediment is a naturally occurring material that is broken down by processes of weathering and erosion, and is subsequently transported by the action of wind, water, or ice or by the force of gravity acting on the particles. For example, sand and silt can be carried in suspension in river water and on reaching the sea bed deposited by sedimentation; if buried, they may eventually become sandstone and siltstone through lithification.

<span class="mw-page-title-main">Coastal erosion</span> Displacement of land along the coastline

Coastal erosion is the loss or displacement of land, or the long-term removal of sediment and rocks along the coastline due to the action of waves, currents, tides, wind-driven water, waterborne ice, or other impacts of storms. The landward retreat of the shoreline can be measured and described over a temporal scale of tides, seasons, and other short-term cyclic processes. Coastal erosion may be caused by hydraulic action, abrasion, impact and corrosion by wind and water, and other forces, natural or unnatural.

<span class="mw-page-title-main">Shoal</span> Natural submerged sandbank that rises from a body of water to near the surface

In oceanography, geomorphology, and geoscience, a shoal is a natural submerged ridge, bank, or bar that consists of, or is covered by, sand or other unconsolidated material, and rises from the bed of a body of water close to the surface or above it, which poses a danger to navigation. Shoals are also known as sandbanks, sandbars, or gravelbars. Two or more shoals that are either separated by shared troughs or interconnected by past or present sedimentary and hydrographic processes are referred to as a shoal complex.

Landforms are categorized by characteristic physical attributes such as their creating process, shape, elevation, slope, orientation, rock exposure, and soil type.

<span class="mw-page-title-main">Longshore drift</span> Sediment moved by the longshore current

Longshore drift from longshore current is a geological process that consists of the transportation of sediments along a coast parallel to the shoreline, which is dependent on the angle of incoming wave direction. Oblique incoming wind squeezes water along the coast, generating a water current that moves parallel to the coast. Longshore drift is simply the sediment moved by the longshore current. This current and sediment movement occurs within the surf zone. The process is also known as littoral drift.

<span class="mw-page-title-main">Barrier island</span> Coastal dune landform that forms by wave and tidal action parallel to the mainland coast

Barrier islands are a coastal landform, a type of dune system and sand island, where an area of sand has been formed by wave and tidal action parallel to the mainland coast. They usually occur in chains, consisting of anything from a few islands to more than a dozen. They are subject to change during storms and other action, but absorb energy and protect the coastlines and create areas of protected waters where wetlands may flourish. A barrier chain may extend for hundreds of kilometers, with islands periodically separated by tidal inlets. The largest barrier island in the world is Padre Island of Texas, United States, at 113 miles (182 km) long. Sometimes an important inlet may close permanently, transforming an island into a peninsula, thus creating a barrier peninsula, often including a beach, barrier beach. Though many are long and narrow, the length and width of barriers and overall morphology of barrier coasts are related to parameters including tidal range, wave energy, sediment supply, sea-level trends, and basement controls. The amount of vegetation on the barrier has a large impact on the height and evolution of the island.

<span class="mw-page-title-main">Mississippi embayment</span> Low-lying basin filled with Cretaceous to recent sediments

The Mississippi embayment is a physiographic feature in the south-central United States, part of the Mississippi Alluvial Plain. It is essentially a northward continuation of the fluvial sediments of the Mississippi River Delta to its confluence with the Ohio River at Cairo, Illinois. The current sedimentary area was formed in the Cretaceous and early Cenozoic by the filling with sediment of a pre-existing basin. An explanation for the embayment's formation was put forward by Van Arsdale and Cox in 2007: movement of the Earth's crust brought this region over a volcanic "hotspot" in the Earth's mantle causing an upthrust of magma which formed the Appalachian-Ouachita range. Subsequent erosion caused a deep trough that was flooded by the Gulf of Mexico and eventually filled with sediment from the Mississippi River.

<span class="mw-page-title-main">Ice volcano</span> Wave-driven mound of ice formed on terrestrial lakes

An ice volcano is a conical mound of ice formed over a terrestrial lake via the eruption of water and slush through an ice shelf. The process is wave-driven, with wind providing the energy for the waves to cut through the ice and create formations that loosely mimic the shape and activity of volcanoes. After being ejected into the atmosphere, the liquid water and slush freeze and fall back to the surface, growing the formation. Ice may also be erupted. The phenomenon is most often observed along the southern coast of Lake Erie and Lake Ontario, when the temperature is below freezing and the wind blows onshore with a velocity of at least 25 mph (40 km/h). They are known to reduce coastal erosion there. The formations are temporary: they are frequently destroyed by storms and warm weather, and once the lake wholly freezes over, eruptions are no longer possible.

Coastal morphodynamics refers to the study of the interaction and adjustment of the seafloor topography and fluid hydrodynamic processes, seafloor morphologies, and sequences of change dynamics involving the motion of sediment. Hydrodynamic processes include those of waves, tides and wind-induced currents. Anthropogenic climate change is causing changes in the coastal changes and processes that are interconnected with those caused by natural processes.

<span class="mw-page-title-main">Coastal management</span> Preventing flooding and erosion of shorelines

Coastal management is defence against flooding and erosion, and techniques that stop erosion to claim lands. Protection against rising sea levels in the 21st century is crucial, as sea level rise accelerates due to climate change. Changes in sea level damage beaches and coastal systems are expected to rise at an increasing rate, causing coastal sediments to be disturbed by tidal energy.

<span class="mw-page-title-main">Swash</span> A turbulent layer of water that washes up on the beach after an incoming wave has broken

Swash, or forewash in geography, is a turbulent layer of water that washes up on the beach after an incoming wave has broken. The swash action can move beach materials up and down the beach, which results in the cross-shore sediment exchange. The time-scale of swash motion varies from seconds to minutes depending on the type of beach. Greater swash generally occurs on flatter beaches. The swash motion plays the primary role in the formation of morphological features and their changes in the swash zone. The swash action also plays an important role as one of the instantaneous processes in wider coastal morphodynamics.

<span class="mw-page-title-main">Cross-bedding</span> Sedimentary rock strata at differing angles

In geology, cross-bedding, also known as cross-stratification, is layering within a stratum and at an angle to the main bedding plane. The sedimentary structures which result are roughly horizontal units composed of inclined layers. The original depositional layering is tilted, such tilting not being the result of post-depositional deformation. Cross-beds or "sets" are the groups of inclined layers, which are known as cross-strata.

<span class="mw-page-title-main">Cuspate foreland</span> Geographical features found on coastlines and lakeshores

Cuspate forelands, also known as cuspate barriers or nesses in Britain, are geographical features found on coastlines and lakeshores that are created primarily by longshore drift. Formed by accretion and progradation of sand and shingle, they extend outwards from the shoreline in a triangular shape.

Beach evolution occurs at the shoreline where sea, lake or river water is eroding the land. Beaches exist where sand accumulated from centuries-old, recurrent processes that erode rocky and sedimentary material into sand deposits. River deltas deposit silt from upriver, accreting at the river's outlet to extend lake or ocean shorelines. Catastrophic events such as tsunamis, hurricanes, and storm surges accelerate beach erosion.

<span class="mw-page-title-main">Sedimentary budget</span>

Sedimentary budgets are a coastal management tool used to analyze and describe the different sediment inputs (sources) and outputs (sinks) on the coasts, which is used to predict morphological change in any particular coastline over time. Within a coastal environment the rate of change of sediment is dependent on the amount of sediment brought into the system versus the amount of sediment that leaves the system. These inputs and outputs of sediment then equate to the total balance of the system and more than often reflect the amounts of erosion or accretion affecting the morphology of the coast.

<span class="mw-page-title-main">Geology of Cape Town</span> Geological formations and their history in the vicinity of Cape Town

Cape Town lies at the south-western corner of the continent of Africa. It is bounded to the south and west by the Atlantic Ocean, and to the north and east by various other municipalities in the Western Cape province of South Africa.

<span class="mw-page-title-main">Canterbury Bight</span> Oceanic bight in Canterbury, New Zealand

The Canterbury Bight is a large bight on the eastern side of New Zealand's South Island. The bight runs for approximately 135 kilometres (84 mi) from the southern end of Banks Peninsula to the settlement of Timaru and faces southeast, exposing it to high-energy storm waves originating in the Pacific Ocean. The bight is known for rough conditions as a result, with wave heights of over 2 metres (6.6 ft) common. Much of the bight's geography is shaped by this high-energy environment interacting with multiple large rivers which enter the Pacific in the bight, such as the Rakaia, Ashburton / Hakatere, and Rangitata Rivers. Sediment from these rivers, predominantly Greywacke, is deposited along the coast and extends up to 50 kilometres (31 mi) out to sea from the current shoreline. Multiple hapua, or river-mouth lagoons, can be found along the length of the bight where waves have deposited sufficient sediment to form a barrier across a river mouth, including most notably Lake Ellesmere / Te Waihora and Washdyke Lagoon

<span class="mw-page-title-main">Hapua</span>

A hapua is a river-mouth lagoon on a mixed sand and gravel (MSG) beach, formed at the river-coast interface where a typically braided, although sometimes meandering, river interacts with a coastal environment that is significantly affected by longshore drift. The lagoons which form on the MSG coastlines are common on the east coast of the South Island of New Zealand and have long been referred to as hapua by Māori people. This classification differentiates hapua from similar lagoons located on the New Zealand coast termed waituna.

References

  1. Easterbrook, Don J. Surface Processes and Landforms. Second Edition. Prentice Hall. 1999. 447-448 pp.
  2. INIST-CNRS webpage
  3. Beach Cusp Formation and Spacings at Duck, NC Archived March 11, 2007, at the Wayback Machine