Boeing-Canada A-213 Totem

Last updated

A-213 Totem
AL61A-453 Boeing A-213 Totem CF-ARF.jpg
RoleUtility and fisheries seaplane
National origin Canada
Manufacturer Boeing Aircraft of Canada
DesignerCaptain Edward Fothergill Elderton
First flightJune 1932 [1]
Introduction1932
StatusScrapped in 1942
Primary users Canadian Airways
Boeing Aircraft of Canada
Number built1
Boeing-Canada Totem on hoist Boeing Aircraft Co. of Canada Totem flying boat CF-ARF on hoist rear.jpg
Boeing-Canada Totem on hoist

The Boeing-Canada A-213 Totem was a Canadian single-engine pusher monoplane flying boat intended for forestry and fisheries patrols as well as a light utility transport for the British Columbia coastline, where there are few flat places for runways, and waterways are plentiful. The sole example, CF-ARF, CB10 [2] was designed and built by Boeing Aircraft of Canada. The name refers to the Totem poles used by the First Nations in British Columbia. [3]

Contents

Design

Boeing-Canada A-213 Totem taxiing across the water Boeing-Canada A-213 Totem taxiing across water.jpg
Boeing-Canada A-213 Totem taxiing across the water

The Chief Engineer, Edward Fothergill Elderton was British, and had previously worked at Short Brothers [4] and Saunders-Roe before coming to Canada to work for Canadian Vickers and Boeing of Canada. [3]

Despite being developed while the Boeing 40H-4 and C-204 were under construction, the Totem's design owed little to Boeing aside from the Boeing 103 airfoil section and the rudder shape. [3] Indeed, previous Boeing flying boats used wood extensively in the hull, and the 40H-4 used welded steel tubes for its fuselage structure. Instead, its tumblehome and heavy external ribs on the hull showed a strong Saunders-Roe influence, which is unsurprising given the Chief Engineer's background. [3] The model number A-213 fits numerically in the Boeing sequence but the significance of the 'A' prefix remains unexplained. [3] It may be a coincidence that Saunders-Roe was using an A as a prefix for all their aircraft at that time.

The bottom of the hull was built up as a three-ply Alclad sandwich, riveted to frames with external longitudinal stringers. The sides and top of the hull used sheet metal with widely spaced corrugations or ribs. [4] There were five bulkheads separating six watertight compartments, and it made extensive use of stainless steel components to limit corrosion. [4] The roomy 4 seat cabin was positioned ahead of the front wing spar and was accessed through a folding roof hatch. [4] [3] Dual controls were offered, while the stick could be removed on the passenger side. [4] The main fuel tank was behind the cabin and between the wing spars, with a smaller fuel tank in the engine nacelle that was fed by a fuel pump. [4] The Wasp Jr. radial engine was mounted as a pusher, which made passenger egress safer, and reduced cabin noise. [4] Starting was accomplished with an inertial hand starter. [4]

The wings were built around two spruce spars, with ribs and leading and trailing edges in spot welded chromium-molybdenum alloy (chrome-moly) steel, all covered in fabric sealed and tightened with aircraft dope. [4] The wings were braced with parallel steel struts to the hull chines, and fitted with metal tip floats. The high mounted elevators, fin and rudder were like the ribs, made up from spot welded chrome-moly steel, covered in fabric. [4] All controls were actuated via push-pull rods, with no cables or pulleys to jam. [4] Unusually for the time, a retractable water rudder was fitted that would pivot back and up if it struck an obstacle. [4]

Operational history

The sole Totem built, serial number CB10 was registered as CF-ARF. [2] The first known flight is believed to have been on 16 June 1932, by William J. Holland. [3] Test flights were being made in July by company pilots, and on September 25, an official test flight was made, with government observers. [3] One of the test flights was to Garibaldi Lake, the first visit by an airplane to that lake, at an altitude of 4,869 ft (1,484 m) where it experienced no difficulties.

Boeing of Canada had been having difficulty selling its flying boats, and the Totem was no exception, with it remaining in Boeing's hands for almost a year before being sold to a private operator. [5]

The Totem while with its final owner. Boeing A-213 Totem flying boat CF-ARF of Mr. W.J. Dyson.jpg
The Totem while with its final owner.

In May 1933, the Victoria Daily Times reported that Holland was taking the president of United Aircraft and Transport Corporation, (part owner of both Boeing and Boeing of Canada) for a "leisurely" flight up the British Columbia coastline to Juneau, Alaska. [6] In July 1933, Holland took the Totem to Amethyst Lake in Jasper National Park, to Lake Louise in Banff National Park and to Lake Minnewanka. [5] He gave joyrides to the locals for $5 a flight, while also occasionally doing local charters, including taking the manager of the Banff Springs Hotel to the Columbia Icefield and another longer one for a group of fishermen to Marvel Lake (north of Marvel Peak). [5] The Totem was not the first aircraft to visit Banff though, as they were preceded by a Norman Thompson N.T.2B flying boat operated by the Rocky Mountain Aviation Transport Company between 1921 and 1924. [5] Holland was notified in August that the Totem had been sold and to make haste back to Vancouver to transfer the airplane to the new owner. [5]

The new owner only kept it for a couple of years before selling it to Canadian Airways in May 1935. [7] This was despite demonstrating excellent water and flight handling characteristics during official tests and in operational service. [3] It would remain in service until January 1938, mainly carrying out fisheries patrols, [3] until they sold it to another private operator in 1938. [7] Its registration was cancelled in February 1942, and presumably scrapped. [7] [3]

The Totem served most of its career in British Columbia, however it would remain a one-off as pure-flying boats were by then being supplanted by floatplanes. [3]

Operators

Canadian Red Ensign (1921-1957).svg  Canada

Specifications (Boeing A-213 Totem)

Boeing Totem drawing Boeing-Canada A-213 Totem 3 view colour drawing.jpg
Boeing Totem drawing

Data from Flight, 1932, p.890-892

General characteristics

Performance

See also

Aircraft of comparable role, configuration and era

Related Research Articles

Bombardier Challenger 600 series Business jet family by Canadair, later Bombardier

The Bombardier Challenger 600 series is a family of business jets developed by Canadair after a Bill Lear concept, and then produced from 1986 by its new owner, Bombardier Aerospace. At the end of 1975, Canadair began funding the development of LearStar 600, and then bought the design for a wide-cabin business jet in April 1976. On 29 October, the programme was launched, backed by the Canadian federal government, and designed to comply with new FAR part 25 standards.

Short Sarafand

The Short S.14 Sarafand was a British biplane flying boat built by Short Brothers. It was planned as a general reconnaissance aircraft for military service. When it was built in 1932 it was the largest aeroplane in the United Kingdom.

Felixstowe F5L

The twin-engine F5L was one of the Felixstowe F series of flying boats developed by John Cyril Porte at the Seaplane Experimental Station, Felixstowe, England, during the First World War for production in America.

Canadian Vickers Vedette

The Canadian Vickers Vedette was the first aircraft designed and built in Canada to meet a specification for Canadian conditions. It was a single-engine biplane flying boat purchased to meet a Royal Canadian Air Force (RCAF) demand for a smaller aircraft than the Vickers Viking with a much greater rate of climb, to be suitable for forestry survey and fire protection work. The type went on to have a long and distinguished career in civil operations in Canada. Most of the topographical maps in use in Canada today are based on photos taken from these aircraft.

Canadian Vickers Varuna

The Canadian Vickers Varuna was a Canadian flying boat of the 1920s built by Canadian Vickers as a twin-engined, unequal-span biplane, with a wooden hull and steel tube structure.

Savoia-Marchetti SM.78

The Savoia-Marchetti SM.78 was an Italian bomber/reconnaissance biplane flying boat of the early 1930s.

Curtiss HS

The Curtiss HS was a single-engined patrol flying boat built for the United States Navy during World War I. Large numbers were built from 1917 to 1919, with the type being used to carry out anti-submarine patrols from bases in France from June 1918. It remained in use with the US Navy until 1928, and was also widely used as a civil passenger and utility aircraft.

Felixstowe Fury

The Felixstowe F.4 Fury, also known as the Porte Super-Baby, was a large British, five-engined triplane flying-boat designed by John Cyril Porte at the Seaplane Experimental Station, Felixstowe, inspired by the Wanamaker Triplane/Curtiss Model T. At the time the Fury was the largest seaplane in the world, the largest British aircraft, and the first aircraft controlled successfully by servo-assisted means.

The Fokker B.I was a reconnaissance flying boat built in the Netherlands in 1922. The B.I was followed by an improved version, the B.III in 1926. It was a conventional biplane flying boat design, with staggered sesquiplane wings braced by struts arranged as a Warren truss. The engine was mounted pusher-wise on the top wing. The duralumin hull featured three open cockpits - one at the nose for a gunner, one in front of the lower wing for the pilot and engineer and one behind the wings for another gunner. The B.I was amphibious, equipped with main undercarriage that folded back along the hull, but this feature was omitted in the B.III. The B.I was flown in the Dutch East Indies by the Naval Air Service for a number of years, and although it gave good service, no further examples were ordered from Fokker.

Fokker F-11

The Fokker F-11 was a luxury flying boat produced as an 'air yacht' in the United States in the late 1920s. Technically the aircraft was the Fokker Aircraft Corporation of America's Model 9. It was sold in North America as the Fokker F-11 and was offered in Europe as the Fokker B.IV. By the time the first six aircraft had been constructed, it was already evident that the design was not going to sell well. A few were sold, two to notable multi-millionaires; Harold Vanderbilt and Garfield Wood each purchasing one. One was bought by Air Ferries in San Francisco. The F-11A cost $40,000 but the price was slashed to $32,500 as the depression set in during 1930. The F-11 was a commercial failure.

General Aviation PJ

The General Aviation PJ was a flying boat produced in the United States in the 1930s as a search-and-rescue aircraft for the Coast Guard.

Boeing Model 6D Seaplane by Boeing

The Boeing Model 6D, a.k.a. Boeing Model 6E, Boeing B-1D and Boeing B-1E, was an American pusher biplane flying-boat built by Boeing between 1928 and 1929.

Zeppelin-Lindau Rs.I

The Zeppelin-Lindau Rs.I was a large three-engined biplane flying boat designed by Claudius Dornier and built during 1914–15 on the German side of Lake Constance. It never progressed beyond taxiing trials as it was destroyed in a storm.

Fairey N.4

The Fairey N.4 was a 1920s British five-seat long range reconnaissance flying boat. Designed and built by the Fairey Aviation Company to meet an Admiralty requirement for a very large four-engined reconnaissance aircraft, it was the world's biggest flying boat when it first flew in 1923.

Zeppelin-Lindau Rs.II

The Zeppelin-Lindau Rs.II was a biplane flying boat, designed by Claudius Dornier and built during 1914–1915 on the German side of Lake Constance. Initially this aircraft was powered by three engines mounted inside the hull driving three pusher propellers via gearboxes and shafts. The later version was powered by four engines in two push-pull nacelles mounted between the wings.

Peel Z-1 Glider Boat American glider

The Peel Z-1 Glider Boat, also called the Peel Flying Boat, is an American biplane, two-seats-in-tandem, flying boat glider that was designed and produced by the Peel Glider Boat Company, starting in about 1930.

The Aeromarine AMC was the first American all-metal hulled commercial flying boat.

The Aeromarine EO was a light sport flying boat that was built in the mid-1920s.

Savoia-Marchetti SM.80

The Savoia-Marchetti SM.80 was a two-seat monoplane amphibian tourer, with a single, tractor engine mounted above the wing, designed in Italy in the early 1930s. The SM.80bis was a four-seat variant, powered by two pusher engines.

Albatros L.71

The Albatros L.71 was a two-seat, single pusher engined biplane built in Germany in the 1920s.

References

Citations

  1. ↑ Milberry, 1997, p.90
  2. 1 2 Pentland, 2010, p.2
  3. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Visschedijk, 2011
  4. 1 2 3 4 5 6 7 8 9 10 11 12 Spooner, 23 September 1932, pp.890-892
  5. 1 2 3 4 5 Stokalko, 2019
  6. ↑ Victoria Daily Times, 19 May 1933, p.24
  7. 1 2 3 Aviation History Canada, 2020

Bibliography

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.