LNER Class U1

Last updated

LNER Class U1
2395 LNER U1 Garratt official photo.jpg
No. 2395, in photographic grey, in 1925
Type and origin
Power typeSteam
Designer Nigel Gresley
Builder Beyer, Peacock and Company
Serial number6209
Build date1925
Total produced1
Specifications
Configuration:
   Whyte 2-8-0+0-8-2
   UIC 1'D(D1')h6
Gauge 4 ft 8+12 in (1,435 mm) standard gauge
Leading dia. 2 ft 8 in (0.813 m)
Driver dia.4 ft 8 in (1.422 m)
Length87 ft 3 in (26.59 m)
Loco weight178 long tons (181 t; 199 short tons)
Fuel type Coal
Fuel capacity7 long tons (7.1 t; 7.8 short tons)
Water cap.5,000 imp gal (23,000 L; 6,000 US gal)
Firebox:
  Grate area56.5 sq ft (5.25 m2)
Boiler pressure180 lb/sq in (13 kg/cm2; 1,200 kPa)
Cylinders 6 (2 outside and 1 inside at each end)
Cylinder size 18+12 in × 26 in (470 mm × 660 mm)
Valve gear
Performance figures
Tractive effort 72,940 lbf (324,500 N)
Career
Operators London and North Eastern Railway
British Railways
Class LNER: U1
Locale North Eastern Region
Retired1955
Disposition Scrapped

The London and North Eastern Railway Class U1 was a solitary 2-8-0+0-8-2 Garratt locomotive designed for banking coal trains over the Worsborough Bank, [lower-roman 1] a steeply graded line in South Yorkshire and part of the Woodhead Route. It was both the longest and the most powerful steam locomotive ever to run in Britain. It was built in 1925 with the motion at each end being based on an existing 2-8-0 design. The original number was 2395, and it was renumbered 9999 in March 1946, and then 69999 after nationalisation in 1948, although it retained its cab-side plate bearing its original number throughout its life. The locomotive ran for some time as an oil burner, and was tried out on the Lickey Incline in 1949–1950 and again, after the electrification of its home line, in 1955. These trials were unsuccessful, and so the locomotive was withdrawn in 1955 and scrapped.

Contents

Origins

The Worsborough Bank, sometimes referred to as the Worsborough Incline, was a steep bank on the Great Central Railway (GCR) freight-only line from Wath to Penistone, climbing for 7 miles (11 km), with a stretch of 3 miles (4.8 km) at a nominal gradient of 1 in 40 (2.5%). Sections of this incline also suffered from colliery subsidence, making it infamously difficult to restart a stalled train on these severe sections. The main traffic on the line was loaded trains carrying coal from the South Yorkshire coalfields to Lancashire. The GCR had considered several options for banking these heavy trains, including one based on a design by Kitson and Company for a locomotive carrying out similar duties in Ceylon (now Sri Lanka). [1] This idea had been discarded due to the restricted loading gauge, and thought had turned to an articulated Garratt locomotive based on two GCR 8K 2-8-0s (LNER Class O4) with a specially designed large boiler. However, no move had been made to build such a locomotive by the time the GCR was absorbed into the LNER in the 1923 grouping, and responsibility for locomotive design passed to the Chief Mechanical Engineer of the newly formed railway, Nigel Gresley.

The design proposed by Nigel Gresley for a locomotive to bank heavy coal trains up the Worsborough bank was for a 2-8-0+0-8-2 Garratt locomotive based on two GNR O2 2-8-0s. Beyer, Peacock and Company of Manchester tendered £21,000 for the construction of two such locomotives, although the order was subsequently amended to just a single loco [2] which was delivered in summer 1925 at a cost of £14,895. The loco, works number 6209, took just three weeks from laying the frames to completion and was hurriedly sent, still in workshop grey, to appear in the centenary celebration of the Stockton & Darlington Railway where it was exhibit number 42. It was then finished in LNER black livery and was officially accepted into LNER stock in August 1925. [3]

Operation

The U1, numbered 2395, was initially allocated to Barnsley shed but due to the restricted layout there was transferred to Mexborough on 17 October 1925. [2] The locomotive was used to bank heavy trains up the Worsborough Bank, making up to 18 return trips each day; [1] a typical train consisted of an LNER Class O4 locomotive with 60+ loaded coal wagons then an assisting engine at the rear, usually another O4 or an Ex-GCR Class 1B, and finally the U1. The U1 was attached at Wentworth Junction at the bottom of the bank, and pushed for the 3+12 miles (5.6 km) to West Silkstone Junction at the top where it would be detached, while the assisting engine would normally continue as far as Dunford Bridge. Prior to the introduction of the U1 a further two O4 locos would have been used for this work [3] although the additional effort required to operate such a large locomotive as the U1 was not appreciated by the crew; "Twice the work but the same sodding pay" summing up their opinion. [1]

With its huge size and 79 ft 1 in (24.10 m) wheelbase, the U1 rode well and a commodious cab was provided. Unfortunately, this did not help when negotiating the two Silkstone tunnels just before the top of the Worsborough Bank. Being the last of three steam locos to enter the tunnel, the atmosphere on the footplate with heat, steam and smoke was "close to hell". [1] To try to overcome this, gas masks were provided for the crew connected via a pipe to a vent at rail level, but the crews objected to sharing these for reasons of hygiene [3] and continued to use the time-honoured method of covering the nose and mouth with a wet handkerchief. [1]

The locomotive itself was adequate but not successful enough for further development, and drawings for a revolving coal bunker made by Beyer, Peacock in 1930 were not pursued. [1] Indeed, the design did have some expensive flaws; soft water resulted in the boiler being retubed in 1926, [4] firebox damage was diagnosed in 1927 and 1928, and the loco was out of service for nine months during 1930 [3] during which time some modifications were carried out [1] and a new firebox fitted. [2] After this the loco itself settled down to working its regular beat up and down Worsborough Bank, despite continued steaming problems and a definite susceptibility to poor quality coal. It was renumbered 9999 in the LNER renumbering scheme of 1946, and became 69999 on the creation of British Railways in 1948.

Later life

No. 69999 on the Lickey Incline 1949 Lickey Incline 2 LNER Garratt geograph-2382157-by-Ben-Brooksbank.jpg
No. 69999 on the Lickey Incline 1949

With the electrification of the Woodhead route and the Worsborough Bank using 1500 V DC overhead catenary, and the boiler considered to be nearing the end of its useful life, [2] the continued operation of the U1 was in some doubt in the late 1940s, but in 1949 it was decided to try the U1 on the Lickey Incline on the Ex-LMS Bristol-Birmingham route to supplement the existing 0-10-0 banker nicknamed "Big Bertha". Initially it worked chimney-first, but after difficulty in buffering up to passenger trains, it was turned to run cab-first up the bank and an electric headlight was fitted. Despite this the crew had great problems with visibility from the cab, particularly after dark, and the U1 returned to Mexborough in November 1950 and was officially placed in storage there.

In February 1951, the U1 was again banking on the Worsborough Bank and continued doing so into 1952 then was briefly placed in store before being sent to Gorton Locomotive Works for work in preparation for a return to the Lickey Incline. It stayed at Gorton for three years while several different attempts were made to convert it to oil burning [1] and an improved electric headlight was also fitted. In June 1955, it resumed work on the Lickey Incline, but was stored at Bromsgrove on 13 September [2] and returned to Gorton the following month. It was officially withdrawn on 23 December 1955, [2] and was subsequently taken to Doncaster Works and cut up during early 1956, having travelled around 425,000 miles (684,000 km) during its 30 years. [3]

See also

Further reading

Related Research Articles

John George Robinson CBE, was an English railway engineer, and was chief mechanical engineer of the Great Central Railway from 1900 to 1922.

<span class="mw-page-title-main">MR 0-10-0 Lickey Banker</span>

In 1919, the Midland Railway built a single 0-10-0 steam locomotive, No 2290. It was designed by James Anderson for banking duties on the Lickey Incline in Worcestershire, England. It became known as "Big Bertha" or "Big Emma" by railwaymen and railway enthusiasts.

<span class="mw-page-title-main">Lickey Incline</span> Steep rail incline in England

The Lickey Incline, south of Birmingham, is the steepest sustained main-line railway incline in Great Britain. The climb is a gradient of 1 in 37.7 for a continuous distance of two miles (3.2 km). Constructed originally for the Birmingham and Gloucester Railway (B&GR) and opened in 1840 it is located on the Cross Country Route between Barnt Green and Bromsgrove stations in Worcestershire.

<span class="mw-page-title-main">LMS Garratt</span>

The London, Midland and Scottish Railway (LMS) Garratt was a class of Garratt 2-6-0+0-6-2 steam locomotive designed for heavy freight. A total of 33 were built from 1927, making them the most numerous class of Garratt in Britain.

<span class="mw-page-title-main">GCR Class 8K</span>

The Great Central Railway (GCR) Class 8K 2-8-0 is a class of steam locomotive designed for heavy freight. Introduced in 1911, and designed by John G. Robinson, 126 were built for the GCR prior to the First World War. Including wartime construction for the British Army ROD and the post-war GCR Class 8M, the class and its derivatives totalled 666 locomotives.

<span class="mw-page-title-main">LNER Class O4</span>

The London and North Eastern Railway (LNER) Class O4 initially consisted of the 131 ex-Great Central Railway (GCR) Class 8K 2-8-0 steam locomotives acquired on grouping in 1923. The engines were designed by John G. Robinson and built at the GCR's Gorton Locomotive Works, Manchester.

<span class="mw-page-title-main">LNER Gresley Classes A1 and A3</span> Class of 4-6-2 pacific locomotive designed by Sir Nigel Gresley

The London and North Eastern Railway Gresley Classes A1 and A3 locomotives represented two distinct stages in the history of the British 4-6-2 "Pacific" steam locomotives designed by Nigel Gresley. They were designed for main line passenger services and later express passenger services, initially on the Great Northern Railway (GNR), a constituent company of the London and North Eastern Railway after the amalgamation of 1923, for which they became a standard design. The change in class designation to A3 reflected the fitting to the same chassis of a higher pressure boiler with a greater superheating surface and a small reduction in cylinder diameter, leading to an increase in locomotive weight. Eventually all of the A1 locomotives were rebuilt, most to A3 specifications, but no. 4470 was completely rebuilt as Class A1/1.

<span class="mw-page-title-main">British Rail Class 76</span> Electric Bo-Bo locomotive

The British Rail Class 76, also known as Class EM1, is a class of 1.5 kV DC, Bo+Bo electric locomotive designed for use on the now-closed Woodhead Line in Northern England.

<span class="mw-page-title-main">LNER Peppercorn Class A2</span> Class of 15 British 4-6-2 locomotives

The London and North Eastern Railway (LNER) Peppercorn Class A2 is a class of steam locomotive designed for express passenger work by Arthur Peppercorn, the chief designer of the LNER after Edward Thompson. All save the first of the 15 built were constructed under British Railways after nationalisation in 1948. Only one example is preserved.

<span class="mw-page-title-main">GCR Class 9F</span> British steam locomotive

The Great Central Railway (GCR) Class 9F was a class of 0-6-2T steam locomotive built between 1891 and 1901. From 1923 the locomotives were redesignated Class N5.

The Manchester–Sheffield–Wath electric railway was an electrification scheme on British railways. The route featured long ascents on both sides of the Pennines with the long Woodhead Tunnel at its central summit close to the Woodhead pass. This led to the route being called the Woodhead Line.

<span class="mw-page-title-main">2-8-0+0-8-2</span> Garratt locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives by wheel arrangement, the 2-8-0+0-8-2 is a Garratt locomotive. The wheel arrangement is effectively two 2-8-0 locomotives operating back to back, with the boiler and cab suspended between the two power units. Each power unit has a single pair of leading wheels in a leading truck, followed by four coupled pairs of driving wheels and no trailing wheels.

<span class="mw-page-title-main">ROD 2-8-0</span> British locomotives built for World War I

The Railway Operating Division (ROD) ROD 2-8-0 is a type of 2-8-0 steam locomotive which was the standard heavy freight locomotive operated in Europe by the ROD during the First World War.

<span class="mw-page-title-main">Mexborough engine shed</span>

Mexborough engine shed was an engine shed in Swinton, in South Yorkshire, England. It was built by the Great Central Railway and opened in 1875. The shed was built slightly to the west of the current Mexborough station on land between the River Don and the River Don Navigation. It had 15 dead end roads, and could handle about 150 steam locomotives, mainly for use on freight trains. The London and North Eastern Railway operated the shed from 1923. In 1948, on the formation of British Railways Eastern Region, Mexborough bore the shed code 36B, then 41F from 1958. It closed in February 1964.

<span class="mw-page-title-main">NER Class X</span>

The NER Class X was a class of 4-8-0T tank locomotive designed by Wilson Worsdell for the North Eastern Railway. They were intended for use as powerful shunting engines to arrange and move coal wagons for loading into ships. In total 15 were built, 10 by the NER between 1909 and 1910, and a further five in 1925 by the London and North Eastern Railway (LNER). They had three cylinders with divided drive: the inside cylinder driving the leading axle, the outside cylinders driving the centre.

<span class="mw-page-title-main">GCR Class 8A</span>

The Great Central Railway (GCR) Class 8A was a class of 0-8-0 steam locomotive built between 1902 and 1911 for handling heavy coal trains over the Pennines. They all passed to the LNER in 1923, who redesignated them Class Q4. They were withdrawn from service between 1934 and 1951.

GCR Classes 8D and 8E were two pairs of three-cylinder compound steam locomotives of the 4-4-2 wheel arrangement built in 1905 and 1906 for the Great Central Railway.

<span class="mw-page-title-main">GCR Class 9A</span>

The Great Central Railway (GCR) Class 9A was a class of 0-6-2T steam locomotive built between 1889 and 1892. From 1923 the locomotives were redesignated Class N4.

GCR Class 8G was a class of 10 two-cylinder steam locomotives of the 4-6-0 wheel arrangement built in 1906 for the Great Central Railway.

<span class="mw-page-title-main">GCR Class 9P</span>

GCR Class 9P was a design of four-cylinder steam locomotive of the 4-6-0 wheel arrangement built for hauling express passenger trains on the Great Central Railway in England. A total of six were built: one in 1917, and five in 1920. They were sometimes known as the Lord Faringdon class, from the name of the first one built.

References

  1. The railway preserved the archaic spelling of 'Worsborough', although the town of Worsbrough has since dropped the 'o'.
  1. 1 2 3 4 5 6 7 8 Nixon, Les (30 November – 28 December 2007). "The Beast of Worsborough". Steam Railway. No. 343. Peterborough: EMAP. pp. 82–85.
  2. 1 2 3 4 5 6 "LNER Beyer-Garratt". www.thewoodheadsite.org.uk. Archived from the original on 27 September 2007. Retrieved 3 October 2008.
  3. 1 2 3 4 5 Marsden, Richard. "The U1 Garratt ('The Wath Banker')". The LNER Encyclopaedia. Retrieved 3 October 2008.
  4. Boddy, M.G.; Brown, W.A.; Fry, E.V.; Hennigan, W.; Hoole, Ken; Manners, F.; Neve, E.; Platt, E.N.T.; Proud, P.; Yeadon, W.B. (June 1977). Fry, E.V. (ed.). Locomotives of the L.N.E.R., part 9B: Tank Engines - Classes Q1 to Z5. Kenilworth: RCTS. p. 39. ISBN   0-901115-41-X.