Speaking tube

Last updated

A speaking tube in use on a United States Navy Landing Craft Utility (2005) Voice tube.jpg
A speaking tube in use on a United States Navy Landing Craft Utility (2005)

A speaking tube or voicepipe is a device based on two cones connected by an air pipe through which speech can be transmitted over an extended distance.

Contents

Use of pipes was suggested by Francis Bacon in the New Atlantis (1672). The usage for telecommunications was experimented and proposed for administrative communications in 1782 by the French monk Dom Gauthey in a memorandum communicated to the Académie des Sciences. Dom Gauthey launched a subscription supported by Benjamin Franklin and other French scientists to finance further experiments, but was not able to raise enough money to go ahead. The British utilitarist philosopher Jeremy Bentham proposed the inclusion of "conversation tubes" in the architecture of his Panopticon (1787, 1791, 1811) and then as a means of military telecommunication (1793) and at the end as a necessary equipment in the architecture of ministries (1825).

While its most common use was in intra-ship communications, the principle was also used in affluent homes and offices of the 19th century, as well as expensive automobiles, military aircraft, and even locomotives. For most purposes, the device was outmoded by the telephone and its widespread adoption.

Design

Le Petit Journal, 21 August 1910. French air-force ready to deter hostile advances along the eastern frontier, and equipped with intercom - two speaking tubes for full duplex send and receive. 1910 aircraft intercom - Two tubes for duplex send and receive.jpg
Le Petit Journal , 21 August 1910. French air-force ready to deter hostile advances along the eastern frontier, and equipped with intercom - two speaking tubes for full duplex send and receive.

Early voicepipes consisted of two cones, of wood or metal, one end shaped to fit the speaker's mouth, connected to the other which was flared to amplify the sound (specifically to match the impedance of the tube to that of the open room). Later designs of the voicepipe inserted a removable cork-mounted whistle, which could be sounded by blowing into the tube from the other end. On naval vessels, this created a distinctive sound associated with urgent intra-ship communication. The sound of the whistle would summon the listener, who would remove the whistle and answer the call.

Voice pipes could be used over distances as long as 300 feet (90 m). [1] However, very long speaking tubes might use an electrical signalling device to indicate a call, as the large volume of air in the pipe would make it difficult to blow with enough pressure to sound a whistle at the far end. [1] Despite this, a pipe with a larger internal diameter was desirable for longer runs as the signal loss is inversely proportional to the pipe's cross-sectional area. [1]

Voicepipes have no switching mechanism and so, to provide multiple destinations, separate voicepipes with dedicated transit pipes have to be provided between all pairs of desired endpoints.

The technology continues to be used into the electronic age due to its reliability and low cost. Voice pipes are unaffected by a complete electrical power loss or by an electromagnetic pulse. Warships built as late as the 1950s continued to incorporate voicepipes alongside more advanced technology.[ citation needed ]

Maritime use

British warship officer with mounted binoculars and two speaking tubes The Royal Navy during the Second World War A3878.jpg
British warship officer with mounted binoculars and two speaking tubes

Voice pipes, the maritime term, served to transmit reports from lookout positions aloft to the deck and from the bridge to the steering position and engine room. These were somewhat larger in diameter than the domestic version and were often covered in sound absorbent material to increase their efficiency.

Copper voice pipes were being fitted to British two and three-deck warships as early as 1803. A notable use was on board HMS Victory at the Battle of Trafalgar in 1805. Victory's ship's wheel was shot away early in the battle. A voice tube was then used to carry steering orders from the quarterdeck down three decks, to where a gang of sailors operated the ship's tiller directly using ropes and pulleys. [2]

One disadvantage of voice pipes is that they may breach the integrity of watertight spaces. This led to the introduction of shut-off valves on both ends of voicepipes to prevent water from a flooded compartment from entering other compartments via its voicepipes.

Permanently fitted, rigid voice pipes are still in use and are generally covered with heavy lids to avoid ingress of water. The speaker has to place his mouth in the "horn" or bell-shaped end of the pipe and the receiver has to 'bend an ear' to hear what is being said.

Voice pipes have generally been replaced by sound-powered telephones. The speaking tubes on naval ships are used when they are in "clam" mode[ clarification needed ] instead of telephones for electronic stealth.[ citation needed ]

Domestic use

An office in 1903, showing speaking tubes hanging on the end of a desk Office speaking tubes 1903.jpg
An office in 1903, showing speaking tubes hanging on the end of a desk
Domestic speaking tube on the sidewalk end. Brussels,(2014) Caption is Please listen to the voice-carrier. Parlophone pneumatique.jpg
Domestic speaking tube on the sidewalk end. Brussels,(2014) Caption is Please listen to the voice-carrier.

In domestic applications, voicepipes were smaller and referred to as "speaking tubes". The ends of the tube were often flexible for convenience of use. The speaking tube supplemented the array of remotely controlled hand bells that were operated in the upstairs rooms and rang in the servant's quarters in even modest houses in the 19th century. The phrase "get on the horn" and "give him a blow" as well as the use of "blower" as a synonym for "telephone" are generally accepted as having their origin in this feature of speaking tubes.[ citation needed ]

Speaking tubes were employed in some offices, with whistles at either end and were therefore also known as whistling tubes. [3] Several speaking tubes could be hung from the edge of a desk to communicate with different locations.

Speaking tubes were also used in fine automobiles, such as the 1927 Rolls-Royce Phantom, allowing communication between the separate passenger and driver's compartments when desired.

Gosport tube

A 'Gosport Tube' was a voice tube used by flight instructors in the early days of military aviation to give instructions and directions to their students. It was invented by flying instructor Robert Raymond Smith-Barry at the School of Special Flying he opened at Gosport in 1917. [4]

Modern usage

Acoustic tube headphones (also called pneumatic earphones or air earphones) are used especially in two-way radio. These are useful because a clear tube can be used to hide the earphones. They are also sometimes used for the microphone on telephonists headsets and to provide music to patients undergoing an MRI scan, as it would be dangerous to use metal wiring in the scanner's magnetic field.

Pneumatic intercoms can be applied to motorcycle helmets for pilot-passenger communication. Similar systems are common on ultralight aviation too. They are sometimes preferred over Bluetooth or other radio technologies due to their simplicity and absence of batteries.

The principle of the speaking tube can be found on certain playground equipment, which employs tubing connecting sound horns or other speaking boxes to allow voices to travel to separate points, for the amusement of the children.

See also

Related Research Articles

<span class="mw-page-title-main">Telephone</span> Telecommunications device

A telephone, colloquially referred to as a phone, is a telecommunications device that permits two or more users to conduct a conversation when they are too far apart to be easily heard directly. A telephone converts sound, typically and most efficiently the human voice, into electronic signals that are transmitted via cables and other communication channels to another telephone which reproduces the sound to the receiving user. The term is derived from Ancient Greek: τῆλε, romanized: tēle, lit. 'far' and φωνή, together meaning distant voice.

<span class="mw-page-title-main">Loudspeaker</span> Converts an electrical audio signal into a corresponding sound

A loudspeaker is an electroacoustic transducer that converts an electrical audio signal into a corresponding sound. A speaker system, also often simply referred to as a speaker or loudspeaker, comprises one or more such speaker drivers, an enclosure, and electrical connections possibly including a crossover network. The speaker driver can be viewed as a linear motor attached to a diaphragm which couples that motor's movement to motion of air, that is, sound. An audio signal, typically from a microphone, recording, or radio broadcast, is amplified electronically to a power level capable of driving that motor in order to reproduce the sound corresponding to the original unamplified electronic signal. This is thus the opposite function to the microphone; indeed the dynamic speaker driver, by far the most common type, is a linear motor in the same basic configuration as the dynamic microphone which uses such a motor in reverse, as a generator.

<span class="mw-page-title-main">Pitch pipe</span>

A pitch pipe is a small device used to provide a pitch reference for musicians. Although it may be described as a musical instrument, it is not typically used to play music as such.

An audiophile is a person who is enthusiastic about high-fidelity sound reproduction. An audiophile seeks to reproduce recorded music to achieve high sound quality, typically in a quiet listening space and in a room with good acoustics.

<span class="mw-page-title-main">Headphones</span> Device placed near the ears that plays sound

Headphones are a pair of small loudspeaker drivers worn on or around the head over a user's ears. They are electroacoustic transducers, which convert an electrical signal to a corresponding sound. Headphones let a single user listen to an audio source privately, in contrast to a loudspeaker, which emits sound into the open air for anyone nearby to hear. Headphones are also known as earphones or, colloquially, cans. Circumaural and supra-aural headphones use a band over the top of the head to hold the drivers in place. Another type, known as earbuds or earpieces, consists of individual units that plug into the user's ear canal. A third type are bone conduction headphones, which typically wrap around the back of the head and rest in front of the ear canal, leaving the ear canal open. In the context of telecommunication, a headset is a combination of a headphone and microphone.

<span class="mw-page-title-main">Megaphone</span> Portable or hand-held device to amplify voices and sounds

A megaphone, speaking trumpet, bullhorn, blowhorn, or loudhailer is usually a portable or hand-held, cone-shaped acoustic horn used to amplify a person's voice or other sounds and direct it in a given direction. The sound is introduced into the narrow end of the megaphone, by holding it up to the face and speaking into it, and the sound waves radiate out the wide end. A megaphone increases the volume of sound by increasing the acoustic impedance seen by the vocal cords, matching the impedance of the vocal cords to the air, so that more sound power is radiated. It also serves to direct the sound waves in the direction the horn is pointing. It somewhat distorts the sound of the voice because the frequency response of the megaphone is greater at higher sound frequencies.

<span class="mw-page-title-main">Phone connector (audio)</span> Family of connectors typically used for analog signals

A phone connector is a family of cylindrically-shaped electrical connectors primarily for analog audio signals. Invented in the late 19th century for telephone switchboards, the phone connector remains in use for interfacing wired audio equipment, such as headphones, speakers, microphones, mixing consoles, and electronic musical instruments. A male connector, is mated into a female connector, though other terminology is used.

<span class="mw-page-title-main">Public address system</span> Electronic system for amplifying sound

A public address system is an electronic system comprising microphones, amplifiers, loudspeakers, and related equipment. It increases the apparent volume (loudness) of a human voice, musical instrument, or other acoustic sound source or recorded sound or music. PA systems are used in any public venue that requires that an announcer, performer, etc. be sufficiently audible at a distance or over a large area. Typical applications include sports stadiums, public transportation vehicles and facilities, and live or recorded music venues and events. A PA system may include multiple microphones or other sound sources, a mixing console to combine and modify multiple sources, and multiple amplifiers and loudspeakers for louder volume or wider distribution.

<span class="mw-page-title-main">Siren (alarm)</span> Noise-making device

A siren is a loud noise-making device. Civil defense sirens are mounted in fixed locations and used to warn of natural disasters or attacks. Sirens are used on emergency service vehicles such as ambulances, police cars, and fire engines. There are two general types: mechanical and electronic.

<span class="mw-page-title-main">Intercom</span> Voice communications system for use within a local area

An intercom, also called an intercommunication device, intercommunicator, or interphone, is a stand-alone voice communications system for use within a building, small collection of buildings or portably within a small coverage area, which functions independently of the public telephone network. Intercoms are generally mounted permanently in buildings and vehicles, but can also be detachable and portable. Intercoms can incorporate connections to public address loudspeaker systems, walkie talkies, telephones, and other intercom systems. Some intercom systems incorporate control of devices such as signal lights and door latches.

<span class="mw-page-title-main">Steam whistle</span> Audible warning device powered by steam

A steam whistle is a device used to produce sound in the form of a whistle using live steam, which creates, projects, and amplifies its sound by acting as a vibrating system.

<span class="mw-page-title-main">Beyerdynamic</span> German audio equipment manufacturer

Beyerdynamic GmbH & Co. KG is a German manufacturer of microphones, headphones, wireless audio systems, and conference systems. Headquartered in Heilbronn, Germany, Beyerdynamic has been family-owned since its founding in 1924.

<span class="mw-page-title-main">Carbon microphone</span> Microphone design

The carbon microphone, also known as carbon button microphone, button microphone, or carbon transmitter, is a type of microphone, a transducer that converts sound to an electrical audio signal. It consists of two metal plates separated by granules of carbon. One plate is very thin and faces toward the speaking person, acting as a diaphragm. Sound waves striking the diaphragm cause it to vibrate, exerting a varying pressure on the granules, which in turn changes the electrical resistance between the plates. Higher pressure lowers the resistance as the granules are pushed closer together. A steady direct current is passed between the plates through the granules. The varying resistance results in a modulation of the current, creating a varying electric current that reproduces the varying pressure of the sound wave. In telephony, this undulating current is directly passed through the telephone wires to the central office. In public address systems it is amplified by an audio amplifier. The frequency response of most carbon microphones, however, is limited to a narrow range, and the device produces significant electrical noise.

<span class="mw-page-title-main">AKG (company)</span> Acoustics engineering and manufacturing company

AKG Acoustics is an acoustics engineering and manufacturing company. It was founded in 1947 by Rudolf Görike and Ernest Plass in Vienna, Austria. It is a part of Harman International Industries, a subsidiary of Samsung Electronics since 2017.

<span class="mw-page-title-main">Moving iron speaker</span>

The moving iron speaker was the earliest type of electric loudspeaker. They are still used today in some miniature speakers where small size and low cost are more important than sound quality. A moving iron speaker consists of a ferrous-metal diaphragm or reed, a permanent magnet and a coil of insulated wire. The coil is wound around the permanent magnet to form a solenoid. When an audio signal is applied to the coil, the strength of the magnetic field varies, and the springy diaphragm or reed moves in response to the varying force on it. The moving iron loudspeaker Bell telephone receiver was of this form. Large units had a paper cone attached to a ferrous metal reed.

<span class="mw-page-title-main">Audio headset</span> Telephone or computer accessory

A headset is a combination of headphone and microphone. Headsets connect over a telephone or to a computer, allowing the user to speak and listen while keeping both hands free. They are commonly used in customer service and technical support centers, where employees can converse with customers while typing information into a computer. They are also common among computer gamers and let them talk with each other and hear others while using their keyboards and mice to play the game.

<span class="mw-page-title-main">Gudastviri</span> Musical instrument

The gudastviri is a droneless, double-chantered, horn-belled bagpipe played in Georgia. The term comes from the words guda (bag) and stviri (whistling). In some regions, the instrument is called the chiboni, stviri, or tulumi.

<span class="mw-page-title-main">Home audio</span> Audio electronics for home entertainment

Home audio refer to audio consumer electronics designed for home entertainment, such as integrated systems like shelf stereos, as well as individual components like loudspeakers and surround sound receivers.

<span class="mw-page-title-main">Wind instrument</span> Class of musical instruments with air resonator

A wind instrument is a musical instrument that contains some type of resonator in which a column of air is set into vibration by the player blowing into a mouthpiece set at or near the end of the resonator. The pitch of the vibration is determined by the length of the tube and by manual modifications of the effective length of the vibrating column of air. In the case of some wind instruments, sound is produced by blowing through a reed; others require buzzing into a metal mouthpiece, while yet others require the player to blow into a hole at an edge, which splits the air column and creates the sound.

<span class="mw-page-title-main">Music technology</span> Use of technology by musicians

Music technology is the study or the use of any device, mechanism, machine or tool by a musician or composer to make or perform music; to compose, notate, playback or record songs or pieces; or to analyze or edit music.

References

  1. 1 2 3 "Voicepipes and Speaking-Tubes". The Museum of Retro-Technology. 15 March 2010. Archived from the original on 10 March 2012. Retrieved 17 October 2012.
  2. Goodwin, Peter (2012). HMS Victory. Haynes. p. 69. ISBN   9780857330857.
  3. http://familytreemaker.genealogy.com/users/w/a/r/Silas-j-Ward/BOOK-0001/0003-0010.html [ user-generated source ]
  4. Vincent Orange, "Barry, Robert Raymond Smith- (1886–1949)", Oxford Dictionary of National Biography, Oxford University Press, 2004 Retrieved 12 September 2007