Cut (earthworks)

Last updated • 3 min readFrom Wikipedia, The Free Encyclopedia
Road cutting Road cut.jpg
Road cutting

In civil engineering, a cut or cutting is where soil or rock from a relative rise is removed.

Contents

Cuts are typically used in road, rail, and canal construction to reduce a route's length and grade. Cut and fill construction uses the spoils from cuts to fill in defiles to create straight routes at steady grades cost-effectively.

Cuts are used as alternatives to indirect routes, embankments, or viaducts. They also have the advantage of comparatively lower noise pollution than elevated or at-grade solutions.

In river management, the term cut or cutting is also used, which refers to the action of short-cutting a meander, in order to speed a waterway's flow.

History

Talerddig cutting through the granite Cambrian Mountains, Wales in 2001. Created as part of the Newtown and Machynlleth Railway, with a depth of 120 feet (37 m), it was the deepest cutting in the world at the time of its opening in the early 1860s. The original nearly-vertical sides have since been trimmed back. Railway Cutting at the summit of Talerddig bank - geograph.org.uk - 195516.jpg
Talerddig cutting through the granite Cambrian Mountains, Wales in 2001. Created as part of the Newtown and Machynlleth Railway, with a depth of 120 feet (37 m), it was the deepest cutting in the world at the time of its opening in the early 1860s. The original nearly-vertical sides have since been trimmed back.

The term cutting appears in the 19th century literature to designate rock cuts developed to moderate grades of railway lines. [1] Railway Age's Comprehensive Railroad Dictionary defines a cut as "a passage cut for the roadway through an obstacle of rock or dirt." [2]

Creation

Open-cut station of the New York City Subway Beverley BMT sta house from platform jeh.jpg
Open-cut station of the New York City Subway

Cuts can be created by multiple passes of a shovel, grader, scraper or excavator, or by blasting. [3] One unusual means of creating a cut is to remove the roof of a tunnel through daylighting. Material removed from cuts is ideally balanced by material needed for fills along the same route, but this is not always the case when cut material is unsuitable for use as fill.

The word is also used in the same sense in mining, in particular Open-pit mining. The use of cuttings often provides byproducts as a form of mineral extraction, commonly sand, clay or gravel; the cost of building drains, reinforcing banks against landslide and a high water table are factors which commonly limit its use in certain areas.

Types of cut

There are at least two types of cut, sidehill cut and through cut. The former permits passage of a transportation route alongside of, or around a hill, where the slope is transverse to the roadway or the railway. A sidehill cut can be formed by means of sidecasting, i.e., cutting on the high side balanced by moving the material to build up the low side to achieve a flat surface for the route. In contrast, through cuts, where the adjacent grade is higher on both sides of the route, require removal of material from the area since it cannot be dumped alongside the route. [4]

A ledge is a cut in the side of a cliff well above the bottom of a gorge.

Lock cut

A lock cut on the River Thames at Bray Lock, Berkshire. The tall wooden poles are designed for boats to tie on to while awaiting entry into the lock. Bray Lock, Buckinghamshire.jpg
A lock cut on the River Thames at Bray Lock, Berkshire. The tall wooden poles are designed for boats to tie on to while awaiting entry into the lock.

A lock cut is a section of a river or other inland waterway immediately upstream and downstream of a lock which has been modified to provide locations for boats to moor while waiting for the lock gates to open or to allow people to board or alight vessels.

Notable cuts

Canal

Rail

Asia

Americas

Australia

Europe

Excavation of Olive Mount cutting, Liverpool. Watercolour by T.T.Bury (1833) The cutting was 20 ft (6.1 m) wide and 70 ft (21.3 m) deep. Construction required the removal of 480,000 cubic yards (370,000 m) of sandstone. Excavation of Olive Mount, from Bury's Liverpool and Manchester Railway, 1831 - artfinder 76057.jpg
Excavation of Olive Mount cutting, Liverpool. Watercolour by T.T.Bury (1833) The cutting was 20 ft (6.1 m) wide and 70 ft (21.3 m) deep. Construction required the removal of 480,000 cubic yards (370,000 m) of sandstone.

Road

See also

Related Research Articles

<span class="mw-page-title-main">Kennet and Avon Canal</span> Canal in southern England

The Kennet and Avon Canal is a waterway in southern England with an overall length of 87 miles (140 km), made up of two lengths of navigable river linked by a canal. The name is used to refer to the entire length of the navigation rather than solely to the central canal section. From Bristol to Bath the waterway follows the natural course of the River Avon before the canal links it to the River Kennet at Newbury, and from there to Reading on the River Thames. In all, the waterway incorporates 105 locks.

<span class="mw-page-title-main">Bridgwater and Taunton Canal</span> Canal in south-west England

The Bridgwater and Taunton Canal is a canal in the south-west of England between Bridgwater and Taunton, opened in 1827 and linking the River Tone to the River Parrett. There were a number of abortive schemes to link the Bristol Channel to the English Channel by waterway in the 18th and early 19th centuries. These schemes followed the approximate route eventually taken by the Bridgwater and Taunton Canal, but the canal was instead built as part of a plan to link Bristol to Taunton by waterway.

<span class="mw-page-title-main">Caledonian Canal</span> Artificial waterway in Scotland

The Caledonian Canal connects the Scottish east coast at Inverness with the west coast at Corpach near Fort William in Scotland. The canal was constructed in the early nineteenth century by Scottish engineer Thomas Telford.

<span class="mw-page-title-main">Llangollen Canal</span> Canal in Wales and Shropshire, UK

The Llangollen Canal is a navigable canal crossing the border between England and Wales. The waterway links Llangollen in Denbighshire, north Wales, with Hurleston in south Cheshire, via the town of Ellesmere, Shropshire. The name, which was coined in the 1980s, is a modern designation for parts of the historic Ellesmere Canal and the Llangollen navigable feeder, both of which became part of the Shropshire Union Canals in 1846.

<span class="mw-page-title-main">Bow Back Rivers</span> Waterways in east London

Bow Back Rivers or Stratford Back Rivers is a complex of waterways between Bow and Stratford in east London, England, which connect the River Lea to the River Thames. Starting in the twelfth century, works were carried out to drain Stratford Marshes and several of the waterways were constructed to power watermills. Bow Creek provided the final outfall to the Thames, and the other channels were called Abbey Creek, Channelsea River, City Mill River, Prescott Channel, Pudding Mill River, Saint Thomas Creek, Three Mills Back River, Three Mills Wall River and Waterworks River.

<span class="mw-page-title-main">Montgomery Canal</span> Canal in Shropshire, England, and Powys, Wales

The Montgomery Canal, known colloquially as "The Monty", is a partially restored canal in eastern Powys and northwest Shropshire. The canal runs 33 miles (53 km) from the Llangollen Canal at Frankton Junction to Newtown via Llanymynech and Welshpool and crosses the England–Wales border.

<span class="mw-page-title-main">Cut and fill</span> Earthmoving technique to minimize labor

In earthmoving, cut and fill is the process of constructing a railway, road or canal whereby the amount of material from cuts roughly matches the amount of fill needed to make nearby embankments to minimize the amount of construction labor.

<span class="mw-page-title-main">Macclesfield Canal</span> Canal in Cheshire, England

The Macclesfield Canal is a canal in east Cheshire, England. There were various proposals for a canal to connect the town of Macclesfield to the national network from 1765 onwards, but it was not until 1824 that a scheme came to fruition. There were already suggestions by that date that a railway would be better, but the committee that had been formed elected for a canal and the engineer Thomas Telford endorsed the decision. The canal as built was a typical Telford canal, constructed using cut and fill, with numerous cuttings and embankments to enable it to follow as straight a course as possible, although Telford had little to do with its construction, which was managed by William Crosley.

<span class="mw-page-title-main">Sankey Viaduct</span> Bridge

The Sankey Viaduct is a railway viaduct in North West England. It is a designated Grade I listed building and has been described as being "the earliest major railway viaduct in the world".

<span class="mw-page-title-main">Dudley Canal</span> Canal in the West Midlands, England

The Dudley Canal is a canal passing through Dudley in the West Midlands of England. The canal is part of the English and Welsh network of connected navigable inland waterways and forms part of the popular Stourport Ring narrowboat cruising route.

<span class="mw-page-title-main">Embankment (earthworks)</span> Wall or bank to carry a road or rail over low ground or waters edge

An embankment is a raised wall, bank or mound made of earth or stones, that are used to hold back water or carry a roadway. A road, railway line, or canal is normally raised onto an embankment made of compacted soil to avoid a change in level required by the terrain, the alternatives being either to have an unacceptable change in level or detour to follow a contour. A cutting is used for the same purpose where the land is originally higher than required.

<span class="mw-page-title-main">Itchen Navigation</span> Disused canal system in Hampshire, England

The Itchen Navigation is a 10.4-mile (16.7 km) disused canal system in Hampshire, England, that provided an important trading route from Winchester to the sea at Southampton for about 150 years. Improvements to the River Itchen were authorised by act of parliament in 1665, but progress was slow, and the navigation was not declared complete until 1710. It was known as a navigation because it was essentially an improved river, with the main river channel being used for some sections, and cuts with locks used to bypass the difficult sections. Its waters are fed from the River Itchen. It provided an important method of moving goods, particularly agricultural produce and coal, between the two cities and the intervening villages.

<span class="mw-page-title-main">Bosley Lock Flight</span>

Bosley Lock Flight is a flight of twelve canal locks, situated on the Macclesfield Canal at Bosley, near Macclesfield, Cheshire, England. The locks are substantially built with stone blocks, and unusually for narrow locks have mitre gates at both ends. They were each built with a side pond, which enabled some of the water to be re-used during a filling and emptying cycle. The side ponds have been disused for many years, but there are plans to reinstate one of them for demonstration purposes.

<span class="mw-page-title-main">Petworth Canal</span> Canal in West Sussex, England

The Petworth Canal was one of Britain's shorter lasting canals, opened in 1795 and dismantled in 1826. Upon completion of the Rother Navigation, the Earl of Egremont used his estate workforce to build the 1¼ mile long canal from just upstream of the Shopham Cut to Haslingbourne, with two locks, each with a rise of 8 feet and 6 inches. The Haslingbourne Stream was diverted to provide the water supply, and still flows in the canal bed from Haslingbourne to the site of Haines Lock. The initial intention was to extend the canal through the Shimmings Valley to Hamper's Green on the north side of Petworth, then northwards to join the Wey Navigation at Shalford.

<span class="mw-page-title-main">Spon Lane Junction</span>

Spon Lane Junction is the original junction of the Wednesbury Canal and the Birmingham Canal, near Oldbury in the West Midlands, England.

<span class="mw-page-title-main">Bromford Junction</span>

Bromford Junction is a canal junction at the foot of the Spon Lane Locks where the Spon Lane Locks Branch meets the BCN New Main Line near Oldbury in the West Midlands, England.

<span class="mw-page-title-main">Slough Arm</span> Arm of the Grand Union Canal in the United Kingdom

The Slough Arm is a short canal branch from the Grand Union Main Line to Slough in Berkshire, England. It was originally opened to serve the brick-making industry. The last commercial traffic was carried in 1960, but as the plans to fill it in were opposed locally, the stretch was re-opened in 1975 and has remained in use since.

<span class="mw-page-title-main">Three Mills Lock</span> Lock on Prescott Channel

Three Mills Lock, also known as Prescott Lock, is a lock on the Prescott Channel on the River Lea in London. The current structure was constructed by British Waterways and officially opened on 5 June 2009.

<span class="mw-page-title-main">Pequest Fill</span> Embankment in New Jersey, US

The Pequest Fill is a three-mile (4.8 km) railroad embankment in northwestern New Jersey completed in 1911 by the Delaware, Lackawanna and Western Railroad. Part of the Lackawanna Cut-Off, it was touted as the largest fill and the highest embankment ever built for a railroad.

<span class="mw-page-title-main">Burnley Embankment</span> Waterway in the United Kingdom

The Burnley Embankment is an embankment carrying the Leeds and Liverpool Canal across the Calder and Brun valleys in Burnley, Lancashire. Also known as the Straight Mile, the embankment is 1,256 yards long and the canal runs up to 60 feet (18 m) above the valley floor. The structure was chosen as one of the original Seven Wonders of the Waterways, and has been awarded a Red Wheel by the Transport Trust.

References

  1. Alexander Smith (1875) A new history of Aberdeenshire
  2. Robert G. Lewis et al., eds., Railway Age's Comprehensive Railroad Dictionary (Omaha, Neb.: Simmons-Boardman Books, 1984), p. 48. That reference does not include a definition for the corresponding term "fill."
  3. Herbert L. Nichols, Jr., and David A. Day, P.E., Moving the Earth: The Workbook of Excavation, 5th ed. (New York: McGraw-Hill, 2005), pp. 8.16 et seq.
  4. Nichols and Day, Moving the Earth, p. 8.16.