Point-to-multipoint communication

Last updated
A point-to-multipoint radio base station manufactured by CableFree installed for a wireless internet service provider in Rotterdam. The station has four radio interfaces each connected to a separate sector antenna, each providing 90 degrees coverage. Within 20 km of this base station, customer-premises equipment with high gain directional antennas are installed on sites which can then connect to the base station to receive broadband data connections of typically 10-200 Mbit/s capacity. CableFree-Point-to-Multipoint-Rotterdam-Europe.jpg
A point-to-multipoint radio base station manufactured by CableFree installed for a wireless internet service provider in Rotterdam. The station has four radio interfaces each connected to a separate sector antenna, each providing 90 degrees coverage. Within 20 km of this base station, customer-premises equipment with high gain directional antennas are installed on sites which can then connect to the base station to receive broadband data connections of typically 10–200 Mbit/s capacity.

In telecommunications, point-to-multipoint communication (P2MP, PTMP or PMP) is communication which is accomplished via a distinct type of one-to-many connection, providing multiple paths from a single location to multiple locations. [1]

Contents

Point-to-multipoint telecommunications is typically used in wireless Internet and IP telephony via gigahertz radio frequencies. P2MP systems have been designed with and without a return channel from the multiple receivers. A central antenna or antenna array broadcasts to several receiving antennas and the system uses a form of time-division multiplexing to allow for the return channel traffic.

In contemporary usage, the term point-to-multipoint wireless communications relates to fixed wireless data communications for Internet or voice over IP via radio or microwave frequencies in the gigahertz range.

Point-to-multipoint is the most popular approach for wireless communications that have a large number of nodes, end destinations or end users. Point to Multipoint generally assumes there is a central base station to which remote subscriber units or customer premises equipment (CPE) (a term that was originally used in the wired telephone industry) are connected over the wireless medium. Connections between the base station and subscriber units can be either line-of-sight or, for lower-frequency radio systems, non-line-of-sight where link budgets permit. [2] Generally, lower frequencies can offer non-line-of-sight connections. Various software planning tools can be used to determine feasibility of potential connections using topographic data as well as link budget simulation. Often the point to multipoint links are installed to reduce the cost of infrastructure and increase the number of CPE's and connectivity. [2]

Point-to-multipoint wireless networks employing directional antennas are affected by the hidden node problem (also called hidden terminal) in case they employ a CSMA/CA medium access control protocol. The negative impact of the hidden node problem can be mitigated using a time-division multiple access (TDMA) based protocol or a polling protocol rather than the CSMA/CA protocol. [3]

The telecommunications signal in a point-to-multipoint system is typically bi-directional, TDMA or channelized. Systems using frequency-division duplexing (FDD) offer full-duplex connections between base station and remote sites, and time-division duplex (TDD) systems offer half-duplex connections.

Point-to-multipoint systems can be implemented in licensed, semi-licensed or unlicensed frequency bands depending on the specific application. point-to-point and point-to-multipoint links are very popular in the wireless industry and when paired with other high-capacity wireless links or technologies such as free space optics (FSO) can be referred to as backhaul.

The base station may have a single omnidirectional antenna or multiple sector antennas, the latter of which allowing greater range and capacity.

See also

Related Research Articles

Wireless broadband

Wireless broadband is telecommunications technology that provides high-speed wireless Internet access or computer networking access over a wide area. The term comprises both fixed and mobile broadband.

Time-division multiple access

Time-division multiple access (TDMA) is a channel access method for shared-medium networks. It allows several users to share the same frequency channel by dividing the signal into different time slots. The users transmit in rapid succession, one after the other, each using its own time slot. This allows multiple stations to share the same transmission medium while using only a part of its channel capacity. Dynamic TDMA is a TDMA variant that dynamically reserves a variable number of time slots in each frame to variable bit-rate data streams, based on the traffic demand of each data stream.

Wireless network Any network at least partly not connected by physical cables of any kind

A wireless network is a computer network that uses wireless data connections between network nodes.

Carrier-sense multiple access with collision avoidance Computer network multiple access method

Carrier-sense multiple access with collision avoidance (CSMA/CA) in computer networking, is a network multiple access method in which carrier sensing is used, but nodes attempt to avoid collisions by beginning transmission only after the channel is sensed to be "idle". When they do transmit, nodes transmit their packet data in its entirety.

Repeater

In telecommunications, a repeater is an electronic device that receives a signal and retransmits it. Repeaters are used to extend transmissions so that the signal can cover longer distances or be received on the other side of an obstruction. Some types of repeaters broadcast an identical signal, but alter its method of transmission, for example, on another frequency or baud rate.

In a telecommunications network, a link is a communication channel that connects two or more devices for the purpose of data transmission. The link may be a dedicated physical link or a virtual circuit that uses one or more physical links or shares a physical link with other telecommunications links.

In telecommunications and computer networks, a channel access method or multiple access method allows more than two terminals connected to the same transmission medium to transmit over it and to share its capacity. Examples of shared physical media are wireless networks, bus networks, ring networks and point-to-point links operating in half-duplex mode.

Communication channel

A communication channel refers either to a physical transmission medium such as a wire, or to a logical connection over a multiplexed medium such as a radio channel in telecommunications and computer networking. A channel is used to convey an information signal, for example a digital bit stream, from one or several senders to one or several receivers. A channel has a certain capacity for transmitting information, often measured by its bandwidth in Hz or its data rate in bits per second.

Wireless local loop (WLL), is the use of a wireless communications link as the "last mile / first mile" connection for delivering plain old telephone service (POTS) or Internet access to telecommunications customers. Various types of WLL systems and technologies exist.

In telecommunications, a point-to-point connection refers to a communications connection between two communication endpoints or nodes. An example is a telephone call, in which one telephone is connected with one other, and what is said by one caller can only be heard by the other. This is contrasted with a point-to-multipoint or broadcast connection, in which many nodes can receive information transmitted by one node. Other examples of point-to-point communications links are leased lines and microwave radio relay.

Hidden node problem Problem in wireless networking

In wireless networking, the hidden node problem or hidden terminal problem occurs when a node can communicate with a wireless access point (AP), but cannot directly communicate with other nodes that are communicating with that AP. This leads to difficulties in medium access control sublayer since multiple nodes can send data packets to the AP simultaneously, which creates interference at the AP resulting in no packet getting through.

Local Multipoint Distribution Service (LMDS) is a broadband wireless access technology originally designed for digital television transmission (DTV). It was conceived as a fixed wireless, point-to-multipoint technology for utilization in the last mile. LMDS commonly operates on microwave frequencies across the 26 GHz and 29 GHz bands. In the United States, frequencies from 31.0 through 31.3 GHz are also considered LMDS frequencies.

Cellular network Communication network

A cellular network or mobile network is a communication network where the link to and from end nodes is wireless. The network is distributed over land areas called "cells", each served by at least one fixed-location transceiver. These base stations provide the cell with the network coverage which can be used for transmission of voice, data, and other types of content. A cell typically uses a different set of frequencies from neighboring cells, to avoid interference and provide guaranteed service quality within each cell.

The air interface, or access mode, is the communication link between the two stations in mobile or wireless communication. The air interface involves both the physical and data link layers of the OSI model for a connection.

A duplex communication system is a point-to-point system composed of two or more connected parties or devices that can communicate with one another in both directions. Duplex systems are employed in many communications networks, either to allow for simultaneous communication in both directions between two connected parties or to provide a reverse path for the monitoring and remote adjustment of equipment in the field. There are two types of duplex communication systems: full-duplex (FDX) and half-duplex (HDX).

In a hierarchical telecommunications network, the backhaul portion of the network comprises the intermediate links between the core network, or backbone network, and the small subnetworks at the edge of the network.

Cambium Networks is a wireless infrastructure provider that offers fixed wireless and Wi-Fi to broadband service providers and enterprises to provide Internet access. An American telecommunications infrastructure company, it provides wireless technology, including Enterprise WiFi, switching solutions, Internet of Things, and fixed wireless broadband and Wi-Fi for enterprises. Publicly traded on the NASDAQ stock exchange, it spun out of Motorola in October 2011.

Long-range Wi-Fi is used for low-cost, unregulated point-to-point computer network connections, as an alternative to other fixed wireless, cellular networks or satellite Internet access.

Multi-user MIMO (MU-MIMO) is a set of multiple-input and multiple-output (MIMO) technologies for multipath wireless communication, in which multiple users or terminals, each radioing over one or more antennas, communicate with one another. In contrast, single-user MIMO (SU-MIMO) involves a single multi-antenna-equipped user or terminal communicating with precisely one other similarly equipped node. Analogous to how OFDMA adds multiple-access capability to OFDM in the cellular-communications realm, MU-MIMO adds multiple-user capability to MIMO in the wireless realm.

Mobile Slotted Aloha

Mobile Slotted Aloha (MS-Aloha) is a wireless network protocol proposed for applications such as vehicle networks.

References

  1. M. Cover, Thomas; Joy A. Thomas (1991). Elements of Information Theory . Wiley-Interscience. ISBN   0-471-06259-6.
  2. 1 2 Anderson, Harry. R (2003). Fixed Broadband Wireless System Design. Chichester: Wiley. ISBN   0-470-84438-8.
  3. "Point to Multipoint Wireless". fluidmesh.com. Retrieved 2015-08-12.