Two designs were considered, operated as either a pure fusion or hybrid fusion-fission system. In the former, the energy generated by the fusion reactions is used directly. In the later, the neutrons given off by the fusion reactions are used to cause fission reactions in a surrounding blanket of uranium or other nuclear fuel, and those fission events are responsible for most of the energy release. In both cases, conventional steam turbine systems are used to extract the heat and produce electricity.
Construction on NIF completed in 2009 and it began a lengthy series of run-up tests to bring it to full power. Through 2011 and into 2012, NIF ran the "national ignition campaign" to reach the point at which the fusion reaction becomes self-sustaining, a key goal that is a basic requirement of any practical IFE system. NIF failed in this goal, with fusion performance that was well below ignition levels and differing considerably from predictions. With the problem of ignition unsolved, the LIFE project was canceled in 2013.
The LIFE program was criticized through its development for being based on physics that had not yet been demonstrated. In one pointed assessment, Robert McCrory, director of the Laboratory for Laser Energetics, stated: "In my opinion, the overpromising and overselling of LIFE did a disservice to Lawrence Livermore Laboratory."[1]
Background
Lawrence Livermore National Laboratory (LLNL) has been a leader in laser-driven inertial confinement fusion (ICF) since the initial concept was developed by LLNL employee John Nuckols in the late 1950s.[2][3] The basic idea was to use a driver to compress a small pellet known as the target that contains the fusion fuel, a mix of deuterium (D) and tritium (T). If the compression reaches high enough values, fusion reactions begin to take place, releasing alpha particles and neutrons. The alphas may impact atoms in the surrounding fuel, heating them to the point where they undergo fusion as well. If the rate of alpha heating is higher than heat losses to the environment, the result is a self-sustaining chain reaction known as ignition.[4][5]
Comparing the driver energy input to the fusion energy output produces a number known as fusion energy gain factor, labelled Q. A Q value of at least 1 is required for the system to produce net energy. Since some energy is needed to run the reactor, in order for there to be net electrical output, Q has to be at least 3.[6] For commercial operation, Q values much higher than this are needed.[7] For ICF, Qs on the order of 25 to 50 are needed to recoup both the electrical generation losses and the large amount of power used to power the driver. In the fall of 1960, theoretical work carried out at LLNL suggested that gains of the required order would be possible with drivers on the order of 1MJ.[8]
At the time, a number of different drivers were considered, but the introduction of the laser later that year provided the first obvious solution with the right combination of features. The desired energies were well beyond the state of the art in laser design, so LLNL began a development program in the mid-1960s to reach these levels.[9] Each increase in energy led to new and unexpected optical phenomena that had to be overcome, but these were largely solved by the mid-1970s. Working in parallel with the laser teams, physicists studying the expected reaction using computer simulations adapted from thermonuclear bomb work developed a program known as LASNEX that suggested Q of 1 could be produced at much lower energy levels, in the kilojoule range, levels that the laser team were now able to deliver.[10][11]
From the late-1970s, LLNL developed a series of machines to reach the conditions being predicted by LASNEX and other simulations. With each iteration, the experimental results demonstrated that the simulations were incorrect. The first machine, the Shiva laser of the late 1970s, produced compression on the order of 50 to 100 times, but did not produce fusion reactions anywhere near the expected levels. The problem was traced to the issue of the infrared laser light heating electrons and mixing them in the fuel, and it was suggested that using ultraviolet light would solve the problem. This was addressed on the Nova laser of the 1980s, which was designed with the specific intent of producing ignition. Nova did produce large quantities of fusion, with shots producing as much as 107 neutrons, but failed to reach ignition. This was traced to the growth of Rayleigh–Taylor instabilities, which greatly increased the required driver power.[12]
Ultimately all of these problems were considered to be well understood, and a much larger design emerged, NIF. NIF was designed to provide about twice the required driver energy, allowing some margin of error. NIF's design was finalized in 1994, with construction to be completed by 2002. Construction began in 1997 but took over a decade to complete, with major construction being declared complete in 2009.[13]
LIFE
Throughout the development of the ICF concept at LLNL and elsewhere, several small efforts had been made to consider the design of a commercial power plant based on the ICF concept. Examples include SOLASE-H[14] and HYLIFE-II.[15] As NIF was reaching completion in 2008, with the various concerns considered solved, LLNL began a more serious IFE development effort, LIFE.[16]
Conventional fission power plants rely on the chain reaction caused when fission events release thermal neutrons that cause further fission events. Each fission event in U-235 releases two or three neutrons with about 2MeV of kinetic energy. By careful arrangement and the use of various absorber materials, designers can balance the system so one of those neutrons causes another fission event while the other one or two are lost. This balance is known as criticality. Natural uranium is a mix of three isotopes; mainly U-238, with some U-235, and trace amounts of U-234. The neutrons released in the fission of either of the main isotopes will cause fission in U-235, but not in U-238, which requires higher energies around 5MeV. There is not enough U-235 in natural uranium to reach criticality. Commercial light-water nuclear reactors, the most prevalent power reactors in the world, use nuclear fuel containing uranium enriched to 3 to 5% U-235 while the leftover is U-238.[22][23]
Each fusion event in the D-T fusion reactor gives off an alpha particle and a fast neutron with around 14MeV of kinetic energy. This is enough energy to cause fission in U-238, and many other transuranic elements as well. This reaction is used in H-bombs to increase the yield of the fusion section by wrapping it in a layer of depleted uranium, which undergoes rapid fission when hit by the neutrons from the fusion bomb inside. The same basic concept can also be used with a fusion reactor like LIFE, using its neutrons to cause fission in a blanket of fission fuel. Unlike a fission reactor, which burns out its fuel once the U-235 drops below a certain threshold value,[lower-alpha 1] these fission–fusion hybrid reactors can continue producing power from the fission fuel as long as the fusion reactor continues to provide neutrons. As the neutrons have high energy, they can potentially cause multiple fission events, leading to the reactor as a whole producing more energy, a concept known as energy multiplication.[25] Even leftover nuclear fuel taken from conventional nuclear reactors will burn in this fashion. This is potentially attractive because this burns off many of the long lived radioisotopes in the process, producing waste that is only mildly radioactive and lacking most long-lived components.[17]
In most fusion energy designs, fusion neutrons react with a blanket of lithium to breed new tritium for fuel. A major issue with the fission–fusion design is that the neutrons causing fission are no longer available for tritium breeding. While the fission reactions release additional neutrons, these do not have enough energy to complete the breeding reaction with Li-7, which makes up more than 92% of natural lithium. These lower energy neutrons will cause breeding in Li-6, which could be concentrated from the natural lithium ore. However, the Li-6 reaction only produces one tritium per neutron captured, and more than one T per neutron is needed to make up for natural decay and other losses.[26] Using Li-6, neutrons from the fission would make up for the losses, but only at the cost of removing them from causing other fission reactions, lowering the reactor power output. The designer has to choose which is more important; burning up the fuel through fusion neutrons, or providing power through self-induced fission events.[27]
The economics of fission–fusion designs have always been questionable. The same basic effect can be created by replacing the central fusion reactor with a specially designed fission reactor, and using the surplus neutrons from the fission to breed fuel in the blanket. These fast breeder reactors have proven uneconomical in practice, and the greater expense of the fusion systems in the fission–fusion hybrid has always suggested they would be uneconomical unless built in very large units.[28]
Pure IFE
The National Ignition Facility's target chamber's multi-part construction would also be used in LIFE. Several chambers would be used in a production power plant, allowing them to be swapped out for maintenance.
The LIFE concept stopped working along fusion-fission lines around 2009. Following consultations with their partners in the utility industry, the project was redirected toward a pure fusion design with a net electrical output around 1 gigawatt.[29]
Inertial confinement fusionis one of two major lines of fusion power development, the other being magnetic confinement fusion (MCF), notably the tokamak concept which is being built in a major experimental system known as ITER. Magnetic confinement is widely considered to be the superior approach, and has seen significantly greater development activity over the decades. However, there are serious concerns that the MCF approach of ITER cannot ever become economically practical.[30]
One of the cost concerns for MCF designs like ITER is that the reactor materials are subject to the intense neutron flux created by the fusion reactions. When high-energy neutrons impact materials they displace the atoms in the structure leading to a problem known as neutron embrittlement that degrades the structural integrity of the material. This is a problem for fission reactors as well, but the neutron flux and energy in a tokamak is greater than most fission designs. In most MFE designs, the reactor is constructed in layers, with a toroidal inner vacuum chamber, or "first wall", then the lithium blanket, and finally the superconducting magnets that produce the field that confines the plasma. Neutrons stopping in the blanket are desirable, but those that stop in the first wall or magnets degrade them. Disassembling a toroidal stack of elements would be a time-consuming process that would lead to poor capacity factor, which has a significant impact on the economics of the system. Reducing this effect requires the use of exotic materials which have not yet been developed.[31]
As a natural side-effect of the size of the fuel elements and their resulting explosions, ICF designs use a very large reaction chamber many meters across. This lowers the neutron flux on any particular part of the chamber wall through the inverse-square law. Additionally, there are no magnets or other complex systems near or inside the reactor, and the laser is isolated on the far side of long optical paths. The far side of the chamber is empty, allowing the blanket to be placed there and easily maintained. Although the reaction chamber walls and final optics would eventually embrittle and require replacement, the chamber is essentially a large steel ball of relatively simple multi-piece construction that could be replaced without too much effort. The reaction chamber is, on the whole, dramatically simpler than those in magnetic fusion concepts, and the LIFE designs proposed building several and quickly moving them in and out of production.[32]
IFE limitations
NIF's huge flashlamps are both inefficient and impractical. LIFE explored solutions to replace these lamps with smaller and much more efficient LED-pumped lasers.
NIF's laser uses a system of large flashtubes (like those in a photography flashlamp) to optically pump a large number of glass plates. Once the plates are flashed and have settled into a population inversion, a small signal from a separate laser is fed into the optical lines, stimulating the emission in the plates. The plates then dump their stored energy into the growing beam, amplifying it billions of times.[33]
The process is extremely inefficient in energy terms; NIF feeds the flashtubes over 400MJ of energy which produces 1.8MJ of ultraviolet (UV) light. Due to limitations of the target chamber, NIF is only able to handle fusion outputs up to about 50MJ, although shots would generally be about half of that. Accounting for losses in generation, perhaps 20MJ of electrical energy might be extracted at the maximum, accounting for less than 1⁄20 of the input energy.[33]
Another problem with the NIF lasers is that the flashtubes create a significant amount of heat, which warms the laser glass enough to cause it to deform. This requires a lengthy cooling-off period between shots, on the order of 12 hours. In practice, NIF manages a shot rate of less than one shot per day.[34] To be useful as a power plant, about a dozen shots would have to take place every second, well beyond the capabilities of the NIF lasers.
When originally conceived by Nuckols, laser-driven inertial fusion confinement was expected to require lasers of a few hundred kilojoules and use fuel droplets created by a perfume mister arrangement.[35] LLNLs research since that time has demonstrated that such an arrangement cannot work, and requires machined assemblies for each shot. To be economically useful, an IFE machine would need to use fuel assemblies that cost pennies. Although LLNL does not release prices for their own targets, the similar system at the Laboratory for Laser Energetics at the University of Rochester makes targets for about $1 million each.[36] It is suggested that NIF's targets cost more than $10,000.[37][38]
Mercury
LLNL had begun exploring different solutions to the laser problem while the system was first being described. In 1996 they built a small testbed system known as the Mercury laser that replaced the flashtubes with laser diodes.[39]
One advantage of this design was that the diodes created light around the same frequency as the laser glass' output,[40] as compared to the white light flashtubes where most of the energy in the flash was wasted as it was not near the active frequency of the laser glass.[41] This change increased the energy efficiency to about 10%, a dramatic improvement.[39]
For any given amount of light energy created, the diode lasers give off about 1⁄3 as much heat as a flashtube. Less heat, combined with active cooling in the form of helium blown between the diodes and the laser glass layers, eliminated the warming of the glass and allows Mercury to run continually.[40] In 2008, Mercury was able to fire 10 times a second at 50 joules per shot for hours at a time.[39]
Several other projects running in parallel with Mercury explored various cooling methods and concepts allowing many laser diodes to be packed into a very small space. These eventually produced a system with 100kW of laser energy from a box about 50 centimetres (20in) long, known as a diode array. In a LIFE design, these arrays would replace the less dense diode packaging of the Mercury design.[39]
Beam-in-a-box
LIFE was essentially a combination of the Mercury concepts and new physical arrangements to greatly reduce the volume of the NIF while making it much easier to build and maintain. Whereas an NIF beamline for one of its 192 lasers is over 100 metres (330ft) long, LIFE was based on a design about 10.5 metres (34ft) long that contained everything from the power supplies to frequency conversion optics. Each module was completely independent, unlike NIF which is fed from a central signal from the Master Oscillator, allowing the units to be individually removed and replaced while the system as a whole continued operation.[42]
Each driver cell in the LIFE baseline design contained two of the high-density diode arrays arranged on either side of a large slab of laser glass. The arrays were provided cooling via hook-up pipes at either end of the module. The initial laser pulse was provided by a preamplifier module similar to the one from the NIF, the output of which was switched into the main beamline via a mirror and Pockels celloptical switch. To maximize the energy deposited into the beam from the laser glass, optical switches were used to send the beam to mirrors to reflect the light through the glass four times, in a fashion similar to NIF.[40] Finally, focussing and optical cleanup was provided by optics on either side of the glass, before the beam exited the system through a frequency converter at one end.[42]
The small size and independence of the laser modules allowed the huge NIF building to be dispensed with. Instead, the modules were arranged in groups surrounding the target chamber in a compact arrangement. In baseline designs, the modules were stacked in 2-wide by 8-high groups in two rings above and below the target chamber, shining their light through small holes drilled into the chamber to protect them from the neutron flux coming back out.[43]
The ultimate goal was to produce a system that could be shipped in a conventional semi-trailer truck to the power plant, providing laser energy with 18% end-to-end efficiency, 15 times that of the NIF system. This reduces the required fusion gains into the 25 to 50 area, within the predicted values for NIF. The consensus was that this "beam-in-a-box" system could be built for 3 cents per Watt of laser output, and that would reduce to 0.7 cents/W in sustained production. This would mean that a complete LIFE plant would require about $600million worth of diodes alone, significant, but within the realm of economic possibility.[42]
Inexpensive targets
NIF's targets (centered, in the holder) are expensive machined assemblies that cost thousands of dollars each. LIFE worked with industry partners to reduce this to under a dollar.
Targets for NIF are extremely expensive. Each one consists of a small open-ended metal cylinder with transparent double-pane windows sealing each end. In order to efficiently convert the driver laser's light to the x-rays that drive the compression, the cylinder has to be coated in gold or other heavy metals. Inside, suspended on fine plastic wires, is a hollow plastic sphere containing the fuel. In order to provide symmetrical implosion, the metal cylinder and plastic sphere have extremely high machining tolerances. The fuel, normally a gas at room temperature, is deposited inside the sphere and then cryogenically frozen until it sticks to the inside of the sphere. It is then smoothed by slowly warming it with an infrared laser to form a 100μm smooth layer on the inside of the pellet. Each target costs tens of thousands of dollars.[37]
To address this concern, a considerable amount of LIFE's effort was put into the development of simplified target designs and automated construction that would lower their cost. Working with General Atomics, the LIFE team developed a concept using on-site fuel factories that would mass-produce pellets at a rate of about a million a day. It was expected that this would reduce their price to about 25 cents per target,[44] although other references suggest the target price was closer to 50 cents, and LLNL's own estimates range from 20 to 30 cents.[45]
One less obvious advantage to the LIFE concept is that the amount of tritium required to start the system up is greatly reduced over MFE concepts. In MFE, a relatively large amount of fuel is prepared and put into the reactor, requiring much of the world's entire civilian tritium supply just for startup. LIFE, by virtue of the tiny amount of fuel in any one pellet, can begin operations with much less tritium, on the order of 1⁄10.[32]
Overall design
LIFE.1/MEP's fusion system. The lasers are the grey boxes arranged in groups at the top and bottom of the containment building (the lower ones are just visible). Their light, in blue, is bounced through the optical paths into the target chamber in the center. The machinery on the left circulates the liquid lithium or FLiBe, which removes heat from the chamber to cool it, provides heat to the generators, and extracts tritium for fuel.
The early fusion-fission designs were not well developed and only schematic outlines of the concept were shown. These systems looked like a scaled down version of NIF, with beamlines about 100 metres (330ft) long on either side of a target chamber and power generation area. The laser produced 1.4MJ of UV light 13 times a second. The fusion took place in a 2.5 metres (8ft 2in) target chamber that was surrounded by 40 short tons (36,000kg) of unenriched fission fuel, or alternately about 7 short tons (6,400kg) of Pu or highly enriched uranium from weapons. The fusion system was expected to produce Q on the order of 25 to 30, resulting in 350 to 500MW of fusion energy. The fission processes triggered by the fusion would add an additional energy gain of 4 to 10 times, resulting in a total thermal output between 2000 and 5000MWth. Using high efficiency thermal-to-electric conversion systems like Rankine cycle designs in combination with demonstrated supercritical steam generators would allow about half of the thermal output to be turned into electricity.[46][47]
By 2012, the baseline design of the pure fusion concept, known as the Market Entry Plant (MEP),[lower-alpha 2] had stabilized. This was a self-contained design with the entire fusion section packaged into a cylindrical concrete building not unlike a fission reactor confinement building, although larger at 100 metres (330ft) diameter.[49] The central building was flanked by smaller rectangular buildings on either side, one containing the turbines and power handling systems, the other the tritium plant. A third building, either attached to the plant or behind it depending on the diagram, was used for maintenance.[50]
Inside the central fusion building, the beam-in-a-box lasers were arranged in two rings, one above and one below the target chamber. A total of 384 lasers would provide 2.2MJ of UV light at a 0.351-micrometer wavelength,[40] producing a Q of 21. A light-gas gun was used to fire 15 targets a second into the target chamber.[51] With each shot, the temperature of the target chamber's inner wall is raised from 600°C (1,112°F) to 800°C (1,470°F).[52]
The target chamber is a two-wall structure filled with liquid lithium or a lithium alloy between the walls.[53] The lithium captures neutrons from the reactions to breed tritium, and also acts as the primary coolant loop.[54] The chamber is filled with xenon gas that would slow the ions from the reaction as well as protect the inner wall, or first wall, from the massive x-ray flux.[50] Because the chamber is not highly pressurized, like a fission core, it does not have to be built as a single sphere. Instead, the LIFE chamber is built from eight identical sections that include built-in connections to the cooling loop. They are shipped to the plant and bolted together on two supports, and then surrounded by a tube-based space frame.[55]
To deal with embrittlement, the entire target chamber was designed to be easily rolled out of the center of the building on rails to the maintenance building where it could be rebuilt. The chamber was expected to last four years, and be replaced in one month. The optical system is decoupled from the chamber, which isolates it from vibrations during operation and means that the beamlines themselves do not have to be realigned after chamber replacement.[50]
The plant had a peak generation capability, or nameplate capacity, of about 400MWe, with design features to allow expansion to as much as 1000MWe.[56]
Economics
LIFE plant parameters (MEP: prototype; LIFE.2: first generation commercial plant)[47]
The levelized cost of electricity (LCoE) can be calculated by dividing the total cost to build and operate a power-generating system over its lifetime by the total amount of electricity shipped to the grid during that period. The amount of money is essentially a combination of the capital expense (CAPEX) of the plant and the interest payments on that CAPEX, and the discounted cost of the fuel, the maintenance needed to keep it running and its dismantling, the discounted operational expenses, or OPEX. The amount of power is normally calculated by considering the peak power the plant could produce, and then adjusting that by the capacity factor (CF) to account for downtime due to maintenance or deliberate throttling. As a quick calculation, one can ignore inflation, opportunity costs and minor operational expenses to develop a figure of merit for the cost of electricity.[57]
MEP was not intended to be a production design, and would be able to export only small amounts of electricity. It would, however, serve as the basis for the first production model, LIFE.2. LIFE.2 would produce 2.2GW of fusion energy and convert that to 1GW of electrical at 48% efficiency.[51] Over a year, LIFE would produce 365 days x 24 hours x 0.9 capacity factor x 1,000,000kW nameplate rating = 8billion kWh. In order to generate that power, the system will have to burn 365 x 24 x 60 minutes x 60 seconds x 15 pellets per second x 0.9 capacity = 425million fuel pellets. If the pellets cost the suggested price of 50 cents each, that is over $200million a year to fuel the plant. The average rate for wholesale electricity in the US as of 2015[update] is around 5 cents/kWh,[58] so this power has a commercial value of about $212million, suggesting that LIFE.2 would just barely cover, on average, its own fuel costs.[lower-alpha 4]
CAPEX for the plant is estimated to $6.4billion, so financing the plant over a 20-year period adds another $5billion assuming the 6.5% unsecured rate. Considering CAPEX and fuel alone, the total cost of the plant is 6.4 + 5 + 4 = $15.4billion. Dividing the total cost by the energy produced over the same period gives a rough estimate of the cost of electricity for a 20-year lifetime operation: $15.4billion / 160billionkWh = 9.6cents/kWh. A 40-year operation lifetime would lead to a cost of electricity of 4.8cents/kWh. LLNL calculated the LCOE of LIFE.2 at 9.1 cents using the discounted cash flow methodology described in the 2009 MIT report "the Future of Nuclear Energy".[51][60] Using either value, LIFE.2 would be unable to compete with modern renewable energy sources, which are well below 5 cents/kWh as of 2018[update].[61]
LLNL projected that further development after widespread commercial deployment might lead to further technology improvements and cost reductions, and proposed a LIFE.3 design of about $6.3billion CAPEX and 1.6GW nameplate for a price per watt of $4.2/W. This leads to a projected LCOE of 5.5 cents/kWh,[51] which is competitive with offshore wind as of 2018[update],[62] but unlikely to be so in 2040 when LIFE.3 designs would start construction.[lower-alpha 5] LIFE plants would be wholesale sellers, competing against a baseload rate of about 5.3 cents/kWh as of 2015[update].[58]
The steam turbine section of a power plant, the turbine hall, generally costs about $1/W, and the electrical equipment to feed that power to the grid is about another $1/W.[64] To reach the projected total CAPEX quoted in LIFE documents, this implies that the entire nuclear island has to cost around $4/W for LIFE.2, and just over $2/W for LIFE.3. Modern nuclear plants, benefiting from decades of commercial experience and continuous design work, cost just under $8/W, with approximately half of that in the nuclear island. LLNL's estimates require LIFE.3 to be built in 2040 for about half the cost of a fission plant today.[65]
End of LIFE
NIF construction was completed in 2009 and the lab began a long calibration and setup period to bring the laser to its full capacity. The plant reached its design capacity of 1.8MJ of UV light in 2012.[66] During this period, NIF began running a staged program known as the National Ignition Campaign, with the goal of reaching ignition by 30 September 2012. Ultimately, the campaign failed as unexpected performance problems arose that had not been predicted in the simulations. By the end of 2012 the system was producing best-case shots that were still 1⁄10 of the pressures needed to achieve ignition.[67]
During a progress review after the end of the Campaign, a National Academy of Sciences review board stated that "The appropriate time for the establishment of a national, coordinated, broad-based inertial fusion energy program within DOE is when ignition is achieved."[68] They noted that "the panel assesses that ignition using laser indirect drive is not likely in the next several years."[69]
The LIFE effort was quietly cancelled in early 2013.[70] LLNL's acting director, Bret Knapp, commented on the issue stating that "The focus of our inertial confinement fusion efforts is on understanding ignition on NIF rather than on the LIFE concept. Until more progress is made on ignition, we will direct our efforts on resolving the remaining fundamental scientific challenges to achieving fusion ignition."[1]
Notes
↑ Or, more typically, when the products of previous fission events "poison" the ongoing reaction by capturing neutrons.[24]
↑ RAFMS stands for Reduced Activation Ferritic/Martensitic Steel.
↑ Wholesale prices have dropped since 2015, as of 2018[update], the average cost is closer to 3 cents/kWh, which means LIFE.2 would lose money even at the cheapest possible target prices.[59]
↑ LCoE on wind turbines declined (improved) by 58% between 2009 and 2014, to just over 5.5 cents/kWh.[63]
Related Research Articles
A fusion rocket is a theoretical design for a rocket driven by fusion propulsion that could provide efficient and sustained acceleration in space without the need to carry a large fuel supply. The design requires fusion power technology beyond current capabilities, and much larger and more complex rockets.
Inertial confinement fusion (ICF) is a fusion energy process that initiates nuclear fusion reactions by compressing and heating targets filled with fuel. The targets are small pellets, typically containing deuterium (2H) and tritium (3H).
Fusion power is a proposed form of power generation that would generate electricity by using heat from nuclear fusion reactions. In a fusion process, two lighter atomic nuclei combine to form a heavier nucleus, while releasing energy. Devices designed to harness this energy are known as fusion reactors. Research into fusion reactors began in the 1940s, but as of 2024, no device has reached net power, although net positive reactions have been achieved.
Nuclear weapon designs are physical, chemical, and engineering arrangements that cause the physics package of a nuclear weapon to detonate. There are three existing basic design types:
A neutron source is any device that emits neutrons, irrespective of the mechanism used to produce the neutrons. Neutron sources are used in physics, engineering, medicine, nuclear weapons, petroleum exploration, biology, chemistry, and nuclear power. Neutron source variables include the energy of the neutrons emitted by the source, the rate of neutrons emitted by the source, the size of the source, the cost of owning and maintaining the source, and government regulations related to the source.
This timeline of nuclear fusion is an incomplete chronological summary of significant events in the study and use of nuclear fusion.
The National Ignition Facility (NIF) is a laser-based inertial confinement fusion (ICF) research device, located at Lawrence Livermore National Laboratory in Livermore, California, United States. NIF's mission is to achieve fusion ignition with high energy gain. It achieved the first instance of scientific breakeven controlled fusion in an experiment on December 5, 2022, with an energy gain factor of 1.5. It supports nuclear weapon maintenance and design by studying the behavior of matter under the conditions found within nuclear explosions.
Aneutronic fusion is any form of fusion power in which very little of the energy released is carried by neutrons. While the lowest-threshold nuclear fusion reactions release up to 80% of their energy in the form of neutrons, aneutronic reactions release energy in the form of charged particles, typically protons or alpha particles. Successful aneutronic fusion would greatly reduce problems associated with neutron radiation such as damaging ionizing radiation, neutron activation, reactor maintenance, and requirements for biological shielding, remote handling and safety.
A fusion energy gain factor, usually expressed with the symbol Q, is the ratio of fusion power produced in a nuclear fusion reactor to the power required to maintain the plasma in steady state. The condition of Q = 1, when the power being released by the fusion reactions is equal to the required heating power, is referred to as breakeven, or in some sources, scientific breakeven.
The Shiva laser was a powerful 20-beam infrared neodymium glass laser built at Lawrence Livermore National Laboratory in 1977 for the study of inertial confinement fusion (ICF) and long-scale-length laser-plasma interactions. Presumably, the device was named after the multi-armed form of the Hindu god Shiva, due to the laser's multi-beamed structure. Shiva was instrumental in demonstrating a particular problem in compressing targets with lasers, leading to a major new device being constructed to address these problems, the Nova laser.
Nova was a high-power laser built at the Lawrence Livermore National Laboratory (LLNL) in California, United States, in 1984 which conducted advanced inertial confinement fusion (ICF) experiments until its dismantling in 1999. Nova was the first ICF experiment built with the intention of reaching "ignition", a chain reaction of nuclear fusion that releases a large amount of energy. Although Nova failed in this goal, the data it generated clearly defined the problem as being mostly a result of Rayleigh–Taylor instability, leading to the design of the National Ignition Facility, Nova's successor. Nova also generated considerable amounts of data on high-density matter physics, regardless of the lack of ignition, which is useful both in fusion power and nuclear weapons research.
Inertial Fusion Energy is a proposed approach to building a nuclear fusion power plant based on performing inertial confinement fusion at industrial scale. This approach to fusion power is still in a research phase. ICF first developed shortly after the development of the laser in 1960, but was a classified US research program during its earliest years. In 1972, John Nuckolls wrote a paper predicting that compressing a target could create conditions where fusion reactions are chained together, a process known as fusion ignition or a burning plasma. On August 8, 2021, the NIF at Livermore National Laboratory became the first ICF facility in the world to demonstrate this. This breakthrough drove the US Department of Energy to create an Inertial Fusion Energy program in 2022 with a budget of 3 million dollars in its first year.
The High Power laser Energy Research facility (HiPER), is a proposed experimental laser-driven inertial confinement fusion (ICF) device undergoing preliminary design for possible construction in the European Union. As of 2019, the effort appears to be inactive.
Hybrid nuclear fusion–fission is a proposed means of generating power by use of a combination of nuclear fusion and fission processes.
Fusion ignition is the point at which a nuclear fusion reaction becomes self-sustaining. This occurs when the energy being given off by the reaction heats the fuel mass more rapidly than it cools. In other words, fusion ignition is the point at which the increasing self-heating of the nuclear fusion removes the need for external heating. This is quantified by the Lawson criterion. Ignition can also be defined by the fusion energy gain factor.
KMS Fusion was the first private company to attempt to produce a fusion reactor using the inertial confinement fusion (ICF) approach. The basic concept, developed in 1969 by Keith Brueckner, was to infuse small glass spheres with a fuel gas and then compress the sphere using lasers until they reached the required temperature and pressures. In May 1974 they demonstrated neutron output consistent with small levels of fusion events in a D-T filled target, the first published success for this technique.
John Hopkin Nuckolls is an American physicist who worked his entire career at the Lawrence Livermore National Laboratory. He is best known for the development of inertial confinement fusion, which is a major branch of fusion power research to this day. He was also the lab's director from 1988 until 1994, when he resigned to become an associate director at large. He was awarded the Ernest Orlando Lawrence Award in 1969, the James Clerk Maxwell Prize for Plasma Physics in 1981 and the Edward Teller Award in 1991.
Heavy ion fusion is a fusion energy concept that uses a stream of high-energy ions from a particle accelerator to rapidly heat and compress a small pellet of fusion fuel. It is a subclass of the larger inertial confinement fusion (ICF) approach, replacing the more typical laser systems with an accelerator.
The history of nuclear fusion began early in the 20th century as an inquiry into how stars powered themselves and expanded to incorporate a broad inquiry into the nature of matter and energy, as potential applications expanded to include warfare, energy production and rocket propulsion.
Andrea Lynn "Annie" Kritcher is an American nuclear engineer and physicist who works at the Lawrence Livermore National Laboratory. She was responsible for the development of Hybrid-E, a capsule that enables inertial confinement fusion. She was elected Fellow of the American Physical Society in 2022.
Anklam, T.; Simon, A. J.; Powers, S.; Meier, W. R. (2 December 2010). "LIFE: The Case for Early Commercialization of Fusion Energy"(PDF). Proceedings of the Nineteenth Topical Meeting on the Technology of Fusion Energy. Archived from the original(PDF) on 4 September 2015. Retrieved 2 April 2015.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
