FLiBe

Last updated
Molten FLiBe flowing; this sample's green tint is from dissolved uranium tetrafluoride. FLiBe.png
Molten FLiBe flowing; this sample's green tint is from dissolved uranium tetrafluoride.

FLiBe is the name of a molten salt made from a mixture of lithium fluoride (LiF) and beryllium fluoride (BeF2). It is both a nuclear reactor coolant and solvent for fertile or fissile material. It served both purposes in the Molten-Salt Reactor Experiment (MSRE) at the Oak Ridge National Laboratory.

Contents

The 2∶1 molar mixture forms a stoichiometric compound, Li2[BeF4] (lithium tetrafluoroberyllate), which has a melting point of 459 °C (858 °F), a boiling point of 1,430 °C (2,610 °F), and a density of 1.94 g/cm3 (0.070 lb/cu in).

Its volumetric heat capacity, 4540 kJ/(m3.K), which is similar to that of water, more than four times that of sodium, and more than 200 times that of helium at typical reactor conditions. [1] Its specific heat capacity is 2414.17 J/(kg.K), or about 60% that of water. [2] Its appearance is white to transparent, with crystalline grains in a solid state, morphing into a completely clear liquid upon melting. However, soluble fluorides such as UF4 and NiF2, can dramatically change the salt's color in both solid and liquid state. This made spectrophotometry a viable analysis tool, and it was employed extensively during the MSRE operations. [3] [4] [5]

The eutectic mixture is slightly greater than 50%BeF2 and has a melting point of 360 °C (680 °F). [6] This mixture was never used in practice due to the overwhelming increase in viscosity caused by the BeF2 addition in the eutectic mixture. BeF2, which behaves as a glass, is only fluid in salt mixtures containing enough molar percent of Lewis base. Lewis bases, such as the alkali fluorides, will donate fluoride ions to the beryllium, breaking the glassy bonds which increase viscosity. In FLiBe, beryllium fluoride is able to sequester two fluoride ions from two lithium fluorides in a liquid state, converting it into the tetrafluoroberyllate ion [BeF4]2−. [7]

Chemistry

The chemistry of FLiBe, and other fluoride salts, is unique due to the high temperatures at which the reactions occur, the ionic nature of the salt, and the reversibility of many of the reactions. At the most basic level, FLiBe melts and complexes itself through

2 LiF(s) + BeF2(s) → 2 Li +(l) + [BeF4]2(l).

This reaction occurs upon initial melting. However, if the components are exposed to air they will absorb moisture. This moisture plays a negative role at high temperature by converting BeF2, and to a lesser extent LiF, into an oxide or hydroxide through the reactions

BeF2(l) + 2 H2O(g) ⇌ Be(OH)2(d) + 2 HF(d).

and

BeF2(l) + H2O(g) ⇌ BeO(d) + 2 HF(d).

While BeF2 is a very stable chemical compound, the formation of oxides, hydroxides, and hydrogen fluoride reduce the stability and inertness of the salt. This leads to corrosion. Its important to understand that all dissolved species in these two reactions cause the corrosion—not just the hydrogen fluoride. This is because all dissolved components alter the reduction potential or redox potential. The redox potential is an innate and measurable voltage in the salt which is the prime indicator of the corrosion potential in salt. Usually, the reaction

2 HF(g) + 2 e → 2 F + H2(g).

is set at zero volts. This reaction proves convenient in a laboratory setting and can be used to set the salt to zero through bubbling a 1:1 mixture of hydrogen fluoride and hydrogen through the salt. Occasionally the reaction:

NiF2(d) + 2 eNi(c) + 2 F.

is used as a reference. Regardless of where the zero is set, all other reactions which occur in the salt will occur at predictable, known voltages relative to the zero. Therefore, if the redox potential of the salt is close to a specific reaction's voltage, that reaction can be expected to be the predominant reaction. Therefore, it is important to keep a salt's redox potential far away from reactions which are undesirable. For example, in a container alloy of nickel, iron, and chromium, the reactions of concern would be the fluorination of container and subsequent dissolution of these metal fluorides. The dissolution of the metal fluorides then alters the redox potential. This process continues until an equilibrium between metals and salt is reached. It is essential that a salt's redox potential be kept as far away from fluorination reactions as possible, and that metals in contact with salt be as far away from the salt's redox potential as possible in order to prevent excessive corrosion.

The easiest method to prevent undesirable reactions is to pick materials whose reaction voltages are far from the redox potential of the salt in the salt's worst case. Some of these materials are tungsten, carbon, molybdenum, platinum, iridium, and nickel. Of all these materials, only two are affordable and weldable: nickel and molybdenum. These two elements were chosen as the main portion of Hastelloy-N, the material of the MSRE.

Altering the redox potential of FLiBe can be done in two ways. First, the salt can be forced by physically applying a voltage to the salt with an inert electrode. The second, more common way, is to perform a chemical reaction in the salt which occurs at the desired voltage. For example, redox potential can be altered by sparging hydrogen and hydrogen fluoride into the salt or by dipping a metal into the salt.

Coolant

As a molten salt it can serve as a coolant which can be used at high temperatures without reaching a high vapor pressure. Notably, its optical transparency allows easy visual inspection of anything immersed in the coolant as well as any impurities dissolved in it. Unlike sodium or potassium metals, which can also be used as high-temperature coolants, it does not violently react with air or water. FLiBe salt has low hygroscopy and solubility in water. [8]

Purified FLiBe. Originally ran in the secondary loop of the MSRE. Purified Flibe.JPG
Purified FLiBe. Originally ran in the secondary loop of the MSRE.

Nuclear properties

FLiBe-Solid.gif
FLiBe-Liquid.gif
Ampoules of FLiBe with uranium-233 tetrafluoride: solidified chunks contrasted with the molten liquid.

The low atomic weight of lithium, beryllium and to a lesser extent fluorine make FLiBe an effective neutron moderator. As natural lithium contains ~7.5% lithium-6, which tends to absorb neutrons producing alpha particles and tritium, nearly pure lithium-7 is used to give the FLiBe a small neutron absorption cross section; [9] e.g. the MSRE secondary coolant was 99.993% lithium-7 FLiBe. [10] When Li-7 does absorb a neutron, it nigh-instantaneously decays via successive beta- and then alpha decay into a beta particle and two alpha particles.

Beryllium will occasionally disintegrate into two alpha particles and two neutrons when hit by a fast neutron. Fluorine has a non-negligible cross section for (α,n) reactions, which needs to be taken into account when calculating neutronics. [11]

Applications

In the liquid fluoride thorium reactor (LFTR) it serves as solvent for the fissile and fertile material fluoride salts, as well as moderator and coolant.

Some other designs (sometimes called molten-salt cooled reactors) use it as coolant, but have conventional solid nuclear fuel instead of dissolving it in the molten salt.

The liquid FLiBe salt was also proposed as a liquid blanket for tritium production and cooling in the ARC fusion reactor, a compact tokamak design by MIT. [12]

See also

Related Research Articles

<span class="mw-page-title-main">Nuclear reactor</span> Device used to initiate and control a nuclear chain reaction

A nuclear reactor is a device used to initiate and control a fission nuclear chain reaction or nuclear fusion reactions. Nuclear reactors are used at nuclear power plants for electricity generation and in nuclear marine propulsion. Heat from nuclear fission is passed to a working fluid, which in turn runs through steam turbines. These either drive a ship's propellers or turn electrical generators' shafts. Nuclear generated steam in principle can be used for industrial process heat or for district heating. Some reactors are used to produce isotopes for medical and industrial use, or for production of weapons-grade plutonium. As of 2022, the International Atomic Energy Agency reports there are 422 nuclear power reactors and 223 nuclear research reactors in operation around the world.

<span class="mw-page-title-main">Redox</span> Chemical reaction in which oxidation states of atoms are changed

Redox is a type of chemical reaction in which the oxidation states of a substrate change. Oxidation is the loss of electrons or an increase in the oxidation state, while reduction is the gain of electrons or a decrease in the oxidation state.

<span class="mw-page-title-main">Neutron moderator</span> Substance that slows down particles with no electric charge

In nuclear engineering, a neutron moderator is a medium that reduces the speed of fast neutrons, ideally without capturing any, leaving them as thermal neutrons with only minimal (thermal) kinetic energy. These thermal neutrons are immensely more susceptible than fast neutrons to propagate a nuclear chain reaction of uranium-235 or other fissile isotope by colliding with their atomic nucleus.

Passive nuclear safety is a design approach for safety features, implemented in a nuclear reactor, that does not require any active intervention on the part of the operator or electrical/electronic feedback in order to bring the reactor to a safe shutdown state, in the event of a particular type of emergency. Such design features tend to rely on the engineering of components such that their predicted behaviour would slow down, rather than accelerate the deterioration of the reactor state; they typically take advantage of natural forces or phenomena such as gravity, buoyancy, pressure differences, conduction or natural heat convection to accomplish safety functions without requiring an active power source. Many older common reactor designs use passive safety systems to a limited extent, rather, relying on active safety systems such as diesel powered motors. Some newer reactor designs feature more passive systems; the motivation being that they are highly reliable and reduce the cost associated with the installation and maintenance of systems that would otherwise require multiple trains of equipment and redundant safety class power supplies in order to achieve the same level of reliability. However, weak driving forces that power many passive safety features can pose significant challenges to effectiveness of a passive system, particularly in the short term following an accident.

<span class="mw-page-title-main">Molten salt reactor</span> Type of nuclear reactor cooled by molten material

A molten salt reactor (MSR) is a class of nuclear fission reactor in which the primary nuclear reactor coolant and/or the fuel is a mixture of molten salt with a fissionable material.

A coolant is a substance, typically liquid, that is used to reduce or regulate the temperature of a system. An ideal coolant has high thermal capacity, low viscosity, is low-cost, non-toxic, chemically inert and neither causes nor promotes corrosion of the cooling system. Some applications also require the coolant to be an electrical insulator.

<span class="mw-page-title-main">Nuclear fuel</span> Material fuelling nuclear reactors

Nuclear fuel is material used in nuclear power stations to produce heat to power turbines. Heat is created when nuclear fuel undergoes nuclear fission.

<span class="mw-page-title-main">Beryllium fluoride</span> Chemical compound

Beryllium fluoride is the inorganic compound with the formula BeF2. This white solid is the principal precursor for the manufacture of beryllium metal. Its structure resembles that of quartz, but BeF2 is highly soluble in water.

<span class="mw-page-title-main">Aircraft Reactor Experiment</span> Feasibility experiment for aircraft nuclear propulsion

The Aircraft Reactor Experiment (ARE) was an experimental nuclear reactor designed to test the feasibility of fluid-fuel, high-temperature, high-power-density reactors for the propulsion of supersonic aircraft. It operated between November 8-12, 1954 at the Oak Ridge National Laboratory (ORNL) with a maximum sustained power of 2.5 megawatts (MW), and generated a total of 96 MW-hours of energy.

<span class="mw-page-title-main">FLiNaK</span>

FLiNaK is the name of the ternary eutectic alkaline metal fluoride salt mixture LiF-NaF-KF (46.5-11.5-42 mol %). It has a melting point of 454 °C and a boiling point of 1570 °C. It is used as electrolyte for the electroplating of refractory metals and compounds like titanium, tantalum, hafnium, zirconium and their borides. FLiNaK also could see potential use as a coolant in the very high temperature reactor, a type of nuclear reactor.

<span class="mw-page-title-main">Lithium fluoride</span> Chemical compound

Lithium fluoride is an inorganic compound with the chemical formula LiF. It is a colorless solid that transitions to white with decreasing crystal size. Although odorless, lithium fluoride has a bitter-saline taste. Its structure is analogous to that of sodium chloride, but it is much less soluble in water. It is mainly used as a component of molten salts. Partly because Li and F are both light elements, and partly because F2 is highly reactive, formation of LiF from the elements releases one of the highest energies per mass of reactants, second only to that of BeO.

A liquid metal cooled nuclear reactor, or LMR is a type of nuclear reactor where the primary coolant is a liquid metal. Liquid metal cooled reactors were first adapted for breeder reactor power generation. They have also been used to power nuclear submarines.

<span class="mw-page-title-main">Zirconium tetrafluoride</span> Chemical compound

Zirconium(IV) fluoride describes members of a family inorganic compounds with the formula (ZrF4(H2O)x. All are colorless, diamagnetic solids. Anhydrous Zirconium(IV) fluoride' is a component of ZBLAN fluoride glass.

<span class="mw-page-title-main">Molten-Salt Reactor Experiment</span> Nuclear reactor, Oak Ridge 1965–1969

The Molten-Salt Reactor Experiment (MSRE) was an experimental molten salt reactor research reactor at the Oak Ridge National Laboratory (ORNL). This technology was researched through the 1960s, the reactor was constructed by 1964, it went critical in 1965, and was operated until 1969. The costs of a cleanup project were estimated at about $130 million.

<span class="mw-page-title-main">Liquid fluoride thorium reactor</span> Type of nuclear reactor that uses molten material as fuel

The liquid fluoride thorium reactor is a type of molten salt reactor. LFTRs use the thorium fuel cycle with a fluoride-based molten (liquid) salt for fuel. In a typical design, the liquid is pumped between a critical core and an external heat exchanger where the heat is transferred to a nonradioactive secondary salt. The secondary salt then transfers its heat to a steam turbine or closed-cycle gas turbine.

A nuclear reactor coolant is a coolant in a nuclear reactor used to remove heat from the nuclear reactor core and transfer it to electrical generators and the environment. Frequently, a chain of two coolant loops are used because the primary coolant loop takes on short-term radioactivity from the reactor.

<span class="mw-page-title-main">Tetrafluoroberyllate</span> Anion

Tetrafluoroberyllate or orthofluoroberyllate is an anion with the chemical formula [BeF4]2−. It contains beryllium and fluorine. This fluoroanion has a tetrahedral shape, with the four fluorine atoms surrounding a central beryllium atom. It has the same size, charge, and outer electron structure as sulfate SO2−4. Therefore, many compounds that contain sulfate have equivalents with tetrafluoroberyllate. Examples of these are the langbeinites, and Tutton's salts.

<span class="mw-page-title-main">Integral Molten Salt Reactor</span>

The Integral Molten Salt Reactor (IMSR) is a nuclear power plant design targeted at developing a commercial product for the small modular reactor (SMR) market. It employs molten salt reactor technology which is being developed by the Canadian company Terrestrial Energy. It is based closely on the denatured molten salt reactor (DMSR), a reactor design from Oak Ridge National Laboratory. It also incorporates elements found in the SmAHTR, a later design from the same laboratory. The IMSR belongs to the DMSR class of molten salt reactors (MSR) and hence is a "burner" reactor that employs a liquid fuel rather than a conventional solid fuel; this liquid contains the nuclear fuel and also serves as primary coolant.

Transatomic Power was an American company that designed Generation IV nuclear reactors based on molten salt reactor (MSR) technology.

The Molten-Salt Demonstration Reactor (MSDR) was a semi-commercial-scale experimental molten salt reactor (MSR) design developed at Oak Ridge National Laboratory (ORNL).

References

  1. http://www.ornl.gov/~webworks/cppr/y2001/pres/122842.pdf Archived 2010-01-13 at the Wayback Machine CORE PHYSICS CHARACTERISTICS AND ISSUES FOR THE ADVANCED HIGH-TEMPERATURE REACTOR (AHTR), Ingersoll, Parma, Forsberg, and Renier, ORNL and Sandia National Laboratory
  2. https://inldigitallibrary.inl.gov/sites/STI/STI/5698704.pdf Engineering Database of Liquid Salt Thermophysical and Thermochemical Properties
  3. Toth, L. M. (1967). Containers for Molten Fluoride Spectroscopy.
  4. Phillip Young, Jack; Mamantov, Gleb; Whiting, F. L. (1967). "Simultaneous voltammetric generation of uranium(III) and spectrophotometric observation of the uranium(III)-uranium(IV) system in molten lithium fluoride-beryllum fluoride-zirconium fluoride". The Journal of Physical Chemistry. 71 (3): 782–783. doi:10.1021/j100862a055.
  5. Young, J. P.; White, J. C. (1960). "Absorption Spectra of Molten Fluoride Salts. Solutions of Several Metal Ions in Molten Lithium Fluoride-Sodium Fluoride-Potassium Fluoride". Analytical Chemistry. 32 (7): 799–802. doi:10.1021/ac60163a020.
  6. Williams, D. F., Toth, L. M., & Clarno, K. T. (2006). Assessment of Candidate Molten Salt Coolants for the Advanced High-Temperature Reactor (AHTR). Tech. Rep. ORNL/TM-2006/12, Oak Ridge National Laboratory.
  7. Toth, L. M.; Bates, J. B.; Boyd, G. E. (1973). "Raman spectra of Be2F73- and higher polymers of beryllium fluorides in the crystalline and molten state". The Journal of Physical Chemistry. 77 (2): 216–221. doi:10.1021/j100621a014.
  8. "Engineering Database of Liquid Salt Thermophysical and Thermochemical Properties" (PDF). Archived from the original (PDF) on August 8, 2014.
  9. "The Pea and the Beach-Ball – Energy From Thorium". 28 September 2010.
  10. "In Czech: ORNL part of nuclear R&D pact". Archived from the original on 2012-04-22. Retrieved 2012-05-13.
  11. https://www.oecd-nea.org/janisweb/book/alphas/F19/MT4/renderer/226%5B%5D
  12. Sorbom, B.N. (2015). "ARC: A compact, high-field, fusion nuclear science facility and demonstration power plant with demountable magnets". Fusion Engineering and Design. 100: 378–405. arXiv: 1409.3540 . doi:10.1016/j.fusengdes.2015.07.008. S2CID   1258716.