Solid Rocket Motor Upgrade

Last updated
Solid Rocket Motor Upgrade (SRMU)
Titan IVB core vehicle arrive at the pad at Launch Complex 40.jpg
Titan IV-B with 2 SRMU boosters
Country of originFlag of the United States (23px).png  United States
Designer Hercules
Manufacturer Alliant Techsystems
ApplicationSolid rocket booster
Predecessor UA1207
StatusRetired
Solid-fuel motor
Propellant HTPB
CasingComposite
Configuration
Nozzle ratio15.7
Performance
Thrust6.41 MN (1,440,502 lbf) average
Chamber pressure 859.5 psi (5,926 kPa)
Specific impulse, vacuum285.6 s (2.801 km/s)
Specific impulse, sea-level251.4 s (2.465 km/s)
Burn time135.7s
Thrust vectoring 6 degrees
Dimensions
Length34.26 m (1349 in)
Diameter3.2m (126 in)
Empty mass80,611 lb (36,565 kg)

The Solid Rocket Motor Upgrade (SRMU) was a solid rocket motor that was used as a booster on the Titan IVB launch vehicle. Developed by Hercules (later ATK), it was intended to be a high-performance, low-cost upgrade to the UA1207 boosters previously used on Titan IV. Wound from carbon-fibre-reinforced polymer and burning a hydroxyl-terminated polybutadiene-bound ammonium perchlorate composite propellant, it was an ambitious upgrade building on Hercules' experience developing a filament-wound case for the Space Shuttle SRB. Originally intended to fly in 1990, it instead first flew in 1997 due to a protracted development and lack of demand. The SRMU performed successfully on all of its flights.

Contents

Design

The SRMU is a three-segment solid rocket motor. Each segment has a casing wound from graphite fibre composite and an insulation system of EPDM rubber and kevlar. [1] The casing is filled with a fuel grain composed primarily of ammonium perchlorate and aluminium, joined by a HTPB binder. [2] Upon launch, the booster weighs approximately 776,000 lbs (352,000 kg). [3] The SRMU participates in vehicle control using a hydraulically driven thrust-vectoring nozzle, which can move up to 6 degrees. [4] The hydraulic system features redundant pumps that keep the fluid loop at 3,150 psi (21.7 MPa). [5] These characteristics were chosen for greater performance and higher reliability compared to its predecessor, the UA1207, which was manufactured from 7 segments and used liquid fuel injection for steering. [6] There are six stage separation motors, three fore and three aft, which push the empty casing away from the launcher's core after booster burnout. [6]

The SRMU's electrical equipment and instrumentation is located within the nosecone at the front of the booster. [4] Like the Space Shuttle's RSRM, operating voltage for the electrical system was 28V DC. [7] An electrical detonator is used to activate pyrotechnics for booster ignition and staging, and for the flight termination system, which consists of a shaped charge explosive designed to destroy the booster in flight. [7] The booster is attached to the vehicle core by a reinforced aft skirt near the base of the motor, which also transmits the thrust loads between the two structures. [6] This skirt also contains the assembly for the thrust vectoring control (TVC) system. [2] The nozzle itself is made of steel, wrapped in an epoxy composite similar to that on the motor segments. [3] Additional structural elements include steel bands at segment joins. Each segment is manufactured separately, then integrated at the launch site. [3]

As is typical for solid rocket motors, thrust varies throughout the course of the burn. The SRMU's fuel geometry is designed to generate highest thrust before 40 seconds, and to rapidly decrease thrust after 120 seconds. [3] Two SRMUs provide all of the Titan IV-B's thrust at liftoff and function as a "stage 0"; the LR87-AJ-11 on the core ignites at T+131 seconds, 15 seconds before booster separation. [6]

Development

In the wake of the 1986 Space Shuttle Challenger Disaster, in which a seal joining two solid rocket motor segments failed, destroying the vehicle and killing all 7 crew, the US Air Force was concerned about the United Technologies-built UA120 boosters used on Titan carrier rockets. [5] First flown in 1965, the UA120s were built from many segments and had a heavy thrust vectoring system that sprayed dinitrogen tetroxide into the nozzle flow to deflect thrust. Therefore, in 1987, the Air Force and the Titan's manufacturer, Martin Marietta, issued a request for proposals for a new booster to be used on Titan. [5] A fixed-price contract was awarded to Hercules Inc. for the new motor. [8]

Numerous delays took place during development. Martin Marietta changed the majority of its design requirements for the SRMU between 1988 and 1990, rendering progress slow. [9] The SRMU was the largest motor Hercules had ever built, and it was also its first use of HTPB binder. [10] [11] Early in development, a test segment was lost due to improper fuel casting. [12] In 1990, prior to the first stacking of the motor, the crane assembling the booster dropped a segment, causing it to roll away from the test area and explode. One worker was killed and nine injured. [13] The mishap also caused the first launch of a Titan IV with SRMU boosters to be delayed; originally, the new booster was expected to launch in 1991. [14] One year later, in the SRMU's first test firing, the motor exploded upon ignition. [15] The motor had to be thoroughly redesigned. In the meantime, Martin Marietta placed an order for more UA120 motors, as the SRMU would not be ready in time. At the same time, Hercules' costs severely exceeded the value of the contract it had been awarded. [16] The United States Congress in 1993 directed the Air Force to provide an additional $350 million to allow Hercules to finish work on the SRMU. [17] Before the end of 1994, the booster had finally been qualified for flight. [18]

By 1994, it had become apparent that Martin Marietta's additional order for UA1207 boosters, combined with a decline in demand for launches, was resulting in a surplus of completed Titan IV carrier rockets. [16] As a result, the SRMU would not be needed until 1997. A total of 17 flight sets of boosters were ordered; [16] the last were used on the last Titan flight in 2005. [19]

In 2000, the carbon-phenolic coated nozzle of the SRMU was redesigned. The new nozzle used new materials that were cleaner than those previously used, which were incompliant with new environmental regulations. [20]

See also

Related Research Articles

<span class="mw-page-title-main">Solid-propellant rocket</span> Rocket with a motor that uses solid propellants

A solid-propellant rocket or solid rocket is a rocket with a rocket engine that uses solid propellants (fuel/oxidizer). The earliest rockets were solid-fuel rockets powered by gunpowder; The inception of gunpowder rockets in warfare can be credited to the ancient Chinese, and in the 13th century, the Mongols played a pivotal role in facilitating their westward adoption.

<span class="mw-page-title-main">Titan (rocket family)</span> Family of launch vehicles used in U.S. Air Force and space programs (1959–2005)

Titan was a family of United States expendable rockets used between 1959 and 2005. The Titan I and Titan II were part of the US Air Force's intercontinental ballistic missile (ICBM) fleet until 1987. The space launch vehicle versions contributed the majority of the 368 Titan launches, including all the Project Gemini crewed flights of the mid-1960s. Titan vehicles were also used to lift US military payloads as well as civilian agency reconnaissance satellites and to send interplanetary scientific probes throughout the Solar System.

<span class="mw-page-title-main">Alliant Techsystems</span> American aerospace, defense, and arms firm (1990–2015)

Alliant Techsystems Inc. (ATK) was an American aerospace and arms manufacturer headquartered in Arlington County, Virginia. The company operated across 22 states, Puerto Rico, and internationally. ATK revenue in fiscal year 2014 was about US$4.8 billion.

<span class="mw-page-title-main">Space Shuttle Solid Rocket Booster</span> Solid propellant rocket used to launch the Space Shuttle orbiter

The Space Shuttle Solid Rocket Booster (SRB) was the first solid-propellant rocket to be used for primary propulsion on a vehicle used for human spaceflight. A pair of these provided 85% of the Space Shuttle's thrust at liftoff and for the first two minutes of ascent. After burnout, they were jettisoned and parachuted into the Atlantic Ocean where they were recovered, examined, refurbished, and reused.

<span class="mw-page-title-main">Titan IV</span> Expendable launch system used by the US Air Force

Titan IV was a family of heavy-lift space launch vehicles developed by Martin Marietta and operated by the United States Air Force from 1989 to 2005. Launches were conducted from Cape Canaveral Air Force Station, Florida and Vandenberg Air Force Base, California.

<span class="mw-page-title-main">Titan IIIC</span> Expendable launch system used by the US Air Force

The Titan IIIC was an expendable launch system used by the United States Air Force from 1965 until 1982. It was the first Titan booster to feature large solid rocket motors and was planned to be used as a launcher for the Dyna-Soar, though the spaceplane was cancelled before it could fly. The majority of the launcher's payloads were DoD satellites, for military communications and early warning, though one flight (ATS-6) was performed by NASA. The Titan IIIC was launched exclusively from Cape Canaveral while its sibling, the Titan IIID, was launched only from Vandenberg AFB.

<span class="mw-page-title-main">Graphite-Epoxy Motor</span> American solid rocket booster

The Graphite-Epoxy Motor (GEM) is a family of solid rocket boosters developed in the late 1980s and used since 1990. GEM motors are manufactured with carbon-fibre-reinforced polymer casings and a fuel consisting of HTPB-bound ammonium perchlorate composite propellant. GEM is produced by Northrop Grumman Space Systems. GEM boosters are used on the Atlas V and were previously used on the Delta II, Delta III, and Delta IV launch vehicles. A new variant, the GEM 63XL, flew as part of the Vulcan Centaur launch vehicle on 8 January 2024.

<span class="mw-page-title-main">Shuttle-derived vehicle</span> Launch vehicle built from Space Shuttle components

Shuttle-derived vehicles (SDV) are space launch vehicles and spacecraft that use components, technology, and infrastructure originally developed for the Space Shuttle program.

<span class="mw-page-title-main">Ares I</span> Canceled NASA rocket key to the Constellation program

Ares I was the crew launch vehicle that was being developed by NASA as part of the Constellation program. The name "Ares" refers to the Greek deity Ares, who is identified with the Roman god Mars. Ares I was originally known as the "Crew Launch Vehicle" (CLV).

<span class="mw-page-title-main">Athena (rocket family)</span> Lockheed Martin expendable launch system

Athena was a 1990s Lockheed Martin expendable launch system which underwent several name changes in its lifetime.

<span class="mw-page-title-main">Saturn II</span> Proposed NASA heavy-lift launch vehicle

The Saturn II was a series of American expendable launch vehicles, studied by North American Aviation under a NASA contract in 1966, derived from the Saturn V rocket used for the Apollo lunar program. The intent of the study was to eliminate production of the Saturn IB, and create a lower-cost heavy launch vehicle based on Saturn V hardware. North American studied three versions with the S-IC first stage removed: the INT-17, a two-stage vehicle with a low Earth orbit payload capability of 47,000 pounds (21,000 kg); the INT-18, which added Titan UA1204 or UA1207 strap-on solid rocket boosters, with payloads ranging from 47,000 pounds (21,000 kg) to 146,400 pounds (66,400 kg); and the INT-19, using solid boosters derived from the Minuteman missile first stage.

<span class="mw-page-title-main">Castor (rocket stage)</span> Solid-fuel orbital vehicle component

Castor is a family of solid-fuel rocket stages and boosters built by Thiokol and used on a variety of launch vehicles. They were initially developed as the second-stage motor of the Scout rocket. The design was based on the MGM-29 Sergeant, a surface-to-surface missile developed for the United States Army at the Jet Propulsion Laboratory.

The expansion-deflection nozzle is a rocket nozzle which achieves altitude compensation through interaction of the exhaust gas with the atmosphere, much like the plug and aerospike nozzles.

<span class="mw-page-title-main">Fastrac (rocket engine)</span> Pump-fed liquid rocket engine developed by NASA for use on small inexpensive, expendable rockets

Fastrac was a turbo pump-fed, liquid rocket engine. The engine was designed by NASA as part of the low cost X-34 Reusable Launch Vehicle (RLV) and as part of the Low Cost Booster Technology project. This engine was later known as the MC-1 engine when it was merged into the X-34 project.

The Star is a family of US solid-propellant rocket motors originally developed by Thiokol and used by many space propulsion and launch vehicle stages. They are used almost exclusively as an upper stage, often as an apogee kick motor.

<span class="mw-page-title-main">P80 (rocket stage)</span> Solid-fuel first-stage rocket motor used on the ESA Vega

P80 is a solid-fuel first-stage rocket motor used on the European Space Agency Vega rocket. It was the world's largest and most powerful one-piece solid-fuel rocket engine, being replaced by the larger P120C on 13 July 2022.

<span class="mw-page-title-main">UA120</span>

UA120 was a family of American solid rocket boosters, manufactured by the Chemical Systems Division of United Aircraft. Several variants existed, with a varying number of segments.

<span class="mw-page-title-main">OmegA</span> Canceled US launch vehicle

OmegA was a medium-lift to heavy-lift launch vehicle concept that spent several years in development by Northrop Grumman during 2016–2020, with that development substantially funded by the U.S. government. OmegA was intended for launching U.S. national security satellites, as part of the U.S. Department of the Air Force National Security Space Launch (NSSL) replacement program.

<span class="mw-page-title-main">Studied Space Shuttle designs</span> Launch vehicle study

During the lifetime of the Space Shuttle, Rockwell International and many other organizations studied various Space Shuttle designs. These involved different ways of increasing cargo and crew capacity, as well as investigating further reusability. A large focus of these designs were related to developing new shuttle boosters and improvements to the central tank, but also looked to expand NASA's ability to launch deep space missions and build modular space stations. Many of these concepts and studies would shape the concepts and programs of the 2000s such as the Constellation, Orbital Space Plane Program, and Artemis program.

<span class="mw-page-title-main">Aerojet 260</span> Experimental solid rocket motor

The Aerojet 260 was an experimental solid rocket motor constructed and tested in the mid-1960s by Aerojet for NASA.

References

  1. Chang, I-Shih; Patel, N. R.; Yang, S. (1995). "Titan IV motor failure and redesign analyses". Journal of Spacecraft and Rockets. 32 (4): 612–618. Bibcode:1995JSpRo..32..612C. doi:10.2514/3.26661. ISSN   0022-4650.
  2. 1 2 Wilson, W.; Anderson, J.; Meyden, M. (1992-07-06), "Titan IV SRMU PQM-1 overview", 28th Joint Propulsion Conference and Exhibit, Joint Propulsion Conferences, American Institute of Aeronautics and Astronautics, doi:10.2514/6.1992-3819 , retrieved 2022-05-10
  3. 1 2 3 4 "ATK Product Catalog" (PDF). ATK. Archived from the original (PDF) on July 30, 2018. Retrieved July 24, 2014.
  4. 1 2 Foote, Jeffrey; Foote, Jeffrey (1997-07-06), "Titan IV Solid Rocket Motor Upgrade Program at Alliant Techsystems Inc", 33rd Joint Propulsion Conference and Exhibit, Joint Propulsion Conferences, American Institute of Aeronautics and Astronautics, doi:10.2514/6.1997-2991 , retrieved 2022-05-11
  5. 1 2 3 Quick-Reaction Report on the Management of the Titan IV Solid Rocket Motor Upgrade Subcontract (Report). 1992-09-02. Archived from the original on May 10, 2022.
  6. 1 2 3 4 Rudman, Thomas; De, Duane; Earl, Steve (1998-07-13), "Titan IVB, SRMU and Centaur propulsion systems", 34th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, Joint Propulsion Conferences, American Institute of Aeronautics and Astronautics, doi:10.2514/6.1998-3194 , retrieved 2022-05-10
  7. 1 2 Saemisch, Michael; Jackson, Donald; Saemisch, Michael; Jackson, Donald (1997-07-06), "Lessons learned from Titan IV SRMU ordnance programs", 33rd Joint Propulsion Conference and Exhibit, Joint Propulsion Conferences, American Institute of Aeronautics and Astronautics, doi:10.2514/6.1997-2957 , retrieved 2022-05-10
  8. Ap (1987-10-21). "COMPANY NEWS; HERCULES WINS MARIETTA CONTRACT". The New York Times. ISSN   0362-4331 . Retrieved 2022-05-11.
  9. "FIRM WITHHELD DATA, HERCULES SAYS". Deseret News. 1992-02-08. Retrieved 2022-05-11.
  10. "HERCULES FUELS INITIAL TITAN IV SEGMENT". Deseret News. 1989-12-07. Retrieved 2022-05-11.
  11. "HERCULES: BOOMING COMPANY CELEBRATES 75TH YEAR". Deseret News. 1988-10-16. Retrieved 2022-05-11.
  12. "HERCULES PROBES FAILURE OF ADHESION IN TITAN IV SOLID ROCKET MOTOR OFFICIALS SAY 'ANOMALY' WON'T CAUSE SETBACK". Deseret News. 1990-01-21. Retrieved 2022-05-10.
  13. Chandler, John (1991-05-29). "Titan 4 Motor Explosion Blamed on Design Flaw". Los Angeles Times. Retrieved 2022-05-10.
  14. "TITAN MOTOR ACCIDENT DEALT YET ANOTHER BLOW TO HERCULES". Deseret News. 1990-09-14. Retrieved 2023-05-03.
  15. "HERCULES SAYS ROCKET BLAST WON'T STOP TITAN IV PROJECT". Deseret News. 1991-04-10. Retrieved 2022-05-11.
  16. 1 2 3 "Titan IV Requirements". Department of Defense Office of Inspector General. 1994-04-21. Retrieved 2022-05-11.
  17. Murtha, John P. (1992-10-06). "H.R.5504 - 102nd Congress (1991-1992): Department of Defense Appropriations Act, 1993". www.congress.gov. Retrieved 2022-05-11.
  18. Chamberlain, Roger, "Paper Session II-C - Titan IV Heavy-Lift Space Launch System Evolution" (1994). The Space Congress® Proceedings. 3. https://commons.erau.edu/space-congress-proceedings/proceedings-1994-31st/april-27-1994/3
  19. "Spaceflight Now | Titan Launch Report | Goodbye, Titan". www.spaceflightnow.com. Retrieved 2022-05-11.
  20. "Spaceflight Now | Breaking News | Titan 4 solid rocket motor test firing successful". spaceflightnow.com. Retrieved 2022-05-11.