The Mazda RX-7 is a front-engine, rear-wheel-drive, rotary engine-powered sports car that was manufactured and marketed by Mazda from 1978 until 2002 across three generations, all of which made use of a compact, lightweight Wankel rotary engine.
The first-generation RX-7, sometimes referred to as the SA (early) and FB (late), is a two-seater two-door hatchbackcoupé. It featured a 12A carbureted rotary engine as well as the option for a 13B rotary engine with electronic fuel injection in later years.
The second-generation RX-7, sometimes referred to as the FC, was offered as a two-seater coupé with a 2+2 option available in some markets, as well as in a convertible body style. This was powered by the 13B rotary engine, offered in naturally aspirated or turbocharged forms.
The third-generation RX-7, sometimes referred to as the FD, was offered a 2+2-seater coupé with a limited run of a two-seater option. Some markets were only available as a two-seater. It featured a sequentially turbocharged 13B REW engine.
More than 800,000 RX-7s were manufactured over its lifetime.[1]
Series 1 (produced from 1978 until 1980) is commonly referred to as the "SA22C" from the first alphanumeric of the vehicle identification number. Mazda's internal project number for what was to become the RX-7 was X605. In Japan, it was introduced in March 1978, replacing the Savanna RX-3, and joined Mazda's only other remaining rotary engine-powered products, called the Cosmo which was a two-door luxury coupé, and the Luce luxury sedan.
The lead designer at Mazda was Matasaburo Maeda (前田 又三郎, Maeda Matasaburō), whose son, Ikuo[ja], would go on to design the Mazda2 and the RX-7's successor, the RX-8.[2] The transition of the Savanna to a sports car appearance reflected products from other Japanese manufacturers. The advantage the RX-7 had was its minimal size and weight, and the compact rotary engine installed behind the front axle helped balance the front and rear weight distribution, which provided a low center of gravity.
In May 1980, Mazda introduced a limited production run of special North American models known as the Leathersport Models. This package was essentially an uprated GS model with added LS badges on each B-pillar, special stripes on the exterior, and LS-only gold anodized wheels (with polished outer face and wheel rim). All LS editions came equipped with special LS-only full brown leather upholstery, leather-wrapped steering wheel, leather-wrapped shift knob, removable sunroof, LS-specific four-speaker AM/FM stereo radio with power antenna (though listed as a six-speaker stereo, as the two rear dual voice coil speakers were counted as four speakers in total), remote power door side mirrors, and other standard GS equipment. Two primary options were also available; a three-speed JATCO 3N71B automatic transmission and air conditioning. The dealer could add other GS options such as a cassette tape deck, splash guards, padded center console arm rest, and others. The LS model was only ever available in three different exterior colors: Aurora White, Brilliant Black, and Solar Gold. No official production records are known to exist or to have been released. This series of RX-7 had exposed steel bumpers and a high-mounted indentation-located rear license plate, called by Werner Buhler of Road & Track magazine a "Baroque depression."
Series 2 (1981–1983)
Mazda RX-7 Series 2 GSL (US; 1983)
The Series 2, referred to as the FB (produced from 1981 to 1983), had integrated plastic-covered bumpers, wide black rubber body side moldings, wraparound taillights and updated engine control components. While marginally longer overall, the new model was 135lb (61kg) lighter in federalized trim.[3] The four-speed manual option was dropped for 1981 as well, while the gas tank grew larger and the dashboard was redesigned, including a shorter gear stick mounted closer to the driver.[3] In 1983, the 130mph (209km/h) speedometer returned for the RX-7. The GSL package provided optional four-wheel disc brakes, front ventilated (Australian model) and clutch-type rear limited-slip differential (LSD). This revision of the SA22 was known in North America as the "FB" after the US Department of Transportation mandated 17 digit Vehicle Identification Number changeover. For various other markets worldwide, the 1981–1985 RX-7 retained the 'SA22C' VIN prefix. In the UK, the 1978–1980 series 1 cars carried the SA code on the VIN but all later cars (1981–1983 series 2 and 1984–1985 series 3) carried the FB code and these first-generation RX-7s are known as the "FB" only in Northern America.
In Japan, a very well appointed version similar to the export market GSL arrived late in 1982, called the SE-Limited. This model received two-tone paint, alloy wheels shaped like the Wankel rotor, all-wheel disc brakes, limited-slip differential, and a full leather interior. It also had the latest iteration of the 12A rotary engine, the RE-6PI with variable induction port system and 140PS (103kW; 138hp).[4]
In Europe, the FB was mainly noticed for having received a power increase from the 105PS (77kW) of the SA22; the 1981 RX-7 now had 115PS (85kW) on tap. European market cars also received four-wheel disc brakes as standard.[5]
In 1984 Mazda Australia decided to produce a convertible by joining a RX7 front body with a 626 coupee rear end. To ensure rigidity, steel channel beams were welded to the floor pan. Due to the added weight, the engine used was the Japanese model 12AT introduced in 1983.rated at 121kw@ 6500rpm. It was planned and budgeted to build eighty cars a year. However after the first production run of six, Mazda Japan became aware of the project and ended it. intending in 1985 to introduce the Second Generation increased size RX7 with the larger, more powerful 13B engine. This would include a convertible model for worldwide sales. Thus, the Series 2 convertible is the rarest Mazda car built.
The Series 3 (produced 1984–1985) featured an updated lower front fascia. North American models received a different instrument cluster. GSL package was continued into this series, but Mazda introduced the GSL-SE sub-model. The GSL-SE had a fuel injected1,308cc (1.3L)13B RE-EGI engine rated at 135hp (101kW; 137PS) and 133lb⋅ft (180N⋅m). GSL-SE models had much the same options as the GSL (clutch-type rear LSD and rear disc brakes), but the brake rotors were larger, allowing Mazda to use the more common lug nuts (versus bolts), and a new bolt pattern of 4x114.3mm (4x4.5"). Also, they had upgraded suspension with stiffer springs and shocks. The external oil cooler was reintroduced, after being dropped in the 1983 model-year for the controversial "beehive" water-oil heat exchanger.
The 1984 RX-7 GSL has an estimated 29 MPG (8.11 litres/100km) highway/19 MPG (12.37 L/100km) city. According to Mazda, its rotary engine, licensed by NSU-Wankel allowed the RX-7 GSL to accelerate from 0 to 80 km/h (50 mph) in 6.3 seconds.
In 1985, Mazda introduced the RX-7 Finale in Australia. This was the last of the series and brought out in limited numbers. The Finale featured power options and a brass plaque mentioning the number the car was as well as "Last of a legend" on the plaque. The finale had special stickers and a blacked out section between the window & rear hatch.
The handling and acceleration of the car were noted to be of a high caliber for its day.[citation needed] The RX-7 had "live axle" 4-link rear suspension with Watt's linkage, a 50:50 front and rear weight distribution, and weighed under 1,100kg (2,425lb). It was the lightest generation of the RX-7 ever produced. 12A-powered models accelerated from 0–97km/h (60mph) in 9.2 seconds, and turned 0.779g (7.64m/s²) laterally on a skid pad. The 1,146cc (1.1L)12A engine was rated at 100hp (75kW; 101PS) at 6,000 rpm in North American models, allowing the car to reach speeds of over 190km/h (120mph). Because of the smoothness inherent in the Wankel rotary engine, little vibration or harshness was experienced at high engine speeds, so a buzzer was fitted to the tachometer to warn the driver when the 7,000 rpm redline was approaching.
The 12A engine has a long thin shaped combustion chamber, having a large surface area in relation to its volume. Therefore, combustion is cool, giving few oxides of nitrogen. However, the combustion is also incomplete, so there are large amounts of partly burned hydrocarbons and carbon monoxide. The exhaust is hot enough for combustion of these to continue into the exhaust. An engine-driven pump supplies air into the exhaust to complete the burn of these chemicals. This is done in the "thermal reactor" chamber where the exhaust manifold would normally be on a conventional engine. Under certain conditions, the pump injects air into the thermal reactor and at other times air is pumped through injectors into the exhaust ports. This fresh air is needed for more efficient and cleaner-burning of the air/fuel mixture.[6]
Options and models varied from country to country. The gauge layout and interior styling in the Series 3 was only changed for the North American models. Additionally, North America was the only market to have offered the first generation of the RX-7 with the fuel-injected 13B, model GSL-SE. Sales of the first-generation RX-7 were strong, with a total of 474,565 cars produced; 377,878 (nearly eighty percent) were sold in the United States alone.
RX-7 Turbo
Mazda Savanna RX-7 Turbo
Following the introduction of the first turbocharged rotary engine in the Luce/Cosmo, a similar, also fuel injected and non-intercooled 12A turbocharged engine was made available for the top-end model of the Series 3 RX-7 in Japan. It was introduced in September 1983.[7] The engine was rated at 165PS (121kW) (JIS) at 6,500rpm. While the peak power figures were only slightly higher than those of the engine used in the Luce/Cosmo, the new "Impact Turbo" was developed specifically to deal with the different exhaust gas characteristics of a rotary engine. Both rotor vanes of the turbine were remodeled and made smaller, and the turbine had a twenty percent higher speed than a turbo intended for a conventional engine.[8] The Savanna Turbo was short-lived, as the next generation of the RX-7 was about to be introduced.
Mazda RX-7 Turbo (JDM), note the intercooler scoop on the bonnet distinguishing it from the naturally aspirated models
The second-generation RX-7 (sometimes referred to as "FC", VIN begins JM1FC3 or JMZFC1), still known as the Mazda Savanna RX-7 in Japan, featured a complete restyling much like similar sports cars of the era such as the Nissan 300ZX. Mazda's development team, led by Chief Project Engineer Akio Uchiyama (内山 昭朗), chose to focus on the American market when designing the FC, where the majority of first-generation of the RX-7 models had been sold. The team drew inspiration from successful sports cars that were popular at the time, such as studying the suspension design of the Porsche 928.[9]
While the first-generation RX-7 was a purer sports car, the second-generation RX-7 tended toward the softer sport-tourer trends of its day, sharing some similarities with the HB series Cosmo. Handling was much improved, with less of the oversteer tendencies of the previous version. The rear end design was vastly improved from the SA22's live rear axle to a more modern, Independent Rear Suspension (rear axle). Steering was more precise, with rack and pinion steering replacing the old recirculating-ball steering of the SA22. Disc brakes also became standard, with some models (S4: Sport, GXL, GTU, Turbo II, Convertible; S5: GXL, GTUˢ, Turbo, Convertible) offering four-piston front brakes. The rear seats were optional in some models of the FC RX-7, but are not commonly found in the American Market. Mazda also introduced Dynamic Tracking Suspension System (DTSS) in the FC. The revised independent rear suspension incorporated special toe control hubs which were capable of introducing a limited degree of passive rear steering under cornering loads. The DTSS worked by allowing a slight amount of toe-out under normal driving conditions but induced slight toe-in under heavier cornering loads at around 0.5g or more; toe-out in the rear allows for a more responsive rotation of the rear, but toe-in allowed for a more stable rear under heavier cornering. Another new feature was the Auto Adjusting Suspension (AAS). The system changed damping characteristics according to the road and driving conditions. The system compensated for camber changes and provided anti-dive and anti-squat effects.
In Japan, a limited edition of the second-generation RX-7 called Infini was available with production limited to only 600 cars for each year. Some special noted features for all Infini series are: infini logo on the rear, upgraded suspension, upgraded ECU, higher power output of the engine, reduced weight, 15-inch BBS aluminum alloy wheels, Infini logo steering wheel, aero bumper kits, bronze-colored window glass, floor bar on the passenger side, aluminum bonnet with scoop, flare, and holder. The car was thought as the pinnacle of the RX-7 series (until the introduction of the third generation RX-7). The Infini IV came with other special items such as black bucket seats, 16-inch BBS wheels, Knee pads, and all the other items mentioned before. There are differing years for the Infini, which denoted the series. Series I was introduced in 1987, Series II was introduced in 1988, Series III was introduced in 1989, and Series IV was introduced in 1990. Series I and II came in White or Black exterior colour, Series III came in Shade Green only, and Series IV came in Shade Green or Noble Green exterior colours. There are only minor differences between the Series models, the biggest change which was from the Series I and II being an S4 and the Series III and IV being an S5.
The Turbo II model uses a turbocharger with a twin-scroll design. The smaller primary chamber is engineered to cancel the turbo lag at low engine speeds. At higher revolutions, the secondary chamber is opened, pumping out 33 percent more power than the naturally aspirated counterpart. The Turbo II also has an air-to-air intercooler which has a dedicated intake on the hood. The intake is slightly offset toward the left side of the hood. In the Japanese market, only the turbocharged engine was available; the naturally-aspirated version was only available for select export markets. This can be attributed to insurance companies in many Western nations penalizing turbocharged cars (thus restricting potential sales). The Japanese market car produces 185PS (136kW) in the original version; this engine was upgraded to 205PS (151kW) in April 1989 as part of the Series 5 facelift. The limited edition, two-seater Infini model received a 215PS (158kW) version beginning in June 1990, thanks to an upgraded exhaust system and high-octane fuel.
Australian Motors Mazda introduced a limited run of 250 'Sports' model Series 4 RX-7s; each with no power steering, power windows or rear wiper as an attempt to reduce the weight of the car.
The Haraguchi RX-7 is a legendary vehicle in the world of drifting, often hailed as an iconic representation of the drift culture that emerged in the 1990s. Built by Mitsuru Haraguchi between 1989 and 1993, this Series 2 RX-7 became famous for its unique style and performance, making it one of the earliest examples of what enthusiasts would come to call a "HotBoi" drift car—a term used to describe cars modified for drifting with an emphasis on aesthetic appeal. Mitsuru Haraguchi was not just a driver; he was a key figure in the underground drifting scene in Japan. The RX-7, with its lightweight body and rotary engine, proved to be an ideal platform for the kind of driving that would push the envelope in terms of control and style. The car was extensively modified for performance, featuring upgrades to its suspension, tires, and engine to suit the demands of drifting. The RX-7's aesthetic was also significant. It showcased a vibrant design that captured the spirit of the drifting scene, often adorned with bold graphics and a striking color scheme that made it instantly recognizable. Tragically, the Haraguchi RX-7 met an unfortunate fate when it was crashed in 1999, yet its impact on the drifting community has been profound. The crash, rather than marking the end of its story, solidified its legendary status. It has since been celebrated in various media, including magazines, videos, and online forums, where enthusiasts pay homage to its legacy. Even today, the legacy of the Haraguchi RX-7 influences the design and customization of drift cars around the world. It remains a symbol of innovation within the drifting culture, representing the fusion of performance driving with creative expression through automotive art.
Convertible
1989 Mazda RX-7 convertible (FC)
Mazda introduced a convertible version of the RX-7, the FC3C, in 1988 with a naturally aspirated engine—introduced to the US market with ads featuring actor James Garner, at the time featured in many Mazda television advertisements. Only about 22,000 convertibles were built.
The convertible featured a removable rigid section over the passengers and a folding fabric rear section with heated rear glass window. Power operated, lowering the top required unlatching two header catches, power lowering the top, exiting the car (or reaching over to the right-side latch), and folding down the rigid section manually. Mazda introduced with the convertible the first integral windblocker, a rigid panel that folded up from behind the passenger seats to block unwanted drafts from reaching the passengers—thereby extending the driving season for the car with the top retracted.[10] The convertible also featured optional headrest-mounted audio speakers and a folding leather snap-fastened tonneau cover. The convertible assembly was precisely engineered and manufactured, and dropped into the ready body assembly as a complete unit—a first in convertible production.
Production ceased in 1991 after Mazda marketed a limited run of 500 examples for 1992 for the domestic market only. In markets outside the US, only the turbocharged version of the convertible was available.
North America
The Series 4 (produced for the 1986 through the 1988 model years) was available with a naturally aspirated, fuel injected13B-VDEI producing 146hp (109kW; 148PS) in North American spec. An optional turbocharged model, known as the Turbo II in the American market, was rated at 182hp (136kW; 185PS) and 183lb⋅ft (248N⋅m) of torque at 3,500 rpm. The turbo model was introduced at the Chicago Auto Show in February 1986, with a target of 20 percent of overall RX-7 sales.[11]
The Series 5 (1989–1992) featured updated styling and better engine management, as well as lighter rotors and a higher compression ratio 9.7:1 for the naturally aspirated model, and 9.0:1 for the turbo model. The naturally aspirated Series5's 13B-DEI engine was rated at 160hp (119kW; 162PS), while the Series5 Turbo was rated at 200hp (149kW; 203PS) at 6,500 rpm and 195lb⋅ft (264N⋅m) of torque at 3,500 rpm.
Mazda sold 86,000 RX-7s in the US alone in 1986, its first model year, with sales peaking in 1988.
1988 10th Anniversary RX-7
Mazda RX-7 10th Anniversary Edition
Mazda introduced the 10th Anniversary RX-7 in 1988 as a limited production model based on the RX-7 Turbo II. Production was limited to 1,500 units. The 10th Anniversary RX-7 features a Crystal White monochromatic paint scheme with matching white body side moldings, tail light housings, mirrors and 16-inch alloy seven-spoke wheels. There were two "series" of 10th Anniversary models, with essentially a VIN-split running production change between the two. The most notable difference between the series can be found on the exterior- the earlier "Series I" cars had a black "Mazda" logo decal on the front bumper cover, whereas most if not all "Series II" cars did not have the decal. Series II cars also received the lower seat cushion height/tilt feature that Series I cars lacked. Another distinctive exterior feature is the bright gold rotor-shaped 10th Anniversary Edition badge on the front fenders (yellow-gold on the Series II cars). A distinctive 10th Anniversary package feature is the all black leather interior (code D7), which included not just the seats, but the door panel inserts as well and a leather-wrapped MOMO steering wheel (with 10th Anniversary Edition embossed horn button) and MOMO leather-wrapped shift knob with integrated boot. All exterior glass is bronze tinted (specific in North America to only the 10th Anniversary), and the windshield was equipped with the embedded secondary antenna also found on some other select models with the upgraded stereo packages. Other 10th Anniversary Edition specific items were headlight washers (the only RX-7 in the US market that got this feature), glass breakage detectors added to the factory alarm system, 10th Anniversary Edition logoed floor mats, 10th Anniversary Edition embroidered front hood protector and accompanying front end mask (or "bra"), and an aluminum under pan.[12][13]
GTUˢ (1989–1990)
In 1989, with the introduction of the facelifted FC RX-7, and to commemorate the RX-7s 8 straight wins in the IMSA GTU class from 1980 to 1987, Mazda introduced a limited model labeled the GTUˢ. Starting with the lightweight base model GTU, the GTUˢ added items found on the Turbo model such as four-piston front brakes, ventilated rear brake rotors, vehicle speed-sensing power steering, one-piece front chin spoiler, cloth-covered Turbo model seats, leather-wrapped steering wheel, 16-inch wheels, 205/55VR tires, and a GTUˢ-only 4.300 viscous-type limited-slip differential (all other FC LSD's were 4.100). This allowed quicker acceleration from the naturally aspirated 13B rotary engine. Although it has been rumored that Mazda built between 100 and 1100 GTUˢ' between 1989 and 1990, there is no official documentation from Mazda on how many have been built. The most reliable way to determine a GTUˢ is by taking the VIN to a Mazda dealer and they can look to see if the internal coding for the car comes up as a GS model designation.[14]
The winning concept design for the FD RX-7, designed by Wu-Huang Chin at Mazda's Design Center in IrvineRear view
The third-generation RX‑7, (sometimes referred to as FD, chassis code FD3S for Japan and JM1FD for the North America), featured an updated body design. Announced in October 1991, production began later that month before going on sale in December in the domestic Japanese market. Left-Hand-Drive export production began shortly after. The 13B-REW engine was the first-ever mass-produced sequential twin-turbocharger system to be exported from Japan,[17] boosting power to 255PS (188kW; 252hp) in 1992 and finally to 280PS (206kW; 276hp) by the time production ended in Japan in 2002.
For the third-generation RX-7, Mazda organized an internal design competition between its four design studios in Hiroshima, Yokohama, Irvine, and Europe.[18] The winning design came from their Design Center in Irvine and was designed by Taiwanese automotive artist Wu-huang Chin (秦無荒), who also worked on the Mazda MX-5 Miata, with help from Tom Matano.[19] The interior design, though, originated from the Hiroshima design proposal. Mazda's chief designer Yoichi Sato (佐藤 洋一, Satō Yōichi) then helped take the concept design to its final production form.[9]
In Japan, sales were affected by this series' non-compliance with Japanese dimension regulations and Japanese buyers paid annual taxes for the car's non-compliant width. As the RX‑7 was now considered an upper-level luxury sports car due to the increased width dimensions, Mazda also offered two smaller offerings, the Eunos Roadster, and the Eunos Presso hatchback.
The sequential twin-turbocharging system, introduced in 1992, was extremely complex and was developed with the aid of Hitachi. It was previously used on the exclusive-to-Japan Cosmo JC Series. The system used two turbochargers, one to provide 10psi (0.69bar) of boost from 1,800rpm. The second turbocharger activated in the upper half of the rpm range, during full-throttle acceleration – at 4,000rpm to maintain 10psi (0.69bar) until redline.[20] The changeover process occurred at 4,500 rpm, with a momentary dip in pressure to 8psi (0.55bar),[21] and provided semi-linear acceleration from a wide torque curve throughout the entire rev range under normal operation.
Under high-speed-driving conditions, the changeover process produced a significant increase in power output and forced technical drivers to adjust their driving style to anticipate and mitigate any over-steer during cornering.[citation needed] The standard turbo control system used 4 control solenoids, 4 actuators, both a vacuum and pressure chamber, and several feet of preformed vacuum/pressure hoses, all of which were prone to failure in part due to complexity and the inherent high temperatures of the rotary engine.[21]
Information about various trims and models is listed as follows:
RX-7 Spirit Type R A-spec with pop-up headlights raised
Series 6 was exported throughout the world and sold in larger numbers than in later years. In Japan, Mazda sold the RX-7 through its ɛ̃fini brand as the ɛ̃fini RX-7. Models in Japan included the Type S, the base model, Type R, the lightweight sports model, Type RZ, Type RB, A-spec and the Touring X, which came with a four-speed automatic transmission.[23] The RX-7 was sold in 1993–1995 in the U.S. and Canada. The Series 6 was rated at 255PS (188kW; 252hp) and 294N⋅m (217lb⋅ft).
North American market
At launch, three option packages were offered; the unlabeled base model, the Touring and the R1 (renamed R2 in 1994). All cars were only available as a two-seater unlike the previous generation which was a 2+2 configuration in North America. All cars were equipped with the same sequential twin-turbo 13B REW engine. A five-speed manual transmission was standard and a 4-speed automatic was available on the base model and Touring package. A driver-side airbag and anti-lock brakes are standard as well. The Touring package included a glass moonroof, fog lights, leather seats, a rear window wiper and a Bose Acoustic Wave music system with CD player.[21] The R1 (R2 in 1994–95) model featured upgraded springs, Bilstein shocks, an additional engine oil cooler, an aerodynamics package comprising a front lip and rear wing, suede seats and Pirelli Z-rated tires. Cruise control was deleted on the R1.[24] The R2 differed from the R1 in that it had slightly softer suspension.[21]
In 1994, the interior received a small update to include a passenger-side air bag, and a PEG (popular equipment group) package was offered. The PEG package featured leather seats, a rear cargo cover and a power steel sunroof. It did not include the fog lights or Bose stereo of the touring package. An automatic transmission was not available with the PEG.
In 1995, the Touring package was replaced by the PEP (popular equipment package). The PEP included a rear wing, leather seats, sunroof and fog lights, but didn't have the Bose Stereo nor the rear window wiper.[21] An estimated 500 RX-7s were produced for the 1995 model year.[25] This would be the final year of RX-7 production for North America, as it was discontinued due to slow sales.
Australian market
A special high-performance version of the RX-7 was introduced in Australia in 1995, named the RX-7 SP. This model was developed to achieve homologation for racing in the Australian GT Production Car Series and the Eastern Creek 12 Hour production car race.[26] An initial run of 25 cars were made, and later an extra 10 were built by Mazda due to demand.[27] The RX-7 SP was rated at 277PS (204kW; 273hp) and 357N⋅m (263lb⋅ft) of torque, a substantial increase over the standard model. Other changes included a race-developed carbon fiber nose cone and rear spoiler, a carbon fibre 120L (32USgal) fuel tank (as opposed to the 76L (20USgal) tank in the standard car), a 4.3:1 final drive ratio, 17-inch wheels, larger brake rotors and calipers. A "three times more efficient" intercooler, a new exhaust, and a modified ECU were also included.[27] Weight was reduced significantly with the aid of further carbon fibre usage including lightweight vented bonnet and Recaro seats to reduce weight to 1,218kg (2,685lb) (from 1,250kg (2,756lb)) making this model road-going race car that matched the performance of the rival Porsche Carrera RS Club Sport for the final year Mazda officially entered.[26] The formula paid off when the RX-7 SP won the 1995 Eastern Creek 12 Hour, giving Mazda the winning 12-hour trophy for a fourth straight year.[26] The winning car also gained a podium finish at the international tarmac rally Targa Tasmania months later. A later special version, the Bathurst R, was introduced in 2001 to commemorate this victory in Japan only.[28] It was based on the RX-7 Type R and 500 were built in total, featuring adjustable dampers, a carbon fibre shift knob, carbon fibre interior trim, special fog lamps and a different parking brake lever.[29]
In Europe, only 1,152 examples of the FD were sold through the official Mazda network, due to a high price and a fairly short time span. Only one model was available and it included twin oil-coolers, electric sunroof, cruise control and the rear storage bins in place of the back seats.[30] It also has the stiffer suspension and strut braces from the R models.[31] Germany topped the sales with 446 cars, while UK is second at 210 and Greece third with 168 (thanks to that country's tax structure which favored the rotary engine).[32] The European models also received the 1994 interior facelift, with a passenger air bag.[citation needed] Sales in most of Europe ended after 1995 as it would have been too expensive to reengineer the car to meet the new Euro 2 emissions regulations.
United Kingdom
In the United Kingdom, for 1992, customers were offered only one version of the FD, which was based on a combination of the US touring and the base model.[30] For the following year, in a bid to speed up sales, Mazda reduced the price of the RX-7 to £25,000, down from £32,000, and refunded the difference to those who bought the car before that was announced. From 1992 to 1995, only 210 FD RX-7s were officially sold in the UK.[32] The FD continued to be imported to the UK until 1996. In 1998, for a car that had suffered from slow sales when it was officially sold, with a surge of interest and the benefit of a newly introduced SVA scheme, the FD would become so popular that there were more parallel and grey imported models brought into the country than Mazda UK had ever imported.[33]
Series 7 (1996–1998)
Series 7 included minor changes to the car. Updates included a simplified vacuum routing manifold and a 16-bit ECU which combined with an improved intake system netted an extra 10PS (7kW). This additional horsepower was only available on manual transmission cars as the increase in power was only seen above 7,000 rpm, which was the redline for automatic transmission equipped cars. The rear spoiler and tail lights were also redesigned. The Type RZ model was now equipped with larger brake rotors as well as 17-inch BBS wheels. In Japan, the Series 7 RX-7 was marketed under the Mazda and ɛ̃fini brand name.
Series 7 RX-7s were also sold in Australia, New Zealand and the UK. Series 7 models were produced only with right-hand drive (RHD), and were only exported to RHD markets.
Series 8 (1998–2002)
Series 8 was the final series, and was only available in the Japanese market. More efficient turbochargers were available on certain models, while improved intercooling and radiator cooling was made possible by a redesigned front fascia with larger openings. The seats, steering wheel, and instrument cluster were all changed. The rear spoiler was modified and gained adjustability on certain models. Three horsepower levels are available: 255PS (188kW; 252hp) for automatic transmission equipped cars, 265PS (195kW; 261hp)for the Type RB, and 280PS (206kW; 276hp) available on the top-of-the-line sporting models.
The high-end "Type RS" came equipped with Bilstein suspension and 17-inch wheels as standard equipment, and reduced weight to 1,280kg (2,822lb). Power was increased with the addition of a less restrictive muffler and more efficient turbochargers which featured abradable compressor seals, 280PS (206kW; 276hp) at 6,500 rpm and 314N⋅m (232lb⋅ft) of torque at 5000 rpm as per the maximum Japanese limit. The Type RS had a brake upgrade by increasing rotor diameter front and rear to 314mm (12.4in) and front rotor thickness from 22mm (0.9in) to 32mm (1.3in). The Type RS version also sported a 4.30 final drive ratio, providing a significant reduction in its 0–100km/h (62mph) time. The gearbox was also modified, 5th gear was made longer to reduce cruising rpm and improve fuel efficiency. The very limited edition Type RZ version included all the features of the Type RS, but at a lighter weight, at 1,270kg (2,800lb). It also featured gun-metal colored BBS wheels and a red racing themed interior. An improved ABS system worked by braking differently on each wheel, allowing the car better turning during braking. The effective result made for safer driving for the average buyer.
Mazda RX-7 Spirit RInstrument panel of RX-7 Spirit R
Easily the most collectible of all the RX-7s was the last model limited to 1,500 units. Dubbed the "Spirit R", they combined all the extra features Mazda had used on previous limited-run specials with new exclusive features like cross-drilled brake rotors. Sticker prices when new were 3,998,000 yen for Type-A and B and 3,398,000 yen for Type-C. Mazda's press release said "The Type-A Spirit R model is the ultimate RX-7, boasting the most outstanding driving performance in its history."
There are three models of "Spirit R": the "Type A", "Type B", and "Type C". The "Type A" is a two-seater with a five-speed manual transmission. It features lightweight red trim Recaro front seats as seen in the earlier RZ models. The "Type B" shares all features of the "Type A" but with a 2+2 seat configuration. The "Type C" is also a 2+2, but has a four-speed automatic transmission. Of the 1,504 Spirit R's made, 1,044 were Type A, 420 Type B and 40 Type C.[34] An exclusive Spirit R paint color, Titanium Grey, adorned 719 of the 1,504 cars produced.
In Japan the FD3S production span is categorized into six models: #1 from 1991/12, #2 from 1993/08, #3 from 1995/03, #4 from 1996/01, #5 from 1998/12 and #6 from 2000/10. The model number (1 to 6) shows as the first digit of the six-characters-long JDM VIN; e.g., in VIN FD3S-ABCDEF, the A is the model number. A total of nine limited editions (type RZ in 1992/10 (300 cars), RZ 1993/10 (150), R-II Bathurst 1994/09 (350), R Bathurst X 1995/07 (777), RB Bathurst X 1997/01 (700), RS-R 1997/10 (500), RZ 2000/10 (325), R Bathurst R 2001/08 (650), Spirit R 2002/04 (1504)) and 2 special editions (Bathurst R 1995/02, R Bathurst 2001/12 (2174)) were produced.[35][36][37]
In 2004, Sports Car International named the Series 3 car seventh on their list of Top Sports Cars of the 1970s. In 1983, the RX-7 would appear on Car and Driver magazine's Ten Best list for the first time in 20 years.
Though about 363kg (800lb) heavier and more insulated than its predecessor, the FC continued to win accolades from the press. The RX-7 FC was Motor Trend's Import Car of the Year for 1986, and the Turbo II was on Car and Driver magazine's 10Best list for a second time in 1987.
The FD RX-7 was Motor Trend'sImport Car of the Year for 1993. When Playboy first reviewed the FD RX-7 in 1993, they tested it in the same issue as the [then] new Dodge Viper. In that issue, Playboy declared the RX-7 to be the better of the two cars. It went on to win Playboy's Car of the Year for 1993.
The FD RX-7 also made Car and Driver's Ten Best list for 1993 through 1995 – all three years in which it was sold in the United States. In June 2007, Road & Track proclaimed: "The ace in Mazda's sleeve is the RX-7, a car once touted as the purest, most exhilarating sports car in the world." After its introduction in 1991, it won the Automotive Researchers' and Journalists' Conference Car of the Year award in Japan.
Handling in the FD RX-7 was regarded as world-class, and it is still regarded as being one of the finest-handling and best-balanced cars of all time.[38][39]
Racing versions of the first-generation RX-7 were entered at the prestigious 24 hours of Le Mans endurance race. The first outing for the car, equipped with a 13B engine, failed by less than one second to qualify in 1979. The next year, a 12A-equipped RX-7 not only qualified, it placed 21st overall. That same car did not finish in 1981, along with two more 13B cars. Those two cars were back for 1982, with one 14th-place finish and another DNF. The RX-7 Le Mans effort was replaced by the 717C prototype for 1983.
Mazda began racing RX-7s in the IMSAGTU series in 1979. In its first year, RX-7s placed first and second at the 24 Hours of Daytona, and claimed the GTU series championship. The car continued winning, claiming the GTU championship seven years in a row. The RX-7 took the GTO championship ten years in a row from 1982. In addition to this, a GTX version was developed, named the Mazda RX-7 GTP; this was unsuccessful, and the GTP version of the car was also unsuccessful. The RX-7 has won more IMSA races than any other car model. In the USA SCCA competition RX-7s were raced with great success by Don Kearney in the NE Division and John Finger in the SE Division. Pettit Racing won the GT2 Road Racing Championship in 1998. The car was a '93 Mazda RX-7 street car with only bolt-on accessories. At season end Pettit had 140 points—63 points more than the second place team. This same car finished the Daytona Rolex 24-hour race four times.
A Mazda RX-7 Group B rally car which competed in the 1979 Monte Carlo Rally
Canadian-born Australian touring car driver Allan Moffat was instrumental in bringing Mazda into the Australian touring car scene which ran to Group C regulations unique to Australia. Over a four-year span beginning in 1981, Moffat took the Mazda RX-7 to victory in the 1983 Australian Touring Car Championship, as well as a trio of Bathurst 1000 podiums, in 1981 (3rd with Derek Bell), 1983 (second with Yoshimi Katayama) and 1984 (third with former motorcycle champion Gregg Hansford). Privateer racer Peter McLeod drove his RX-7 to win the 1983 Australian Endurance Championship, while Moffat won the Endurance title in 1982 and 1984. Australia's adoption of international Group A regulations, combined with Mazda's reluctance to homologate a Group A RX-7 (meaning that a base number of 5,000 had to be built, plus another 500 "evolution" models), ended Mazda's active participation in Australian touring car racing at the end of the 1984 season. Plans had been in place to replace the RX-7 with a Mazda 929, but testing by Allan Moffat in late 1984 had indicated that the car would be uncompetitive and Mazda abandoned plans to race in Group A.
The RX-7 even made an appearance in the World Rally Championship. The car finished 11th on its debut at the RAC Rally in Wales in 1981. Group B received much of the focus for the first part of the 1980s, but Mazda did manage to place third at the 1985 Acropolis Rally, and when the Group B was folded, its Group A-based replacement, the 323 4WD claimed the victory at Swedish Rally in both 1987 and 1989.
IMSA Bridgestone Supercar Series
The third-generation Mazda RX-7 entered its first professional race in the world on February 23, 1992, at the Miami Grand Prix. The cars made it to the podium many times and won the IMSA Supercar race at Sebring in 1994. Peter Farrell Motorsport also fielded RX-7's in the IMSA Firestone Firehawk Endurance Series dominating many races and finishing runner up in the overall championship two years in a row.
Revivals
Mazda has made several references to a revival of the RX-7 in various forms over the years since the RX-8 was discontinued. In November 2012, MX-5 program manager Nobuhiro Yamamoto indicated that Mazda was working on a 16X based RX-7, with 300 horsepower.[40][41]
Mazda RX-Vision concept car
In October 2015, Mazda unveiled the RX-Vision concept car at the Tokyo Motor Show, powered by a new rotary engine and featured design cues reminiscent of the third generation RX-7. A production-ready concept could have followed suit by 2017, marking 50 years since the revealing of Mazda's first rotary-powered sports car, the Cosmo.[42]
Mazda Iconic SP concept car
In October 2023, Mazda unveiled the Iconic SP concept car at the Japan Mobility Show, powered by a two-rotor rotary engine and also features design cues reminiscent of the third generation RX-7, most notably its pop-up headlights.[43]
Related Research Articles
The Toyota Celica is an automobile produced by Toyota from 1970 until 2006. The Celica name derives from the Latin word coelica meaning heavenly or celestial. In Japan, the Celica was exclusive to Toyota Corolla Store dealer chain. Produced across seven generations, the Celica was powered by various four-cylinder engines, and body styles included convertibles, liftbacks, and notchback coupé.
The Mazda RX-8 is a sports car manufactured by Japanese automobile manufacturer Mazda between 2003 and 2012. It was first shown in 2001 at the North American International Auto Show. It is the direct successor to the RX-7. Like its predecessors in the RX range, it is powered by a rotary Wankel engine. The RX-8 was available for the 2003 model year in most parts of the world.
The Toyota Supra is a sports car and grand tourer manufactured by the Toyota Motor Corporation beginning in 1978. The name "supra" is derived from the Latin prefix, meaning "above", "to surpass" or "go beyond".
The Nissan 240SX is a sports compact car that was introduced to the North American market by Nissan in 1989 for the 1990 model year. It replaced the outgoing 200SX (S12) model. Most of the 240SXs were equipped with the 2.4-liter inline-four engine. The KA24E had a single overhead cam and the KA24DE had dual overhead cams. Two distinct generations of the 240SX, the S13 (1989–1994) the S14 (1994-1998) were produced, based on the Nissan S platform.
The Mazda Cosmo is an automobile which was produced by Mazda from 1967 until 1996. Throughout its history, the Cosmo served as a "halo" vehicle for Mazda, with the first Cosmo successfully launching the Mazda Wankel engine. The final generation of Cosmo served as Mazda's flagship vehicle in Japan, being sold as the Eunos Cosmo through its luxury Eunos division in Japan.
The Mazda Capella, also known as the 626 in Europe, North America and Southeast Asia, is a mid-size car that was manufactured by Mazda from 1970 until 2002. Sold in the Japanese domestic market under the Capella name, the vehicle was also commonly known in other major markets as the Mazda 626. Ford, Mazda's partner at the time, also used the Capella platform to create the Ford Telstar and Ford Probe. 4,345,279 of the 626 and Telstar models were sold worldwide.
The Mazda Luce is an executive car that was produced by Mazda in Japan from 1966 until 1991. It was widely exported as the Mazda 929 from 1973 to 1991 as Mazda's largest sedan. Later generations were installed with luxury items and interiors as the Luce became the flagship offering. The Luce was replaced by the Sentia in 1991 which was also exported under the 929 nameplate.
The Mazda Familia, also marketed prominently as the Mazda 323, Mazda Protegé and Mazda Allegro, is a small family car that was manufactured by Mazda between 1963 and 2003. The Familia line was replaced by the Mazda3/Axela for 2004.
The Nissan 300ZX is a sports car that was produced across two different generations. As with all other versions of the Z, the 300ZX was sold within the Japanese domestic market under the name Fairlady Z.
The Toyota Soarer is a personal luxury GT coupé produced from 1981 to 2005 by Toyota and sold in Japan. It was available at both Japanese Toyota dealerships called Toyota Store and Toyopet Store, and it debuted with the Z10 series, replacing the Toyopet Store exclusive Mark II coupé, the Toyota Auto Store exclusive Chaser coupé, and both the Toyota Store exclusive Crown coupé and Carina coupé.
The Mazda Wankel engines are a family of Wankel rotary combustion car engines produced by Mazda.
The Subaru Leone is a compact car produced by the Japanese car manufacturer Subaru from 1971 to 1994. The word leone is Italian for lion.
The Mazda 787 and its derivative 787B are Group C sports prototype racing cars that were developed by Japanese automobile manufacturer Mazda for use in the World Sportscar Championship, All Japan Sports Prototype Championship, and the 24 Hours of Le Mans from 1990 to 1991. Designed to combine a mixture of the Fédération Internationale du Sport Automobile (FISA) Group C regulations with the International Motor Sports Association (IMSA) GTP regulations, the 787s were the last Wankel rotary-powered racing cars to compete in the World and Japanese championships, using Mazda's R26B engine.
The Mazda B series is a series of pickup trucks that was manufactured by Mazda. Produced across five generations from 1961 to 2006, the model line began life primarily as a commercial vehicle, slotted above a kei truck in size. Through its production, Mazda used engine displacement to determine model designations; a B1500 was fitted with a 1.5 L engine and a B2600, a 2.6 L engine.
The Toyota Celica GT-Four is a high performance model of the Celica Liftback that was produced from 1986 to 1999, with a turbocharged 3S-GTE engine, and full-time AWD. It was created to compete in the World Rally Championship, whose regulations dictate that a manufacturer must build road-going versions of the vehicle in sufficient numbers. These vehicles are referred to as "homologation special vehicles".
The Mazda RX-01 was a concept car produced by Mazda that debuted at the 1995 Tokyo Motor Show.
The Mazda Grand Familia is an automobile which was produced by Mazda in Japan from 1971 to 1978. It was sold as the Mazda 808 in some export markets including Asia, Australia, and New Zealand, and as the Mazda 818 in many others - this was mostly due to Peugeot having trademarked three-digit numbers with a middle zero in many markets. The body style configurations offered were a two-door coupé, a four-door sedan, and a five-door station wagon. The Grand Familia offered only inline four cylinder engines. The largely identical rotary-powered versions were marketed as the Mazda Savanna in Japan, with export markets taking this model as the Mazda RX-3.
The Porsche 911 is a two-door 2+2 high performance rear-engined sports car introduced in September 1964 by Porsche AG of Stuttgart, Germany. It has a rear-mounted flat-six engine and originally a torsion bar suspension. The car has been continuously enhanced through the years but the basic concept has remained unchanged. The engines were air-cooled until the introduction of the 996 series in 1998.
Michael Brandon Whiddett also known as "Mad Mike", is a New Zealand drifting racer. He is sponsored by Red Bull. Whiddett has also raced motocross from the age of six and placed second at the New Zealand 1997 Pro junior 85cc Motocross Champs.
The Mazda MX-5 (NB) is the second generation of the Mazda MX-5 manufactured from 1998 until 2005. The model continued the MX-5's philosophy of being a lightweight, front mid-engine, rear-wheel-drive roadster while featuring numerous performance improvements, however lacking its predecessor's retractable headlamps. The NB is also the only generation to feature a factory-built turbocharged variant in the form of the Mazdaspeed MX-5.
↑ Lewis-George, Elliot (2013). Berg, Nik (ed.). "Mazda Heroes #1 – Ikuo Maeda". Zoom-Zoom Magazine (16): 6. Archived from the original on 2 February 2014. Retrieved 15 May 2013.
↑ Dieudonne, Pierre (1983-12-15). "Ballade Japonaise: à la découverte des Mazda Turbo" [Japanese ballad: Discovering the Mazda Turbos]. Le Moniteur de l'Automobile (in French). 34 (784): 40.
↑ O'Dell, John (30 January 1995). "Design Central". Los Angeles Times. a concept car whose design was inked at Mazda Research & Design in Irvine in 1989. It evolved into the curvy third-generation Mazda RX‑7 for the 1993 model year. The design was the work of 37-year old Wu-Huang Chin, above, who also was a member of the Miata design team.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
