A shower is a place in which a person bathes under a spray of typically warm or hot water. Indoors, there is a drain in the floor. Most showers are set up to have adjustable temperature, spray pressure and showerhead nozzle angle. The simplest showers have a swivelling nozzle aimed downward, while more complex showers have a showerhead connected to a hose that has a mounting bracket; this allows the showerer to hold the showerhead by hand to spray the water onto different parts of their body. A showerhead can be installed in a small shower stall, or bathtub, with a plastic shower curtain or door.
Showering is common due to the efficiency of using it compared with using a bathtub. Its use in hygiene is, therefore, common practice. [1] [ page needed ]
Waterfalls have historically been used as primitive forms of showers. [2] The falling water rinsed the bathers completely clean and was more efficient than bathing in a traditional basin, which required manual transport of both fresh and waste water. Ancient people began to reproduce these natural phenomena by pouring jugs of water, often very cold, over themselves after washing. There has been evidence of early upper class Egyptian and Mesopotamians having indoor shower rooms where servants would bathe them in the privacy of their own homes. [3] However, these were primitive by modern standards, having rudimentary drainage systems and water was carried, not pumped, into the room.
The ancient Greeks were the first people to have showers. Their aqueducts and sewage systems made of lead pipes allowed water to be pumped both into and out of large communal shower rooms used by elites and common citizens alike. [4] These rooms have been discovered at the site of the city Pergamum and can also be found represented in pottery of the era. The depictions are very similar to modern locker room showers, and even included bars to hang up clothing. [5] [ page needed ]
The ancient Romans also followed this convention; their famous bathhouses (Thermae) can be found all around the Mediterranean and as far out as modern-day England. The Romans not only had these showers but also believed in bathing several times a week, if not every day. The water and sewage systems developed by the Greeks and Romans broke down and fell out of use after the fall of the Roman Empire [ citation needed ].
The first known mechanical shower, operated by a hand pump, was patented in England in 1767 by William Feetham, a stove maker from Ludgate Hill in London.[ citation needed ] His shower contraption used a pump to force the water into a vessel above the user's head and a chain would then be pulled to release the water from the vessel. Although the system dispensed with the servant labour of filling up and pouring out buckets of water, the showers failed to catch on with the rich as a method for piping hot water through the system was not available. The system would also recycle the same dirty water through every cycle.
This early start was greatly improved in the anonymously invented English Regency shower design of c. 1810 (there is some ambiguity among the sources). [2] The original design was over 10 ft (3.0 m) tall, and was made of several metal pipes painted to look like bamboo. A basin suspended above the pipes fed water into a nozzle that distributed the water over the user's shoulders. The water on the ground was drained and pumped back through the pipes into the basin, where the cycle would repeat itself.[ citation needed ] The prototype was steadily improved upon in the following decades until it began to approximate the shower of today in its mode of operation. Hand-pumped models became fashionable at one point as well as the use of adjustable sprayers for different water flow. The reinvention of reliable indoor plumbing around 1850 allowed free-standing showers to be connected to a running water source, supplying a renewable flow of water. [7] The shower cabin was invented in 1839 by Polish-Canadian politician and engineer Aleksander Edward Kierzkowski. [8]
Modern showers were installed in the barracks of the French army in the 1870s as an economic hygiene measure, under the guidance of François Merry Delabost, a French doctor and inventor. [9] As surgeon-general at Bonne Nouvelle prison in Rouen, Delabost had previously replaced individual baths with mandatory communal showers for use by prisoners, arguing that they were more economical and hygienic. [10] First six, then eight shower stalls were installed. The water was heated by a steam engine and in less than five minutes, up to eight prisoners could wash simultaneously with only twenty litres of water. The French system of communal showers was adopted by other armies, the first being that of Prussia in 1879, and by prisons in other jurisdictions. They were also adopted by boarding schools, before being installed in public bathhouses. The first shower in a public bathhouse was in 1887 in Vienna. In France, public bathhouses and showers were established by Charles Cazalet, firstly in Bordeaux in 1893 and then in Paris in 1899. [11]
Domestic showers are most commonly stall showers or showers combined with a bathtub. A stall shower is a dedicated shower area which uses a door or curtain to contain water spray. The shower/tub format saves bathroom space and enables the area to be used for either a bath or a shower and commonly uses a sliding shower curtain or door to contain the water spray. Showers may also be in a wet room, in which there is no contained shower area, or in a dedicated shower room, which does not require containment of water spray. Domestic showers can have a single shower head, multiple shower heads, handheld shower head(s) or other variations, all which may be adjustable as needed to varying degrees.
Many modern athletic and aquatic facilities provide showers for use by patrons, commonly in gender segregated changing rooms. These can be in the form of individual stalls shielded by curtains or a door or communal shower rooms. The latter are generally large open rooms with any number of shower heads installed either directly into the walls or on posts throughout the shower area. Open showers are often provided at public swimming pools and at popular beaches. Military forces around the world set up field showers to enable the washing away of dangerous residue from modern weapons such as caustic chemicals, deadly biological agents, and radioactive materials, which can harm forces on both sides of a conflict. [12]
A wet room often refers to a bathroom without internal dedicated or raised areas which has an open shower. Structurally, a wet room requires the bathroom to have a gradient or slope towards a drain hole, and a foul air trap connecting the floor to the waste pipes. Depending on region, the term wet room can also encompass other rooms such as laundry rooms. In Norway, for example, any room with tap water and a drain in the floor is considered a wet room. [13] Different jurisdictions often have special regulations concerning the design and construction of wet rooms to prevent damage from damp air or water leakage, e.g. mold.
There are also often special regulations concerning electrical installations in wet rooms. For example, since water supplies often have their own electrical grounding, there can be an added risk of injury associated with ground faults, and some jurisdictions therefore require the installation of residual-current devices in wet rooms.
Shower usage in the latter half of the 20th century skyrocketed. Personal hygiene became a primary concern, and bathing every day or multiple times a day is common among Western cultures. [1] [ page needed ] Showering is generally faster than bathing and can use less water. In an average home, showers are typically the third largest water use after toilets and clothes washers. The average American shower uses 17.2 US gallons (65 L; 14.3 imp gal) and lasts for 8.2 minutes at an average flow rate of 2.1 US gallons (7.9 L; 1.7 imp gal) per minute. [19]
Showering is one of the leading ways people use water in the home, accounting for nearly 17 percent of residential indoor water use, which roughly equals to 1,200,000,000 US gallons (4.5×109 L; 1.00×109 imp gal) of water annually just for showering. [20] The US Environmental Protection Agency recommends to retrofit home showers with a shower head that uses less than 2 US gallons (7.6 L; 1.7 imp gal) to conserve water. However, many have hypothesized reducing flow rates of showerheads might cause users to take much longer showers. [21] Other options to save water include using extra high pressure mist flow or design in sensors and valves to shut off or reduce water flow while people are not actively using the shower water.
Various measures can be taken to increase safety for those, especially elderly people, taking showers or baths. [22] Some people take more than one shower each day, normally at their normal shower time, and after exercising. People also shower to cool off in hot weather, especially those unaccustomed to the climate. [23] [ better source needed ] Used shower water can be employed as greywater.
Showering is mostly part of a daily routine primarily to promote cleanliness and prevent odor, disease and infection. Advances in science and medicine in the 19th century began to realize the benefit of regular bathing to an individual's health. As a result, most modern cultures encourage a daily personal hygiene regimen. Showering has also developed the reputation as a relaxing and generally therapeutic activity. [1] [ page needed ]
Designs for shower facilities vary by location and purpose. There are free-standing showers, but also showers which are integrated into a bathtub. Showers are separated from the surrounding area through watertight curtains (shower curtain), sliding doors, or folding doors, or shower blinds, in order to protect the space from spraying water. Showers with a level entry wet room are becoming very popular, especially due to improvements in waterproofing systems and prefabricated components.
Places such as a swimming pool, a locker room, or a military facility have multiple showers. There may be communal shower rooms without divisions, or shower stalls (typically open at the top). Many types of showers are available, including complete shower units which are all encompassing showers that include the pan, walls, and often the shower head, as well as pieced together units in which the pan, shower head, and doors are purchased separately. Each type of shower poses different installation issues.
Though the installation requirements of each of shower will differ, the installation of a shower in general requires the laying of several water transportation pipes, including a pipe for hot water and for cold water, and a drainage pipe. It is important that the wet areas of a bathroom be waterproof, and multiple layers of waterproofing can be employed. Grout is used to fill gaps between tiles, but grout and tile setting materials are generally porous. Tiles are generally waterproof, though a shower pan must be installed beneath them as a safety to prevent water leakage. [24] Thus small mosaic tiles offer less of a defense than large format tiles. Sub-tile waterproofing is important when tiles are being used. Best practice requires a waterproofing material to cover the walls and floor of the shower area that are then covered with tile, or in some countries with a sheet material like vinyl.
A shower may be equipped with a second emergency drain outside of the shower in case of overflow. An emergency overflow drain is required in Australia and some European countries.[ citation needed ]
A shower head is a perforated nozzle that distributes water over solid angle a focal point of use, generally overhead the bather. A shower uses less water than a full immersion in a bath. Some shower heads can be adjusted to spray different patterns of water, such as massage, gentle spray, strong spray, and intermittent pulse or combination modes.
Hard water may result in calcium and magnesium deposits clogging the head, reducing the flow and changing the spray pattern. For descaling, various acidic chemicals or brushes can be used or some heads have rubber-like jets that can be manually descaled. A homemade remedy is to immerse it in a solution of water and vinegar for a while, since the vinegar is able to dissolve limescale.
Some governments around the world set standards for water usage and regulate shower heads. For example, in the United States, residential and most commercial shower heads must flow no more than 9.5 litres (2.1 imp gal; 2.5 US gal) per minute per the Department of Energy ruling 10 CFR 430. Low-flow shower heads that have a water flow of equal or less than 7.6 litres (1.7 imp gal; 2.0 US gal) per minute (2.0 gallons per minute), can use water more efficiently by aerating the water stream, altering nozzles through advanced flow principles or by high-speed oscillation of the spray stream. The US EPA administers a voluntary water saving program, WaterSense, which can certify low-flow shower heads.
Curtains can be used in shower or bathtub enclosures with two main purposes: to provide privacy and to prevent water from flooding or spraying outside the shower or bathtub area. Shower and bathtub curtains usually surround the bath inside the tub or shower area and are held up with railings or curtain rods high on the wall or ceiling. To accommodate the different types of bathtub shapes, railings can come in different sizes and are flexible in their design. The curtains are usually made from vinyl, cloth, or plastic.
Some people use two shower curtains: one that is inside the tub, which is mainly functional or decorative as well, and an outer shower curtain, which is purely decorative. The bottom portion of the inner curtain often comes with magnetic discs or suction cups which adhere to the bathtub itself.
Shower or bathtub doors are doors (also called screens) used in bathrooms that help keep water inside a shower or bathtub and are alternatives to shower curtains. They are available in many different styles such as framed or frameless, sliding or swing. They are usually constructed of aluminium, clear glass, plexiglass or tempered glass. Shower doors can come in many different hardware finishes and glass patterns that can match other bathroom hardware such as faucets and shower heads. There are also shower doors that are in a neo angle design for use on shower pans that have the neo design as well. The design of the shower pan is extremely important as the shower door must be the type required for the pan in order to work. A shower door requires plastic lining along the edges of the door to protect against water leaking out.
by 1845, the installation of sanitary sewers began to pay off ... In 1874, ... an unknown plumber solved the problem of venting.
A bathroom is a room in which people wash their bodies or parts thereof. It can contain one or more of the following plumbing fixtures: a shower, a bathtub, a bidet, and a sink. The inclusion of a toilet is common. There are also specific toilet rooms, only containing a toilet, which in North American English tend to be called "bathrooms", "powder rooms" or "washrooms", as euphemisms to conceal their actual purpose, while they in British and Irish English are known as just "toilets" or possibly "cloakrooms" - but also as "lavatories" when they are public.
A flush toilet is a toilet that disposes of human waste by collecting it in a bowl and then using the force of water to channel it through a drainpipe to another location for treatment, either nearby or at a communal facility. Flush toilets can be designed for sitting or squatting. Most modern sewage treatment systems are also designed to process specially designed toilet paper, and there is increasing interest for flushable wet wipes. Porcelain is a popular material for these toilets, although public or institutional ones may be metal, etc.
Sentō (銭湯) is a type of Japanese communal bathhouse where customers pay for entrance. Traditionally these bathhouses have been quite utilitarian, with a tall barrier separating the sexes within one large room, a minimum of lined-up faucets on both sides, and a single large bath for the already washed bathers to sit in among others. Since the second half of the 20th century, these communal bathhouses have been decreasing in numbers as more and more Japanese residences now have baths. Some Japanese find social importance in going to public baths, out of the theory that physical proximity/intimacy brings emotional intimacy, which is termed skinship in pseudo-English Japanese. Others go to a sentō because they live in a small housing facility without a private bath or to enjoy bathing in a spacious room and to relax in saunas or jet baths that often accompany new or renovated sentōs.
A bidet is a bowl or receptacle designed to be sat upon in order to wash a person's genitalia, perineum, inner buttocks, and anus. The modern variety has a plumbed-in water supply and a drainage opening, and is thus a plumbing fixture subject to local hygiene regulations. The bidet is designed to promote personal hygiene and is used after defecation, and before and after sexual intercourse. It can also be used to wash feet, with or without filling it up with water. Some people even use bidets to bathe babies or pets. In several European countries, a bidet is now required by law to be present in every bathroom containing a toilet bowl. It was originally located in the bedroom, near the chamber-pot and the marital bed, but in modern times is located near the toilet bowl in the bathroom. Fixtures that combine a toilet seat with a washing facility include the electronic bidet.
The shower-curtain effect in physics describes the phenomenon of a shower curtain being blown inward when a shower is running. The problem of identifying the cause of this effect has been featured in Scientific American magazine, with several theories given to explain the phenomenon but no definite conclusion.
A tap is a valve controlling the release of a fluid.
Water heating is a heat transfer process that uses an energy source to heat water above its initial temperature. Typical domestic uses of hot water include cooking, cleaning, bathing, and space heating. In industry, hot water and water heated to steam have many uses.
A basement or cellar is one or more floors of a building that are completely or partly below the ground floor. Especially in residential buildings, it often is used as a utility space for a building, where such items as the furnace, water heater, breaker panel or fuse box, car park, and air-conditioning system are located; so also are amenities such as the electrical system and cable television distribution point. In cities with high property prices, such as London, basements are often fitted out to a high standard and used as living space.
A bathtub, also known simply as a bath or tub, is a container for holding water in which a person or another animal may bathe. Most modern bathtubs are made of thermoformed acrylic, porcelain-enameled steel or cast iron, or fiberglass-reinforced polyester. A bathtub is placed in a bathroom, either as a stand-alone fixture or in conjunction with a shower.
A curtain rod, curtain rail, curtain pole, or traverse rod is a device used to suspend curtains, usually above windows or along the edges of showers or bathtubs, though also wherever curtains might be used. When found in bathrooms, curtain rods tend to be telescopic and self-fixing, while curtain rods in other areas of the home are often affixed with decorative brackets or finial. Special poles can be made for bay windows or made by joining a number of straight and corner bends to fit the shape of a bay window.
Anal hygiene refers to practices that are performed on the anus to maintain personal hygiene, usually immediately or shortly after defecation. Anal cleansing may also occur while showering or bathing. Post-defecation cleansing is rarely discussed academically, partly due to the social taboo surrounding it. The scientific objective of post-defecation cleansing is to prevent exposure to pathogens.
WaterSense is a program sponsored by the U.S. Environmental Protection Agency (EPA), designed to encourage water efficiency in the United States through the use of a special label on consumer products. The goal of this program is to protect the future of the U.S. water supply. WaterSense maintains partnerships with key utility, manufacturer and retail partners across the United States. WaterSense is voluntary, rather than a regulatory program. The EPA develops specifications for water-efficient products – low-flow fixtures – through a public process. If a manufacturer makes a product that meets those specifications, the product is eligible for third-party testing to ensure the stated efficiency and performance criteria have been met. If the product passes the test, the manufacturer is rewarded with the right to put the WaterSense label on that product.
Builders' hardware or just builders hardware is a group of metal hardware specifically used for protection, decoration, and convenience in buildings. Building products do not make any part of a building, rather they support them and make them work. It usually supports fixtures like windows, doors, and cabinets. Common examples include door handles, door hinges, deadbolts, latches, numerals, letter plates, switch plates, and door knockers.
Accessible bathtubs are bathtubs that can be used by people with limited mobility, disabilities, and the elderly. A bathtub can be made accessible for some people by the addition of grab bars or hand grips, or through the use of lifts that lower and raise the bather in the water. Other bathtubs have been specially designed for accessibility. These may include walk-in bathtubs, tubs with built-in transfer benches, or, more recently, tubs with raised beds and sliding doors to allow for a seated transfer.
A shower splash guard is a permanently installed, fixed, rigid fitting made of plastic or glass that prevent water from a shower from splashing out of the bathtub and onto the floor. Typically, the shower splash guard is a small triangular piece of plastic that is used in combination with a shower curtain, to prevent water escaping at the corners, but it may be a much larger piece that is used by itself.
Canada's Worst Handyman 6 was the sixth and final season of Canada's Worst Handyman, a Canadian reality television series on Discovery Channel which seeks to improve the do-it-yourselfer skills of five contestants. In this season, the contestants must transform several rooms in the Niagara Falls Carriage House on Lundy's Lane in Niagara Falls, Ontario and transform the space into a retreat for newlyweds. Group challenges this year will be focused on transforming a common area into a spa. As with its sister season Canada's Worst Driver 6, a new series logo was commissioned for this season, dubbed "the honeymoon suite season" for all but the first episode.
A toilet is a small room used for privately accessing the sanitation fixture (toilet) for urination and defecation. Toilet rooms often include a sink (basin) with soap/handwash for handwashing, as this is important for personal hygiene. These rooms are typically referred to in North America as half-bathrooms in a private residence.
Tankless water heaters — also called instantaneous, continuous flow, inline, flash, on-demand, or instant-on water heaters — are water heaters that instantly heat water as it flows through the device, and do not retain any water internally except for what is in the heat exchanger coil unless the unit is equipped with an internal buffer tank. Copper heat exchangers are preferred in these units because of their high thermal conductivity and ease of fabrication. However, copper heat exchangers are more susceptible to scale buildup than stainless steel heat exchangers.
Residential water use includes all indoor and outdoor uses of drinking quality water at single-family and multifamily dwellings. These uses include a number of defined purposes such as flushing toilets, washing clothes and dishes, showering and bathing, drinking, food preparation, watering lawns and gardens, and maintaining swimming pools. Some of these end uses are detectable while others are more difficult to gauge.
A low-flow fixture is a water saving plumbing fixture designed to achieve water savings by having a lower flow rate of water or a smaller quantity per flush. Some of these low-flow fixtures are faucets, showerheads, and toilets. In the United States a maximum water usage of conventional plumbing fixtures was federally mandated by the Energy policy act of 1992. Low-flow fixtures are designed to save water over conventional fixtures by having a lower flow rate while still maintaining satisfactory performance. The Environmental protection agency (EPA) WaterSense program has requirements for plumbing fixtures to achieve their definition for water saving low-flow.