Lapp knot | |
---|---|
Names | Lapp knot, Lap knot, Lap bend, Lapp bend |
Category | Bend |
Category 2 | Loop |
Origin | Ancient |
Related | sheet bend, bowline, cowboy bowline, Eskimo bowline |
Releasing | Non-jamming |
Typical use | Joining two lines, loop, binding knot |
ABoK | #1224 |
The Lapp knot is a type of bend. It has the same structure as the sheet bend, but the opposite ends are loaded. The slipped Lapp bend is also an exploding knot, which means that when pulling the quick release end it falls completely apart without further entanglement. It is as strong as or even stronger than the sheet bend, [1] though much less common.
The Lapp knot is closely related to the sheet bend, the bowline and the Eskimo bowline. They all share the same core structure, but differ in how the four ends are loaded. The Lapp knot was sometimes called 'false sheet bend', [2] which might explain its low popularity.
A way to tie the knot is shown in the image to the left. The orientation of the green bight is important: Its working end should end up on the same side as the red lines slip bight, or as the red working end when tying the non-slip version (A & C). If they end up on opposite sides (B & C), the resulting knot is much weaker and tends to slip, because then the two standing parts lose some of their binding force due to mutual friction before they can clamp down the loose ends.[ clarification needed ] (The same is true for the bowline.)
The non-slipped Lapp bend (like the bowline) does not jam and can be untied easily even after being loaded. The slipped version unties even easier with a firm tug on the end E (quick release).
The Lapp knot can be tied as a loop knot, in which case A becomes the standing part in the loop, B and D the two strands of the loop, and C the free end. It is also a secure loop if B is the standing part rather than A, though this variation is insecure under ring loading as it mimics the weaker version of the Lapp bend.
The knot loses some of its adjustability after the standing part has been loaded. If the knot isn't tightened properly before loading, or A and B are pulled apart, it might capsize into a Mooring hitch. The knot can also be tied by first tying a Mooring hitch, then adjusting it to the desired size, then pulling the slipped end away from the loop.
If D is the standing part, rather than A, the result is commonly known as the Eskimo bowline.
The slipped Lapp knot can also be used as a binding knot for bundles or rolls (or a bathrobe). Its advantage over the reef knot is that the finished knot can be tightened by pulling the slip loop and end (C+E) and the working end A in opposite directions, or loosened by pulling B instead of A. When releasing C+E, it pulls tight again. Pulling only end E dissolves it completely.
The knot is documented since 1892 under various names (false weaver's bend, false sheet bend, English Bowline, Girdle Knot), and was used by various native cultures (America, Lapland, Africa, Australia). [3] The name Lap(p) knot stems from it having been used in Lapland to tie reindeer to a sled and for lanyards. The slipped Lapp knot is also shown in The Ashley Book of Knots as #1224, a nameless decorative bathrobe cord knot.
As a bend:
As a loop:
As a binding knot:
A knot is an intentional complication in cordage which may be practical or decorative, or both. Practical knots are classified by function, including hitches, bends, loop knots, and splices: a hitch fastens a rope to another object; a bend fastens two ends of a rope to each another; a loop knot is any knot creating a loop; and splice denotes any multi-strand knot, including bends and loops. A knot may also refer, in the strictest sense, to a stopper or knob at the end of a rope to keep that end from slipping through a grommet or eye. Knots have excited interest since ancient times for their practical uses, as well as their topological intricacy, studied in the area of mathematics known as knot theory.
The bowline is an ancient and simple knot used to form a fixed loop at the end of a rope. It has the virtues of being both easy to tie and untie; most notably, it is easy to untie after being subjected to a load. The bowline is sometimes referred to as king of the knots because of its importance. Along with the sheet bend and the clove hitch, the bowline is often considered one of the most essential knots.
The constrictor knot is one of the most effective binding knots. Simple and secure, it is a harsh knot that can be difficult or impossible to untie once tightened. It is made similarly to a clove hitch but with one end passed under the other, forming an overhand knot under a riding turn. The double constrictor knot is an even more robust variation that features two riding turns.
A shank is a type of knot that is used to shorten a rope or take up slack, such as the sheepshank. The sheepshank knot is not stable. It will fall apart under too much load or too little load.
The clove hitch is an ancient type of knot, made of two successive single hitches tied around an object. It is most effectively used to secure a middle section of rope to an object it crosses over, such as a line on a fencepost. It can also be used as an ordinary hitch, or as a binding knot, but it is not particularly secure in either application. It is considered one of the most important knots, alongside the bowline and the sheet bend.
Although the name clove hitch is given by Falconer in his Dictionary of 1769, the knot is much older, having been tied in ratlines at least as early as the first quarter of the sixteenth century. This is shown in early sculpture and paintings. A round turn is taken with the ratline and then a hitch is added below. The forward end is always the first to be made fast.
The trucker's hitch is a compound knot commonly used for securing loads on trucks or trailers. The general arrangement, using loops and turns in the rope itself to form a crude block and tackle, has long been used to tension lines and is known by multiple names. Knot author Geoffrey Budworth claims the knot can be traced back to the days when carters and hawkers used horse-drawn conveyances to move their wares from place to place.
The Eskimo bowline, Cossack knot, reverse bowline, or 'anti-bowline' is in a class of knots known as 'eye knots' or 'loop knots'. The eye is formed in the end of the rope to permit attachments/connections. It is quite common in Russia and is often used instead of the bowline. In the simple bowline, the collar component forms around the 'standing part'. In contrast, the collar component of an Eskimo bowline forms around the outgoing eye-leg.
The marlinespike hitch is a temporary knot used to attach a rod to a rope in order to form a handle. This allows more tension than could be produced comfortably by gripping the rope with the hands alone. It is useful when tightening knots and for other purposes in ropework.
The taut-line hitch is an adjustable loop knot for use on lines under tension. It is useful when the length of a line will need to be periodically adjusted in order to maintain tension. It is made by tying a rolling hitch around the standing part after passing around an anchor object. Tension is maintained by sliding the hitch to adjust the size of the loop, thus changing the effective length of the standing part without retying the knot.
A zeppelin bend is an end-to-end joining knot formed by two symmetrically interlinked overhand knots. It is stable, secure, and highly resistant to jamming. It is also resistant to the effects of slack shaking and cyclic loading.
The buntline hitch is a knot used for attaching a rope to an object. It is formed by passing the working end around an object, then making a clove hitch around the rope's standing part and taking care that the turns of the clove hitch progress towards the object rather than away from it. Secure and easily tied, the buntline hitch will jam when subjected to extreme loads. Given the knot's propensity to jam, it is often made in slipped form.
The buntline hitch, when bent to a yard, makes a more secure knot than two half hitches, but is more liable to jam. It differs from two half hitches in that the second half hitch is inside instead of outside the first one.
The adjustable grip hitch is a simple and useful friction hitch which may easily be shifted up and down the rope while slack. It will hold fast when loaded, but slip when shock loaded until tension is relieved enough for it to again hold fast. It serves the same purpose as the taut-line hitch, e.g. tensioning a tent's guy line.
The cowboy bowline or left-hand bowline, is a variation of the bowline loop knot.
A Prusik is a friction hitch or knot used to attach a loop of cord around a rope, applied in climbing, canyoneering, mountaineering, caving, rope rescue, ziplining, and by arborists. The term Prusik is a name for both the loops of cord used to tie the hitch and the hitch itself, and the verb is "to prusik". More casually, the term is used for any friction hitch or device that can grab a rope. Due to the pronunciation, the word is often misspelled Prussik, Prussick, or Prussic.
Two half-hitches is a type of knot, specifically a binding knot or hitch knot. One variety consists of an overhand knot tied around a post, followed by a half-hitch. This knot is less often referred to as a clove hitch over itself, double half-hitch, or full-hitch.
Two half hitches is the commonest of all hitches for mooring in particular and also for general utility. Steel gives the name in 1794. The difference between two half hitches and the clove hitch is that the former, after a single turn around a spar, is made fast around its own standing part, while the latter is tied directly around the spar.
In knot tying, a bight is a curved section or slack part between the two ends of a rope, string, or yarn. A knot that can be tied using only the bight of a rope, without access to the ends, is described as in the bight. The term "bight" is also used in a more specific way when describing Turk's head knots, indicating how many repetitions of braiding are made in the circuit of a given knot.
The Farrimond friction hitch is a quick release adjustable friction hitch for use on lines under tension. It is useful when the length of a line will need to be periodically adjusted in order to maintain or adjust tension whilst remaining quick and easy to untie; such as when hanging the ridge line for a Basha. It can be used in very effective conjunction with the Siberian hitch for this purpose. It can also be used as a mooring knot.
The harness knot is a general purpose bend knot used to join two ropes together. The knot can be tied under tension and will not capsize.