Development of modern stealth technologies in the United States began in 1958,[3][4] where earlier attempts to prevent radar tracking of its U-2 spy planes during the Cold War by the Soviet Union had been unsuccessful.[5] Designers turned to developing a specific shape for planes that tended to reduce detection by redirecting electromagnetic radiation waves from radars.[6]Radiation-absorbent material was also tested and made to reduce or block radar signals that reflect off the surfaces of aircraft. Such changes to shape and surface composition comprise stealth technology as currently used on the Northrop Grumman B-2 Spirit "Stealth Bomber".[4]
The concept of stealth is to operate or hide while giving enemy forces no indication as to the presence of friendly forces. This concept was first explored through camouflage to make an object's appearance blend into the visual background. As the potency of detection and interception technologies (radar, infrared search and tracking, surface-to-air missiles, etc.) have increased, so too has the extent to which the design and operation of military personnel and vehicles have been affected in response. Some military uniforms are treated with chemicals to reduce their infrared signature. A modern stealth vehicle is designed from the outset to have a chosen spectral signature. The degree of stealth embodied in a given design is chosen according to the projected threats of detection.
History
Camouflage to aid or avoid predation predates humanity, and hunters have been using vegetation to conceal themselves, perhaps as long as people have been hunting. The earliest application of camouflage in warfare is impossible to ascertain. Methods for visual concealment in war were documented by Sun Tzu in his book The Art of War in the 5th century BC, and by Frontinus in his work Strategemata in the 1st century AD.[7]
In England, irregular units of gamekeepers in the 17th century were the first to adopt drab colours (common in 16th century Irish units) as a form of camouflage, following examples from the continent.
During World War I, the Germans experimented with the use of Cellon (Cellulose acetate), a transparent covering material, in an attempt to reduce the visibility of military aircraft. Single examples of the Fokker E.IIIEindecker fighter monoplane, the Albatros C.I two-seat observation biplane, and the Linke-Hofmann R.I prototype heavy bomber were covered with Cellon. However, sunlight glinting from the material made the aircraft even more visible. Cellon was also found to degrade quickly from both sunlight and in-flight temperature changes, so the effort to make transparent aircraft ceased.[8]
In 1916, the British modified a small SS class airship for the purpose of night-time reconnaissance over German lines on the Western Front. Fitted with a silenced engine and a black gas bag, the craft was both invisible and inaudible from the ground but several night-time flights over German-held territory produced little useful intelligence and the idea was dropped.[9]
Chaff was invented in Britain and Germany early in World War II as a means to hide aircraft from radar. In effect, chaff acted upon radio waves much as a smoke screen acted upon visible light.[11]
The U-boat U-480 may have been the first stealth submarine. It featured an anechoic tile rubber coating, one layer of which contained circular air pockets to defeat ASDIC sonar.[12] Radar-absorbent paints and materials of rubber and semiconductor composites (codenames: Sumpf, Schornsteinfeger) were used by the Kriegsmarine on submarines in World War II. Tests showed they were effective in reducing radar signatures at both short (centimetres) and long (1.5 metre) wavelengths.[13]
In 1956, the CIA began attempts to reduce the radar cross-section (RCS) of the U-2 spyplane. Three systems were developed, Trapeze, a series of wires and ferrite beads around the planform of the aircraft, a covering material with PCB circuitry embedded in it, and radar-absorbent paint. These were deployed in the field on the so-called dirty birds but results were disappointing, the weight and drag increases were not worth any reduction in detection rates. More successful was applying camouflage paint to the originally bare metal aircraft; a deep blue was found to be most effective. The weight of this cost 250ft in maximum altitude, but made the aircraft harder for interceptors to see.[14]
In 1958, the U.S. Central Intelligence Agency requested funding for a reconnaissance aircraft to replace the existing U-2 spy planes,[15] and Lockheed secured contractual rights to produce it.[3]"Kelly" Johnson and his team at Lockheed's Skunk Works were assigned to produce the A-12 (or OXCART), which operated at high altitude of 70,000 to 80,000ft (21,000 to 24,000m) and speed of Mach3.2 (2,400mph; 3,800km/h) to avoid radar detection. Various plane shapes designed to reduce radar detection were developed in earlier prototypes, named A-1 to A-11. The A-12 included a number of stealthy features including special fuel to reduce the signature of the exhaust plume, canted vertical stabilizers, the use of composite materials in key locations, and the overall finish in radar-absorbent paint.[14]
In 1960, the USAF reduced the radar cross-section of a Ryan Q-2C Firebee drone. This was achieved through specially designed screens over the air intake, and radiation-absorbent material on the fuselage, and radar-absorbent paint.[16]
The United States Army issued a specification in 1968 which called for an observation aircraft that would be acoustically undetectable from the ground when flying at an altitude of 1,500ft (460m) at night. This resulted in the Lockheed YO-3A Quiet Star, which operated in South Vietnam from late June 1970 to September 1971.[17]
During the 1970s, the U.S. Department of Defense launched project Lockheed Have Blue, with the aim of developing a stealth fighter. There was fierce bidding between Lockheed and Northrop to secure the multibillion-dollar contract. Lockheed incorporated into its bid a text written by the Soviet-Russian physicist Pyotr Ufimtsev from 1962, titled Method of Edge Waves in the Physical Theory of Diffraction, Soviet Radio, Moscow, 1962. In 1971, this book was translated into English with the same title by the U.S. Air Force, Foreign Technology Division.[18] The theory played a critical role in the design of American stealth-aircraft F-117 and B-2.[19][20][21] Equations outlined in the paper quantified how a plane's shape would affect its detectability by radar, termed radar cross-section (RCS).[22] At the time, the Soviet Union did not have supercomputer capacity to solve these equations for actual designs. This was applied by Lockheed in computer simulation to design a novel shape they called the "Hopeless Diamond", a wordplay on the Hope Diamond, securing contractual rights to produce the F-117 Nighthawk starting in 1975. In 1977, Lockheed produced two 60% scale models under the Have Blue contract. The Have Blue program was a stealth technology demonstrator that lasted from 1976 to 1979. The Northrop Grumman Tacit Blue also played a part in the development of composite material and curvilinear surfaces, low observables, fly-by-wire, and other stealth technology innovations. The success of Have Blue led the Air Force to create the Senior Trend program which developed the F-117.[23][24]
In the early 21st century, the proliferation of stealth technology began outside of the United States. Both Russia and China tested their stealth aircraft in 2010. Russia manufactured 10 flyable prototypes of the Su-57, while China produced two stealth aircraft, Chengdu J-20 and Shenyang FC-31.[25] In 2017, China became the second country in the world to field an operational stealth aircraft, challenging the United States and its Asian allies.[26][27]
Principles
Stealth technology (or LO for low observability) is not one technology. It is a set of technologies, used in combinations, that can greatly reduce the distances at which a person or vehicle can be detected; more so radar cross-section reductions, but also acoustic, thermal, and other aspects.
Almost since the invention of radar, various methods have been tried to minimize detection. Rapid development of radar during World War II led to equally rapid development of numerous counter radar measures during the period; a notable example of this was the use of chaff. Modern methods include radar jamming and deception.
The term stealth in reference to reduced radar signature aircraft became popular during the late eighties when the Lockheed Martin F-117 stealth fighter became widely known. The first large scale (and public) use of the F-117 was during the Gulf War in 1991. However, F-117A stealth fighters were used for the first time in combat during Operation Just Cause, the United States invasion of Panama in 1989.[28] Stealth aircraft are often designed to have radar cross sections that are orders of magnitude smaller than conventional aircraft. The radar range equation meant that all else being equal, detection range is proportional to the fourth root of RCS; thus, reducing detection range by a factor of 10 requires a reduction of RCS by a factor of 10,000.
The F-35 Lightning II offers better stealthy features (such as this landing gear door) than prior American multi-role fighters, such as the F-16 Fighting Falcon
The possibility of designing aircraft in such a manner as to reduce their radar cross-section was recognized in the late 1930s, when the first radar tracking systems were employed, and it has been known since at least the 1960s that aircraft shape makes a significant difference in detectability. The Avro Vulcan, a British bomber of the 1960s, had a remarkably small appearance on radar despite its large size, and occasionally disappeared from radar screens entirely. It is now known that it had a fortuitously stealthy shape apart from the vertical element of the tail. Despite being designed before a low radar cross-section (RCS) and other stealth factors were ever a consideration,[29] a Royal Aircraft Establishment technical note of 1957 stated that of all the aircraft so far studied, the Vulcan appeared by far the simplest radar echoing object, due to its shape: only one or two components contributing significantly to the echo at any aspect (one of them being the vertical stabilizer, which is especially relevant for side aspect RCS), compared with three or more on most other types.[30][32] While writing about radar systems, authors Simon Kingsley and Shaun Quegan singled out the Vulcan's shape as acting to reduce the RCS.[33] In contrast, the Tupolev 95 Russian long-range bomber (NATO reporting name 'Bear') was conspicuous on radar. It is now known that propellers and jet turbine blades produce a bright radar image;[citation needed] the Bear has four pairs of large 18-foot (5.6m) diameter contra-rotating propellers.
Another important factor is internal construction. Some stealth aircraft have skin that is radar transparent or absorbing, behind which are structures termed reentrant triangles. Radar waves penetrating the skin get trapped in these structures, reflecting off the internal faces and losing energy. This method was first used on the Blackbird series: A-12, YF-12A, Lockheed SR-71 Blackbird.
The most efficient way to reflect radar waves back to the emitting radar is with orthogonal metal plates, forming a corner reflector consisting of either a dihedral (two plates) or a trihedral (three orthogonal plates). This configuration occurs in the tail of a conventional aircraft, where the vertical and horizontal components of the tail are set at right angles. Stealth aircraft such as the F-117 use a different arrangement, tilting the tail surfaces to reduce corner reflections formed between them. A more radical method is to omit the tail, as in the B-2 Spirit. The B-2's clean, low-drag flying wing configuration gives it exceptional range and reduces its radar profile.[34][35] The flying wing design most closely resembles a so-called infinite flat plate (as vertical control surfaces dramatically increase RCS), the perfect stealth shape, as it would have no angles to reflect back radar waves.[36]
YF-23 S-duct engine air intake conceals engine from probing radar waves
In addition to altering the tail, stealth design must bury the engines within the wing or fuselage, or in some cases where stealth is applied to an extant aircraft, install baffles in the air intakes, so that the compressor blades are not visible to radar. A stealthy shape must be devoid of complex bumps or protrusions of any kind, meaning that weapons, fuel tanks, and other stores must not be carried externally. Any stealthy vehicle becomes un-stealthy when a door or hatch opens.
Parallel alignment of edges or even surfaces is also often used in stealth designs. The technique involves using a small number of edge orientations in the shape of the structure. For example, on the F-22A Raptor, the leading edges of the wing and the tail planes are set at the same angle. Other smaller structures, such as the air intake bypass doors and the air refueling aperture, also use the same angles. The effect of this is to return a narrow radar signal in a very specific direction away from the radar emitter rather than returning a diffuse signal detectable at many angles. The effect is sometimes called "glitter" after the very brief signal seen when the reflected beam passes across a detector. It can be difficult for the radar operator to distinguish between a glitter event and a digital glitch in the processing system.
Stealth airframes sometimes display distinctive serrations on some exposed edges, such as the engine ports. The YF-23 has such serrations on the exhaust ports. This is another example in the parallel alignment of features, this time on the external airframe.
Similarly, coating the cockpit canopy with a thin filmtransparent conductor (vapor-deposited gold or indium tin oxide) helps to reduce the aircraft's radar profile, because radar waves would normally enter the cockpit, reflect off objects (the inside of a cockpit has a complex shape, with a pilot helmet alone forming a sizeable return), and possibly return to the radar, but the conductive coating creates a controlled shape that deflects the incoming radar waves away from the radar. The coating is thin enough that it has no adverse effect on pilot vision.
Dielectriccomposite materials are more transparent to radar, whereas electrically conductive materials such as metals and carbon fibers reflect electromagnetic energy incident on the material's surface. Composites may also contain ferrites to optimize the dielectric and magnetic properties of a material for its application.
Radiation-absorbent material (RAM), often as paints, are used especially on the edges of metal surfaces. While the material and thickness of RAM coatings can vary, the way they work is the same: absorb radiated energy from a ground- or air-based radar station into the coating and convert it to heat rather than reflect it back.[39] Current technologies include dielectric composites and metal fibers containing ferrite isotopes. Ceramic composite coating is a new type of material systems which can sustain at higher temperatures with better sand erosion resistance and thermal resistance.[40] Paint comprises depositing pyramid-like colonies on the reflecting superficies with the gaps filled with ferrite-based RAM. The pyramidal structure deflects the incident radar energy in the maze of RAM. One commonly used material is called iron ball paint.[41] It contains microscopic iron spheres that resonate in tune with incoming radio waves and dissipate most of their energy as heat, leaving little to reflect back to detectors. FSS are planar periodic structures that behave like filters to electromagnetic energy. The considered frequency-selective surfaces are composed of conducting patch elements pasted on the ferrite layer. FSS are used for filtration and microwave absorption.
Radar stealth countermeasures and limits
Low-frequency radar
Shaping offers far fewer stealth advantages against low-frequency radar. If the radar wavelength is roughly twice the size of the target, a half-wave resonance effect can still generate a significant return. However, low-frequency radar is limited by lack of available frequencies (many are heavily used by other systems), by lack of accuracy of the diffraction-limited systems given their long wavelengths, and by the radar's size, making it difficult to transport. A long-wave radar may detect a target and roughly locate it, but not provide enough information to identify it, target it with weapons, or even to guide a fighter to it.[42]
Multiple emitters
Stealth aircraft attempt to minimize all radar reflections, but are specifically designed to avoid reflecting radar waves back in the direction they came from (since in most cases a radar emitter and receiver are in the same location). They are less able to minimize radar reflections in other directions. Thus, detection can be better achieved if emitters are in different locations from receivers. One emitter separate from one receiver is termed bistatic radar; one or more emitters separate from more than one receiver is termed multistatic radar. Proposals exist to use reflections from emitters such as civilian radio transmitters, including cellular telephone radio towers.[43]
Moore's law
By Moore's law the processing power behind radar systems is rising over time. This will eventually erode the ability of physical stealth to hide vehicles.[44][45]
Ship wakes and spray
Synthetic aperture sidescan radars can be used to detect the location and heading of ships from their wake patterns.[46] These are detectable from orbit.[47] When a ship moves through a seaway it throws up a cloud of spray which can be detected by radar.[48]
Acoustic stealth plays a primary role for submarines and ground vehicles. Submarines use extensive rubber mountings to isolate, damp, and avoid mechanical noises that can reveal locations to underwater passive sonar arrays.
Early stealth observation aircraft used slow-turning propellers to avoid being heard by enemy troops below. Stealth aircraft that stay subsonic can avoid being tracked by sonic boom. The presence of supersonic and jet-powered stealth aircraft such as the SR-71 Blackbird indicates that acoustic signature is not always a major driver in aircraft design, as the Blackbird relied more on its very high speed and altitude.
One method to reduce helicopter rotor noise is modulated blade spacing.[49] Standard rotor blades are evenly spaced, and produce greater noise at a given frequency and its harmonics. Using varied spacing between the blades spreads the noise or acoustic signature of the rotor over a greater range of frequencies.[50]
The simplest technology is visual camouflage; the use of paint or other materials to color and break up the lines of a vehicle or person.
Most stealth aircraft use matte paint and dark colors, and operate only at night. Lately, interest in daylight Stealth (especially by the USAF) has emphasized the use of gray paint in disruptive schemes, and it is assumed that Yehudi lights could be used in the future to hide the airframe (against the background of the sky, including at night, aircraft of any colour appear dark[51]) or as a sort of active camouflage. The original B-2 design had wing tanks for a contrail-inhibiting chemical, alleged by some to be chlorofluorosulfonic acid,[52] but this was replaced in the final design with a contrail sensor that alerts the pilot when he should change altitude[53] and mission planning also considers altitudes where the probability of their formation is minimized.
In space, mirrored surfaces can be employed to reflect views of empty space toward known or suspected observers; this approach is compatible with several radar stealth schemes. Careful control of the orientation of the satellite relative to the observers is essential, and mistakes can lead to detectability enhancement rather than the desired reduction.
An exhaust plume contributes a significant infrared signature. One means to reduce IR signature is to have a non-circular tail pipe (a slit shape) to minimize the exhaust cross sectional area and maximize the mixing of hot exhaust with cool ambient air (see Lockheed F-117 Nighthawk, rectangular nozzles on the Lockheed Martin F-22, and serrated nozzle flaps on the Lockheed Martin F-35). Often, cool air is deliberately injected into the exhaust flow to boost this process (see Ryan AQM-91 Firefly and Northrop B-2 Spirit). The Stefan–Boltzmann law shows how this results in less energy (Thermal radiation in infrared spectrum) being released and thus reduces the heat signature. In some aircraft, the jet exhaust is vented above the wing surface to shield it from observers below, as in the Lockheed F-117 Nighthawk, and the unstealthy Fairchild Republic A-10 Thunderbolt II. To achieve infrared stealth, the exhaust gas is cooled to the temperatures where the brightest wavelengths it radiates are absorbed by atmospheric carbon dioxide and water vapor, greatly reducing the infrared visibility of the exhaust plume.[54] Another way to reduce the exhaust temperature is to circulate coolant fluids such as fuel inside the exhaust pipe, where the fuel tanks serve as heat sinks cooled by the flow of air along the wings.[55]
Ground combat includes the use of both active and passive infrared sensors. Thus, the United States Marine Corps (USMC) ground combat uniform requirements document specifies infrared reflective quality standards.[56]
In addition to reducing infrared and acoustic emissions, a stealth vehicle must avoid radiating any other detectable energy, such as from onboard radars, communications systems, or RF leakage from electronics enclosures. The F-117 uses passive infrared and low light level television sensor systems to aim its weapons and the F-22 Raptor has an advanced LPI radar which can illuminate enemy aircraft without triggering a radar warning receiver response.
Measuring
The size of a target's image on radar is measured by the radar cross section (RCS), often represented by the symbol σ and expressed in square meters. This does not equal geometric area. A perfectly conducting sphere of projected cross sectional area 1 m2 (i.e. a diameter of 1.13 m) will have an RCS of 1 m2. Note that for radar wavelengths much less than the diameter of the sphere, RCS is independent of frequency. Conversely, a square flat plate of area 1 m2 will have an RCS of σ=4π A2 / λ2 (where A=area, λ=wavelength), or 13,982 m2 at 10GHz if the radar is perpendicular to the flat surface.[57] At off-normal incident angles, energy is reflected away from the receiver, reducing the RCS. Modern stealth aircraft are said to have an RCS comparable with small birds or large insects,[58] though this varies widely depending on aircraft and radar.
If the RCS was directly related to the target's cross-sectional area, the only way to reduce it would be to make the physical profile smaller. Rather, by reflecting much of the radiation away or by absorbing it, the target achieves a smaller radar cross section.[59]
Tactics
Stealthy strike aircraft such as the Lockheed F-117 Nighthawk, are usually used against heavily defended enemy sites such as command and control centers or surface-to-air missile (SAM) batteries. Enemy radar will cover the airspace around these sites with overlapping coverage, making undetected entry by conventional aircraft nearly impossible. Stealthy aircraft can also be detected, but only at short ranges around the radars; for a stealthy aircraft there are substantial gaps in the radar coverage. Thus a stealthy aircraft flying an appropriate route can remain undetected by radar. Even if a stealth aircraft is detected, fire-control radars operating in C, X and Ku bands cannot paint (for missile guidance) low observable (LO) jets except at very close ranges.[60] Many ground-based radars exploit Doppler filter to improve sensitivity to objects having a radial velocity component relative to the radar. Mission planners use their knowledge of enemy radar locations and the RCS pattern of the aircraft to design a flight path that minimizes radial speed while presenting the lowest-RCS aspects of the aircraft to the threat radar. To be able to fly these "safe" routes, it is necessary to understand an enemy's radar coverage (see electronic intelligence). Airborne or mobile radar systems such as airborne early warning and control (AEW&C, AWACS) can complicate tactical strategy for stealth operation.
Research
After the invention of electromagnetic metasurfaces, the conventional means to reduce RCS have been improved significantly.[61][62][63] As mentioned earlier, the main objective in purpose shaping is to redirect scattered waves away from the backscattered direction, which is usually the source. However, this usually compromises aerodynamic performance.[64] One feasible solution, which has extensively been explored in recent time, is to use metasurfaces which can redirect scattered waves without altering the geometry of a target.[61][62][63] Such metasurfaces can primarily be classified in two categories: (i) checkerboard metasurfaces, (ii) gradient index metasurfaces. Similarly, negative index metamaterials are artificial structures for which refractive index has a negative value for some frequency range, such as in microwave, infrared, or possibly optical.[65] These offer another way to reduce detectability, and may provide electromagnetic near-invisibility in designed wavelengths.
Plasma stealth is a phenomenon proposed to use ionized gas, termed a plasma, to reduce RCS of vehicles. Interactions between electromagnetic radiation and ionized gas have been studied extensively for many purposes, including concealing vehicles from radar. Various methods might form a layer or cloud of plasma around a vehicle to deflect or absorb radar, from simpler electrostatic to radio frequency (RF) more complex laser discharges, but these may be difficult in practice.[66]
Several technology research and development efforts exist to integrate the functions of aircraft flight control systems such as ailerons, elevators, elevons, flaps, and flaperons into wings to perform the aerodynamic purpose with the advantages of lower RCS for stealth, via simpler geometries and lower complexity (mechanically simpler, fewer or no moving parts or surfaces, less maintenance), and lower mass, cost (up to 50% less), drag (up to 15% less during use), and inertia (for faster, stronger control response to change vehicle orientation to reduce detection). Two promising approaches are flexible wings, and fluidics.
In fluidics, fluid injection into airflows is being researched for use in aircraft to control direction, in two ways: circulation control and thrust vectoring. In both, larger more complex mechanical parts are replaced by smaller, simpler, lower mass fluidic systems, in which larger forces in fluids are diverted by smaller jets or flows of fluid intermittently, to change the direction of vehicles. Mechanical control surfaces that must move cause an important part of aircraft radar cross-section.[70][71][72] Omitting mechanical control surfaces can reduce radar returns.[72][73][74]As of 2023[update], at least two countries are known to be researching fluidic control. In Britain, BAE Systems has tested two fluidically controlled unmanned aircraft, one starting in 2010 named Demon,[73][72] and another starting in 2017 named MAGMA, with the University of Manchester.[74] In the United States, the Defense Advanced Research Projects Agency (DARPA) program named Control of Revolutionary Aircraft with Novel Effectors (CRANE) seeks "... to design, build, and flight test a novel X-plane that incorporates active flow control (AFC) as a primary design consideration. ... In 2023, the aircraft received its official designation as X-65."[75][76] In January 2024, construction began, at Boeing subsidiary Aurora Flight Sciences.[77][78] According to DARPA, the Aurora X-65 could be completed and unveiled as soon as early 2025, with the first flight occurring in summer 2025.[77][78]
Navy ships worldwide have incorporated signature-reduction features, mostly for the purpose of reducing anti-ship missile detection range and enhancing countermeasure effectiveness rather than actual detection avoidance. Such ships include:
Pyotr Ufimtsev – Soviet-Russian physicist who created much of the original theory behind radar stealth
Related Research Articles
The Northrop B-2 Spirit, also known as the Stealth Bomber, is an American heavy strategic bomber, featuring low-observable stealth technology designed to penetrate dense anti-aircraft defenses. A subsonic flying wing with a crew of two, the plane was designed by Northrop as the prime contractor, with Boeing, Hughes, and Vought as principal subcontractors, and was produced from 1987 to 2000. The bomber can drop conventional and thermonuclear weapons, such as up to eighty 500-pound class (230 kg) Mk 82 JDAM GPS-guided bombs, or sixteen 2,400-pound (1,100 kg) B83 nuclear bombs. The B-2 is the only acknowledged in-service aircraft that can carry large air-to-surface standoff weapons in a stealth configuration.
The Lockheed F-117 Nighthawk is a retired American single-seat, subsonic twin-engine stealth attack aircraft developed by Lockheed's secretive Skunk Works division and operated by the United States Air Force (USAF). It was the first operational aircraft to be designed with stealth technology.
The Lockheed Martin/Boeing F-22 Raptor is an American twin-engine, all-weather, supersonic stealth fighter aircraft. As a product of the United States Air Force's Advanced Tactical Fighter (ATF) program, the aircraft was designed as an air superiority fighter, but also incorporates ground attack, electronic warfare, and signals intelligence capabilities. The prime contractor, Lockheed Martin, built most of the F-22 airframe and weapons systems and conducted final assembly, while program partner Boeing provided the wings, aft fuselage, avionics integration, and training systems.
The fourth-generation fighter is a class of jet fighters in service from around 1980 to the present, and represents design concepts of the 1970s. Fourth-generation designs are heavily influenced by lessons learned from the previous generation of combat aircraft. Third-generation fighters were often designed primarily as interceptors, being built around speed and air-to-air missiles. While exceptionally fast in a straight line, many third-generation fighters severely lacked in maneuverability, as doctrine held that traditional dogfighting would be impossible at supersonic speeds. In practice, air-to-air missiles of the time, despite being responsible for the vast majority of air-to-air victories, were relatively unreliable, and combat would quickly become subsonic and close-range. This would leave third-generation fighters vulnerable and ill-equipped, renewing an interest in manoeuvrability for the fourth generation of fighters. Meanwhile, the growing costs of military aircraft in general and the demonstrated success of aircraft such as the McDonnell Douglas F-4 Phantom II gave rise to the popularity of multirole combat aircraft in parallel with the advances marking the so-called fourth generation.
Stealth aircraft are designed to avoid detection using a variety of technologies that reduce reflection/emission of radar, infrared, visible light, radio frequency (RF) spectrum, and audio, all collectively known as stealth technology. The F-117 Nighthawk was the first operational aircraft explicitly designed around stealth technology. Other examples of stealth aircraft include the B-2 Spirit, the B-21 Raider, the F-22 Raptor, the F-35 Lightning II, the Chengdu J-20, and the Sukhoi Su-57.
Elevons or tailerons are aircraft control surfaces that combine the functions of the elevator and the aileron, hence the name. They are frequently used on tailless aircraft such as flying wings. An elevon that is not part of the main wing, but instead is a separate tail surface, is a stabilator.
The Northrop/McDonnell Douglas YF-23 is an American single-seat, twin-engine, stealth fighter technology demonstrator prototype designed for the United States Air Force (USAF). The design team, with Northrop as the prime contractor, was a finalist in the USAF's Advanced Tactical Fighter (ATF) demonstration/validation competition, battling the YF-22 team for full-scale development and production. Two YF-23 prototypes were built.
The Lockheed Martin X-44 MANTA was an American conceptual aircraft design by Lockheed Martin that has been studied by NASA and the U.S. Air Force. It was intended to test the feasibility of full yaw, pitch and roll authority without tailplanes. Attitude control would rely purely on 3D thrust vectoring. The aircraft design was derived from the F-22 Raptor and featured a stretched delta wing without tail surfaces.
The Advanced Tactical Fighter (ATF) was a program undertaken by the United States Air Force to develop a next-generation air superiority fighter to replace the F-15 Eagle in order to counter emerging worldwide threats in the 1980s, including Soviet Sukhoi Su-27 and Mikoyan MiG-29 fighters under development, Beriev A-50 airborne warning and control systems (AWACS), and increasingly sophisticated surface-to-air missile systems. The ATF would make a leap in performance and capability by taking advantage of emerging technologies, including advanced avionics and flight control systems, more powerful propulsion systems, and stealth technology.
Radar cross-section (RCS), denoted σ, also called radar signature, is a measure of how detectable an object is by radar. A larger RCS indicates that an object is more easily detected.
The Lockheed/Boeing/General Dynamics YF-22 is an American single-seat, twin-engine, stealth fighter technology demonstrator prototype designed for the United States Air Force (USAF). The design team, with Lockheed as the prime contractor, was a finalist in the USAF's Advanced Tactical Fighter (ATF) competition, and two prototypes were built for the demonstration/validation phase. The YF-22 team won the contest against the YF-23 team for full-scale development and the design was developed into the Lockheed Martin F-22. The YF-22 has a similar aerodynamic layout and configuration as the F-22, but with notable differences in the overall shaping such as the position and design of the cockpit, tail fins and wings, and in internal structural layout.
The Boeing Bird of Prey is an American black project aircraft, intended to demonstrate stealth technology. It was developed by McDonnell Douglas and Boeing in the 1990s. The company provided $67 million of funding for the project; it was a low-cost program compared to many other programs of similar scale. It developed technology and materials which would later be used on Boeing's X-45 unmanned combat air vehicle. As an internal project, this aircraft was not given an X-plane designation. There are no public plans to make this a production aircraft. It is characterized as a technology demonstrator.
Lockheed Have Blue was the code name for Lockheed's proof of concept demonstrator for a stealth fighter. Have Blue was designed by Lockheed's Skunk Works division, and tested at Groom Lake, Nevada. The Have Blue was the first fixed-wing aircraft whose external shape was defined by radar engineering rather than by aerospace engineering. The aircraft's faceted shape was designed to deflect electromagnetic waves in directions other than that of the originating radar emitter, greatly reducing its radar cross-section.
A stealth ship is a ship that employs stealth technology construction techniques in an effort to make it harder to detect by one or more of radar, visual, sonar, and infrared methods.
The Lockheed Senior Prom was a classified black project conducted by the United States Air Force in conjunction with the Lockheed Corporation's Skunk Works for the development and testing of a cruise missile using stealth technology. Based on the company's Have Blue demonstrator, the six Senior Prom vehicles proved successful in testing conducted at Area 51 in the late 1970s; despite this, the aircraft was not selected to enter production, and the program was terminated in the early 1980s.
Stealth helicopters are helicopters that incorporate stealth technology to decrease an enemy's detection ability. There are a diverse range of technologies used to achieve this decreased detectability; these have largely involved the reduction of several different signatures typically generated by a rotorcraft, including those of noise, radar, and infrared.
Infrared signature, as used by defense scientists and the military, is the appearance of objects to infrared sensors. An infrared signature depends on many factors, including the shape and size of the object, temperature, and emissivity, reflection of external sources from the object's surface, the background against which it is viewed and the waveband of the detecting sensor. As such there is no all-encompassing definition of infrared signature nor any trivial means of measuring it. For example, the infrared signature of a truck viewed against a field will vary significantly with changing weather, time of day and engine loading.
Aircraft camouflage is the use of camouflage on military aircraft to make them more difficult to see, whether on the ground or in the air. Given the possible backgrounds and lighting conditions, no single scheme works in every situation. A common approach has been a form of countershading, the aircraft being painted in a disruptive pattern of ground colours such as green and brown above, sky colours below. For faster and higher-flying aircraft, sky colours have sometimes been used all over, while helicopters and fixed-wing aircraft used close to the ground are often painted entirely in ground camouflage. Aircraft flying by night have often been painted black, but this actually made them appear darker than the night sky, leading to paler night camouflage schemes. There are trade-offs between camouflage and aircraft recognition markings, and between camouflage and weight. Accordingly, visible light camouflage has been dispensed with when air superiority was not threatened or when no significant aerial opposition was anticipated.
Ground vehicles using stealth technology have come to fruition at various times in history.
Cooperative Engagement Capability (CEC) is a sensor network with integrated fire control capability that is intended to significantly improve battle force air and missile defense capabilities by combining data from multiple battle force air search sensors on CEC-equipped units into a single, real-time, composite track picture. This will greatly enhance fleet air defense by making jamming more difficult and allocating defensive missiles on a battle group basis.
References
↑ Rao, G.A.; Mahulikar, S.P. (2002). "Integrated review of stealth technology and its role in airpower". Aeronautical Journal. 106 (1066): 629–641. doi:10.1017/S0001924000011702. S2CID108545502.
1 2 Richelson, J.T. (10 September 2001). "Science, Technology and the CIA". The National Security Archive. The George Washington University. Retrieved 6 October 2009.
1 2 Merlin, Peter W. (5–8 January 2009). Design and Development of the Blackbird: Challenges and Lessons Learned(PDF). 47th AIAA Aerospace Sciences Meeting Including The New Horizons Forum and Aerospace Exposition. Orlando, Florida: American Institute of Aeronautics and Astronautics. Archived from the original(PDF) on 18 October 2013. Retrieved 6 October 2009.
↑ Hepcke, Gerhard (2007). The Radar War, 1930–1945(PDF) (Report). English translation by Hannah Liebmann (in German). Radar World. p.45. Retrieved 1 February 2024.
1 2 Pedlow, Gregory W.; Welzenbach, Donald E. (1992). The Central Intelligence Agency and Overhead Reconnaissance: The U-2 and OXCART Programs, 1954–1974 (Report). Washington, DC: Central Intelligence Agency.
↑ National Air Intelligence Center, Wright-Patterson AFB, OH, 1971. Technical Report AD 733203, Defense Technical Information Center of USA, Cameron Station, Alexandria, VA, 22304-6145, USA
↑ Browne, M.W. "Two rival designers led the way to stealthy warplanes", The New York Times, Sci. Times Sec., 14 May 1991.
↑ Browne, M.W. "Lockheed credits Soviet theory in design of F-117", Aviation Week Space Technology p. 27, December 1991.
↑ Rich, Ben and L. Janos, Skunk Works, Little Brown, Boston, 1994.
↑ Writing for the American Institute of Aeronautics and Astronautics, J. Seddon and E. L. Goldsmith noted that "Due to its all-wing shape, small vertical fin, and buried engines, at some angles [The Avro Vulcan] was nearly invisible to radar".[31]
↑ MIT's "The Tech – online edition" article Detection of the B-2 Stealth Bomber and a Brief History on "Stealth" by Tao Yue published 30 November 2001 in (Volume 121, Issue 63)
↑ Bush, Vannevar; Conant, James; Harrison, George (1946). "Camouflage of Sea-Search Aircraft"(PDF). Visibility Studies and Some Applications in the Field of Camouflage. Office of Scientific Research and Development, National Defence Research Committee. pp.225–240. Archived from the original(PDF) on 23 October 2013. Retrieved 12 February 2013.
↑ Kopp, Carlo (November 1989 – January 1990). "Optical Warfare – The New Frontier". Australian Aviation. 1989 (November). Australian Aviation (original). Retrieved 23 June 2019.
↑ "Analogues of Stealth"(PDF) (analysis paper). Northrop Grumman. 27 April 2012. Archived(PDF) from the original on 19 February 2018. Retrieved 10 April 2019.
1 2 A. Y. Modi; M. A. Alyahya; C. A. Balanis; C. R. Birtcher, "Metasurface-Based Method for Broadband RCS Reduction of Dihedral Corner Reflectors with Multiple Bounces," in IEEE Transactions on Antennas and Propagation, vol.67, no.12, pp. -, Dec. 2019. doi:10.1109/TAP.2019.2940494
1 2 Modi, A. Y.; Balanis, C. A.; Birtcher, C. R.; Shaman, H. (January 2019). "New Class of RCS-Reduction Metasurfaces Based on Scattering Cancellation Using Array Theory". IEEE Transactions on Antennas and Propagation. 67 (1): 298–308. Bibcode:2019ITAP...67..298M. doi:10.1109/TAP.2018.2878641. S2CID58670543.
1 2 Modi, A. Y.; Balanis, C. A.; Birtcher, C. R.; Shaman, H. (October 2017). "Novel Design of Ultra-Broadband Radar Cross Section Reduction Surfaces using Artificial Magnetic Conductors". IEEE Transactions on Antennas and Propagation. 65 (10): 5406–5417. Bibcode:2017ITAP...65.5406M. doi:10.1109/TAP.2017.2734069. S2CID20724998.
↑ Kota, Sridhar; Osborn, Russell; Ervin, Gregory; Maric, Dragan; Flick, Peter; Paul, Donald. "Mission Adaptive Compliant Wing – Design, Fabrication and Flight Test"(PDF). Ann Arbor, Michigan; Dayton, Ohio; United States: FlexSys Inc., Air Force Research Laboratory. Archived from the original(PDF) on 22 March 2012. Retrieved 26 April 2011.
Ufimtsev, Pyotr Ya., "Method of edge waves in the physical theory of diffraction," Moscow, Russia: Izd-vo. Sov. Radio [Soviet Radio Publishing], 1962, pages 1–243.
United States Patent No.6,297,762. 2 October 2001. Electronic countermeasures system (Apparatus for detecting the difference in phase between received signals at two spaced antennas and for then retransmitting equal amplitude antiphase signals from the two spaced antennas is disclosed.)
Gal-Or, Benjamin (1990). "Multiaxis Thrust Vectoring Flight Control vs Catastrophic Failure Prevention". Vectored Propulsion, Supermanoeuvreability, and Robot Aircraft. Reports to U.S. Dept. of Transportation/FAA, Technical Center, ACD-210, FAA X88/0/6FA/921000/4104/T1706D, FAA Res. Grant-Award No: 94-G-24, CFDA, No. 20.108, 26 December 1994. Springer Verlag. ISBN0-387-97161-0. and 3-540-97161-0.
Suhler, Paul A. (2009). From Rainbow to Gusto: Stealth and the Design of the Lockheed Blackbird. American Institute of Aeronautics and Astronautics. ISBN978-1-60086-712-5.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
