The Bermuda sloop is a historical type of fore-and-aft rigged single-masted sailing vessel developed on the islands of Bermuda in the 17th century. Such vessels originally had gaff rigs with quadrilateral sails, but evolved to use the Bermuda rig with triangular sails. Although the Bermuda sloop is often described as a development of the narrower-beamed Jamaica sloop, which dates from the 1670s, the high, raked masts and triangular sails of the Bermuda rig are rooted in a tradition of Bermudian boat design dating from the earliest decades of the 17th century. [1] It is distinguished from other vessels with the triangular Bermuda rig, which may have multiple masts or may not have evolved in hull form from the traditional designs.
Jamaica was the locus of building fast single-masted vessels that became the model for small cruisers of the Royal Navy. Building of this type of vessel had become more active in Bermuda by the start of 18th century. [1] Bermuda shipbuilders constructed sloops and other vessels, starting in the mid 17th century. Their sloops were gaff-rigged. The first triangular mainsails, characteristic of the Bermuda rig, were introduced on coastal vessels by the 1620s, but most sea-going vessels were gaff-rigged until the 1820s. The sloops were constructed in a range of sizes up to 70 feet (21 m). The most prevalent size for such sloops was in the range of 22 to 28 feet (6.7 to 8.5 m) on deck with a long bowsprit. [1]
Jamaican sloops [1] had beams that were narrower than ocean-going Bermuda sloops, and could attain a speed of around 12 knots. [2] They carried gaff rig, whereas in modern usage, a Bermuda sloop excludes any gaff rig. Jamaican sloops were built usually out of cedar trees, for much the same reasons that Bermudian shipwrights favoured Bermuda cedar: these were very resistant to rot, grew very fast and tall, and had a taste displeasing to marine borers. [3] Cedar was favoured over oak as the latter would rot in about 10 years, while cedar would last for nigh on 30 years and was considerably lighter than oak. [3] When the ships needed to be de-fouled from seaweed and barnacles, pirates needed a safe haven on which to careen the ship. Sloops were well suited for this because they were able to sail in shallow areas where larger ships would either run aground or be unable to sail through at all. These shallow waters also provided protection from ships of the British Royal Navy, which tended to be larger and required deep water to sail safely. [3]
Later in the 19th century, the design of Bermudian vessels had largely dispensed with square topsails and gaff rig, replacing them with triangular main sails and jibs. The Bermuda rig had traditionally been used on vessels with two or more masts, with the gaff rig favoured for single-masted vessels. The reason for this was the increased height necessary for a single mast, which led to too much canvas. The solid wooden masts at that height were also too heavy, and not sufficiently strong. Single-masted sloops quickly became the norm in Bermudian racing, with the introduction of hollow masts and other refinements. [4]
The colony's lightweight Bermuda cedar vessels were widely prized for their agility and speed, especially upwind. The high, raked masts and long bowsprits and booms favoured in Bermuda allowed its vessels of all sizes to carry vast areas of sail when running down-wind with spinnakers and multiple jibs, allowing great speeds to be reached. Bermudian work boats, mostly small sloops, were ubiquitous on the archipelago's waters in the 19th century, moving freight, people, and everything else about. The rig was eventually adopted almost universally on small sailing craft in the 20th Century, although as seen on most modern vessels it is very much less extreme than on traditional Bermudian designs, with lower, vertical masts, shorter booms, omitted bowsprits, and much less area of canvas. [4]
The Bermuda sloop became the predominant type of sailing vessel both in the Bermudian colony and among sloop rigs worldwide as Bermudian traders visited foreign nations. Soon, shipbuilding became one of the primary trades on the island and ships were exported throughout the English colonies on the American seaboard, in the West Indies, and eventually to Europe. In service of the burgeoning shipbuilding industry, many Bermudian colonists began to cultivate Bermuda cedar instead of lucrative trade crops such as tobacco. The archipelago’s ruling Somers Isles Company, who favored tobacco agriculture, attempted to limit Bermudian shipbuilding, inciting demonstrations, appeals, and unrest. This unrest led to violence, the eventual dissolution of the Somers Isles Company and the archipelago’s transition to royal colony status in 1684. [5]
Bermudians, largely slaves, built roughly a thousand ships during the 18th century. Although many of these were sold abroad, the colony maintained its own large merchant fleet which, thanks partly to the domination of trade in many American seaboard ports by branches of wealthy Bermudian families and partly to the suitability and availability of Bermudian vessels, carried much of the produce exported from the American south to Bermuda and to the West Indies aboard Bermudian mostly slave-manned vessels sailed southwest (more-or-less upwind) to the Turk Islands, where salt was harvested. This salt was carried to North American ports and sold at high profits. Bermudian vessels also developed a trade in moving goods such as grain, cocoa, brandy, wine and more from the Atlantic seaboard colonies to the West Indies. [6]
The threat of piracy and privateering was a large problem for mariners of all nations during the 17th and 18th centuries, but it was also as widely popular an enterprise. During wartime, much of Bermuda's merchant fleet turned to more lucrative labors: privateering. The evasive capabilities highly prized by merchantmen also made Bermuda sloops the ship of choice for the pirates themselves, earlier in the 18th century, as well as for smugglers. [7] They often carried sufficient crew out to return with several prizes, and these extra crew were useful both as movable ballast, and in handling the labor-intensive sloops. The shape of the ship enabled Bermudian mariners to excel. The same abilities allowed Bermuda sloops to escape from better-armed privateers and even larger Man-of-war British naval ships which, with their square rigs, could not sail as closely to windward. The ability of the sloop rig in general to sail upwind meant a Bermuda sloop could outrun most other sailing ships by simply turning upwind and leaving its pursuers floundering in its wake. [6]
Despite Bermudian privateers preying heavily on American shipping during the American War of Independence, some historians credit the large number of Bermuda sloops (reckoned at well over a thousand) built in Bermuda as privateers and sold illegally to the Americans as enabling the rebellious colonies to win their independence. [6]
The commercial success of the Bermuda sloop must be credited to the contribution of Bermuda's free and enslaved Blacks. For most of the 17th century, Bermuda's agricultural economy was reliant on indentured servants. This meant that slavery did not play the same role as in many other colonies, though privateers based in Bermuda often brought enslaved blacks and Native Americans who had been captured along with ships of enemy nations. The first large influx of blacks was of free men who came as indentured servants in the middle of the century from former Spanish colonies in the West Indies (the increasing numbers of black, Spanish-speaking probable-Catholics alarmed the white Protestant majority, who were also alarmed by native Irish sent to Bermuda to be sold into servitude after the Cromwellian conquest of Ireland, and measures were taken to discourage black immigration and to ban the importation of Irish). After 1684, Bermuda turned wholesale to a maritime economy, and slaves, black, Amerindian, and Irish (the various minorities merged into a single demographic group, known as coloured, which included anyone who was not defined as entirely of European extraction), played an increasing role in this. Black Bermudians became highly skilled shipwrights, blacksmiths and joiners. Many of the shipwrights who helped to develop shipbuilding in the American South, especially on the Virginia shore of the Chesapeake (Bermuda, also known as Virgineola, had once been part of Virginia, and had maintained close connections ever since), were black Bermudian slaves, and the design and success of the area's schooners owes something to them, also. [8]
Due to the large number of white Bermudian men who were away at sea at any one time (and possibly due as much to fear of the larger number of enslaved black Bermudian men left behind) it was mandated that blacks must make up a percentage of the crew of every Bermudian vessel. [9] By the American War of Independence, the use of many able black slaves as sailors added considerably to the power of the Bermudian merchant fleet due to their highly needed skill set, and these included the crews of Bermudian privateers. When the Americans captured the Bermudian privateer Regulator, they discovered that virtually all of her crew were black slaves. Authorities in Boston offered these men their freedom, but nearly all of the 70 captives elected to be treated as prisoners of war, claiming slavery was all they knew and out of fear for their families who were still in Bermuda. Sent to New York on the sloop Duxbury, those who were left seized the vessel and sailed it back to Bermuda. [10] [9]
Slavery was not abolished in Bermuda until ordered by the British Government in 1834, the Royal Navy had already made frequent use of Bermuda sloops in suppressing the trans-Atlantic slave trade (having formed the West Africa Squadron to this end in 1808, following passage of the Slave Trade Act 1807). [9]
The term Bermuda sloop was also to describe the working boats historically used for moving freight about Bermuda's islands, for fishing, and other coastal activities, and today is used to designate any single-masted yacht with Bermuda rig. Motor vehicles were banned in Bermuda until after the Second World War, and the roads were few and poor until the requirements of that war advanced their development. Boats, as a consequence, remained the primary method of moving people and materials around Bermuda well into the 20th century. [11] Although such small sloops are rare today, the design was further scaled down to produce the Bermuda Fitted Dinghy, a class of racing vessel used in traditional competition between Bermudian yacht clubs. The term Bermuda sloop has come to be used outside Bermuda, today, to describe any single masted, Bermuda rigged boat, also known as Marconi sloops, although most are far less extreme in their design than was once the norm in Bermuda, with bowsprits omitted, masts vertical and shortened, and booms similarly shortened. Spinnaker booms and multiple jibs are rarely seen. The reduced sail area makes modern boats much more manageable, especially for small or inexperienced crews. [12]
Bermuda was first documented by a European in 1503 by Spanish explorer Juan de Bermúdez. In 1609, the English Virginia Company, which had established Jamestown in Virginia two years earlier, permanently settled Bermuda in the aftermath of a hurricane, when the crew and passengers of Sea Venture steered the ship onto the surrounding reef to prevent it from sinking, then landed ashore. Bermuda's first capital, St. George's, was established in 1612.
A sloop is a sailboat with a single mast typically having only one headsail in front of the mast and one mainsail aft of (behind) the mast. Such an arrangement is called a fore-and-aft rig, and can be rigged as a Bermuda rig with triangular sails fore and aft, or as a gaff-rig with triangular foresail(s) and a gaff rigged mainsail.
A schooner is a type of sailing vessel defined by its rig: fore-and-aft rigged on all of two or more masts and, in the case of a two-masted schooner, the foremast generally being shorter than the mainmast. A common variant, the topsail schooner also has a square topsail on the foremast, to which may be added a topgallant. Differing definitions leave uncertain whether the addition of a fore course would make such a vessel a brigantine. Many schooners are gaff-rigged, but other examples include Bermuda rig and the staysail schooner.
A sailboat or sailing boat is a boat propelled partly or entirely by sails and is smaller than a sailing ship. Distinctions in what constitutes a sailing boat and ship vary by region and maritime culture.
A sailing vessel's rig is its arrangement of masts, sails and rigging. Examples include a schooner rig, cutter rig, junk rig, etc. A rig may be broadly categorized as "fore-and-aft", "square", or a combination of both. Within the fore-and-aft category there is a variety of triangular and quadrilateral sail shapes. Spars or battens may be used to help shape a given kind of sail. Each rig may be described with a sail plan—formally, a drawing of a vessel, viewed from the side.
A brigantine is a two-masted sailing vessel with a fully square-rigged foremast and at least two sails on the main mast: a square topsail and a gaff sail mainsail. The main mast is the second and taller of the two masts.
A brig is a type of sailing vessel defined by its rig: two masts which are both square-rigged. Brigs originated in the second half of the 18th century and were a common type of smaller merchant vessel or warship from then until the latter part of the 19th century. In commercial use, they were gradually replaced by fore-and-aft rigged vessels such as schooners, as owners sought to reduce crew costs by having rigs that could be handled by fewer men. In Royal Navy use, brigs were retained for training use when the battle fleets consisted almost entirely of iron-hulled steamships.
A tall ship is a large, traditionally-rigged sailing vessel. Popular modern tall ship rigs include topsail schooners, brigantines, brigs and barques. "Tall ship" can also be defined more specifically by an organization, such as for a race or festival.
A topsail ("tops'l") is a sail set above another sail; on square-rigged vessels further sails may be set above topsails.
In the 18th century and most of the 19th, a sloop-of-war in the Royal Navy was a warship with a single gun deck that carried up to eighteen guns. The rating system covered all vessels with 20 guns and above; thus, the term sloop-of-war encompassed all the unrated combat vessels, including the very small gun-brigs and cutters. In technical terms, even the more specialised bomb vessels and fireships were classed as sloops-of-war, and in practice these were employed in the sloop role when not carrying out their specialised functions.
A mainsail is a sail rigged on the main mast of a sailing vessel.
A cutter is a name for various types of watercraft. It can apply to the rig of a sailing vessel, to a governmental enforcement agency vessel, to a type of ship's boat which can be used under sail or oars, or, historically, to a type of fast-sailing vessel introduced in the 18th century, some of which were used as small warships.
Gaff rig is a sailing rig in which the sail is four-cornered, fore-and-aft rigged, controlled at its peak and, usually, its entire head by a spar (pole) called the gaff. Because of the size and shape of the sail, a gaff rig will have running backstays rather than permanent backstays.
A Bermuda rig, Bermudian rig, or Marconi rig is a configuration of mast and rigging for a type of sailboat and is the typical configuration for most modern sailboats. This configuration was developed in Bermuda in the 17th century; the term Marconi, a reference to the inventor of the radio, Guglielmo Marconi, became associated with this configuration in the early 20th century, because the wires that stabilize the mast of a Bermuda rig reminded observers of the wires on early radio masts.
A fractional rig on a sailing vessel consists of a foresail, such as a jib or genoa sail, that does not reach all the way to the top of the mast.
The junk rig, also known as the Chinese lugsail, Chinese balanced lug sail, or sampan rig, is a type of sail rig in which rigid members, called battens, span the full width of the sail and extend the sail forward of the mast.
The Bermuda Fitted Dinghy is a type of racing-dedicated sail boat used for competitions between the yacht clubs of Bermuda. Although the class has only existed for about 130 years, the boats are a continuance of a tradition of boat and ship design in Bermuda that stretches back to the earliest decades of the 17th century.
Literally, the word pinisi refers to a type of rigging of Indonesian sailing vessels. A pinisi carries seven to eight sails on two masts, arranged like a gaff-ketch with what is called 'standing gaffs' — i.e., unlike most Western ships using such a rig, the two main sails are not opened by raising the spars they are attached to, but the sails are 'pulled out' like curtains along the gaffs which are fixed at around the centre of the masts.
Spirit of Bermuda is a modern-built Bermuda sloop. She is a replica of a Royal Navy sloop-of-war, depicted in a well-known 1831 painting.
The following outline is provided as an overview of and topical guide to sailing: