 | This article needs additional citations for verification .(January 2021) |
Body jewelry sizes express the thickness of an item of body jewelry, using one of several possible systems.
| | This article needs additional citations for verification .(January 2021) |
Body jewelry sizes express the thickness of an item of body jewelry, using one of several possible systems.
Items of body piercing jewelry have an important common factor: the diameter of the part of the item of jewelry where it will rest in the piercing site. With the wearing of European-traditional kinds of earrings, that thickness is not an issue, because jewelry is made to use only thin wire for support, and the wearer need only have a narrow piercing hole to accommodate it. But with body jewelry, there is a wide variety of possible sizes, and wearers generally want jewelry that is the same size as their piercing site. Some wearers want increasingly larger sizes to deliberately stretch the hole. So that wearers can choose the size they want, there are standards for body jewelry sizes, used by jewelry makers and sellers.
Generally, the system of gauge-and-inches is used: In gauge notation, jewelry less than 1⁄2″ thick is typically measured in a system originally devised for measuring wire thickness. A gauge number denotes a thickness on a standardized scale which, for most purposes, starts at 20g (0.812 mm thick— often used for the posts for nose studs), and increases in thickness (as the gauge number decreases) to 0g, then 00g, and rarely goes any further as these thicknesses come closer and closer to 1⁄2″. From there, sizes of 1⁄2″ and thicker are always specified in fractions of an inch. (But note that sizes thinner than1⁄2″ are also sometimes specified as fractions of an inch; see the Conversion Table to see how these interleave with gauges.)
Even though the gauge system was originally meant for wire, it is now used regardless of whether an item of body jewelry is an actual wire, or is instead a wooden plug, a plastic ring, or any other material.
The alternative to using the gauge-and-inches system is to specify the thickness in millimeters.
| gauge (AWG) | diameter | ||
|---|---|---|---|
| inches fractional | inches decimal | millimeters | |
| 20 | · | 0.0320 | 0.812 |
| 18 | · | 0.0403 | 1.024 |
| 16 | · | 0.0508 | 1.291 |
| · | 1⁄16 | 0.0625 | 1.588 |
| 14 | · | 0.0641 | 1.628 |
| 12 | · | 0.0808 | 2.05 |
| 10 | · | 0.1019 | 2.58 |
| · | 1⁄8 | 0.1250 | 3.18 |
| 8 | · | 0.1285 | 3.26 |
| 6 | · | 0.1620 | 4.12 |
| · | 3⁄16 | 0.1875 | 4.76 |
| 4 | · | 0.204 | 5.19 |
| · | 1⁄4 | 0.250 | 6.35 |
| 2 | · | 0.258 | 6.54 |
| · | 5⁄16 | 0.312 | 7.94 |
| 0 | · | 0.325 | 8.25 |
| 00 | · | 0.365 | 9.27 |
| · | 3⁄8 | 0.375 | 9.52 |
| 000 | · | 0.410 | 10.40 |
| · | 7⁄16 | 0.438 | 11.11 |
| 0000 | · | 0.460 | 11.68 |
| · | 1⁄2 | 0.500 | 12.70 |
| · | 9⁄16 | 0.562 | 14.29 |
| · | 5⁄8 | 0.625 | 15.88 |
| · | 11⁄16 | 0.688 | 17.46 |
| · | 3⁄4 | 0.750 | 19.05 |
| · | 13⁄16 | 0.812 | 20.6 |
| · | 7⁄8 | 0.875 | 22.2 |
| · | 15⁄16 | 0.938 | 23.8 |
| · | 1 | 1.000 | 25.4 |
| · | 1+1⁄16 | 1.062 | 27.0 |
| · | 1+1⁄8 | 1.125 | 28.6 |
| · | 1+3⁄16 | 1.188 | 30.2 |
| · | 1+1⁄4 | 1.250 | 31.8 |
| · | 1+5⁄16 | 1.312 | 33.3 |
| · | 1+3⁄8 | 1.375 | 34.9 |
| · | 1+7⁄16 | 1.438 | 36.5 |
| · | 1+1⁄2 | 1.500 | 38.1 |
| · | 1+9⁄16 | 1.562 | 39.7 |
| · | 1+5⁄8 | 1.625 | 41.3 |
| · | 1+11⁄16 | 1.688 | 42.9 |
| · | 1+3⁄4 | 1.750 | 44.4 |
| · | 1+13⁄16 | 1.812 | 46.0 |
| · | 1+7⁄8 | 1.875 | 47.6 |
| · | 1+15⁄16 | 1.938 | 49.2 |
| · | 2 | 2.000 | 50.8 |
Some jewelry makers or sellers who express the size of their jewelry in millimeters, may also list the nearest approximate gauge-and-inches measurements for each item. [1] Using millimeters as the primary notation is most common in Europe and Australia.
Discussions of gauge in this article use the American Wire Gauge (AWG) scale. Some jewelry may use the significantly different Standard Wire Gauge (SWG) scale instead, particularly jewelry from Canada or the United Kingdom where the SWG scale is used. [2] Both AWG and SWG express sizes as a gauge, but the numbers are different. For example, AWG 12g is 2.1 mm, but SWG 12g is 2.6 mm. AWG 8g happens to be the same as SWG 10g. AWG 000g is 10.4 mm, but SWG 000g is 9.4 mm.
In most discussions of body jewelry, sizes are specified by giving the gauge, usually abbreviated by the suffix "g", the same symbol as used for grams: "12g". The article American Wire Gauge system, section "Nomenclature and abbreviations in electrical distribution" shows other notations for gauge, but most are rarely used for expressing body jewelry sizes, except "ga." as in "12 ga.", which is used occasionally.
United States customary units form a system of measurement units commonly used in the United States and most U.S. territories, since being standardized and adopted in 1832. The United States customary system developed from English units that were in use in the British Empire before the U.S. became an independent country. The United Kingdom's system of measures was overhauled in 1824 to create the imperial system, which was officially adopted in 1826, changing the definitions of some of its units. Consequently, while many U.S. units are essentially similar to their imperial counterparts, there are noticeable differences between the systems.
A micrometer, sometimes known as a micrometer screw gauge, is a device incorporating a calibrated screw widely used for accurate measurement of components in mechanical engineering and machining as well as most mechanical trades, along with other metrological instruments such as dial, vernier, and digital calipers. Micrometers are usually, but not always, in the form of calipers. The spindle is a very accurately machined screw and the object to be measured is placed between the spindle and the anvil. The spindle is moved by turning the ratchet knob or thimble until the object to be measured is lightly touched by both the spindle and the anvil.
Gauge may refer to:
American Wire Gauge (AWG) is a logarithmic stepped standardized wire gauge system used since 1857, predominantly in North America, for the diameters of round, solid, nonferrous, electrically conducting wire. Dimensions of the wires are given in ASTM standard B 258. The cross-sectional area of each gauge is an important factor for determining its current-carrying capacity.
Metrication is the process of introducing the International System of Units, also known as SI units or the metric system, to replace a jurisdiction's traditional measuring units. U.S. customary units have been defined in terms of metric units since the 19th century, and the SI has been the "preferred system of weights and measures for United States trade and commerce" since 1975 according to United States law. However, conversion was not mandatory and many industries chose not to convert, and U.S. customary units remain in common use in many industries as well as in governmental use. There is government policy and metric (SI) program to implement and assist with metrication, however there is major social resistance for further metrication.
In typography, the point is the smallest unit of measure. It is used for measuring font size, leading, and other items on a printed page. The size of the point has varied throughout printing's history. Since the 18th century, the size of a point has been between 0.18 and 0.4 millimeters. Following the advent of desktop publishing in the 1980s and 1990s, digital printing has largely supplanted the letterpress printing and has established the desktop publishing (DTP) point as the de facto standard. The DTP point is defined as 1⁄72 of an inch and, as with earlier American point sizes, is considered to be 1⁄12 of a pica.
Stretching, in the context of body piercing, is the deliberate expansion of a healed piercing for the purpose of wearing certain types of jewelry. Ear piercings are the most commonly stretched piercings, with nasal septum piercings, tongue piercings and lip piercings/lip plates following close behind. While all piercings can be stretched to some degree, cartilage piercings are usually more difficult to stretch and more likely to form hypertrophic scars if stretched quickly. Dermal punching is generally the preferred method for accommodating larger jewelry in cartilage piercings.
IEC 60228 is the International Electrotechnical Commission (IEC)'s international standard on conductors of insulated cables. As of 2023 the current version is Third Edition 2004-11 Among other things, it defines a set of standard wire cross-sectional areas:
Wire gauge is a measurement of wire diameter. This determines the amount of electric current the wire can safely carry, as well as its electrical resistance and weight.
Ring size is a measurement used to denote the circumference of jewellery rings and smart rings.
Automotive tires are described by an alphanumeric tire code or tyre code, which is generally molded into the sidewall of the tire. This code specifies the dimensions of the tire, and some of its key limitations, such as load-bearing ability, and maximum speed. Sometimes the inner sidewall contains information not included on the outer sidewall, and vice versa.
The Birmingham gauge is a wire gauge system, and is also used to specify thickness or diameter of hypodermic needles and tube products.
A circular mil is a unit of area, equal to the area of a circle with a diameter of one mil. It corresponds to approximately 5.067×10−4 mm2. It is a unit intended for referring to the area of a wire with a circular cross section. As the definition of the unit contains π, it is easy to calculate area values in circular mils when the diameter in mils is known.
A thousandth of an inch is a derived unit of length in a system of units using inches. Equal to 1⁄1000 of an inch, a thousandth is commonly called a thou or, particularly in North America, a mil.
Jewelry wire is wire, usually copper, brass, nickel, aluminium, silver, or gold, used in jewelry making.
Grammage and basis weight, in the pulp and paper industry, are the area density of a paper product, that is, its mass per unit of area. Two ways of expressing grammage are commonly used:
British Standard Wire Gauge is a unit for denoting wire size given by BS 3737:1964. It is also known as the Imperial Wire Gauge or British Standard Gauge. Use of SWG sizes has fallen greatly in popularity, but they are still used as a measure of thickness in guitar strings and some electrical wire. Cross sectional area in square millimetres is now the more usual size measurement for wires used in electrical installation cables. The current British Standard for metallic materials such as wire and sheet is BS 6722:1986, which is a solely metric standard.
A tube, or tubing, is a long hollow cylinder used for moving fluids or to protect electrical or optical cables and wires.
Copper tubing is available in two basic types of tube—plumbing tube and air conditioning/refrigeration (ACR) tube, and in both drawn (hard) and annealed (soft) tempers. Because of its high level of corrosion resistance, it is used for water distribution systems, oil fuel transfer lines, non-flammable medical-gas systems, and as a refrigerant line in HVAC systems. Copper tubing is joined using flare connection, compression connection, pressed connection, or solder.
FASTON terminals or faston terminals are connectors that are widely used in electronic and electrical equipment. These terminals are manufactured by many companies, commonly using the terms "quick disconnect", "quick connect", "tab" terminals, "spade" terminals or blade connectors; without qualifiers, the first two could be mistaken for plumbing connections.