High Capacity Metro Train | |
---|---|
Stock type | Electric multiple unit |
In service | 2020–present |
Manufacturer | Evolution Rail (Downer Rail, CRRC Changchun and Plenary Group) |
Assembly | Newport Workshops |
Built at | Changchun, China (bodyshells) |
Constructed | 2018-2024 |
Entered service | 27 December 2020 |
Number built | 70 [1] |
Number in service | 65 |
Formation | 7-car sets Tc–DMp–Mp1–DT–Mp2–DMp–Tc |
Fleet numbers | 01–70 [1] |
Capacity |
|
Operators | Metro Trains Melbourne |
Depots |
|
Lines served |
|
Specifications | |
Train length | 160,196 mm (525 ft 6+15⁄16 in) |
Car length |
|
Width | 3.04 m (9 ft 11+11⁄16 in) |
Height | 4,186 mm (13 ft 8+13⁄16 in) |
Floor height | 1.17 m (3 ft 10 in) |
Entry | Level |
Doors | 6 per carriage, 3 per side |
Maximum speed | 130 km/h (81 mph) |
Weight | 316.9 t (311.9 long tons; 349.3 short tons) |
Axle load |
|
Traction system | Times Electric IGBT–VVVF [5] |
Traction motors | ABB 3-phase AC induction motor [5] |
Electric system(s) | 1,500 V DC (nominal) from overhead catenary |
Current collector(s) | Pantograph |
Safety system(s) | West Footscray to Clayton only: Bombardier CITYFLO 650 CBTC [6] (referred to as "High Capacity Signalling" by the Victorian Government [7] ) |
Coupling system | Dellner |
Seating | 502 [3] |
Track gauge | 1,600 mm (5 ft 3 in) broad gauge |
The High Capacity Metro Train (HCMT) is a type of electric multiple unit (EMU) train for use by Metro Trains Melbourne on the Melbourne rail network. The first train set entered service on 27 December 2020 and will become the primary rolling stock used in the Metro Tunnel when it opens in 2025.
The HCMTs carry around 1,400 passengers in seven carriages, running on Melbourne's 1,500 V DC overhead catenary system, and are currently the most advanced trains in the Metro Trains fleet. A consortium of investors and rail companies are constructing the trains in China and Australia via a contract with the Victorian Government, in addition to upgrade works necessary for the operation of the trains.
The HCMTs currently run all services on the Cranbourne and Pakenham lines, alongside two morning test services on the Sunbury line.
The previous major procurement of rolling stock for the Melbourne rail network occurred in 2002, when franchisees M>Train and Connex ordered 62 Siemens Nexas and 58 X'Trapolis 100 trains respectively, as part of their franchise agreements to replace the older Hitachi trains. [8] [9] However, the Siemens units suffered major braking issues over the following decade, causing their repeated withdrawal from service; [10] when the State Government tendered for 18 further six-carriage trains in 2007, it restricted bids to the previous two models ordered and awarded the contract to Alstom. [11] Several further orders were placed for X'Trapolis trains over the next 10 years.
The Public Transport Development Authority (later branded as Public Transport Victoria) was created in 2011 by the newly elected state government of Premier Ted Baillieu with the intent of, among other things, running major studies into the operation of the metropolitan rail network. [12] The Network Development Plan – Metropolitan Rail (NDPMR), released publicly in early 2013 in the partial fulfillment of this objective, was designed as a series of concrete proposals for the expansion and consolidation of the rail network over the following 20 years. [13] The NDPMR's first stage, intended to be completed before 2016, acknowledged the need for an interim solution of several more X'Trapolis trains to overcome major constraints, [14] as well as recommending the internal reconfiguration of Siemens and Comeng trains to increase capacity, [15] but identified the provision of new rolling stock as critical to the cost-effective use of existing railway infrastructure. [16]
Among the deficiencies of existing rolling stock noted by the NDPMR were "multi-purpose" designs intended to strike a balance between commuter rail and metro operations, and the failure of existing trains to use the entire length of metropolitan platforms. [16] The NDPMR rejected double-decker trains on the basis that they would increase dwell time at crowded stations, and argued that 220-metre (721 ft 9 in) trains, formed by operating the existing three car sets as nine car trains, would require extensive and prohibitively expensive infrastructure works, particularly in the City Loop. Instead, it recommended the procurement of single-level trains with a fixed number of cars, increased standing room and a length of 153 metres (502 ft 0 in), with the capacity for expansion to 220 m (721 ft 9 in) upon the opening of the Metro Tunnel. The NDPMR envisaged these trains with a maximum capacity of 1,100 and 1,600 passengers respectively. [17]
The NDPMR envisaged that these high-capacity trains would completely replace the Comeng fleet by 2032, and be used primarily on the Sunshine–Dandenong line created by the Metro Tunnel. Furthermore, it identified the need for the new trains to include cab signalling to reduce the headway required between trains, and for the construction of new maintenance facilities at several points on the network. [18]
Prior to the 2014 state election, then-Premier Denis Napthine promised an order of 25 of the proposed high-capacity trains if his incumbent Liberal-National Coalition state government was returned for a second term. [19] [20] This was part of an unsolicited proposal put forward to the government by train operator Metro Trains Melbourne, and the proposal would also involve the upgrade of the Pakenham and Cranbourne lines. The trains would be built by UGL Rail, who was a partial owner of Metro Trains Melbourne.
The Coalition's proposal was criticised by the Labor opposition led by Daniel Andrews, labelling it a "con", and that 25 trains were "not enough to meet future passenger numbers". The Coalition subsequently lost the 2014 election and the proposal did not go ahead under the new Labor state government, who instead announced a different proposal in March 2015. [21] Labor's proposal would involve the purchase of 37 new trains via expressions of interest, and an expanded scope of the Pakenham and Cranbourne line upgrades. [22]
In June 2015, expressions of interest were requested for the 37 new trains to be delivered and maintained for the Melbourne rail network. [23] In November 2015, three consortia were shortlisted to build and maintain the 37 trains: [24]
In March 2016, the order was increased to 65. [25]
In September 2016, the contract was awarded to the Evolution Rail consortium. New depots to maintain the trains will be built in Pakenham East and Calder Park. [26] [27] By September of the following year, a full-scale mock-up of two carriages had been constructed and was presented to Minister for Public Transport Jacinta Allan. [28] The mock-up was made available to drivers, technicians, representatives of the Public Transport Users Association and passenger groups including the visually impaired and those with physical disabilities. The Evolution Rail consortium noted that this last stage in the design process marked the fulfilment of the project's first major contractual obligation. [29]
In late 2017, the Locomotive Division of the Victorian Rail Tram and Bus Union lodged proceedings in the Federal Court of Australia against Metro Trains, claiming that the consortium, government and Metro planned to introduce a lower standard of training for operators of the HCMT. It furthermore refused to support the implementation of the new rolling stock unless all electric train drivers were trained in the operation of the HCMT. [30] Among the union's objections to the project are the necessary changes in work practice and the increased automation of certain processes. [31] This followed criticism by the Australian Workers' Union of the decision to award the contract to Evolution Rail instead of Bombardier, the latter of which had an established manufacturing operation in Dandenong. [32] The government announced the awarding of several subcontracts for the project in December. [33]
The mockup carriages used for the consultation phase were placed on public display at Birrarung Marr from 9–17 February 2018. The display concluded during Melbourne's White Night event with a light show. [34]
By June of that year, manufacturing had commenced, with the first body shells arriving at Newport Workshops from CRRC's facility in China. [35]
On 9 May 2022 the Victorian Government announced it was procuring an additional 5 HCMT sets for use on the Melbourne Airport rail link, to bring the total order to 70. [36]
The trains are being delivered as a public–private partnership (PPP) between the State of Victoria and Evolution Rail Pty Ltd, under the Partnerships Victoria agency. The initial contract specified that the consortium would be responsible for the design, construction and delivery of 65 trains, as well as the construction of a heavy maintenance facility and depot in Pakenham East, the construction of a light maintenance facility in Calder Park, and the provision of two simulators for driver training. It also stated that the consortium would be responsible for the maintenance of the HCMTs throughout their lifetime, as well as the operation and maintenance of the depots and simulators over the same time frame. [37]
Evolution Rail is a consortium composed of CRRC Changchun Railway Vehicles, Downer Rail and Plenary Group. [32]
CRRC Changchun is leading the development and design for the HCMTs, and is manufacturing the train bodies as a joint venture with Downer Rail. At least 60% of construction is "local content" from the Victorian manufacturing supply chain. Downer leads the delivery and maintenance of the sets, as well as the construction of the new rail yard facilities. [38] Frames for bogies will be manufactured by Hoffman Engineering in Bendigo. [39] The Australian arm of Times Electric is manufacturing the traction motors and other electrical systems in Morwell, and SIGMA Air Conditioning is building the heating and cooling systems in Derrimut. [33] Assembly of wheel sets and bogies is being performed by Downer at Newport Workshops. Plenary Group is responsible for the financial management of the project, and the debt is financed by a group of investment banks led by Westpac. [40]
The contract did not prescribe specific design elements of the HCMTs, but required that the design fulfil a number of objectives, centred on the provision of a "safe and comfortable journey for passengers". [41]
The total value of the PPP was around $2.3 billion. [31]
The first revenue service for the HCMT was the 8:31am service from Pakenham on the Pakenham line on 27 December 2020. This was an extra service and regular timetabled services didn't commence until 31 January 2021, when the new PTV timetable was introduced. [42] In 2021, high-capacity signalling began being installed on the Cranbourne, Pakenham and Sunbury lines for use by the HCMTs, and the trains began operating revenue services under the new communications-based moving block system in October 2023. [43] [44] HCMTs were progressively rolled out from 2020 until by 2023 they were operating all suburban revenue services on the Cranbourne and Pakenham lines. [45]
Two HCMTs entered the Metro Tunnel in 2023 to begin testing for the opening of service through the tunnel, running at the top tunnel speed of 80 km/h by August 2023. [46]
On 30 October 2023, HCMTs were introduced into revenue service on the Sunbury Line, with two services running in the morning peak from Sunbury to Flinders Street station, then continuing on to the Pakenham line. [47] This followed power upgrades, new signalling and platform extensions as part of the Sunbury Line Upgrade to allow for the trains. [48] A further 34 trains will complete the Sunbury line fleet when the Metro Tunnel opens in 2025. [47]
The HCMT are based on the Type A design used by CRRC Changchun. [29] The train is sometimes known by its model number designated by CRRC Changchun, CCD5006, which belongs to its CCD series rapid transit trains. The trains have seven carriages, with a total passenger capacity of 1,380, [2] with the ability to add three more carriages for a capacity of more than 1,970. [49] An aerodynamic nose cone and retractable cover for the couplers at each end of the trains were included to reduce the incidence of train surfing when the HCMTs are in operation. [50] They are designed for easy conversion to dual voltage operation at either 1,500 V DC or 3 kV DC by the installation of an electrical cabinet containing IGBT-based DC-to-DC converter, line reactors and line filters, without needing to modify the traction inverters or traction motors. [51]
Approximately 30–40% of passengers are seated when the train is at full capacity. The standing areas of the train offer multiple types of straps and handles for the safety of standing passengers, and wide doors for rapid ingress and egress from these areas. In addition to seventy passenger information displays (PIDs) in each train, Wi-Fi connections are available throughout the passenger areas. [52] The PIDs show the next station, current time, and the train's location on an adapted rail map. Displays on the front and sides of the train indicate its destination. [53] Twenty-eight wheelchair spaces and wide aisles between seats enable easy access for passengers with disabilities. [2] [49]
A number of semi-automated features are included in the HCMT design, including the capacity for low-speed shunting by remote control and for trains to be started without the presence of a driver. The trains also automatically estimate the passenger load, and the reading can be accessed remotely. [49] Furthermore, the HCMTs include "stopping aids" to maximise accuracy of the position of train's arrival at platforms. Drivers will also have the capacity to open individual doors on the trains. [54]
HCMT rolling stock configuration [3] | |||||||
Car position | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
Pantograph | < | < | > | > | |||
Car type | 90xx (Tc) | 91xx (DMp) | 92xx (Mp1) | 93xx (DT) | 97xx (Mp2) | 98xx (DMp) | 99xx (Tc) |
Main features | Control cab | Inter-car door | Inter-car door | Inter-car door | Control cab | ||
Sanded axles | 0 | 1 | 2 | 0 | 2 | 1 | 0 |
Numbers | 9001 : 9070 | 9101 : 9170 | 9201 : 9270 | 9301 : 9370 | 9701 : 9770 | 9801 : 9870 | 9901 : 9970 |
The City Loop is a piece of underground commuter rail infrastructure in the central business district (CBD) of Melbourne, Victoria, Australia.
Parliament railway station is a commuter railway station in the Melbourne central business district, serving the Melbourne suburb of East Melbourne in Victoria, Australia. Parliament is an underground premium station, featuring four platforms, two island platforms on two floors connected to street level via two underground concourses. It opened on 22 January 1983.
Hawksburn railway station is a commuter railway station located in the southern Melbourne suburb of South Yarra in Victoria, Australia. Hawksburn is a below ground unstaffed station, featuring four platforms with an island platform and two side platforms accessible by a pedestrian bridge. The station is listed on the Victorian Heritage Register, and was opened on 7 May 1879.
Armadale railway station is a commuter railway station in Armadale, a suburb of Melbourne, Victoria, Australia. The station is listed on the Victorian Heritage Register and was opened on 7 May 1879. The station consists of an island platform and two side platforms, all accessed by a pedestrian bridge. There are two principal station buildings located on the central platform and on platform 4, consisting of a small two and one-story brick buildings. These buildings were provided in 1914 as ticketing and staff offices. The station is only partially accessible due to a multiple steep access ramps.
Malvern railway station is a commuter railway station that is part of the Melbourne railway network in Victoria, Australia. The station is located on the southern border of Malvern, a suburb of Melbourne, and was opened on 7 May 1879. The station complex consists of an island platform and two side platforms all accessed by a pedestrian bridge. There are two red brick Edwardian-era station buildings, constructed in 1914 as ticketing and staff offices. The entire complex is listed on the Victorian Heritage Register because of its architectural significance and its role in the development of Malvern as a significant metropolitan centre. The station is only partially accessible because of multiple steep access ramps.
Caulfield railway station is a commuter railway station on the northern boundary of Caulfield East, a suburb of Melbourne, Victoria, Australia. Opened in 1879 and rebuilt from 1913 to 1914, the station complex is listed on the Victorian Heritage Register and is noted as an example of Federation Free Style architecture. It is named after the nearby suburb of Caulfield, located southwest of the station.
Carnegie railway station is a commuter railway station located in the suburb of Carnegie, in the southeastern suburbs of Melbourne, Victoria, Australia. The station originally opened in 1879 as Rosstown. The station received its current name in 1909 alongside the renaming of the suburb. Carnegie is an elevated premium station, consisting of a single island platform connected to the station concourse on Koornang Road via escalators, lifts and a staircase.
Murrumbeena railway station is a commuter railway station on the Pakenham and Cranbourne lines, part of the Melbourne railway network. It serves the south-eastern suburb of Murrumbeena, in Melbourne, Victoria, Australia. Murrumbeena is an elevated premium station, featuring an island platform with two faces. It opened on 14 May 1879, with the current station provided in 2018.
Huntingdale railway station is a commuter railway station located adjacent to the suburbs of Oakleigh and Huntingdale located in the south east of Melbourne, Victoria in Australia. The station originally opened in 1927 as "East Oakleigh". It did not receive its current name until 1954. Huntingdale is a ground-level host station, consisting of a single island platform connected to both Railway Avenue and Haughton Road via a pedestrian subway.
Clayton railway station is a commuter railway station located in the suburb of Clayton, in the south-eastern suburbs of Melbourne, Victoria, Australia. The station originally opened in 1880 as "Clayton's Road". It did not receive its current name until 1890. Clayton is an elevated premium station, consisting of a single island platform connected to the station concourse on Clayton Road via escalators, lifts and a staircase. The station was previously at grade; however, in 2018, a new elevated station was rebuilt as part of the Level Crossing Removal Project.
Sandown Park railway station is a commuter railway station on the Pakenham and Cranbourne lines, which are part of the Melbourne railway network. It serves the south-eastern suburb of Springvale, in Melbourne, Victoria, Australia. Sandown Park station is a ground-level unstaffed station, featuring an island platform. It opened 19 June 1965.
Noble Park railway station is a commuter railway station on the Pakenham and Cranbourne lines, which are part of the Melbourne railway network. It serves the south-eastern suburb of Noble Park, in Melbourne, Victoria, Australia. Noble Park station is an elevated premium station, with an island platform. It opened on 3 February 1913, with the current station provided in 2018.
Yarraman railway station is a commuter railway station located in the suburbs of Noble Park and Dandenong, in Melbourne, Victoria, Australia. The station was named after the nearby Yarraman Creek, a first-order tributary of the lower Dandenong Creek/Patterson River system. Yarraman is a ground-level unstaffed station, featuring an island platform with two faces. It opened on 21 December 1976.
Hallam railway station is a commuter railway station on the Pakenham line, which is part of the Melbourne railway network. It serves the south-eastern suburb of Hallam, in Melbourne, Victoria, Australia. Hallam station is an elevated premium station, featuring two side platforms. It opened on 1 December 1880, with the current station provided in 2022.
The Pakenham line is a commuter railway line on the Melbourne metropolitan railway network serving the city of Melbourne in Victoria, Australia. Operated by Metro Trains Melbourne, the line is coloured light blue and is one of the two lines that constitute the Caulfield group. It is the city's longest metropolitan railway line at 57 kilometres (35 mi). The line runs from Flinders Street station in central Melbourne to East Pakenham station in the south-east, serving 27 stations via South Yarra, Caulfield, Oakleigh, and Dandenong.
The Cranbourne line is a commuter railway line in the city of Melbourne, Victoria, Australia. Operated by Metro Trains Melbourne, it is the city's second longest metropolitan railway line at 44 kilometres (27 mi). The line runs from Flinders Street station in central Melbourne to Cranbourne station in the south-east, serving 24 stations via the City Loop, South Yarra, Caulfield, Oakleigh, and Dandenong. The line operates for approximately 20 hours a day with 24 hour service available on Friday and Saturday nights. During peak hour, headways of up to 5 to 15 minutes are operated with services every 15–20 minutes during off-peak hours. Trains on the Cranbourne line run with a seven-car formation operated by High Capacity Metro Trains.
The Sunbury line is a commuter railway line in the city of Melbourne, Victoria, Australia. Operated by Metro Trains Melbourne, it is the city's fifth longest metropolitan railway line at 40.3 kilometres (25.0 mi). The line runs from Flinders Street station in central Melbourne to Sunbury station in the city's north-west, serving 18 stations via North Melbourne, Sunshine, St Albans, and Watergardens. The line operates for approximately 19 hours a day with 24 hour service available on Friday and Saturday nights. During peak hour, headways of up to 5 minutes are operated with services every 20–30 minutes during off-peak hours. Train sets typically used on the Sunbury line are the Comeng and Siemens Nexas trainsets and, for two morning peak services, the High Capacity Metro Train.
The X'Trapolis 100 is a class of single deck electric multiple units part of Alstom's X'Trapolis family of trains, operated in Melbourne, Victoria, Australia and Valparaíso, Chile.
Metro Trains Melbourne, often known simply as Metro, is the operator and brand name of train services on the electrified metropolitan rail network serving the city of Melbourne, Victoria, Australia. It is the largest urban rail network in Australia, with 17 lines and 221 stations across 405 km (252 mi) of railways, and the second busiest network in Australia, with a patronage of 99.5 million as of 2021–2022.
The Metro Tunnel, formerly known as Melbourne Metro Rail (MMR), is an underground heavy rail project currently under construction in Melbourne, Victoria, Australia. It involves the construction of twin 9-kilometre (5.6 mi) rail tunnels between South Kensington and South Yarra with five new underground stations. The tunnel will connect the Pakenham and Cranbourne lines with the Sunbury line, creating a new high-frequency cross-city line that bypasses Flinders Street station and the City Loop. The line is also planned to serve Melbourne Airport via a new branch line west of Sunshine.
Media related to High Capacity Metro Trains at Wikimedia Commons