The environmental impact of electricity generation from wind power is minor when compared to that of fossil fuel power. [2] Wind turbines have some of the lowest global warming potential per unit of electricity generated: far less greenhouse gas is emitted than for the average unit of electricity, so wind power helps limit climate change. [3] Wind power consumes no fuel, and emits no air pollution, unlike fossil fuel power sources. The energy consumed to manufacture and transport the materials used to build a wind power plant is equal to the new energy produced by the plant within a few months. [4]
Onshore (on-land) wind farms can have a significant visual impact and impact on the landscape. [5] Due to a very low surface power density and spacing requirements, wind farms typically need to be spread over more land than other power stations. [6] [7] Their network of turbines, access roads, transmission lines, and substations can result in "energy sprawl"; [8] although land between the turbines and roads can still be used for agriculture. [9] [10]
Conflicts arise especially in scenic and culturally-important landscapes. Siting restrictions (such as setbacks) may be implemented to limit the impact. [11] The land between the turbines and access roads can still be used for farming and grazing. [9] [12] They can lead to "industrialization of the countryside". [13] Some wind farms are opposed for potentially spoiling protected scenic areas, archaeological landscapes and heritage sites. [14] [15] [16] A report by the Mountaineering Council of Scotland concluded that wind farms harmed tourism in areas known for natural landscapes and panoramic views. [17]
Habitat loss and fragmentation are the greatest potential impacts on wildlife of onshore wind farms, [8] but they are small [18] and can be mitigated if proper monitoring and mitigation strategies are implemented. [19] The worldwide ecological impact is minimal. [2] Thousands of birds and bats, including rare species, have been killed by wind turbine blades, [20] as around other manmade structures, though wind turbines are responsible for far fewer bird deaths than fossil-fuel infrastructure. [21] [22] This can be mitigated with proper wildlife monitoring. [23]
Many wind turbine blades are made of fiberglass and some only had a lifetime of 10 to 20 years. [24] Previously, there was no market for recycling these old blades, [25] and they were commonly disposed of in landfills. [26] Because blades are hollow, they take up a large volume compared to their mass. Since 2019, some landfill operators have begun requiring blades to be crushed before being landfilled. [24] Blades manufactured in the 2020s are more likely to be designed to be completely recyclable. [26]
Wind turbines also generate noise. At a distance of 300 metres (980 ft) this may be around 45 dB, which is slightly louder than a refrigerator. At 1.5 km (1 mi) distance they become inaudible. [27] [28] There are anecdotal reports of negative health effects on people who live very close to wind turbines. [29] Peer-reviewed research has generally not supported these claims. [30] [31] [32] Pile-driving to construct non-floating wind farms is noisy underwater, [33] but in operation offshore wind is much quieter than ships. [34]
Compared with other low-carbon power sources, wind turbines have one of the lowest global warming potentials per unit of electrical energy generated by any power source. [35] According to the IPCC, in assessments of the life-cycle global warming potential of energy sources, wind turbines have a median value of between 15 and 11 (g CO2 eq/kWh) depending on whether offshore or onshore turbines are being assessed. [36] [37]
Wind power doesn't consume water [38] for continuous operation and has near negligible emissions directly related to its electricity production. Wind turbines when isolated from the electric grid, produce negligible amounts of carbon dioxide, carbon monoxide, sulfur dioxide, nitrogen dioxide, mercury and radioactive waste when in operation, unlike fossil fuel sources and nuclear energy station fuel production, respectively.
Wind power externality costs are negligible compared to the cost of electricity generation. [39]
A typical study of a wind farm's Life cycle assessment, when not connected to the electric grid, usually results in similar findings as the following 2006 analysis of 3 installations in the US Midwest, where the carbon dioxide (CO2) emissions of wind power ranged from 14 to 33 tonnes (15 to 36 short tons) per GWh (14–33 g CO2/kWh) of energy produced, with most of the CO2 emission intensity coming from producing steel, concrete, and plastic/fiberglass composites for the turbine structure and foundation. [40] [41] By combining similar data from numerous individual studies in a meta-analysis, the median global warming potential for wind power was found to be 11–12 g CO2/kWh and unlikely to change significantly. [36] [42] [43]
This higher dependence on back-up/Load following power plants to ensure a steady power grid output has the knock-on-effect of more frequent inefficient (in CO2e g/kWh) throttling up and down of these other power sources in the grid to facilitate the intermittent power source's variable output. When one includes the total effect of intermittent sources on other power sources in the grid system, that is, including these inefficient start up emissions of backup power sources to cater for wind energy, into wind energy's total system-wide life cycle, this results in a higher real-world wind energy emission intensity. Higher than the direct g/kWh value that is determined from looking at the power source in isolation and thus ignores all down-stream detrimental/inefficiency effects it has on the grid. This higher dependence on back-up/Load following power plants to ensure a steady power grid output forces fossil power plants to operate in less efficient states. [42] [ better source needed ]
In comparison to other low carbon power sources wind turbines, when assessed in isolation, have a median life cycle emission value of between 11 and 12 (g CO2 eq/kWh). [36] [44] While an increase in emissions due to the practical issues of load balancing is an issue, Pehnt et al. still conclude that these 20 and 80 g CO2-eq/kWh added penalties still result in wind being roughly ten times less polluting than fossil gas and coal which emit ~400 and 900 g CO2-eq/kWh respectively. [45] As these losses occur due to the cycling of fossil power plants, they may at some point become smaller when more than 20–30% of wind energy is added to the power grid, as fossil power plants are replaced, however this has yet to occur in practice. [46] [ better source needed ]
This section needs to be updated. The reason given is: are permanent magnets still used? is neodymium still used?.(November 2022) |
The production of permanent magnets used in some wind turbines makes use of neodymium. [47] Pollution concerns associated with the extraction of this rare-earth element, which is primarily exported by China, have prompted government action in recent years, [48] [49] [ obsolete source ] and international research attempts to refine the extraction process. [50] Research is underway on turbine and generator designs which reduce the need for neodymium, or eliminate the use of rare-earth metals altogether. [51] Additionally, the large wind turbine manufacturer Enercon GmbH chose very early not to use permanent magnets for its direct drive turbines, to avoid responsibility for the adverse environmental impact of rare-earth mining. [52]
The Kleinman Center for Energy Policy at the University of Pennsylvania (May 2021) reports that neodymium, a critical rare-earth element, is used in manufacturing permanent magnets for wind turbines, which helps improve their efficiency and reduce maintenance needs. With China holding over 95% of global Rare Earth Element (REE) production, there are significant environmental and geopolitical concerns. The extraction of REEs, expected to double in demand by 2035 due to renewable energy needs, presents environmental risks, including radioactive waste. Sustainable mining practices, supply diversification, and recycling innovations are being considered to manage the increased demand and environmental risks associated with REE production. [53]
An International Energy Agency study projects the demand for mined resources such as lithium, graphite, cobalt, copper, nickel and rare earths will rise by four times by 2040 and notes insufficient supply of these materials to match demand imposed by expected large-scale deployments of decentralized technologies solar and wind power, and required grid upgrades. [54] [55] According to a 2018 study, significant increase of wind power would require 1000% increase in supply of these metals by 2060, requiring significant increase in mining operations. [56]
Modern wind turbine blades are made from plastic/fiberglass composite designs that provide a service lifetime of less than about 20 years. [24] As of February 2018 [update] , there was no economical technology and market for recycling these old blades, and the most common disposal procedure is to truck them to landfills. [57] Other options for disposing of the blades includes incinerating the material or grinding it up into powder, but both of these methods are not only expensive, but also inefficient and involves additional energy usage. [58] Blade incineration emits a significant[ need quotation to verify ] amount of green house gases, though it can be used as a source of heat and power, which somewhat offsets these emissions. [59] [60] Because of their hollow design for less weight, blades can take up an enormous volume compared to their mass, making road transport difficult, expensive, and dangerous due to wide turning berths, extra safety vehicles, and longer flatbed trucks.
Since many blades are still trashed, landfill operators have started requiring blades to be cut to pieces and sometimes crushed before they can be landfilled, which consumes further energy. [24] [61] However, as they can take a lot of weight they can be made into long lasting small bridges for walkers or cyclists. [62] Along with ongoing development work to extend the generating efficiency and service life of newer turbines, blade recycling solutions continue to be pursued that are economical, energy efficient, and market scalable. [63]
There may be as much as 45% additional waste resulting from processes that occur during the lifecycle of the turbine blades, and it is estimated that total annual blade waste of all countries may reach 2.9 million tons by 2050. [64] In comparison, global solar photovoltaic cell waste is expected to reach about 78 million tons by 2050, [65] and 750 million tons of fly ash waste was produced by coal power in 2022. [66]
As much as 80% of the wind turbine structure can be recycled, though this does not include the foundation of the structure, which is typically made from reinforced concrete, or the blades. [67] Alternatively, these components of the turbine structure that are not easily recycled into new turbines can still be repurposed and used in other ways. [68]
The large volume of the turbine blades, while difficult to handle, is advantageous in repurposing the blades as playground structures, bike shelters and footbridges. Other recycling methods include creating pellets for waterproof boards and injectable plastics, as well as pyrolysis for producing paints, glues, and both cement and concrete. [69] [70] [71] Carbon fiber blades can now be recycled, the fiber first being separated from the epoxy resin binder, then chopped into small particles. After the separation, the resin is used as a fuel source for the next materials to be processed. [72] After pyrolysis, the resulting material can be further separated and the glass fibers extracted to be used in insulation or fiber reinforcement. [73]
The blades may also be repurposed into building materials and structural components. [74] Research indicates that turbine blades could successfully be repurposed as electrical transmission poles as their strength and structural stability was found to be comparable to the materials that are typically used. [75] Sections of the blades have been adapted to create roofs for small houses and these structures meet the requirements of building codes and may prove to be a viable way to reuse blade materials without extensive processes needed to make the material usable. [76] Components of the turbine could be reused by implementing segmentation, where the object is divided into different elements. [77] Research on segmentation suggests that the resulting materials are better than conventional construction materials when measuring specific flexural stiffness and flexural strength. [77]
Overall, there are several different avenues through which wind turbine components can be recycled, reused, or repurposed, all with their advantages and disadvantages, and there continues to be research conducted to determine even more ways that the materials can be economically used. While various methods for recycling or repurposing the turbine blades have been proven effective, they have not been implemented on a large enough scale to adequately address the rapidly rising amounts of turbine blade waste being produced. [78]
In addition to carbon fiber blades sometimes being installed due to lower weight and higher strength and durability compared to fiberglass-epoxy composites, there are wind turbines with a modular wooden structural support trunk, which is stronger, lighter, easier to recycle and transport, and more carbon-neutral than steel. [79] These wooden towers would not need to be recycled as often as steel due to their fire-resistance and higher tolerance of metal-oxidizing chemicals. [80] Other alternative building materials include recyclable polymers (thermoplastic, recyclable thermosets, polyurethane), bamboo, natural fiber composites, biodegradable resins, and bio-based carbon fibers. [73]
Research on wind turbine materials also focuses on how to make the turbine blades more resistant to damage as this would extend their lifespan and reduce the replacement turnover (frequency of replacements). [81] In addition to adapting the materials used in the blades to increase their resistance to damage, there are also potential methods of altering the turbine's activity during certain weather events in order to decrease any damage caused by wind or rain. [82]
Wind power has low life-cycle surface power density of 1.84 W/m2 which is three orders of magnitude (103 times, which is equivalent to 1,000x) less than nuclear or fossil fuel power and three times less than Photovoltaics. [83]
Wind farms are often built on land that has already been impacted by land clearing. The vegetation clearing and ground disturbance required for wind farms are minimal compared with coal mines and coal-fired power stations. If wind farms are decommissioned, the landscape can be returned to its previous condition. [84]
A study by the US National Renewable Energy Laboratory of US wind farms built between 2000 and 2009 found that, on average, 1.1 percent of the total wind farm area suffered surface disturbance, and 0.43 percent was permanently disturbed by wind power installations. On average, there were 63 hectares (160 acres) of total wind farm area per MW of capacity, but only 0.27 hectares (0.67 acres) of permanently disturbed area per MW of wind power capacity. [85]
In the UK many prime wind farm sites – locations with the best average wind speeds – are in upland areas that are frequently covered by blanket bog. This type of habitat exists in areas of relatively high rainfall where large areas of land remain permanently sodden. Construction work may create a risk of disruption to peatland hydrology which could cause localised areas of peat within the area of a wind farm to dry out, disintegrate, and so release their stored carbon. At the same time, the warming climate which renewable energy schemes seek to mitigate could itself pose an existential threat to peatlands throughout the UK. [86] [87] A Scottish MEP campaigned for a moratorium on wind developments on peatlands saying that "Damaging the peat causes the release of more carbon dioxide than wind farms save". [88] A 2014 report for the Northern Ireland Environment Agency noted that siting wind turbines on peatland could release considerable carbon dioxide from the peat, and also damage the peatland contributions to flood control and water quality: "The potential knock-on effects of using the peatland resource for wind turbines are considerable and it is arguable that the impacts on this facet of biodiversity will have the most noticeable and greatest financial implications for Northern Ireland." [89] Wind farm construction near wetlands has been linked to several bog landslides in Ireland that have polluted rivers, such as at Derrybrien (2003) and Meenbog (2020). [90] [91] Such incidents could be prevented with stricter planning procedures and siting guidelines. [92]
Wind-energy advocates contend that less than 1% of the land is used for foundations and access roads, the other 99% can still be used for farming. [12] A wind turbine needs about 200–400 m2 for the foundation. With the increasing size of the wind turbine the relative size of the foundation decreases. [93] Critics point out that on some locations in forests, the clearing of trees around tower bases may be necessary for installation sites on mountain ridges, such as in the northeastern U.S. [94] This usually takes the clearing of 5,000 m2 per wind turbine. [95]
During construction of wind farms in Scotland in 2007–2008, over 3.4 million trees were removed on 6202 acres of forest, out of which 31.5% have been replanted. [96]
Turbines are not generally installed in urban areas. Buildings interfere with the wind, turbines must be sited a safe distance ("setback") from residences in case of failure, and the value of land is high. There are a few notable exceptions to this. The WindShare ExPlace wind turbine was erected in December 2002, on the grounds of Exhibition Place, in Toronto, Ontario, Canada. It was the first wind turbine installed in a major North American urban city centre. [97] Steel Winds also has a 20 MW urban project south of Buffalo, New York. Both of these projects are in urban locations, but benefit from being on uninhabited lakeshore property.
In Greece, wind turbine sites have been installed "on mountain peaks, in forests, near archaeological sites, on islands, in protected habitats" and in highly populated tourist areas, causing disruption to hospitality business and protests of residents. [98] [99]
The land can still be used for farming and cattle grazing. Livestock is unaffected by the presence of wind farms. International experience shows that livestock will "graze right up to the base of wind turbines and often use them as rubbing posts or for shade". [84]
In 2014, a first of its kind veterinary study attempted to determine the effects of rearing livestock near a wind turbine, the study compared the health effects of a wind turbine on the development of two groups of growing geese, preliminary results found that geese raised within 50 meters of a wind turbine gained less weight and had a higher concentration of the stress hormone cortisol in their blood than geese at a distance of 500 meters. [100]
Semi-domestic reindeer avoid the construction activity, [101] but seem unaffected when the turbines are operating. [102] [103]
Environmental assessments are routinely carried out for wind farm proposals, and potential impacts on the local environment (e.g. plants, animals, soils) are evaluated. [84] Turbine locations and operations are often modified as part of the approval process to avoid or minimise impacts on threatened species and their habitats. Unavoidable impacts can be offset with conservation improvements of similar ecosystems which are unaffected by the proposal. [84]
A research agenda from a coalition of researchers from universities, industry, and government, supported by the Atkinson Center for a Sustainable Future, suggests modeling the spatiotemporal patterns of migratory and residential wildlife with respect to geographic features and weather, to provide a basis for science-based decisions about where to site new wind projects. More specifically, it suggests:
Wind turbines, like many other human activities and buildings, also increase the death rate of avian creatures such as birds and bats. A summary of the existing field studies compiled in 2010 from the National Wind Coordinating Collaborative identified fewer than 14 and typically less than four bird deaths per installed megawatt per year, but a wider variation in the number of bat deaths. [105] [ globalize ] Like other investigations, it concluded that some species (e.g. migrating bats and songbirds) are known to be harmed more than others and that factors such as turbine siting can be important. [106] [107] The National Renewable Energy Laboratory maintains a database of the scientific literature on the subject. [108]
The impact of wind energy on birds, which can fly into turbines, or have their habitats degraded by wind development, is complex. Displacement is thought to be more of a threat to species than collisions. [109] Habitat loss is highly variable between species. [110] [111]
Hundreds of thousands of birds, [112] [113] [114] including raptors and migrants, [115] [116] [117] are killed each year because of wind turbines and their power lines, [20] but this is less than the number killed (or not born) because of fossil fuel (coal and gas) infrastructure. [118] [22] Wind farms are estimated to be responsible for losing less than 0.4 birds per gigawatt-hour (GWh) of electricity generated, compared to over 5 birds per GWh for fossil fueled power stations. [119] As well as threatening extinction, [120] one of the effects of climate change is to already cause a decline in bird population, [121] and this is the main cause of bird loss from fossil power. [122] [18] [107] [123] A study comparing annually recorded bird populations in the United States from 2000 to 2020 to the spread of wind power infrastructure, found the presence of wind turbines had no significant effect on bird population numbers. This was directly compared to fracking infrastructure, whose presence causes a 15% decrease in the local bird populations. [124]
On some important migration routes turbines are banned, or birds may alter their flight paths to avoid them. [125] Biological surveys beforehand and correctly siting turbines is important, especially for raptors as they are slow to breed. [118] Methods to help birds avoid turbines include painting of one of the turbine blades black, [126] and making ultrasonic noise. [127] Some approaching birds can be spotted, for example by avian radar, [128] [129] in time for turbines to be slowed to a speed which is safe for them. [130] Wind farms may need more power lines, and lines may be made less damaging to compensate. [131] [132] Making permits for the number of birds (such as eagles) killed tradeable has been suggested, in order to save the most birds at the least cost. [133]
Ecological surveys beforehand with full-spectrum detectors can ensure onshore wind turbines are sited to minimize the impact on bats, [134] however as of 2024 more offshore bat research is needed. [135] Bats may be injured by direct impact with turbine blades, towers, or transmission lines. Bats may also be killed when suddenly passing through a low air pressure region surrounding the turbine blade tips. [136] The numbers of bats killed by existing onshore and near-shore facilities have troubled bat enthusiasts. [137] Studies by the Bats and Wind Energy Cooperative show that bat fatalities can be reduced by stopping wind farm operations when wind speed is low during certain months, at times when bats are most active, and illuminating turbines with UV light is also a deterrent. [138] Bats avoid radar transmitters, and placing microwave transmitters on wind turbine towers may reduce the number of bat collisions. [139] [140]
It is hypothesized that a portion of bat fatalities are attributed to the wind displacement caused by the wind turbine blades as they move through the air causing insects in the area to become disoriented making it a dense area of prey – an attractive hunting ground for bats. [141] To combat this phenomenon, ultrasonic deterrents have been tested on select wind turbines and has been shown to reduce bat fatalities from collision and barotrauma. [141] Testing of the ultrasonic deterrents has shown significantly reduced bat activity around wind turbines. [141]
A 2013 study produced an estimate that wind turbines killed more than 600,000 bats in the U.S. the previous year, with the greatest mortality occurring in the Appalachian Mountains. Some earlier studies had produced estimates of between 33,000 and 888,000 bat deaths per year. [142] Mortality, specifically in migratory birds and bats, seems to be increased in locations where wind patterns seem to facilitate both migration paths and energy production. [143] As of 2024 many countries lack laws to protect bats. [144]
Wind farms designed to be more efficient from lack of airflow-impeding obstacles, offshore wind farms, have altered marine ecosystems by providing refuge from humans in the form of fishing-restricted areas due to safety concerns of moving blades. Interestingly, the regions of refuge are not directly at the location of the wind turbines but rather slightly closer to shore. As an example, new colonies of Blue Mussels in the North Sea fed by phytoplankton are a food source for other predators, namely fish and crabs, and further up the food chain, seals. Blue Mussels also reduce turbidity in the ocean water, making for greater underwater visibility, and leave behind their shells as shelter, further altering possible inhabitants of their coastal domain. [145] [146]
Wind farms may affect weather in their immediate vicinity. Turbulence from spinning wind turbine rotors increases vertical mixing of heat and water vapor that affects the meteorological conditions downwind, including rainfall. [147] Overall, wind farms lead to a slight warming at night and a slight cooling during the day time. This effect can be reduced by using more efficient rotors or placing wind farms in regions with high natural turbulence. Warming at night could "benefit agriculture by decreasing frost damage and extending the growing season. Many farmers already do this with air circulators". [148] [149] [150]
Another study by David Keith and Lee Miller on climactic impacts of wind power, which predicted warming when considering the area of the United States, [151] has been criticized by Mark Z. Jacobson on the grounds of its limited geographical scope, with the argument that a large-scale wind energy extraction would significantly lower global temperatures. [152] [153] [154] [155] [156]
Aesthetic considerations of wind power stations often have a significant role in their evaluation process. [158] To some, the perceived aesthetic aspects of wind power stations may conflict with the protection of historical sites. [159] Wind power stations are less likely to be perceived negatively in urbanized and industrial regions. [160] Aesthetic issues are subjective and some people find wind farms pleasant or see them as symbols of energy independence and local prosperity. [161] While studies in Scotland predict wind farms will damage tourism, [162] in other countries some wind farms have themselves become tourist attractions, [163] [164] [165] with several having visitor centers at ground level or even observation decks atop turbine towers.
In the 1980s, wind energy was being discussed as part of a soft energy path. [166] Renewable energy commercialization led to an increasing industrial image of wind power, which is being criticized by various stakeholders in the planning process, including nature protection associations. [167] Newer wind farms have larger, more widely spaced turbines, and have a less cluttered appearance than older installations. Wind farms are often built on land that has already been impacted by land clearing and they coexist easily with other land uses.
Coastal areas and areas of higher altitude such as ridgelines are considered prime for wind farms, due to constant wind speeds. However, both locations tend to be areas of high visual impact and can be a contributing factor in local communities' resistance to some projects. Both the proximity to densely populated areas and the necessary wind speeds make coastal locations ideal for wind farms. [168]
Wind power stations can impact on important sight relations which are a key part of culturally important landscapes, such as in the Rhine Gorge or Moselle valley. [169] Conflicts between the heritage status of certain areas and wind power projects have arisen in various countries. In 2011 UNESCO raised concerns regarding a proposed wind farm 17 kilometres away from the French island abbey of Mont-Saint-Michel. [170] In Germany, the impact of wind farms on valuable cultural landscapes has implications on zoning and land-use planning. [169] [171] For example, sensitive parts of the Moselle valley and the background of the Hambach Castle, according to the plans of the state government, will be kept free of wind turbines. [172]
Wind turbines require aircraft warning lights, which may create light pollution. Complaints about these lights have caused the US FAA to consider allowing fewer lights per turbine in certain areas. [173] Residents near turbines may complain of "shadow flicker" caused by rotating turbine blades, when the sun passes behind the turbine. This can be avoided by locating the wind farm to avoid unacceptable shadow flicker, or by turning the turbine off for the time of the day when the sun is at the angle that causes flicker. If a turbine is poorly sited and adjacent to many homes, the duration of shadow flicker on a neighbourhood can last hours. [174]
Wind turbines also generate noise, and at a residential distance of 300 metres (980 ft) this may be around 45 dB; however, at a distance of 1.5 km (1 mi), most wind turbines become inaudible. [175] [176] Loud or persistent noise increases stress which could then lead to diseases. [177] Wind turbines do not affect human health with their noise when properly placed. [178] [179] [180] [11] However, when improperly sited, data from the monitoring of two groups of growing geese revealed substantially lower body weights and higher concentrations of a stress hormone in the blood of the first group of geese who were situated 50 meters away compared to a second group which was at a distance of 500 meters from the turbine. [100]
A 2014 study by Health Canada [181] involving 1238 households (representing 79 percent of the households in the geographic area studied) and 4000 hours of testing in Ontario and on Prince Edward Island includes the following supportive statements of wind turbine low frequency noise annoyance in its summary:
"Wind turbines emit low frequency noise, which can enter the home with little or no reduction in energy, potentially resulting in... annoyance."
Regarding the comparison of low frequency wind turbine noise annoyance to transportation noise annoyance, the Health Canada study summary states: "Studies have consistently shown.. that, in comparison to the scientific literature on noise annoyance to transportation noise sources such as rail or road traffic, community annoyance with (low frequency) wind turbine noise begins at a lower sound level and increases more rapidly with increasing wind turbine noise."
The summary also includes the following three findings of its own study:
"Statistically significant exposure-response relationships were found between increasing wind turbine noise levels and the prevalence of reporting high annoyance. These associations were found with annoyance due to noise, vibrations, blinking lights, shadow and visual impacts from wind turbines. In all cases, annoyance increased with increasing exposure to wind turbine noise levels."
"Community annoyance was observed to drop at distances between 1–2 kilometers (0.6 to 1.2 miles) in Ontario." (It dropped at 550 meters (1/3 mile) on Prince Edward Island.)
"Annoyance was significantly lower among the 110 participants who received personal benefit, which could include rent, payments or other indirect benefits of having wind turbines in the area e.g., community improvements."
The above Health Canada summary states that "no statistically significant association was observed between measured blood pressure, resting heart rate, (hair cortisol concentrations) and wind turbine noise exposure."
Wind turbine syndrome, a psychosomatic disorder, pertains to the belief that low frequency wind turbine noise, either directly or through annoyance, causes or contributes to various measurable health effects related to anxiety, for which there is little general evidence. [182]
Many offshore wind farms have contributed to electricity needs in Europe and Asia for years, and as of 2014 the first offshore wind farms were under development in U.S. waters. The offshore wind industry has grown dramatically over the last several decades, especially in Europe and China.
Traditional offshore wind turbines are attached to the seabed in shallower waters near the shore. As offshore wind technologies become more advanced, floating structures have begun to be used in deeper waters where more wind resources exist.
Common environmental concerns associated with offshore wind developments include: [183]
Germany restricts underwater noise during pile driving to less than 160 dB. [185] During construction, heavy equipment generates noise and vibrations that are very well conducted through water and impacting marine life, such as harbour porpoise which rely on sound for navigation underwater. Attempts to partially mitigate the impact involve e.g. building air bubble curtains around the towers. [184]
Due to the landscape protection status of large areas of the Wadden Sea, a major World Heritage Site with various national parks (e.g. Lower Saxon Wadden Sea National Park), German offshore installations are mostly restricted on areas outside the territorial waters. [186] [ better source needed ] Offshore capacity in Germany is therefore way behind the British or Danish near coast installments, which face much lower restrictions.
In 2009, a comprehensive government environmental study of coastal waters in the United Kingdom concluded that there is scope for between 5,000 and 7,000 offshore wind turbines to be installed without an adverse impact on the marine environment. The study –which forms part of the Department of Energy and Climate Change's Offshore Energy Strategic Environmental Assessment –is based on more than a year's research. It included analysis of seabed geology, as well as surveys of sea birds and marine mammals. [187] [188]
A study published in 2014 suggests that some seals prefer to hunt near turbines, likely due to the laid stones functioning as artificial reefs which attract invertebrates and fish. [189]
The turbines are often scaled-up versions of existing land technologies. However, the foundations are unique to offshore wind and are listed below:
Monopile foundations are used in shallow depth applications (0–30 m) and consist of a pile being driven to varying depths into the seabed (10–40 m) depending on the soil conditions. The pile-driving construction process is an environmental concern as the noise produced is loud and propagates far in the water, even after mitigation strategies such as bubble shields, slow start, and acoustic cladding. The footprint is relatively small, but may still cause scouring or artificial reefs. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms. [183] [ need quotation to verify ]
Tripod fixed bottom foundations are used in transitional depth applications (20–80 m) and consist of three legs connecting to a central shaft that supports the turbine base. Each leg has a pile driven into the seabed, though less depth is necessary because of the wide foundation. The environmental effects are a combination of those for monopile and gravity foundations. [183]
Gravity foundations are used in shallow depth applications (0–30 m) and consist of a large and heavy base constructed of steel or concrete to rest on the seabed. The footprint is relatively large and may cause scouring, artificial reefs, or physical destruction of habitat upon introduction. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms. [183]
Gravity tripod foundations are used in transitional depth applications (10–40 m) and consist of two heavy concrete structures connected by three legs, one structure sitting on the seabed while the other is above the water. As of 2013, no offshore windfarms were using this foundation. The environmental concerns are identical to those of gravity foundations, though the scouring effect may be less significant depending on the design. [183]
Floating structure foundations are used in deep depth applications (40–900 m) and consist of a balanced floating structure moored to the seabed with fixed cables. The floating structure may be stabilized using buoyancy, the mooring lines, or a ballast. The mooring lines may cause minor scouring or a potential for collision. Transmission lines also produce an electromagnetic field that may be harmful to some marine organisms. [183]
Renewable energy is energy from renewable natural resources that are replenished on a human timescale. The most widely used renewable energy types are solar energy, wind power, and hydropower. Bioenergy and geothermal power are also significant in some countries. Some also consider nuclear power a renewable power source, although this is controversial. Renewable energy installations can be large or small and are suited for both urban and rural areas. Renewable energy is often deployed together with further electrification. This has several benefits: electricity can move heat and vehicles efficiently and is clean at the point of consumption. Variable renewable energy sources are those that have a fluctuating nature, such as wind power and solar power. In contrast, controllable renewable energy sources include dammed hydroelectricity, bioenergy, or geothermal power.
Wind power is the use of wind energy to generate useful work. Historically, wind power was used by sails, windmills and windpumps, but today it is mostly used to generate electricity. This article deals only with wind power for electricity generation. Today, wind power is generated almost completely with wind turbines, generally grouped into wind farms and connected to the electrical grid.
Tidal power or tidal energy is harnessed by converting energy from tides into useful forms of power, mainly electricity using various methods.
Electric power systems consist of generation plants of different energy sources, transmission networks, and distribution lines. Each of these components can have environmental impacts at multiple stages of their development and use including in their construction, during the generation of electricity, and in their decommissioning and disposal. These impacts can be split into operational impacts and construction impacts. All forms of electricity generation have some form of environmental impact, but coal-fired power is the dirtiest. This page is organized by energy source and includes impacts such as water usage, emissions, local pollution, and wildlife displacement.
A wind farm or wind park, also called a wind power station or wind power plant, is a group of wind turbines in the same location used to produce electricity. Wind farms vary in size from a small number of turbines to several hundred wind turbines covering an extensive area. Wind farms can be either onshore or offshore.
Energy is sustainable if it "meets the needs of the present without compromising the ability of future generations to meet their own needs." Definitions of sustainable energy usually look at its effects on the environment, the economy, and society. These impacts range from greenhouse gas emissions and air pollution to energy poverty and toxic waste. Renewable energy sources such as wind, hydro, solar, and geothermal energy can cause environmental damage but are generally far more sustainable than fossil fuel sources.
Environmental technology (envirotech) is the use of engineering and technological approaches to understand and address issues that affect the environment with the aim of fostering environmental improvement. It involves the application of science and technology in the process of addressing environmental challenges through environmental conservation and the mitigation of human impact to the environment.
Marine currents can carry large amounts of water, largely driven by the tides, which are a consequence of the gravitational effects of the planetary motion of the Earth, the Moon and the Sun. Augmented flow velocities can be found where the underwater topography in straits between islands and the mainland or in shallows around headlands plays a major role in enhancing the flow velocities, resulting in appreciable kinetic energy. The Sun acts as the primary driving force, causing winds and temperature differences. Because there are only small fluctuations in current speed and stream location with minimal changes in direction, ocean currents may be suitable locations for deploying energy extraction devices such as turbines. Other effects such as regional differences in temperature and salinity and the Coriolis effect due to the rotation of the earth are also major influences. The kinetic energy of marine currents can be converted in much the same way that a wind turbine extracts energy from the wind, using various types of open-flow rotors.
Wind turbine design is the process of defining the form and configuration of a wind turbine to extract energy from the wind. An installation consists of the systems needed to capture the wind's energy, point the turbine into the wind, convert mechanical rotation into electrical power, and other systems to start, stop, and control the turbine.
Sensory ecology is a relatively new field focusing on the information organisms obtain about their environment. It includes questions of what information is obtained, how it is obtained, and why the information is useful to the organism.
Wind power in Germany is a growing industry. The installed capacity was 55.6 gigawatts (GW) at the end of 2017, with 5.2 GW from offshore installations. In 2020, 23.3% of the country's total electricity was generated through wind power, up from 6.2% in 2010 and 1.6% in 2000.
Wind power is a branch of the energy industry that has expanded quickly in the United States over the last several years. From January through December 2023, 425.2 terawatt-hours were generated by wind power, or 10.18% of electricity in the United States. The average wind turbine generates enough electricity in 46 minutes to power the average American home for one month. In 2019, wind power surpassed hydroelectric power as the largest renewable energy source in the U.S.
Wind power generates about 10% of Turkey's electricity, mainly in the west in the Aegean and Marmara regions, and is gradually becoming a larger share of renewable energy in the country. As of 2024, Turkey has 12 gigawatts (GW) of wind turbines. The Energy Ministry plans to have almost 30 GW by 2035, including 5 GW offshore.
A wind turbine is a device that converts the kinetic energy of wind into electrical energy. As of 2020, hundreds of thousands of large turbines, in installations known as wind farms, were generating over 650 gigawatts of power, with 60 GW added each year. Wind turbines are an increasingly important source of intermittent renewable energy, and are used in many countries to lower energy costs and reduce reliance on fossil fuels. One study claimed that, as of 2009, wind had the "lowest relative greenhouse gas emissions, the least water consumption demands and the most favorable social impacts" compared to photovoltaic, hydro, geothermal, coal and gas energy sources.
Offshore wind power or offshore wind energy is the generation of electricity through wind farms in bodies of water, usually at sea. There are higher wind speeds offshore than on land, so offshore farms generate more electricity per amount of capacity installed. Offshore wind farms are also less controversial than those on land, as they have less impact on people and the landscape.
A tidal farm is a group of tidal stream generators used for production of electric power. The potential of tidal farms is limited by the number of suitable sites across the globe as there are niche requirements to make a tidal farm cost effective and environmentally conscious.
Policy makers often debate the constraints and opportunities of renewable energy.
Modern United States wind energy policy coincided with the beginning of modern wind industry of the United States, which began in the early 1980s with the arrival of utility-scale wind turbines in California at the Altamont Pass wind farm. Since then, the industry has had to endure the financial uncertainties caused by a highly fluctuating tax incentive program. Because these early wind projects were fueled by investment tax credits based on installation rather than performance, they were plagued with issues of low productivity and equipment reliability. Those investment tax credits expired in 1986, which forced investors to focus on improving the reliability and efficiency of their turbines. The 1990s saw rise to a new type of tax credit, the production tax credit, which propelled technological improvements to the wind turbine even further by encouraging investors to focus on electricity output rather than installation.
The wind lens is a modification on the wind turbine created by Professor Ohya from the Kyushu University as an attempt to be more efficient in production of electricity and less invasive to both humans and nature. While still in progress, the wind lens has a few changes in design which have led to impacts on how wind energy can be used and harnessed while changing how it impacts the world around us. A wind lens works like a ducted fan on an aircraft - it encircles the wind turbine, and speeds air up while protecting the blades from foreign object damage. Because of this, wind turbine efficiency can be drastically increased because of a simple installation of a wind lens.
A vertical-axis wind turbine (VAWT) is a type of wind turbine where the main rotor shaft is set transverse to the wind while the main components are located at the base of the turbine. This arrangement allows the generator and gearbox to be located close to the ground, facilitating service and repair. VAWTs do not need to be pointed into the wind, which removes the need for wind-sensing and orientation mechanisms. Major drawbacks for the early designs included the significant torque ripple during each revolution, and the large bending moments on the blades. Later designs addressed the torque ripple by sweeping the blades helically. Savonius vertical-axis wind turbines (VAWT) are not widespread, but their simplicity and better performance in disturbed flow-fields, compared to small horizontal-axis wind turbines (HAWT) make them a good alternative for distributed generation devices in an urban environment.
The blades are composite, those are not recyclable, those can't be sold," Linowes said. "The landfills are going to be filled with blades in a matter of no time.
The blades are composite, those are not recyclable, those can't be sold," Linowes said. "The landfills are going to be filled with blades in a matter of no time.
Disposing of turbine blades is an issue that will likely linger for years in Iowa. Large, investor-owned Iowa utilities are erecting new turbines and replacing blades to extend the life of older ones.
Today around 85 to 90% of wind turbines' total mass can be recycled.
"take" (disturb, injure or kill).
an SEL limit of 160 dB re 1 μPa2 s outside a 750-meter radius for pile-driving operations appears in the licence conditions for offshore wind farms.