Waveguide (radio frequency)

Last updated
Collection of standard waveguide components. Waveguide collection.jpg
Collection of standard waveguide components.

In radio-frequency engineering and communications engineering, waveguide is a hollow metal pipe used to carry radio waves. [1] This type of waveguide is used as a transmission line mostly at microwave frequencies, for such purposes as connecting microwave transmitters and receivers to their antennas, in equipment such as microwave ovens, radar sets, satellite communications, and microwave radio links.

Contents

The electromagnetic waves in a (metal-pipe) waveguide may be imagined as travelling down the guide in a zig-zag path, being repeatedly reflected between opposite walls of the guide. For the particular case of rectangular waveguide, it is possible to base an exact analysis on this view. Propagation in a dielectric waveguide may be viewed in the same way, with the waves confined to the dielectric by total internal reflection at its surface. Some structures, such as non-radiative dielectric waveguides and the Goubau line, use both metal walls and dielectric surfaces to confine the wave.

Principle

Example of waveguides and a diplexer in an air traffic control radar Diplexer1.jpg
Example of waveguides and a diplexer in an air traffic control radar

Depending on the frequency, waveguides can be constructed from either conductive or dielectric materials. Generally, the lower the frequency to be passed the larger the waveguide is. For example, the natural waveguide the earth forms given by the dimensions between the conductive ionosphere and the ground as well as the circumference at the median altitude of the Earth is resonant at 7.83 Hz. This is known as Schumann resonance. On the other hand, waveguides used in extremely high frequency (EHF) communications can be less than a millimeter in width.

History

George C. Southworth who developed waveguides in the early 1930s, in front of mile-long experimental waveguide run at Bell Labs, Holmdel, New Jersey, used in his research George Southworth & waveguides.jpg
George C. Southworth who developed waveguides in the early 1930s, in front of mile-long experimental waveguide run at Bell Labs, Holmdel, New Jersey, used in his research
Southworth (at left) demonstrating waveguide at IRE meeting in 1938, showing 1.5 GHz microwaves passing through the 7.5 m flexible metal hose registering on a diode detector. Southworth demonstrating waveguide.jpg
Southworth (at left) demonstrating waveguide at IRE meeting in 1938, showing 1.5 GHz microwaves passing through the 7.5 m flexible metal hose registering on a diode detector.

During the 1890s theorists did the first analyses of electromagnetic waves in ducts. [3] Around 1893 J. J. Thomson derived the electromagnetic modes inside a cylindrical metal cavity. [3] In 1897 Lord Rayleigh did a definitive analysis of waveguides; he solved the boundary value problem of electromagnetic waves propagating through both conducting tubes and dielectric rods of arbitrary shape. [3] [4] [5] [6] He showed that the waves could travel without attenuation only in specific normal modes with either the electric field (TE modes) or magnetic field (TM modes), perpendicular to the direction of propagation. He also showed each mode had a cutoff frequency below which waves would not propagate. Since the cutoff wavelength for a given tube was of the same order as its width, it was clear that a hollow conducting tube could not carry radio wavelengths much larger than its diameter. In 1902 R. H. Weber observed that electromagnetic waves travel at a slower speed in tubes than in free space, and deduced the reason; that the waves travel in a "zigzag" path as they reflect from the walls. [3] [5] [7]

Prior to the 1920s, practical work on radio waves concentrated on the low frequency end of the radio spectrum, as these frequencies were better for long-range communication. [3] These were far below the frequencies that could propagate in even large waveguides, so there was little experimental work on waveguides during this period, although a few experiments were done. In a June 1, 1894 lecture, "The work of Hertz", before the Royal Society, Oliver Lodge demonstrated the transmission of 3 inch radio waves from a spark gap through a short cylindrical copper duct. [3] [8] In his pioneering 1894-1900 research on microwaves, Jagadish Chandra Bose used short lengths of pipe to conduct the waves, so some sources credit him with inventing the waveguide. [9] However, after this, the concept of radio waves being carried by a tube or duct passed out of engineering knowledge. [3]

During the 1920s the first continuous sources of high frequency radio waves were developed: the Barkhausen–Kurz tube, [10] the first oscillator which could produce power at UHF frequencies; and the split-anode magnetron which by the 1930s had generated radio waves at up to 10 GHz. [3] These made possible the first systematic research on microwaves in the 1930s. It was discovered that transmission lines used to carry lower frequency radio waves, parallel line and coaxial cable, had excessive power losses at microwave frequencies, creating a need for a new transmission method. [3] [10]

The waveguide was developed independently between 1932 and 1936 by George C. Southworth at Bell Telephone Laboratories [2] and Wilmer L. Barrow at the Massachusetts Institute of Technology, who worked without knowledge of one another. [3] [5] [6] [10] Southworth's interest was sparked during his 1920s doctoral work in which he measured the dielectric constant of water with a radio frequency Lecher line in a long tank of water. He found that if he removed the Lecher line, the tank of water still showed resonance peaks, indicating it was acting as a dielectric waveguide. [3] At Bell Labs in 1931 he resumed work in dielectric waveguides. By March 1932 he observed waves in water-filled copper pipes. Rayleigh's previous work had been forgotten, and Sergei A. Schelkunoff, a Bell Labs mathematician, did theoretical analyses of waveguides [3] [11] and rediscovered waveguide modes. In December 1933 it was realized that with a metal sheath the dielectric is superfluous and attention shifted to metal waveguides.

Barrow had become interested in high frequencies in 1930 studying under Arnold Sommerfeld in Germany. [3] At MIT beginning in 1932 he worked on high frequency antennas to generate narrow beams of radio waves to locate aircraft in fog. He invented a horn antenna and hit on the idea of using a hollow pipe as a feedline to feed radio waves to the antenna. [3] By March 1936 he had derived the propagation modes and cutoff frequency in a rectangular waveguide. [10] The source he was using had a large wavelength of 40 cm, so for his first successful waveguide experiments he used a 16-foot section of air duct, 18 inches in diameter. [3]

Barrow and Southworth became aware of each other's work a few weeks before both were scheduled to present papers on waveguides to a combined meeting of the American Physical Society and the Institute of Radio Engineers in May 1936. [3] [10] They amicably worked out credit sharing and patent division arrangements.

The development of centimeter radar during World War 2 and the first high power microwave tubes, the klystron (1938) and cavity magnetron (1940), resulted in the first widespread use of waveguide. [10] Standard waveguide "plumbing" components were manufactured, with flanges on the end which could be bolted together. After the war in the 1950s and 60s waveguides became common in commercial microwave systems, such as airport radar and microwave relay networks which were built to transmit telephone calls and television programs between cities.

Description

Rectangular hollow Waveguide Waveguide.svg
Rectangular hollow Waveguide
Flexible waveguide from a J-Band radar WaveguideJ-Band.png
Flexible waveguide from a J-Band radar
Typical waveguide application: antenna feed for military radar. Radar antenna feed waveguide.png
Typical waveguide application: antenna feed for military radar.

In the microwave region of the electromagnetic spectrum, a waveguide normally consists of a hollow metallic conductor. These waveguides can take the form of single conductors with or without a dielectric coating, e.g. the Goubau line and helical waveguides. Hollow waveguides must be one-half wavelength or more in diameter in order to support one or more transverse wave modes.

Waveguides may be filled with pressurized gas to inhibit arcing and prevent multipaction, allowing higher power transmission. Conversely, waveguides may be required to be evacuated as part of evacuated systems (e.g. electron beam systems).

A slotted waveguide is generally used for radar and other similar applications. The waveguide serves as a feed path, and each slot is a separate radiator, thus forming an antenna. This structure has the capability of generating a radiation pattern to launch an electromagnetic wave in a specific relatively narrow and controllable direction.

A closed waveguide is an electromagnetic waveguide (a) that is tubular, usually with a circular or rectangular cross section, (b) that has electrically conducting walls, (c) that may be hollow or filled with a dielectric material, (d) that can support a large number of discrete propagating modes, though only a few may be practical, (e) in which each discrete mode defines the propagation constant for that mode, (f) in which the field at any point is describable in terms of the supported modes, (g) in which there is no radiation field, and (h) in which discontinuities and bends may cause mode conversion but not radiation.[ citation needed ]

The dimensions of a hollow metallic waveguide determine which wavelengths it can support, and in which modes. Typically the waveguide is operated so that only a single mode is present. The lowest order mode possible is generally selected. Frequencies below the guide's cutoff frequency will not propagate. It is possible to operate waveguides at higher order modes, or with multiple modes present, but this is usually impractical.

Waveguides are almost exclusively made of metal and mostly rigid structures. There are certain types of "corrugated" waveguides that have the ability to flex and bend but only used where essential since they degrade propagation properties. Due to propagation of energy in mostly air or space within the waveguide, it is one of the lowest loss transmission line types and highly preferred for high frequency applications where most other types of transmission structures introduce large losses. Due to the skin effect at high frequencies, electric current along the walls penetrates typically only a few micrometers into the metal of the inner surface. Since this is where most of the resistive loss occurs, it is important that the conductivity of interior surface be kept as high as possible. For this reason, most waveguide interior surfaces are plated with copper, silver, or gold.

Voltage standing wave ratio (VSWR) measurements may be taken to ensure that a waveguide is contiguous and has no leaks or sharp bends. If such bends or holes in the waveguide surface are present, this may diminish the performance of both transmitter and receiver equipment connected at either end. Poor transmission through the waveguide may also occur as a result of moisture build up which corrodes and degrades conductivity of the inner surfaces, which is crucial for low loss propagation. For this reason, waveguides are nominally fitted with microwave windows at the outer end that will not interfere with propagation but keep the elements out. Moisture can also cause fungus build up or arcing in high power systems such as radio or radar transmitters. Moisture in waveguides can typically be prevented with silica gel, a desiccant, or slight pressurization of the waveguide cavities with dry nitrogen or argon. Desiccant silica gel canisters may be attached with screw-on nibs and higher power systems will have pressurized tanks for maintaining pressure including leakage monitors. Arcing may also occur if there is a hole, tear or bump in the conducting walls, if transmitting at high power (usually 200 watts or more). Waveguide plumbing [12] is crucial for proper waveguide performance. Voltage standing waves occur when impedance mismatches in the waveguide cause energy to reflect back in the opposite direction of propagation. In addition to limiting the effective transfer of energy, these reflections can cause higher voltages in the waveguide and damage equipment.

Waveguide17-with-UBR120-flanges.svg
Short length of rectangular waveguide (WG17 with UBR120 connection-flanges)
J M Briscoe24 07 200713 14 56IMG2128 WAVEGUIDE.JPG
Section of the flexible waveguide
Waveguide900MHz.jpg
Waveguide (ankle piece 900MHz)

In practice

In practice, waveguides act as the equivalent of cables for super high frequency (SHF) systems. For such applications, it is desired to operate waveguides with only one mode propagating through the waveguide. With rectangular waveguides, it is possible to design the waveguide such that the frequency band over which only one mode propagates is as high as 2:1 (i.e. the ratio of the upper band edge to lower band edge is two). The relation between the waveguide dimensions and the lowest frequency is simple: if is the greater of its two dimensions, then the longest wavelength that will propagate is and the lowest frequency is thus

With circular waveguides, the highest possible bandwidth allowing only a single mode to propagate is only 1.3601:1. [13]

Because rectangular waveguides have a much larger bandwidth over which only a single mode can propagate, standards exist for rectangular waveguides, but not for circular waveguides. In general (but not always), standard waveguides are designed such that

The first condition is to allow for applications near band edges. The second condition limits dispersion, a phenomenon in which the velocity of propagation is a function of frequency. It also limits the loss per unit length. The third condition is to avoid evanescent-wave coupling via higher order modes. The fourth condition is that which allows a 2:1 operation bandwidth. Although it is possible to have a 2:1 operating bandwidth when the height is less than half the width, having the height exactly half the width maximizes the power that can propagate inside the waveguide before dielectric breakdown occurs.

Below is a table of standard waveguides. The waveguide name WR stands for waveguide rectangular, and the number is the inner dimension width of the waveguide in hundredths of an inch (0.01 inch = 0.254 mm) rounded to the nearest hundredth of an inch.

Standard sizes of rectangular waveguide
Waveguide nameFrequency
band name
Recommended
frequency band
of operation (GHz)
Cutoff frequency (GHz) ofInner dimensions of waveguide opening
lowest order modenext mode
EIA RCSC * IEC (inch)(mm)
WR2300WG0.0R30.32 — 0.450.2570.51323.000 × 11.500584.20 × 292.10
WR2100WG0R40.35 — 0.500.2810.56221.000 × 10.500533.40 × 266.7
WR1800WG1R50.45 — 0.630.3280.65618.000 × 9.000457.20 × 228.6
WR1500WG2R60.50 — 0.750.3930.78715.000 × 7.500381.00 × 190.5
WR1150WG3R80.63 — 0.970.5131.02611.500 × 5.750292.10 × 146.5
WR975WG4R90.75 — 1.150.6051.2119.750 × 4.875247.7 × 123.8
WR770WG5R120.97 — 1.450.7661.5337.700 × 3.850195,6 × 97.79
WR650WG6R14 L band (part)1.15 — 1.720.9081.8166.500 × 3.250165.1 × 82.55
WR510WG7R181.45 — 2.201.1572.3145.100 × 2.550129.5 × 64.77
WR430WG8R221.72 — 2.601.3722.7454.300 × 2.150109.2 × 54.61
WR340WG9AR26 S band (part)2.20 — 3.301.7363.4713.400 × 1.70086.36 × 43.18
WR284WG10R32 S band (part)2.60 — 3.952.0784.1562.840 × 1.340 72.14 × 34.94
WR229WG11AR40 C band (part)3.30 — 4.902.5775.1542.290 × 1.14558.17 × 29.08
WR187WG12R48 C band (part)3.95 — 5.853.1536.3051.872 × 0.872 47.55 × 22.2
WR159WG13R58 C band (part)4.90 — 7.053.7127.4231.590 × 0.79540.38 × 20.2
WR137WG14R70 C band (part)5.85 — 8.204.3018.6031.372 × 0.622 34.90 × 15.8
WR112WG15R847.05 — 10.05.26010.5201.122 × 0.497 28.50 × 12.6
WR90WG16R100 X band 8.2 — 12.46.55713.1140.900 × 0.400 22.9 × 10.2
WR75WG17R12010.0 — 15.07.86915.7370.750 × 0.37519.1 × 9.53
WR62WG18R140 Ku band 12.4 — 18.09.48818.9760.622 × 0.31115.8 × 7.90
WR51WG19R18015 — 2211.57223.1430.510 × 0.25513.0 × 6.48
WR42WG20R220 K band 18 — 26.514.05128.1020.420 × 0.170 10.7 × 4.32
WR34WG21R26022 — 3317.35734.7150.340 × 0.1708.64 × 4.32
WR28WG22R320 Ka band 26.5 — 4021.07742.1540.280 × 0.1407.11 × 3.56
WR22WG23R400 Q band 33 — 5026.34652.6920.224 × 0.1125.68 × 2.84
WR19WG24R500 U band 40 — 6031.39162.7820.188 × 0.0944.78 × 2.39
WR15WG25R620 V band 50 — 7539.87579.7500.148 × 0.0743.76 × 1.88
WR12WG26R740 E band 60 — 9048.37396.7460.122 × 0.0613.10 × 1.55
WR10WG27R900 W band 75 — 11059.015118.0300.100 × 0.0502.54 × 1.27
WR8WG28R1200 F band 90 — 14073.768147.5360.080 × 0.0402.03 × 1.02
WR6
WR7
WR6.5
WG29R1400 D band 110 — 17090.791181.5830.0650 × 0.03251.65 × 0.826
WR5WG30R1800 G band 140 — 220115.714231.4290.0510 × 0.02551.30 × 0.648
WR4WG31R2200170 — 260137.243274.4850.0430 × 0.02151.09 × 0.546
WR3WG32R2600220 — 330173.571347.1430.0340 × 0.01700.864 × 0.432
WR2.8260 — 400211.121422.2430.02795 × 0.013980.71 × 0.355
WR2.2325 — 500262.975525.9510.02244 × 0.011220.57 × 0.285
WR1.9400 — 600318.928637.8560.01850 × 0.0092520.47 × 0.235
WR1.5500 — 750394.463788.9270.01496 × 0.0074800.38 × 0.19
WR1.2600 — 900483.536967.0720.01220 × 0.0061020.31 × 0.155
WR1750 — 1100599.5841199.20.009843 × 0.0049210.25 × 0.125
* Radio Components Standardization Committee
For historical reasons the outside rather than the inside dimensions of these waveguides are 2:1 (with wall thickness WG6–WG10: 0.08" (2.0 mm), WG11A–WG15: 0.064" (1.6 mm), WG16–WG17: 0.05" (1.3 mm), WG18–WG28: 0.04" (1.0 mm)) [15]

For the frequencies in the table above, the main advantage of waveguides over coaxial cables is that waveguides support propagation with lower loss. For lower frequencies, the waveguide dimensions become impractically large, and for higher frequencies the dimensions become impractically small (the manufacturing tolerance becomes a significant portion of the waveguide size).

Mathematical analysis

Electromagnetic waveguides are analyzed by solving Maxwell's equations, or their reduced form, the electromagnetic wave equation, with boundary conditions determined by the properties of the materials and their interfaces. These equations have multiple solutions, or modes, which are eigenfunctions of the equation system. Each mode is characterized by a cutoff frequency below which the mode cannot exist in the guide. Waveguide propagation modes depend on the operating wavelength and polarization and the shape and size of the guide. The longitudinal mode of a waveguide is a particular standing wave pattern formed by waves confined in the cavity. The transverse modes are classified into different types:

Waveguides with certain symmetries may be solved using the method of separation of variables. Rectangular wave guides may be solved in rectangular coordinates. [16] :143 Round waveguides may be solved in cylindrical coordinates. [16] :198

In hollow, single conductor waveguides, TEM waves are not possible. This contrasts with two-conductor transmission lines used at lower frequencies; coaxial cable, parallel wire line and stripline, in which TEM mode is possible. Additionally, the propagating modes (i.e. TE and TM) inside the waveguide can be mathematically expressed as the superposition of two TEM waves. [17]

The mode with the lowest cutoff frequency is termed the dominant mode of the guide. It is common to choose the size of the guide such that only this one mode can exist in the frequency band of operation. In rectangular and circular (hollow pipe) waveguides, the dominant modes are designated the TE1,0 mode and TE1,1 modes respectively. [18]

Dielectric waveguides

A dielectric waveguide employs a solid dielectric rod rather than a hollow pipe. An optical fibre is a dielectric guide designed to work at optical frequencies. Transmission lines such as microstrip, coplanar waveguide, stripline or coaxial cable may also be considered to be waveguides.

Dielectric rod and slab waveguides are used to conduct radio waves, mostly at millimeter wave frequencies and above. [19] [20] These confine the radio waves by total internal reflection from the step in refractive index due to the change in dielectric constant at the material surface. [21] At millimeter wave frequencies and above, metal is not a good conductor, so metal waveguides can have increasing attenuation. At these wavelengths dielectric waveguides can have lower losses than metal waveguides. Optical fibre is a form of dielectric waveguide used at optical wavelengths.

One difference between dielectric and metal waveguides is that at a metal surface the electromagnetic waves are tightly confined; at high frequencies the electric and magnetic fields penetrate a very short distance into the metal. In contrast, the surface of the dielectric waveguide is an interface between two dielectrics, so the fields of the wave penetrate outside the dielectric in the form of an evanescent (non-propagating) wave. [21]

See also

Related Research Articles

<span class="mw-page-title-main">Microwave</span> Electromagnetic radiation with wavelengths from 1 m to 1 mm

Microwave is a form of electromagnetic radiation with wavelengths ranging from about 30 centimeters to one millimeter corresponding to frequencies between 1 GHz and 300 GHz respectively. Different sources define different frequency ranges as microwaves; the above broad definition includes UHF, SHF and EHF bands. A more common definition in radio-frequency engineering is the range between 1 and 100 GHz. In all cases, microwaves include the entire SHF band at minimum. Frequencies in the microwave range are often referred to by their IEEE radar band designations: S, C, X, Ku, K, or Ka band, or by similar NATO or EU designations.

<span class="mw-page-title-main">Cutoff frequency</span> Frequency response boundary

In physics and electrical engineering, a cutoff frequency, corner frequency, or break frequency is a boundary in a system's frequency response at which energy flowing through the system begins to be reduced rather than passing through.

<span class="mw-page-title-main">Surface wave</span> Physical phenomenon

In physics, a surface wave is a mechanical wave that propagates along the interface between differing media. A common example is gravity waves along the surface of liquids, such as ocean waves. Gravity waves can also occur within liquids, at the interface between two fluids with different densities. Elastic surface waves can travel along the surface of solids, such as Rayleigh or Love waves. Electromagnetic waves can also propagate as "surface waves" in that they can be guided along with a refractive index gradient or along an interface between two media having different dielectric constants. In radio transmission, a ground wave is a guided wave that propagates close to the surface of the Earth.

<span class="mw-page-title-main">Transmission medium</span> Conduit for signal propagation

A transmission medium is a system or substance that can mediate the propagation of signals for the purposes of telecommunication. Signals are typically imposed on a wave of some kind suitable for the chosen medium. For example, data can modulate sound, and a transmission medium for sounds may be air, but solids and liquids may also act as the transmission medium. Vacuum or air constitutes a good transmission medium for electromagnetic waves such as light and radio waves. While a material substance is not required for electromagnetic waves to propagate, such waves are usually affected by the transmission media they pass through, for instance, by absorption or reflection or refraction at the interfaces between media. Technical devices can therefore be employed to transmit or guide waves. Thus, an optical fiber or a copper cable is used as transmission media.

<span class="mw-page-title-main">Waveguide</span> Structure that guides waves efficiently

A waveguide is a structure that guides waves by restricting the transmission of energy to one direction. Common types of waveguides include acoustic waveguides which direct sound, optical waveguides which direct light, and radio-frequency waveguides which direct electromagnetic waves other than light like radio waves.

<span class="mw-page-title-main">Coaxial cable</span> Electrical cable type with concentric inner conductor, insulator, and conducting shield

Coaxial cable, or coax, is a type of electrical cable consisting of an inner conductor surrounded by a concentric conducting shield, with the two separated by a dielectric ; many coaxial cables also have a protective outer sheath or jacket. The term coaxial refers to the inner conductor and the outer shield sharing a geometric axis.

<span class="mw-page-title-main">Radio wave</span> Type of electromagnetic radiation

Radio waves are a type of electromagnetic radiation with the longest wavelengths in the electromagnetic spectrum, typically with frequencies of 300 gigahertz (GHz) and below. At 300 GHz, the corresponding wavelength is 1mm, which is shorter than the diameter of a grain of rice. At 30 Hz the corresponding wavelength is ~10,000 kilometers, which is longer than the radius of the Earth. Wavelength of a radio wave is inversely proportional to its frequency, because its velocity is constant. Like all electromagnetic waves, radio waves in a vacuum travel at the speed of light, and in the Earth's atmosphere at a slightly slower speed. Radio waves are generated by charged particles undergoing acceleration, such as time-varying electric currents. Naturally occurring radio waves are emitted by lightning and astronomical objects, and are part of the blackbody radiation emitted by all warm objects.

This is an index of articles relating to electronics and electricity or natural electricity and things that run on electricity and things that use or conduct electricity.

<span class="mw-page-title-main">Resonator</span> Device or system that exhibits resonance

A resonator is a device or system that exhibits resonance or resonant behavior. That is, it naturally oscillates with greater amplitude at some frequencies, called resonant frequencies, than at other frequencies. The oscillations in a resonator can be either electromagnetic or mechanical. Resonators are used to either generate waves of specific frequencies or to select specific frequencies from a signal. Musical instruments use acoustic resonators that produce sound waves of specific tones. Another example is quartz crystals used in electronic devices such as radio transmitters and quartz watches to produce oscillations of very precise frequency.

<span class="mw-page-title-main">Horn antenna</span> Funnel-shaped waveguide radio device

A horn antenna or microwave horn is an antenna that consists of a flaring metal waveguide shaped like a horn to direct radio waves in a beam. Horns are widely used as antennas at UHF and microwave frequencies, above 300 MHz. They are used as feed antennas for larger antenna structures such as parabolic antennas, as standard calibration antennas to measure the gain of other antennas, and as directive antennas for such devices as radar guns, automatic door openers, and microwave radiometers. Their advantages are moderate directivity, broad bandwidth, low losses, and simple construction and adjustment.

<span class="mw-page-title-main">Goubau line</span> Single wire transmission line used to conduct radio waves at UHF and microwave frequencies

A Goubau line or Sommerfeld–Goubau line, or G-line for short, is a single-wire transmission line used to conduct radio waves at UHF and microwave frequencies. The dielectric coated transmission line was invented by F. Harms in 1907 and George J. E. Goubau in 1950, based on work on surface waves on wires from 1899 by Arnold Sommerfeld. It is used as a feedline at UHF to link high frequency transmitters and receivers to their antennas, and in scientific research.

An optical waveguide is a physical structure that guides electromagnetic waves in the optical spectrum. Common types of optical waveguides include optical fiber waveguides, transparent dielectric waveguides made of plastic and glass, liquid light guides, and liquid waveguides.

A dielectric resonator antenna (DRA) is a radio antenna mostly used at microwave frequencies and higher, that consists of a block of ceramic material of various shapes, the dielectric resonator, mounted on a metal surface, a ground plane. Radio waves are introduced into the inside of the resonator material from the transmitter circuit and bounce back and forth between the resonator walls, forming standing waves. The walls of the resonator are partially transparent to radio waves, allowing the radio power to radiate into space.

<span class="mw-page-title-main">Metamaterial antenna</span>

Metamaterial antennas are a class of antennas which use metamaterials to increase performance of miniaturized antenna systems. Their purpose, as with any electromagnetic antenna, is to launch energy into free space. However, this class of antenna incorporates metamaterials, which are materials engineered with novel, often microscopic, structures to produce unusual physical properties. Antenna designs incorporating metamaterials can step-up the antenna's radiated power.

<span class="mw-page-title-main">Tunable metamaterial</span>

A tunable metamaterial is a metamaterial with a variable response to an incident electromagnetic wave. This includes remotely controlling how an incident electromagnetic wave interacts with a metamaterial. This translates into the capability to determine whether the EM wave is transmitted, reflected, or absorbed. In general, the lattice structure of the tunable metamaterial is adjustable in real time, making it possible to reconfigure a metamaterial device during operation. It encompasses developments beyond the bandwidth limitations in left-handed materials by constructing various types of metamaterials. The ongoing research in this domain includes electromagnetic materials that are very meta which mean good and has a band gap metamaterials (EBG), also known as photonic band gap (PBG), and negative refractive index material (NIM).

<span class="mw-page-title-main">Waveguide filter</span> Electronic filter that is constructed with waveguide technology

A waveguide filter is an electronic filter constructed with waveguide technology. Waveguides are hollow metal conduits inside which an electromagnetic wave may be transmitted. Filters are devices used to allow signals at some frequencies to pass, while others are rejected. Filters are a basic component of electronic engineering designs and have numerous applications. These include selection of signals and limitation of noise. Waveguide filters are most useful in the microwave band of frequencies, where they are a convenient size and have low loss. Examples of microwave filter use are found in satellite communications, telephone networks, and television broadcasting.

<span class="mw-page-title-main">Substrate-integrated waveguide</span> Waveguide formed by posts inserted in a dielectric substrate

A substrate-integrated waveguide (SIW) is a synthetic rectangular electromagnetic waveguide formed in a dielectric substrate by densely arraying metallized posts or via holes that connect the upper and lower metal plates of the substrate. The waveguide can be easily fabricated with low-cost mass-production using through-hole techniques, where the post walls consists of via fences. SIW is known to have similar guided wave and mode characteristics to conventional rectangular waveguide with equivalent guide wavelength.

Leaky-wave antenna (LWA) belong to the more general class of traveling wave antenna, that use a traveling wave on a guiding structure as the main radiating mechanism. Traveling-wave antenna fall into two general categories, slow-wave antennas and fast-wave antennas, which are usually referred to as leaky-wave antennas.

<span class="mw-page-title-main">Planar transmission line</span> Transmission lines with flat ribbon-like conducting or dielectric lines

Planar transmission lines are transmission lines with conductors, or in some cases dielectric (insulating) strips, that are flat, ribbon-shaped lines. They are used to interconnect components on printed circuits and integrated circuits working at microwave frequencies because the planar type fits in well with the manufacturing methods for these components. Transmission lines are more than simply interconnections. With simple interconnections, the propagation of the electromagnetic wave along the wire is fast enough to be considered instantaneous, and the voltages at each end of the wire can be considered identical. If the wire is longer than a large fraction of a wavelength, these assumptions are no longer true and transmission line theory must be used instead. With transmission lines, the geometry of the line is precisely controlled so that its electrical behaviour is highly predictable. At lower frequencies, these considerations are only necessary for the cables connecting different pieces of equipment, but at microwave frequencies the distance at which transmission line theory becomes necessary is measured in millimetres. Hence, transmission lines are needed within circuits.

<span class="mw-page-title-main">Lens antenna</span> Microwave antenna

A lens antenna is a directional antenna that uses a shaped piece of microwave-transparent material to bend and focus microwaves by refraction, as an optical lens does for light. Typically it consists of a small feed antenna such as a patch antenna or horn antenna which radiates radio waves, with a piece of dielectric or composite material in front which functions as a converging lens to collimate the radio waves into a beam. Conversely, in a receiving antenna the lens focuses the incoming radio waves onto the feed antenna, which converts them to electric currents which are delivered to a radio receiver. They can also be fed by an array of feed antennas, called a focal plane array (FPA), to create more complicated radiation patterns.

References

  1. Radatz, Jane. The IEEE Standard Dictionary of Electrical and Electronics Terms (6 ed.). IEEE Standards Association. ISBN   1559378336.
  2. 1 2 3 Southworth, G. C. (August 1936). "Electric Wave Guides" (PDF). Short Wave Craft. 7 (1): 198, 233. Retrieved March 27, 2015.
  3. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Packard, Karle S. (September 1984). "The Origin of Waveguides: A Case of Multiple Rediscovery" (PDF). IEEE Transactions on Microwave Theory and Techniques. MTT-32 (9): 961–969. Bibcode:1984ITMTT..32..961P. CiteSeerX   10.1.1.532.8921 . doi:10.1109/tmtt.1984.1132809 . Retrieved March 24, 2015.
  4. Strutt, William (Lord Rayleigh) (February 1897). "On the passage of electric waves through tubes, or the vibrations of dielectric cylinders". Philosophical Magazine. 43 (261): 125–132. doi:10.1080/14786449708620969.
  5. 1 2 3 Kizer, George (2013). Digital Microwave Communication: Engineering Point-to-Point Microwave Systems. John Wiley and Sons. p. 7. ISBN   978-1118636800.
  6. 1 2 Lee, Thomas H. (2004). Planar Microwave Engineering: A Practical Guide to Theory, Measurement, and Circuits, Vol. 1. Cambridge University Press. pp. 18, 118. ISBN   9780521835268.
  7. Weber, R. H. (1902). "Elektromagnetische Schwingungen in Metallrohren". Annalen der Physik. 8 (4): 721–751. Bibcode:1902AnP...313..721W. doi:10.1002/andp.19023130802. hdl: 2027/uc1.$b24304 .
  8. Lodge, Oliver (June 1, 1984). "The Work of Hertz". Proc. Of the Royal Institution. 14 (88): 331–332. Retrieved April 11, 2015.
  9. Emerson, Darrel T. (1998). "Jagadish Chandra Bose: Millimeter-wave research in the 19th century" (PDF). US National Radio Astronomy Observatory. Retrieved April 11, 2015.
  10. 1 2 3 4 5 6 Brown, Louis (1999). Technical and Military Imperatives: A Radar History of World War 2. CRC Press. pp. 146–148. ISBN   978-1420050660.
  11. Schelkunoff, Sergei A. (November 1937). "Electromagnetic Waves in Conducting Tubes". Physical Review. 52 (10): 1078. Bibcode:1937PhRv...52.1078S. doi:10.1103/PhysRev.52.1078.
  12. "Module 12: Waveguide Plumbing". Introduction to Waveguides. Plasma and Beam Physics Research Facility, Dept. of Physics and Materials Science, Chiang Mai University, Thailand. 2012. Retrieved September 21, 2015.
  13. For bandwidths lower than 2:1 it is more common to express them as a percentage of the center frequency, which in the case of 1.360:1 is 26.55 %. For reference, a 2:1 bandwidth corresponds to a 66.67 % bandwidth. The reason for expressing bandwidths as a ratio of upper to lower band edges for bandwidths greater than 66.67 % is that in the limiting case that the lower edge goes to zero (or the upper edge goes to infinity), the bandwidth approaches 200 %, which means that the entire range of 3:1 to infinity:1 map into the range 100 % to 200 %.
  14. Harvey, A. F. (July 1955). "Standard waveguides and couplings for microwave equipment". Proceedings of the IEE - Part B: Radio and Electronic Engineering. 102 (4): 493–499. doi:10.1049/pi-b-1.1955.0095.
  15. Baden Fuller, A. J. (1969). Microwaves (1 ed.). Pergamon Press. ISBN   978-0-08-006616-5.
  16. 1 2 Harrington, Roger F. (1961), Time-Harmonic Electromagnetic Fields, McGraw-Hill, pp. 7–8, hdl: 2027/mdp.39015002091489 , ISBN   0-07-026745-6
  17. Someda, Carlo G. (1998). Electromagnetic Waves. CRC Press. pp. 257–258. ISBN   0412578700..
  18. Modi, Anuj Y.; Balanis, Constantine A. (2016). "PEC-PMC Baffle Inside Circular Cross Section Waveguide for Reduction of Cut-Off Frequency". IEEE Microwave and Wireless Components Letters. 26 (3): 171–173. doi:10.1109/LMWC.2016.2524529. S2CID   9594124.
  19. Lioubtchenko, Dmitri; Sergei Tretyakov; Sergey Dudorov (2003). Millimeter-Wave Waveguides. Springer. p. 149. ISBN   978-1402075315.
  20. Shevgaonkar, R. K. (2005). Electromagnetic Waves. Tata McGraw-Hill Education. p. 327. ISBN   978-0070591165.
  21. 1 2 Rana, Farhan (Fall 2005). "Lecture 26: Dielectric slab waveguides" (PDF). Class notes ECE 303: Electromagnetic Fields and Waves. Electrical Engineering Dept. Cornell Univ. pp. 2–3, 10. Retrieved June 21, 2013.

Further reading