P-63 Kingcobra | |
---|---|
Role | Fighter aircraft |
National origin | United States |
Manufacturer | Bell Aircraft |
First flight | 7 December 1942 |
Introduction | October 1943 |
Status | Retired |
Primary users | United States Army Air Forces Soviet Air Force French Air Force |
Produced | 1943–1945 |
Number built | 3,303 |
Developed from | Bell P-39 Airacobra |
Variants | Bell L-39 |
The Bell P-63 Kingcobra is an American fighter aircraft that was developed by Bell Aircraft during World War II. Based on the preceding Bell P-39 Airacobra, the P-63's design incorporated suggestions from P-39 pilots and was superior to its predecessor in virtually all respects. The P-63 was not accepted for combat use by the United States Army Air Forces. However, it was used during World War II by the Soviet Air Force, [1] which had also been the most prolific user of the P-39.
While the P-39 had been introduced as an interceptor, later in its development it was decided to reduce the cost and complexity of the engine by removing the turbocharger. High-altitude performance suffered dramatically as a result, and Bell proposed an experimental series to test out a variety of solutions.
The resulting XP-39E featured two primary changes from the earlier P-39D from which it was developed. One was a redesigned wing. The root airfoil, a NACA 0015 on other models of the P-39, was changed to a NACA 0018, to gain internal volume. [2] The other was a switch to the Continental I-1430 engine, which featured an improved overall design developed from the hyper engine efforts, as well as an improved supercharger.
Three prototypes were ordered in April 1941 with serials 41-19501, 41-19502 and 42-7164. The I-1430 had continued development problems and could not be delivered in time, so it was replaced by an Allison V-1710-47, similar to that powering the P-39. Each prototype tested different wing and tail configurations: 41-19501 had a rounded vertical tail, but squared-off tailplane tips; 41-19502, a squared-off fin and rudder and large wing fillets; and 42-7164 had all its flight surfaces squared off. The XP-39E proved faster than standard Airacobra, reaching a maximum speed of 386 mph (621 km/h) at 21,680 ft (6,610 m) during tests. However, the XP-39E was considered inferior to the stock P-39 Airacobra in all other respects, so it was not ordered into production.
Although the XP-39E proved disappointing, the USAAF was nevertheless interested in an even larger aircraft based on the same basic layout. Even before its first flight, the USAAF placed an order on 27 June 1941 for two prototypes of an enlarged version powered by the same V-1710-47. The new design was given the designation XP-63 and serials were 41-19511 and 41-19512. A third prototype was also ordered, 42-78015, using the Packard V-1650, the U.S.-built version of the Rolls-Royce Merlin engine.
The XP-63 was larger in all dimensions than the Airacobra. The wing was redesigned again, this time with new NACA laminar flow airfoils, 66(215)-116 a=0.6 at the root and a NACA 66(215)-216 a=0.6 at the tip. The wing taper ratio was approximately 2:1, span was 38 ft 4 in (11.68 m), and wing area was 248 sq ft (23.0 m2). [3] The engine was fitted with a second remotely mounted supercharger, supplementing the normal single-stage supercharger. At higher altitudes, when additional boost was required, a hydraulic clutch would engage the second supercharger, adding 10,000 ft (3,000 m) to the service ceiling. A larger four-bladed propeller was also standardized. A persistent complaint about the Airacobra was that its nose armament was not easily accessible for ground maintenance; to cure this problem the XP-63 airframe was fitted with larger cowling panels.
In September 1942, even before the prototype flew, the USAAF ordered it into production as the P-63A (Model 33). [4] The P-63A's armament was to be the same as the current P-39Q, a single 37 mm (1.46 in) M4 cannon firing through the propeller hub, two synchronized .50 in (12.7 mm) machine guns in the cowl, and two .50 in (12.7 mm) machine guns in underwing gondolas.
The first prototype, 41-19511, flew for the first time on 7 December 1942. It was destroyed on 28 January 1943 when its landing gear failed to extend. The second prototype, 41-19512, followed on 5 February 1943. It, too, was destroyed, this time due to an engine failure. The Merlin-engined 42-78015 (as Merlins were primarily needed for the P-51 Mustang) was delivered with another Allison instead, a -93, which had a war emergency rating of 1,500 hp (1,100 kW) at sea level, making this prototype one of the fastest Kingcobras built, attaining 421 mph (678 km/h) at 24,100 ft (7,300 m).
Deliveries of production P-63As began in October 1943. The USAAF concluded the Kingcobra was inferior to the Mustang, and declined to order larger quantities. American allies, particularly the Soviet Union, had a great need for fighter aircraft, however, and the Soviets were already the largest users of the Airacobra. Therefore, the Kingcobra was ordered into production to be delivered under Lend-Lease. In February 1944, the Soviet government sent a highly experienced test pilot, Andrey G. Kochetkov, and an aviation engineer, Fyodor P. Suprun, to the Bell factories to participate in the development of the first production variant, the P-63A. Initially ignored by Bell engineers, Kochetkov's expert testing of the machine's spin characteristics (which led to airframe buckling) eventually led to a significant Soviet role in the development. After flat spin recovery proved impossible, and upon Kochetkov's making a final recommendation that pilots should bail out upon entering such a spin, he received a commendation from the Irving Parachute Company. The Kingcobra's maximum aft CG was moved forward to facilitate recovery from spins. [5]
P-63A-8, SN 269261, was extensively tested at TsAGI in what was then the world's largest wind tunnel. Soviet input was significant. With the Soviet Union being the largest buyer of the aircraft, Bell was quick to implement their suggestions. Most of the changes in the A sub-variants were a direct result of Soviet input, e.g. increased pilot armor and fuselage hardpoint on the A-5, underwing hardpoints and extra fuel tanks on the A-6, etc. The Soviet Union even experimented with ski landing gear for the P-63A-6, but this never reached production. Most significantly, Soviet input resulted in moving the main cannon forward, favorably changing the center of gravity, and increasing its ammunition load from 30 to 58 rounds for the A-9 variant. The P-63 had an impressive roll rate, besting the US P-47, P-40, and P-51—and the Japanese Navy's Kawanishi N1K2 Shiden-Kai fighter—with a rate of 110° per second at 275 mph (443 km/h). [6]
After the war, two war surplus P-63Cs were modified by Bell under Navy contract for flight testing of low-speed and stall characteristics of high-speed wing designs. The aircraft received new wings with adjustable leading edge slats, trailing edge flaps and a pronounced sweep of 35 degrees. The wings had no wheel wells; only the nose gear was retractable. [7] L-39-1 first flew 23 April 1946, demonstrating a need for extra tail surface and rear fuselage length to balance the aircraft in flight—the wing repositioning reduced empennage effectiveness and moved the center of lift aft. A lighter three-bladed propeller from a P-39Q-10 was mounted and the necessary changes to the empennage were made. L-39-2 incorporated these adjustments from the start. L-39-1 later went to NACA at Langley for wind tunnel testing, where much valuable data was gathered. [8] L-39-2 also served as a testbed for the Bell X-2 40-degree wing design. [9]
This article includes a list of general references, but it lacks sufficient corresponding inline citations .(June 2013) |
The first version to be supplied in quantity to the Soviet Union was the P-63A-7 with a higher vertical tail, and reinforced wings and fuselage. The fuselage proved to need strengthening; consequently, in October 1944 a reinforcement kit for operational P-63s was developed. [10]
Air Transport Command ferry pilots, including U.S. women pilots of the WASP program, picked up the planes at the Bell factory at Niagara Falls, New York, and flew them to Great Falls, Montana and then onward via the Northwest Staging Route through Canada to Alaska, where Soviet ferry pilots, many of them also women, would take delivery of the aircraft at Nome [11] and fly them to the Soviet Union over the Bering Strait via the Alaska-Siberia route (ALSIB). A total of 2,397 (2,672, according to other sources) [12] aircraft were delivered to the USSR, 72.6% of the overall 3,303 production aircraft. [13]
By a 1943 agreement, P-63s were not allowed for Soviet use against Germany and were supposed to be concentrated in the Soviet Far East for an eventual attack on Japan.[ citation needed ] However, there are many unconfirmed reports from both Soviet and German sources that P-63s did indeed see service against the Luftwaffe . In memoirs published in the 1990s, one of Pokryshkin's pilots reported that the entire 4th Guards Fighter Aviation Regiment (4 GvIAP) was secretly converted to P-63s in 1944, while officially still flying P-39s. One account states they were in action at Königsberg, in Poland and in the final assault on Berlin. There are German reports of P-63s shot down by both fighters and flak. Hans Rudel, the most-decorated pilot of the Luftwaffe, states in his memoirs, "We often encounter American types of aircraft, especially Airacobras, Kingcobras and Bostons." This was in the Courland front towards the end of the war. [14] Nevertheless, all Soviet records show nothing but P-39s used against Germany.[ citation needed ]
In general, official Soviet histories played down the role of Lend-Lease supplied aircraft in favor of local designs, but it is known that the P-63 was a successful fighter aircraft in Soviet service. A common Western misconception is that the Bell fighters were used as ground attack aircraft.
One of the enduring myths regarding the P-39/P-63 in Soviet use is that because of its armament, in particular the 37mm nose cannon, it excelled as a ground-attack aircraft, even a 'tank buster'. In translating and preparing this manuscript for publication, I have had the opportunity to peruse several Russian-language sources. Mentions of the employment of this aircraft in the ground-attack role are so rare in these sources as to be exceptional ... The 'tank buster' myth has its roots in the misunderstanding of the general wartime role of the Red Air Force and in the imprecise translation of specific Russian-Language terms that describe this role. The specific Russian-Language term most often used to describe the mission and role of the Airacobra-equipped Red Air Force fighter units, in this manuscript and other Russian-language sources, is prikrytiye sukhoputnykh voysk [coverage of ground forces]... Frequent misunderstanding in this country as to the combat role of the P-39 in Soviet use is based in part on imprecise translation of the term prikrytiye sukhoputnykh voysk to 'ground support'. The latter term as it is understood by many Western military historians and readers, suggests the attacking of ground targets in support of ground troops, also called 'close air support'. Did a Soviet Airacobra pilot ever strafe a German tank? Undoubtedly. But this was never a primary mission or strong suit for this aircraft.
— Soviet Army Colonel Dmitry Loza, Commanding the Red Army's Sherman Tanks: The World War II Memoirs of Hero of the Soviet Union, Dmitriy Loza, Loza and Gebhardt 2002, pp. 15–16.
The Soviets developed successful group aerial fighting tactics for the Bell fighters and scored a surprising number of aerial victories over a variety of German aircraft. Low ceilings, short missions, good radios, a sealed and warm cockpit and ruggedness contributed to their effectiveness. To pilots who had once flown the tricky Polikarpov I-16, the aerodynamic quirks of the mid-engined aircraft were unimportant. In the Far East, P-63 and P-39 aircraft were used in the Soviet invasion of Manchukuo and northern Korea. In the Pacific theatre, the Kingcobras flew escort, close air support and ground attack missions. The Soviet P-63s achieved their first air victory on 15 August 1945, when Lejtenant I. F. Miroshnichenko from 17th IAP/190 IAD, shot down a Nakajima Ki-43 Hayabusa IJAAS fighter off the coast of North Korea. [12]
Sufficient aircraft continued in use after the war for them to be given the NATO reporting name of Fred. By 9 May 1945, operational units still had 1,148 Kingcobras on strength. [12] On 8 October 1950, two USAF F-80Cs from the 49th Fighter Group breached the USSR's border and attacked Sukhaya Rechka airfield 19 mi (31 km) south-west of Vladivostok and 62 mi (100 km) from the Soviet-Korean border, [15] making two strafing runs before returning to their home base. Soviet sources say the attack was intentional, but the pilots claimed it was a result of a navigational error. [16] The airfield belonged to the Air Forces of the Pacific Fleet (VVS TOF), but it was occupied by the 821st Fighter Aviation Regiment (821 IAP) of the 190th Fighter Aviation Division (190 IAD). Mostly aircraft of the 1st Squadron of 821 IAP were hit with 12 P-63s damaged, one P-63 burned to the ground while the other damaged aircraft were able to be repaired. There were no human losses. [17]
This section needs expansion. You can help by adding to it. (June 2013) |
In 1945, 114 later models were delivered to the French Air Force (Armée de l'Air), but they arrived too late to see service in World War II. They did see service during the First Indochina War before being replaced in 1951.
Initially, the French Kingcobras were deployed to Algeria. Fighter squadron (Groupe de Chasse) 2/6 "Travail", previously equipped with P-39 Airacobras, received their Kingcobras on 18 July at Casablanca; the pilots were surprised by the higher landing speed of their new aircraft. [18] The Kingcobra were scrambled to Indochina when the insurgency broke. Only 60 Kingcobras were operational in Indochina in January 1950, mainly because the Americans refused to supply spare parts. [19] Starting in February 1951, the squadrons equipped with Kingcobra started to receive Grumman F8F Bearcats as replacements. Most Kingcobras were mothballed by July. The last flight of a Kingcobra in Indochina took place on 6 September 1951. [20]
Its main use in American service was the unusual one of a manned flying target for gunnery practice. [21] The aircraft was generally painted bright orange to increase its visibility. All armament and the regular armor was removed from these RP-63 aircraft, and over a ton of armored sheet metal was applied to the aircraft. This was fitted with sensors that would detect hits, and these hits were signaled by illuminating a light in the propeller hub where the cannon would have been. This earned the aircraft the unofficial nickname of Pinball. [21] Special frangible rounds made of a lead/Bakelite combination were developed that would disintegrate upon impact. [21] These were known as the "Cartridge, Caliber .30, Frangible, Ball, M22". In 1990, veteran Pinball pilot, Ivan L. Hickman, wrote Operation Pinball about the training flights. [22]
British engineers, like the Americans, had a growing interest during World War II in the application of laminar flow airfoils. In an effort to learn more about the practical application of laminar flow airfoils, in 1945 the Royal Aircraft Establishment (RAE) undertook a flight test program with one of the two P-63As that the United Kingdom had received. [23] [ page needed ] The aircraft was equipped with a wake rake array mounted outboard, behind the wing, to allow the momentum deficit, and thus section drag, to be measured.
The RAE first tested it in an "as delivered" configuration. The wing airfoil was designed to support laminar flow to 60% of chord. In the "as delivered" configuration, a profile drag was measured which was representative of the wing section with boundary layer transition at the leading edge (0% laminar flow). Reducing the surface roughness reduced the drag at low lift coefficients to a level representative of laminar flow to 35% of chord. [23] Measurements were made of the surface waviness. This showed peak wave amplitudes, above the mean, of approximately 0.011 inches (0.28 mm) over a two-inch (5.1 cm) span. The standard waviness criteria [24] shows the critical wave height to be 0.0053 inches (0.13 mm) for this application. [25] To reduce the waviness, RAE personnel stripped the wing to bare metal. The wing was then sprayed with two coats of primer paint and a coat of paint type filler. After the paint was dry, it was sanded in a chordwise direction, using sanding blocks whose curvature matched the local surface curvature. This was repeated several times. Surface waviness was then measured and found to be no more than 0.005 inches (0.13 mm). In flight, this configuration was found to have a profile drag representative of boundary layer transition at 60% of chord. [23] This gave researchers an idea of what level of wing surface quality was required to actually get the benefits of laminar flow airfoils.
Numerous surplus P-63s ended up on the air racing circuit in the immediate postwar era. Charles Tucker purchased two P-63s from the disposal facility at Kingman, Arizona just after the war. He entered one of them, the Tucker Special as Race 28 with the name Flying Red Horse emblazoned on the nose (civilian register N62995) in the 1946 Thompson Trophy race. He had clipped the wings by 12 ft 9 in (3.89 m) in an attempt to improve its speed, reducing the span to 25 ft 9 in (7.85 m). The second one (44-4126 (XN63231 Race 30)) was intended for the 1946 Bendix cross country race. It was initially fitted with two wingtip drop tanks. In 1947, the drop tanks were removed and the wings were clipped to 28 ft 6 in (8.69 m).
Two other significant racers were flown later. Tipsy Miss, John Sandberg's clipped-wingtip P-63 unlimited racer, was identified as "Race 28," and painted in bright orange, white and black race numbers with a chrome spinner. Later sold to a European pilot, this P-63 was destroyed in a fatal accident in 1990 [26] [27] Crazy Horse Campgrounds was the most radically modified P-63 Kingcobra ever. Larry Haven's "Race 90" clipped-wing unlimited racer had a tiny bubble canopy installed; it appeared in all silver (unpolished aluminum) finish with a white rudder and black trim. The aircraft later crashed into the ocean on a test flight in 1972. [28]
On 3 June 2001, a Bell P-63A crashed during the Biggin Hill International Air Fair in London, England, killing the pilot. The pilot was at the top of a vertical maneuver when he appeared to have lost control of the plane. This was the second plane accident in 24 hours at Biggin Hill following the crash of a de Havilland Vampire that killed both pilots. [48] [49] [50]
On 12 November 2022, P-63F 43-11719, owned by the Commemorative Air Force, collided with Boeing B-17G Flying Fortress Texas Raiders at an airshow in Dallas, Texas. 43-11719 was one of only five remaining airworthy P-63s and was one of the few P-63F variants ever built. [51] Six people were killed, one in the P-63 and five in the B-17. [52]
Data fromJane's Fighting Aircraft of World War II. [53]
General characteristics
Performance
Armament
Related development
Aircraft of comparable role, configuration, and era
Related lists
The Curtiss P-40 Warhawk is an American single-engined, single-seat, all-metal fighter-bomber that first flew in 1938. The P-40 design was a modification of the previous Curtiss P-36 Hawk which reduced development time and enabled a rapid entry into production and operational service. The Warhawk was used by most Allied powers during World War II, and remained in frontline service until the end of the war. It was the third most-produced American fighter of World War II, after the P-51 and P-47; by November 1944, when production of the P-40 ceased, 13,738 had been built, all at Curtiss-Wright Corporation's main production facilities in Buffalo, New York.
The Lockheed P-80 Shooting Star was the first jet fighter used operationally by the United States Army Air Forces (USAAF) during World War II. Designed and built by Lockheed in 1943 and delivered just 143 days from the start of design, production models were flying, and two pre-production models did see very limited service in Italy just before the end of World War II. Designed with straight wings, the type saw extensive combat in Korea with the United States Air Force (USAF) as the F-80.
The Bell Aircraft Corporation was an American aircraft manufacturer, a builder of several types of fighter aircraft for World War II but most famous for the Bell X-1, the first supersonic aircraft, and for the development and production of many important civilian and military helicopters. Bell also developed the Reaction Control System for the Mercury Spacecraft, North American X-15, and Bell Rocket Belt. The company was purchased in 1960 by Textron, and lives on as Bell Textron.
The Bell XP-52 and subsequent XP-59 were World War II fighter aircraft design projects by the American Bell Aircraft Corporation.
The Bell P-59 Airacomet was a single-seat, twin jet-engine fighter aircraft that was designed and built by Bell Aircraft during World War II. It was the first jet produced in the United States. As the British were further along in jet engine development, they donated an engine for the United States to copy in 1941 that became the basis for the General Electric J31 jet engine used by the P-59 a year later. Because the plane was underpowered, the United States Army Air Forces (USAAF) was not impressed by its performance and canceled half of the original order for 100 fighters, using the completed aircraft as trainers. The USAAF would instead go on to select the Lockheed P-80 Shooting Star as its first operational jet fighter. Although no P-59s entered combat, the aircraft paved the way for later generations of U.S. turbojet-powered aircraft.
Alexander Ivanovich Pokryshkin was a Soviet fighter pilot in World War II, and later a Marshal of Aviation. He was one of the highest-scoring Soviet aces, and the highest-scoring pilot ever to fly an American aircraft, having achieved the great majority of his kills in the Lend-Lease Bell P-39 Airacobra. During the war Pokryshkin earned the title Hero of the Soviet Union three times: 24 May 1943, 24 August 1943, and 19 August 1944. After the war, he served in the Soviet Air Defense Forces, reaching the rank of Marshal of Aviation; he retired in 1981.
The Bell P-39 Airacobra is a fighter produced by Bell Aircraft for the United States Army Air Forces during World War II. It was one of the principal American fighters in service when the United States entered combat. The P-39 was used by the Soviet Air Force, and enabled individual Soviet pilots to score the highest number of kills attributed to any U.S. fighter type flown by any air force in any conflict. Other major users of the type included the Free French, the Royal Air Force, and the Italian Co-Belligerent Air Force.
The Grumman F7F Tigercat is a heavy fighter aircraft that served with the United States Navy (USN) and United States Marine Corps (USMC) from late in World War II until 1954. It was the first twin-engine fighter to be deployed by the USN. While the Tigercat was delivered too late to see combat in World War II, it saw action as a night fighter and attack aircraft during the Korean War.
Alvin Melvin "Tex" Johnston was an American test pilot for Bell Aircraft and the Boeing Company.
The Bell XFL Airabonita was an American experimental carrier-based interceptor aircraft developed for the United States Navy by Bell Aircraft Corporation of Buffalo, New York. It was similar to and a parallel development of the U.S. Army Air Corps’ land-based P-39 Airacobra, differing mainly in the use of a tailwheel undercarriage in place of the P-39's tricycle gear. Only one prototype was built.
The Fisher P-75 Eagle was an American fighter aircraft designed by the Fisher Body Division of General Motors. Development started in September 1942 in response to United States Army Air Forces requirement for a fighter possessing an extremely high rate of climb, using the most powerful liquid-cooled engine then available, the Allison V-3420. The program was cancelled after only a small number of prototypes and production aircraft had been completed, as it was no longer required in its original role, could not be quickly deployed, and possessed no significant advantages over aircraft already in production.
The McDonnell XP-67 "Bat" or "Moonbat" was a prototype for a twin-engine, long-range, single-seat interceptor aircraft for the United States Army Air Forces. Although the design was conceptually advanced, it was beset by numerous problems and never approached its anticipated level of performance. The project was cancelled after the sole completed prototype was destroyed by an engine fire.
The Bell P-76 was the proposed designation for a production model derivative of the XP-39E, a single-engine American fighter aircraft prototype of World War II.
Tucker XP-57 was the designation of a lightweight fighter which was proposed to the United States Army Air Corps (USAAC) in 1940. Nicknamed the "Peashooter", it was developed by the Tucker Aviation Corporation under Preston Tucker, who later became famous for the Tucker '48 Sedan.
The 37 mm Automatic Gun, M4, known as the T9 during development, was a 37 mm (1.46 in) recoil-operated autocannon designed by Browning Arms Company. The weapon, which was built by Colt, entered service in 1942. It was primarily mounted in the Bell P-39 Airacobra and P-63 Kingcobra, with the U.S. Navy also utilizing it on many PT boats.
ALSIB was the Soviet Union portion of the Alaska-Siberian air road receiving Lend-Lease aircraft from the Northwest Staging Route. Aircraft manufactured in the United States were flown over this route for World War II combat service on the Eastern Front.
The Piaggio P.119 was an Italian experimental fighter of World War II. It had a relatively novel layout, with a "buried" radial engine mounted mid-fuselage. Only a single prototype was built before the Armistice between Italy and the allied armed forces, which ended the project.
The Bell L-39 was an experimental aircraft used to test the characteristics of swept wings.
The Kawasaki Ki-88 was a proposed Japanese World War II fighter aircraft intended for use by the Imperial Japanese Army Air Force. Its anticipated performance was disappointing, and only a mock-up was completed.
The Wings Museum is an aviation museum located in Sussex, United Kingdom. It is housed in a 12,000 square feet (1,100 m2) hangar-like former farm building in Brantridge Lane, between Handcross and Balcombe. The museum displays mainly World War II-related flying memorabilia and equipment which have been donated, or which have been recovered and restored by volunteers.