Heating film

Last updated

A set of heating film before installation Carbon-heating-film.jpg
A set of heating film before installation

Heating films are a method of electric resistance heating, providing relatively low temperatures (compared to many conventional heating systems) over large areas. Heating films can be directly installed to provide underfloor heating, wall radiant heating and ceiling radiant heating.

Contents

The films can also be used in heating panels to produce wall or ceiling panel heaters.

Although heating films do not usually run at very high temperatures (typically 30 °C (86 °F) on floors and up to 40 °C (104 °F) on walls), due to the large surface area they cover, they can provide significant energy output. Also due to the low temperature, undesirable heat losses can be lower, when compared to higher temperature wet heating systems with losses from long pipe runs from the central heating source.

Description

Electric resistance heating films consist of a substrate film, most commonly made from plastic, printed or coated with a resistance material and electric contact busbars. This is laminated or coated with another layer of insulating film, usually similar to the substrate.

Electrical contacts can be made using various types of crimp contacts, which make contact through the covering films to the internal busbars. If the operating voltage is high enough, the contacts must be additionally insulated and additional safety insulation or safety earth covering must be provided over the film to protect users from shock, in case of damage to the installed film.

Heating films can be used as a replacement for conventional heating systems, as a primary heat source or used to augment existing systems.

Due to the simplicity of installation and ease of hiding the installation, it can be popular with DIY installers. The films can be placed or removed when needed, when installed under carpets of other easily removable floor covering. Heating controllers can allow the residents to select which surface will be heated.

Films are available with different power outputs per m2. The required power output will depend on the area covered, building insulation, required energy input to the room and maximum desired surface temperature. Many countries have regulations for the maximum floor or wall temperature. Thermostats with surface temperature sensors may be required in these jurisdictions.

This heating system is mainly used in Asian countries like Korea, where it is considered as a modern version of ondol heating. [1] [2] [3] Some heating films are semi-permanent, meaning that they need to be changed after a certain period of use, and are not widely available everywhere. However, many modern heating films can be considered permanent, lasting at least 20 years with no degradation in performance.

Heating films are becoming increasingly popular globally [4]

A heating film roll Heating film wiki.jpg
A heating film roll

Ondol radiant floor heating

An ondol , also called gudeul (Korean: 구들), in Korean traditional architecture, is underfloor heating which uses direct heat transfer from wood smoke to the underside of a thick masonry floor. Many modern Korean houses use a radiant underfloor heating system that's called ondol, referring to the traditional ondol heating system. In fact, Korean people refer to any domestic heating system as ondol.

Technically, the modern day ondol is based on the same concept as the underfloor radiant heating invented by the American architect Frank Lloyd Wright, who was interested in Japanese architecture. Wright came with the idea while visiting a Japanese nobleman's house, where he found a tea room that was different from the rest of the house, using a Korean ondol as a heating system. He then took the same idea to create a heating system that fits American houses. Wright invented modern radiant floor heating, using hot water running through pipes instead of hot air through flues. [5]

A heating film, itself, is a variation of the modern ondol, but it doesn't require hot water and pipes as it is fully electric. There are also many variations of this underfloor heating system, as many underfloor heaters are based on PTC heating element, far-infrared rays, carbon film, or cables, etc. [6]

Operating voltage

Heating films for domestic heating are available to be powered directly from the mains electricity supply in different countries, e.g. 120 volts AC, 220 volts AC, etc. or low voltage, e.g. 24 volts.

Mains voltage

In general, due to safety issues, heating films supplied directly from the mains are only installed underfloor or in ceilings. Due to potentially hazardous voltages from mains electricity, protection from electric shock is usually required, either due to damage (e.g. nails) or water ingress. Most commonly, additional insulation layers are added over the heating film and sealed with waterproof tapes, although this does not provide protection from shock due to damage like nails. Metalised bags or sheets, connected to earth can also be used, relying on earth leakage (RCD) protection devices on the mains supply to provide protection from shock due to damage.

Due to the additional protection layers, the heating efficiency of mains films can be reduced, however the lack of power supply makes these types of heating film attractive.

Low voltage

Low voltage heating films are usually designed to function at voltages within SELV range and therefore present no danger of shock. Operation at such voltages means that the films have many fewer limitations on where and how they can be installed, however higher currents are required for operation, requiring thicker wires and voltage converting isolation transformers or power supplies to run from the local mains. Alternatively, low voltage heating films may be suitable for off grid installations where battery, solar, wind or other power is available at the required voltage and current.

Low voltage heating films can be particularly suitable for use in wet areas, where water ingress is a possibility.

Low voltage heating films are also suitable for installation on walls to provide radiant heating. These films can include surface finishes designed to take plaster coatings directly onto the installed film. Due to the low voltage, they are completely electric shock safe when damaged due to nails, screws or when other fittings are put directly through the film. Breaks in the resistive film will affect the power output and metal bridges could cause excessive localised heating due to increased current flow and should not be made across breaks in the film. Breaks in the busbars would also cause functional issues.

It is also possible to install low voltage heating films connected directly to the mains, by connecting sufficient of the sheets in series. However, in this case, similar insulation and shock protection would be required as for mains film installations.

Heating films installed in walls and ceilings, provide heating predominantly using infrared or far infrared radiation, directly to the occupants of a room. Underfloor heating can also provides radiant heat, but floor coverings must be selected to provide infrared transmission and heat conduction.

Greenhouse gas emissions of heating film

The greenhouse gas emissions of heating film is split between manufacture, shipping, installation and operational emissions.

Manufacture

Due to variations between the construction of heating films from different manufacturers, calculations for greenhouse gas emissions to manufacture the products should be made for each manufacturer's film.

Most heating films use plastic films, typically PET. These films can be produced from various sources, including recycling, which should be taken into account. Even where the plastic is recycled or derived from renewable sources, energy will be required to produce it and this must be accounted for.

The resistance layer can be made in many different ways. Typically it is carbon based, with various other chemicals to make it adhere to the substrate sheet. All of these components must be accounted for when considering manufacturing emissions.

The copper busbars, although small, will be a source of emissions. The copper may be printed as particles, which will require suitable chemicals to provide adhesion or stuck on as a ribbon, which will also require suitable adhesive chemicals. Silver particles may also be used to provide additional conductivity between the copper and resistance layer.

Shipping

Heating films are lightweight, typically 200 to 300 grams per square metre (0.061 lb/sq ft). Greenhouse gas emissions due to shipping will depend on distance travelled and transport method. Assuming the heating film travels a similar distance to other heating systems from manufacturer to installation, due to its comparatively low weight, emissions to ship heating film will be comparatively lower.

Installation

Installation of heating films will consume almost no energy when installed underfloor. Where adhesives are used for installation, e.g. on walls and ceilings, the emissions involved in manufacturing and shipping the adhesive must also be included. Some adhesives can produce environmentally damaging emissions as they cure. Low emission adhesives should be used or these emissions must be taken into account when considering installation emissions.

Wiring could also add emissions, where cable runs through walls and floors need to be provided.

Operating emissions

Since heating films are powered by electricity, no direct emissions will occur at the installation. The operating emissions will depend entirely on the electricity source and emissions will occur wherever the electricity is generated.

E.g. where the heating film is supplied directly by nuclear, wind or solar energy, the greenhouse gas emissions will be zero. Where the electricity is supplied by mains electricity in a region where the electricity is produced from coal, the overall operating greenhouse gas emission will be high.

However, most countries are aiming to reduce greenhouse gas emissions for electricity generation. In countries where these policies are in place, heating film supplied from the mains can be considered to produce lower greenhouse gas emissions than coal, oil or gas heating systems and this will tend to improve over time.

Transparent heating film

Transparent heating films are a variant of the basic heating films but are built according to a different architecture. It consists of a thin and flexible polymer film with a conductive optical coating. These heating films can be used in museums as a replacement for heating tables [7]

Related Research Articles

<span class="mw-page-title-main">Heat pump</span> System that transfers heat from one space to another

A heat pump is a device that consumes work to transfer heat from a cold heat sink to a hot heat sink. Specifically, the heat pump transfers thermal energy using a refrigeration cycle, cooling the cool space and warming the warm space. In cold weather, a heat pump can move heat from the cool outdoors to warm a house ; the pump may also be designed to move heat from the house to the warmer outdoors in warm weather. As they transfer heat rather than generating heat, they are more energy-efficient than other ways of heating or cooling a home.

<span class="mw-page-title-main">Hypocaust</span> Ancient Roman system of underfloor heating

A hypocaust is a system of central heating in a building that produces and circulates hot air below the floor of a room, and may also warm the walls with a series of pipes through which the hot air passes. This air can warm the upper floors as well. The word derives from the Ancient Greek hypo meaning "under" and caust-, meaning "burnt". The earliest reference to such a system suggests that the Temple of Ephesus in 350 BC was heated in this manner, although Vitruvius attributes its invention to Sergius Orata in c. 80 BC. Its invention improved the hygiene and living conditions of citizens, and was a forerunner of modern central heating.

<span class="mw-page-title-main">Water heating</span> Thermodynamic process that uses energy sources to heat water

Water heating is a heat transfer process that uses an energy source to heat water above its initial temperature. Typical domestic uses of hot water include cooking, cleaning, bathing, and space heating. In industry, hot water and water heated to steam have many uses.

<span class="mw-page-title-main">Solar water heating</span> Use of sunlight for water heating with a solar thermal collector

Solar water heating (SWH) is heating water by sunlight, using a solar thermal collector. A variety of configurations are available at varying cost to provide solutions in different climates and latitudes. SWHs are widely used for residential and some industrial applications.

<span class="mw-page-title-main">Central heating</span> Type of heating system

A central heating system provides warmth to a number of spaces within a building from one main source of heat. It is a component of heating, ventilation, and air conditioning systems, which can both cool and warm interior spaces.

<span class="mw-page-title-main">High voltage</span> Electrical potential which is large enough to cause damage or injury

High voltage electricity refers to electrical potential large enough to cause injury or damage. In certain industries, high voltage refers to voltage above a certain threshold. Equipment and conductors that carry high voltage warrant special safety requirements and procedures.

<i>Ondol</i> Traditional Korean underfloor heating system

Ondol or gudeul in Korean traditional architecture is underfloor heating that uses direct heat transfer from wood smoke to heat the underside of a thick masonry floor. In modern usage it refers to any type of underfloor heating, or to a hotel or a sleeping room in Korean style.

Low emissivity refers to a surface condition that emits low levels of radiant thermal (heat) energy. All materials absorb, reflect, and emit radiant energy according to Planck's law but here, the primary concern is a special wavelength interval of radiant energy, namely thermal radiation of materials. In common use, especially building applications, the temperature range of approximately -40 to +80 degrees Celsius is the focus, but in aerospace and industrial process engineering, much broader ranges are of practical concern.

<span class="mw-page-title-main">Electric heating</span> Process in which electrical energy is converted to heat

Electric heating is a process in which electrical energy is converted directly to heat energy. Common applications include space heating, cooking, water heating and industrial processes. An electric heater is an electrical device that converts an electric current into heat. The heating element inside every electric heater is an electrical resistor, and works on the principle of Joule heating: an electric current passing through a resistor will convert that electrical energy into heat energy. Most modern electric heating devices use nichrome wire as the active element; the heating element, depicted on the right, uses nichrome wire supported by ceramic insulators.

<span class="mw-page-title-main">Electrical bonding</span> Method of protection from electric shock

Electrical bonding is the practice of intentionally electrically connecting all exposed metal items not designed to carry electricity in a room or building as protection from electric shock. Bonding is also used to minimize electrical arcing between metal surfaces with electrical potential differences. If a failure of electrical insulation occurs, all bonded metal objects in the room will have substantially the same electrical potential, so that an occupant of the room cannot touch two objects with significantly different potentials. Even if the connection to a distant earth is lost, the occupant will be protected from dangerous potential differences.

Renewable heat is an application of renewable energy referring to the generation of heat from renewable sources; for example, feeding radiators with water warmed by focused solar radiation rather than by a fossil fuel boiler. Renewable heat technologies include renewable biofuels, solar heating, geothermal heating, heat pumps and heat exchangers. Insulation is almost always an important factor in how renewable heating is implemented.

<span class="mw-page-title-main">Underfloor heating</span> Form of central heating and cooling

Underfloor heating and cooling is a form of central heating and cooling that achieves indoor climate control for thermal comfort using hydronic or electrical heating elements embedded in a floor. Heating is achieved by conduction, radiation and convection. Use of underfloor heating dates back to the Neoglacial and Neolithic periods.

<span class="mw-page-title-main">Air source heat pump</span> Most common type of heat pump

An air source heat pump (ASHP) is a heat pump that can absorb heat from air outside a building and release it inside; it uses the same vapor-compression refrigeration process and much the same equipment as an air conditioner, but in the opposite direction. ASHPs are the most common type of heat pump and, usually being smaller, tend to be used to heat individual houses or flats rather than blocks, districts or industrial processes.

<span class="mw-page-title-main">Ground source heat pump</span> System to transfer heat to/from the ground

A ground source heat pump is a heating/cooling system for buildings that use a type of heat pump to transfer heat to or from the ground, taking advantage of the relative constancy of temperatures of the earth through the seasons. Ground-source heat pumps (GSHPs) – or geothermal heat pumps (GHP), as they are commonly termed in North America – are among the most energy-efficient technologies for providing HVAC and water heating, using far less energy than can be achieved by burning a fuel in a boiler/furnace or by use of resistive electric heaters.

<span class="mw-page-title-main">Wood flooring</span> Product manufactured from timber that is designed for use as flooring

Wood flooring is any product manufactured from timber that is designed for use as flooring, either structural or aesthetic. Wood is a common choice as a flooring material and can come in various styles, colors, cuts, and species. Bamboo flooring is often considered a form of wood flooring, although it is made from bamboo rather than timber.

<span class="mw-page-title-main">Infrared heater</span> Device designed to create radiative heat

An infrared heater or heat lamp is a heating appliance containing a high-temperature emitter that transfers energy to a cooler object through electromagnetic radiation. Depending on the temperature of the emitter, the wavelength of the peak of the infrared radiation ranges from 750 nm to 1 mm. No contact or medium between the emitter and cool object is needed for the energy transfer. Infrared heaters can be operated in vacuum or atmosphere.

<span class="mw-page-title-main">Solar hot water in Australia</span>

Solar hot water refers to water heated by solar energy, a renewable energy source derived from the sun. This process involves thermal collectors, often called solar panels, which absorb solar energy to increase the temperature of the water. The heated water is then stored in a reservoir tank for future use. Solar hot water systems are utilized for a variety of purposes, including domestic and commercial water heating, contributing to heating and cooling systems, and providing process heat for industrial applications.

Zero-carbon housing is housing that does not emit greenhouse gasses (GHGs) into the atmosphere, either directly, or indirectly due to consumption electricity produced using fossil fuels. Most commonly zero-carbon housing is taken to mean zero emissions of carbon dioxide, which is the main climate pollutant from homes, although fugitive methane may also be emitted from natural gas pipes and appliances.

<span class="mw-page-title-main">Mechanical, electrical, and plumbing</span> Subfields of building design and construction

Mechanical, electrical and plumbing (MEP) refers to the installation of services which provide a functional and comfortable space for the building occupants. In residential and commercial buildings, these elements are often designed by specialized MEP engineers. MEP's design is important for planning, decision-making, accurate documentation, performance- and cost-estimation, construction, and operating/maintaining the resulting facilities.

<span class="mw-page-title-main">Radiant heating and cooling</span> Category of HVAC technologies

Radiant heating and cooling is a category of HVAC technologies that exchange heat by both convection and radiation with the environments they are designed to heat or cool. There are many subcategories of radiant heating and cooling, including: "radiant ceiling panels", "embedded surface systems", "thermally active building systems", and infrared heaters. According to some definitions, a technology is only included in this category if radiation comprises more than 50% of its heat exchange with the environment; therefore technologies such as radiators and chilled beams are usually not considered radiant heating or cooling. Within this category, it is practical to distinguish between high temperature radiant heating, and radiant heating or cooling with more moderate source temperatures. This article mainly addresses radiant heating and cooling with moderate source temperatures, used to heat or cool indoor environments. Moderate temperature radiant heating and cooling is usually composed of relatively large surfaces that are internally heated or cooled using hydronic or electrical sources. For high temperature indoor or outdoor radiant heating, see: Infrared heater. For snow melt applications see: Snowmelt system.

References

  1. "Ondol heating – Heating film | Heating Cable | Thermostats". Archived from the original on June 23, 2015. Retrieved June 9, 2015.
  2. How do I use my heating? | whatawaygook
  3. Traditional Korean Heating System
  4. "Global Infrared Heating Films Market to witness a CAGR of 10.76% during 2018-2024 - MarketWatch". www.marketwatch.com. Archived from the original on June 20, 2019.
  5. Radiant floor heating systems by Elektra and Ideal-Heating.com : ARTICLE 'The flow of ideas: From the West to the East and from the East to the West.'
  6. "Infrared heating Electricity consumption". January 2, 2016.
  7. "Archived copy". Archived from the original on March 4, 2016. Retrieved June 29, 2015.{{cite web}}: CS1 maint: archived copy as title (link)