Dynamic frequency scaling

Last updated

Dynamic frequency scaling (also known as CPU throttling) is a power management technique in computer architecture whereby the frequency of a microprocessor can be automatically adjusted "on the fly" depending on the actual needs, to conserve power and reduce the amount of heat generated by the chip. Dynamic frequency scaling helps preserve battery on mobile devices and decrease cooling cost and noise on quiet computing settings, or can be useful as a security measure for overheated systems (e.g. after poor overclocking).

Contents

Dynamic frequency scaling almost always appear in conjunction with dynamic voltage scaling, since higher frequencies require higher supply voltages for the digital circuit to yield correct results. The combined topic is known as dynamic voltage and frequency scaling (DVFS).

Operation

The dynamic power ( switching power ) dissipated by a chip is C·V2·A·f, where C is the capacitance being switched per clock cycle, V is voltage, A is the Activity Factor [1] indicating the average number of switching events per clock cycle by the transistors in the chip (as a unitless quantity) and f is the clock frequency. [2]

Voltage is therefore the main determinant of power usage and heating. [3] The voltage required for stable operation is determined by the frequency at which the circuit is clocked, and can be reduced if the frequency is also reduced. [4] Dynamic power alone does not account for the total power of the chip, however, as there is also static power, which is primarily because of various leakage currents. Due to static power consumption and asymptotic execution time it has been shown that the energy consumption of software shows convex energy behavior, i.e., there exists an optimal CPU frequency at which energy consumption is minimized. [5] Leakage current has become more and more important as transistor sizes have become smaller and threshold voltage levels are reduced. A decade ago, dynamic power accounted for approximately two-thirds of the total chip power. The power loss due to leakage currents in contemporary CPUs and SoCs tend to dominate the total power consumption. In the attempt to control the leakage power, high-k metal-gates and power gating have been common methods.

Dynamic voltage scaling is another related power conservation technique that is often used in conjunction with frequency scaling, as the frequency that a chip may run at is related to the operating voltage.

The efficiency of some electrical components, such as voltage regulators, decreases with increasing temperature, so the power usage may increase with temperature. Since increasing power use may increase the temperature, increases in voltage or frequency may increase system power demands even further than the CMOS formula indicates, and vice versa. [6] [7]

Standard interface

ACPI 1.0 (1996) defines a way for a CPU to go to idle "C states", but defines no frequency-scaling system.

ACPI 2.0 (2000) introduces a system of P states (power-performance states) that a processor can use to communicate its possible frequency–power settings to the OS. The operating system then sets the speed as needed by switching between these states. SpeedStep, PowerNow!/Cool'n'Quiet, and PowerSaver all work through P states. There is a limit of 16 states maximum. [8]

ACPI 5.0 (2011) introduces collaborative processor performance control (CPPC), exposing hundreds of performance levels to the OS for selection in the form of a "performance level" abstracted away from the frequency. This abstraction provides some leeway for the processor to adjust its workings in ways other than just the frequency. [9] [10] [11]

Autonomous frequency scaling

A number of modern CPUs can perform frequency scaling autonomously, using a performance level range and a "efficiency/performance preference" hint from the OS.

Performance impact

Dynamic frequency scaling reduces the number of instructions a processor can issue in a given amount of time, thus reducing performance. Hence, it is generally used when the workload is not CPU-bound.

Dynamic frequency scaling by itself is rarely worthwhile as a way to conserve switching power. Saving the highest possible amount of power requires dynamic voltage scaling too, because of the V2 component and the fact that modern CPUs are strongly optimized for low power idle states. In most constant-voltage cases, it is more efficient to run briefly at peak speed and stay in a deep idle state for longer time (called "race to idle" or computational sprinting), than it is to run at a reduced clock rate for a long time and only stay briefly in a light idle state. However, reducing voltage along with clock rate can change those trade-offs.

A related-but-opposite technique is overclocking, whereby processor performance is increased by ramping the processor's (dynamic) frequency beyond the manufacturer's design specifications.

One major difference between the two is that in modern PC systems overclocking is mostly done over the Front Side Bus (mainly because the multiplier is normally locked), but dynamic frequency scaling is done with the multiplier. Moreover, overclocking is often static, while dynamic frequency scaling is always dynamic. Software can often incorporate overclocked frequencies into the frequency scaling algorithm, if the chip degradation risks are allowable.

Support across vendors

Intel

Intel's CPU throttling technology, SpeedStep, is used in its mobile and desktop CPU lines.

AMD

AMD employs two different CPU throttling technologies. AMD's Cool'n'Quiet technology is used on its desktop and server processor lines. The aim of Cool'n'Quiet is not to save battery life, as it is not used in AMD's mobile processor line, but instead with the purpose of producing less heat, which in turn allows the system fan to spin down to slower speeds, resulting in cooler and quieter operation, hence the name of the technology. AMD's PowerNow! CPU throttling technology is used in its mobile processor line, though some supporting CPUs like the AMD K6-2+ can be found in desktops as well.

AMD PowerTune and AMD ZeroCore Power are dynamic frequency scaling technologies for GPUs.

VIA Technologies

VIA Technologies processors use a technology named LongHaul (PowerSaver), while Transmeta's version was called LongRun.

The 36-processor AsAP 1 chip is among the first multi-core processor chips to support completely unconstrained clock operation (requiring only that frequencies are below the maximum allowed) including arbitrary changes in frequency, starts, and stops. The 167-processor AsAP 2 chip is the first multi-core processor chip which enables individual processors to make fully unconstrained changes to their own clock frequencies.

According to the ACPI Specs, the C0 working state of a modern-day CPU can be divided into the so-called "P"-states (performance states) which allow clock rate reduction and "T"-states (throttling states) which will further throttle down a CPU (but not the actual clock rate) by inserting STPCLK (stop clock) signals and thus omitting duty cycles.

ARM

Different ARM-based systems on chip provide CPU and GPU throttling.

See also

Power Saving Technologies:

Performance Boosting Technologies:

Related Research Articles

<span class="mw-page-title-main">Athlon</span> Brand of microprocessors by AMD

Athlon is the brand name applied to a series of x86-compatible microprocessors designed and manufactured by AMD. The original Athlon was the first seventh-generation x86 processor and the first desktop processor to reach speeds of one gigahertz (GHz). It made its debut as AMD's high-end processor brand on June 23, 1999. Over the years AMD has used the Athlon name with the 64-bit Athlon 64 architecture, the Athlon II, and Accelerated Processing Unit (APU) chips targeting the Socket AM1 desktop SoC architecture, and Socket AM4 Zen microarchitecture. The modern Zen-based Athlon with a Radeon Graphics processor was introduced in 2019 as AMD's highest-performance entry-level processor.

<span class="mw-page-title-main">Pentium 4</span> Brand by Intel

Pentium 4 is a series of single-core CPUs for desktops, laptops and entry-level servers manufactured by Intel. The processors were shipped from November 20, 2000 until August 8, 2008. It was removed from the official price lists starting in 2010, being replaced by Pentium Dual-Core.

<span class="mw-page-title-main">Overclocking</span> Practice of increasing the clock rate of a computer to exceed that certified by the manufacturer

In computing, overclocking is the practice of increasing the clock rate of a computer to exceed that certified by the manufacturer. Commonly, operating voltage is also increased to maintain a component's operational stability at accelerated speeds. Semiconductor devices operated at higher frequencies and voltages increase power consumption and heat. An overclocked device may be unreliable or fail completely if the additional heat load is not removed or power delivery components cannot meet increased power demands. Many device warranties state that overclocking or over-specification voids any warranty, but some manufacturers allow overclocking as long as it is done (relatively) safely.

<span class="mw-page-title-main">Athlon 64</span> Series of CPUs by AMD

The Athlon 64 is a ninth-generation, AMD64-architecture microprocessor produced by Advanced Micro Devices (AMD), released on September 23, 2003. It is the third processor to bear the name Athlon, and the immediate successor to the Athlon XP. The Athlon 64 was the second processor to implement the AMD64 architecture and the first 64-bit processor targeted at the average consumer. Variants of the Athlon 64 have been produced for Socket 754, Socket 939, Socket 940, and Socket AM2. It was AMD's primary consumer CPU, and primarily competed with Intel's Pentium 4, especially the Prescott and Cedar Mill core revisions.

Processor power dissipation or processing unit power dissipation is the process in which computer processors consume electrical energy, and dissipate this energy in the form of heat due to the resistance in the electronic circuits.

Underclocking, also known as downclocking, is modifying a computer or electronic circuit's timing settings to run at a lower clock rate than is specified. Underclocking is used to reduce a computer's power consumption, increase battery life, reduce heat emission, and it may also increase the system's stability, lifespan/reliability and compatibility. Underclocking may be implemented by the factory, but many computers and components may be underclocked by the end user.

<span class="mw-page-title-main">Clock rate</span> Frequency at which CPU chip or core is operating

In computing, the clock rate or clock speed typically refers to the frequency at which the clock generator of a processor can generate pulses, which are used to synchronize the operations of its components, and is used as an indicator of the processor's speed. It is measured in the SI unit of frequency hertz (Hz).

Power management is a feature of some electrical appliances, especially copiers, computers, computer CPUs, computer GPUs and computer peripherals such as monitors and printers, that turns off the power or switches the system to a low-power state when inactive. In computing this is known as PC power management and is built around a standard called ACPI which superseded APM. All recent computers have ACPI support.

AMD PowerNow! is AMD's dynamic frequency scaling and power saving technology for laptop processors. The CPU's clock speed and VCore are automatically decreased when the computer is under low load or idle, to save battery power, reduce heat and noise. The lifetime of the CPU is also extended because of reduced electromigration, which varies exponentially with temperature.

AMD Cool'n'Quiet is a CPU dynamic frequency scaling and power saving technology introduced by AMD with its Athlon XP processor line. It works by reducing the processor's clock rate and voltage when the processor is idle. The aim of this technology is to reduce overall power consumption and lower heat generation, allowing for slower cooling fan operation. The objectives of cooler and quieter result in the name Cool'n'Quiet. The technology is similar to Intel's SpeedStep and AMD's own PowerNow!, which were developed with the aim of increasing laptop battery life by reducing power consumption.

The CPU core voltage (VCORE) is the power supply voltage supplied to the processing cores of CPU, GPU, or any other device with a processing core. The amount of power a CPU uses, and thus the amount of heat it dissipates, is the product of this voltage and the current it draws. In modern CPUs, which are CMOS circuits, the current is almost proportional to the clock speed, the CPU drawing almost no current between clock cycles.

Enhanced SpeedStep is a series of dynamic frequency scaling technologies built into some Intel microprocessors that allow the clock speed of the processor to be dynamically changed by software. This allows the processor to meet the instantaneous performance needs of the operation being performed, while minimizing power draw and heat generation. EIST was introduced in several Prescott 6 series in the first quarter of 2005, namely the Pentium 4 660. Intel Speed Shift Technology (SST) was introduced in Intel Skylake Processor.

<span class="mw-page-title-main">P6 (microarchitecture)</span> Intel processor microarchitecture

The P6 microarchitecture is the sixth-generation Intel x86 microarchitecture, implemented by the Pentium Pro microprocessor that was introduced in November 1995. It is frequently referred to as i686. It was planned to be succeeded by the NetBurst microarchitecture used by the Pentium 4 in 2000, but was revived for the Pentium M line of microprocessors. The successor to the Pentium M variant of the P6 microarchitecture is the Core microarchitecture which in turn is also derived from P6.

The Intel Core microarchitecture is a multi-core processor microarchitecture launched by Intel in mid-2006. It is a major evolution over the Yonah, the previous iteration of the P6 microarchitecture series which started in 1995 with Pentium Pro. It also replaced the NetBurst microarchitecture, which suffered from high power consumption and heat intensity due to an inefficient pipeline designed for high clock rate. In early 2004 the new version of NetBurst (Prescott) needed very high power to reach the clocks it needed for competitive performance, making it unsuitable for the shift to dual/multi-core CPUs. On May 7, 2004 Intel confirmed the cancellation of the next NetBurst, Tejas and Jayhawk. Intel had been developing Merom, the 64-bit evolution of the Pentium M, since 2001, and decided to expand it to all market segments, replacing NetBurst in desktop computers and servers. It inherited from Pentium M the choice of a short and efficient pipeline, delivering superior performance despite not reaching the high clocks of NetBurst.

In computer architecture, dynamic voltage scaling is a power management technique in which the voltage used in a component is increased or decreased, depending upon circumstances. Dynamic voltage scaling to increase voltage is known as overvolting; dynamic voltage scaling to decrease voltage is known as undervolting. Undervolting is done in order to conserve power, particularly in laptops and other mobile devices, where energy comes from a battery and thus is limited, or in rare cases, to increase reliability. Overvolting is done in order to support higher frequencies for performance.

Low-power electronics are electronics, such as notebook processors, that have been designed to use less electric power than usual, often at some expense. In the case of notebook processors, this expense is processing power; notebook processors usually consume less power than their desktop counterparts, at the expense of lower processing power.

<span class="mw-page-title-main">Phenom II</span> Family of AMD multi-core 45 nm processors

Phenom II is a family of AMD's multi-core 45 nm processors using the AMD K10 microarchitecture, succeeding the original Phenom. Advanced Micro Devices released the Socket AM2+ version of Phenom II in December 2008, while Socket AM3 versions with DDR3 support, along with an initial batch of triple- and quad-core processors were released on February 9, 2009. Dual-processor systems require Socket F+ for the Quad FX platform. The next-generation Phenom II X6 was released on April 27, 2010.

Intel Turbo Boost is Intel's trade name for central processing units (CPUs) dynamic frequency scaling feature that automatically raises certain versions of its operating frequency when demanding tasks are running, thus enabling a higher resulting performance.

<span class="mw-page-title-main">AMD PowerTune</span> Brand name by AMD

AMD PowerTune is a series of dynamic frequency scaling technologies built into some AMD GPUs and APUs that allow the clock speed of the processor to be dynamically changed by software. This allows the processor to meet the instantaneous performance needs of the operation being performed, while minimizing power draw, heat generation and noise avoidance. AMD PowerTune aims to solve thermal design power and performance constraints.

AMD Turbo Core a.k.a. AMD Core Performance Boost (CPB) is a dynamic frequency scaling technology implemented by AMD that allows the processor to dynamically adjust and control the processor operating frequency in certain versions of its processors which allows for increased performance when needed while maintaining lower power and thermal parameters during normal operation. AMD Turbo Core technology has been implemented beginning with the Phenom II X6 microprocessors based on the AMD K10 microarchitecture. AMD Turbo Core is available with some AMD A-Series accelerated processing units.

References

  1. ↑ K. Moiseev, A. Kolodny and S. Wimer (September 2008). "Timing-aware power-optimal ordering of signals". ACM Transactions on Design Automation of Electronic Systems. 13 (4): 1–17. doi:10.1145/1391962.1391973. S2CID   18895687.
  2. ↑ Rabaey, J. M. (1996). Digital Integrated Circuits. Prentice Hall.
  3. ↑ Victoria Zhislina (19 February 2014). "Why has CPU frequency ceased to grow?". Intel.
  4. ↑ https://www.usenix.org/legacy/events/hotpower/tech/full_papers/LeSueur.pdf [ bare URL PDF ]
  5. ↑ Karel De Vogeleer; Memmi, Gerard; Jouvelot, Pierre; Coelho, Fabien (2014). "The Energy/Frequency Convexity Rule: Modeling and Experimental Validation on Mobile Devices". arXiv: 1401.4655 [cs.OH].
  6. ↑ Mike Chin. "Asus EN9600GT Silent Edition Graphics Card". Silent PC Review. p. 5. Retrieved 21 April 2008.
  7. ↑ Mike Chin (19 March 2008). "80 Plus expands podium for Bronze, Silver & Gold". Silent PC Review. Retrieved 21 April 2008.
  8. ↑ "Advanced Configuration and Power Interface Specification, Revision 3.0, Section 2.6 Device and Processor Performance State Definitions" (PDF). ACPI.info. 2 September 2004. p. 23. Archived from the original (PDF) on 28 November 2015. Retrieved 19 August 2015.
  9. ↑ "Collaborative Processor Performance Control (CPPC) — The Linux Kernel documentation". www.kernel.org.
  10. ↑ "8.4. Declaring Processors". ACPI Specification 6.4 documentation.
  11. ↑ "Overview about power and performance tuning for the Windows Server". learn.microsoft.com. 29 August 2022.
  12. ↑ x86_energy_perf_policy(8)  –  Linux Programmer's Manual – Administration and Privileged Commands
  13. ↑ "intel_pstate CPU Performance Scaling Driver — The Linux Kernel documentation". www.kernel.org.
  14. ↑ "amd-pstate CPU Performance Scaling Driver — The Linux Kernel documentation". docs.kernel.org.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.