Sojourner (rover)

Last updated

Sojourner
Sojourner on Mars PIA01122.jpg
Sojourner rover pictured by Pathfinder lander
Mission type Mars rover
Operator NASA
Website Official website
Mission duration
  • Planned: 7 sols (7 days)
  • Actual: 83 sols (85 days),
    landing to final contact
Spacecraft properties
Dry mass11.5 kilograms (25 lb)
Power Solar panel: 13 W
Start of mission
Launch dateDecember 4, 1996, 06:58:07 UTC
Rocket Delta II 7925 D240
Launch site Cape Canaveral LC-17B
Contractor McDonnell Douglas
Deployed from Mars Pathfinder
Deployment dateJuly 5, 1997
End of mission
DeclaredMarch 10, 1998
Last contactSeptember 27, 1997
Mars rover
Landing dateJuly 4, 1997 16:56:55 UTC
Landing site Ares Vallis, Chryse Planitia
19°7′48″N33°13′12″W / 19.13000°N 33.22000°W / 19.13000; -33.22000 (Sojourner rover (Mars Pathfinder))
Distance driven100 metres (330 ft)
Mars Pathfinder Insignia.png
Mars Pathfinder mission patch
NASA Mars rovers
Spirit  →

The robotic Sojourner rover reached Mars on July 4, 1997 as part of the Mars Pathfinder mission. Sojourner was operational on Mars for 92 sols (95 Earth days), and was the first wheeled vehicle to operate on an astronomical object other than the Earth or Moon. The landing site was in the Ares Vallis channel in the Chryse Planitia region of the Oxia Palus quadrangle. [1]

Contents

The rover was equipped with front and rear cameras, and hardware that was used to conduct several scientific experiments. It was designed for a mission lasting 7 sols, with a possible extension to 30 sols, [2] and was active for 83 sols (85 Earth days). The rover communicated with Earth through the Pathfinder base station, which had its last successful communication session with Earth at 3:23 a.m. PDT on September 27, 1997. [3] The last signal from the rover was received on the morning of October 7, 1997. [4]

Sojourner traveled just over 100 meters (330 ft) by the time communication was lost. [5] Its final confirmed command was to remain stationary until October 5, 1997, (sol 91) and then drive around the lander; [6] there is no indication it was able to do so. The Sojourner mission formally ended on March 10, 1998, after all further options were exhausted.

Mission

Sojourner at JPL Marspathrov.jpg
Sojourner at JPL

Sojourner was an experimental vehicle whose main mission was to test in the Martian environment technical solutions that were developed by engineers of the NASA research laboratories. [7] It was necessary to verify whether the design strategy followed had resulted in the construction of a vehicle suitable for the environment it would encounter, despite the limited knowledge of it. Careful analysis of the operations on Mars would make it possible to develop solutions to critical problems identified and to introduce improvements for subsequent planetary exploration missions. One of the mission's main aims was to prove the development of "faster, better and cheaper" spacecraft was possible. Development took three years and cost under $150 million for the lander, and $25 million for the rover; development was faster and less costly than all previous missions. [8]

These objectives required careful selection of the landing site to balance the technical requests with the scientific ones. [9] A large plain was needed for the probe to land and rocky terrain to verify the rover's systems. The choice fell on Ares Vallis in Chryse Planitia, which is characterized by alluvial-looking rock formations. Scholars believed the analysis of the rocks, which lie in what appears to be the outlet of a huge drainage channel, could have confirmed the past presence of liquid water on the surface of Mars and provide details of the surrounding areas, from which the rocks were eroded. [9] [10]

Technical characteristics

Mars Pathfinder lander scheme.jpg
Schematic representation of the lander
Sojourner rover scheme.jpg
Schematic representation of the rover

Sojourner was developed by NASA's Jet Propulsion Laboratory (JPL). It is a six-wheeled, 65 cm (26-inch) long, 48 cm (19-inch) wide and 30 cm (12-inch) high vehicle. In the mission's cruise phase, it occupied an 18 cm (7.1-inch) high space and has a mass of 11.5 kg (25 lb). [11] [12] It was supported by a lander, a tetrahedron-shaped structure with a mass of 250 kg (550 lb), and had a camera, scientific instrumentation, three petals of solar panels, a meteorology mast, [13] and 6 kg (13 lb) of equipment that was required to maintain communications between the rover and the lander. [12] Hardware included a steerable, high-gain X-band antenna that could send approximately 5.5 kilobits per second into a 70 m (230 ft) Deep Space Network antenna, 3.3 m2 (36 sq ft) gallium-arsenide solar arrays that generated 1.1 kW⋅h/day and were capable of providing enough power to transmit for 2–4 hours per sol and maintain 128 megabytes of dynamic memory through the night. [14]

Lander

Lander's IMP camera, see also diagram of the IMP. Mars Pathfinder IMP camera.gif
Lander's IMP camera, see also diagram of the IMP.

One of the lander's main tasks was to support the rover by imaging its operations and sending data from the rover to Earth. The lander had rechargeable batteries and over 2.5 m (8.2 ft) of solar cells on its petals. [15] The lander contained a stereoscopic camera with spatial filters on an expandable pole called Imager for Mars Pathfinder (IMP), [16] [17] and the Atmospheric Structure Instrument/Meteorology Package (ASI/MET) [18] which acted as a Mars meteorological station, collecting data about pressure, temperature, and winds. The MET structure included three windsocks mounted at three heights on a pole, the topmost at about one meter (3.3 ft) and generally registered winds from the west. [19] To provide continuous data, the IMP imaged the windsocks once every daylight hour. These measurements allowed the eolian processes at the landing site, including the particle threshold and the aerodynamic surface roughness, to be measured. [13]

The square eyes of the IMP camera are separated by 15 cm (5.9 in) to provide stereoscopic vision and ranging performance to support rover operations. The dual optical paths are folded by two sets of mirrors to bring the light to a single charge-coupled device (CCD). To minimize moving parts, the IMP is electronically shuttered; half of the CCD is masked and used as a readout zone for the electronic shutter. The optics had an effective pixel resolution of one milliradian per pixel which gives 1 mm (0.039 in) per pixel at a range of one meter (3.3 ft). The camera cylinder is mounted on gimbals that provide rotation freedom of 360° in azimuth and −67° to +90° in elevation. This assembly is supported by an extendible mast that was designed and built by AEC Able Engineering. The mast holds the camera at approximately 1.5 m (4.9 ft) above the Martian surface and extends Pathfinder's horizon to 3.4 km (2.1 miles) on a featureless plane. [14] [20] [21]

Power system

Solar panels of the spare rover, Marie Curie. See also batteries installed on the rover. Solar battery of the Sojourner rover.jpg
Solar panels of the spare rover, Marie Curie. See also batteries installed on the rover.

Sojourner had solar panels and a non-rechargeable lithium-thionyl chloride (LiSOCl2) battery that could provide 150 watt-hours and allowed limited nocturnal operations. Once the batteries were depleted, the rover could only operate during the day. [2] [22] The batteries also allowed the rover's health to be checked while enclosed in the cruise stage while en route to Mars. [23] The rover had 0.22 m2 (2.4 sq ft) of solar cells, which could produce a maximum of about 15 watts on Mars, depending on conditions. [22] The cells were GaAs/Ge (Gallium Arsenide/Germanium) with approximately 18 percent efficiency. They could survive temperatures down to about −140 °C (−220 °F). [23] After about its 40th sol on Mars, the lander's battery no longer held a charge so it was decided to shut off the rover before sunset and wake it up at sunrise. [24]

Locomotion system

Side view Sojourner side view.gif
Side view
Rover in the cruise configuration Sojourner in cruise configuration.gif
Rover in the cruise configuration

The rover's wheels were made of aluminum and were 13 cm (5.1 in) in diameter and 7.9 cm (3.1 in) wide. They had serrated, stainless steel tracks that could generate a pressure of 1.65 kPa (0.239 psi) in optimal conditions on soft ground. [25] No such need arose during the operational phase. [25] Each wheel was driven by its own independent motor. [7] The first and third wheels were used for steering. A six-wheel-steering configuration was considered, but this was too heavy. [25] As the rover rotated on itself, it drew a 74 cm (29 in) wide circle. [7]

The wheels were connected to the frame through specially developed suspension to ensure all six were in contact with the ground, even on rough terrain. [25] [26] JPL's Don Bickler developed the wheels, which were referred to as "Rocker-bogie", for the experimental "Rocky" vehicles, of which the Sojourner is the eighth version. [27] [28] [29] They consisted of two elements; "Bogie" connected the front wheel with the central one and "Rocker" connected the rear wheel with the other two. The system did not include springs or other elastic elements, which could have increased the pressure exerted by each wheel. [25] This system allowed the overcoming of obstacles up to 8 cm (3.1 in) high [11] but theoretically would have allowed the rover to overcome obstacles of 20 cm (7.9 in), or about 30% of the rover's length. [25] The suspension system was also given the ability to collapse on itself so the rover would occupy 18 cm (7.1 in) in the cruising configuration. [30]

The locomotion system was found to be suitable for the environment of Mars—being very stable, and allowing forward and backward movements with similar ease [11] —and was adopted with appropriate precautions in the subsequent Spirit and Opportunity rover missions. [26]

In the ten-year development phase that led to the realization of Sojourner, alternative solutions that could take advantage of the long experience gained at JPL in the development of vehicles for the Moon and Mars were examined. [27] The use of four or more legs was excluded for three reasons: a low number of legs would limit the rover's movements and the freedom of action, and increasing the number would lead to a significant increase in complexity. Proceeding in this configuration would also require knowledge of the space in front—the ground corresponding to the next step—leading to further difficulties. [26] The choice of a wheeled vehicle solved most of the stability problems, led to a reduction in weight, and improved efficiency and control compared to the previous solution. [26] The simplest configuration was a four-wheel system that, however, encounters difficulties in overcoming obstacles. Better solutions were the use of six or eight wheels with the rear ones able to push, allowing the obstacle to be overcome. The lighter, simpler, six-wheeled option was preferred. [26]

The rover could travel 500 m (1,600 ft) from the lander—the approximate limit of its communication range— [13] and had a maximum speed of 1 cm/s (0.39 in/s). [11]

Hardware and software

Power board (bottom side) and CPU board (top side) JPL-26575BC.jpg
Power board (bottom side) and CPU board (top side)

Sojourner's central processing unit (CPU) was an Intel 80C85 with a 2 MHz clock, addressing 64 kilobytes (Kb) of memory, and running a cyclic executive. [31] It had four memory stores; 64 Kb of RAM made by IBM for the main processor, 16 Kb of radiation-hardened PROM made by Harris, 176 Kb of non-volatile storage made by Seeq Technology, and 512 Kb of temporary data storage made by Micron. The electronics were housed inside the rover's warm electronics box (WEB). [2] The WEB is a box-like structure formed from fiberglass facesheets bonded to aluminum spars. The gaps between facesheets were filled with blocks of aerogel that worked as thermal insulation. [32] The aerogel used on the Sojourner had a density of approximately 20 mg/cc. [33] This insulator was designed to trap heat generated by rover's electronics; this trapped heat soaked at night through the passive insulation maintaining the electronics in the WEB at between −40 and 40 °C (−40 and 104 °F), while externally the rover experienced a temperature range between 0 and −110 °C (32 and −166 °F). [2]

The Pathfinder lander's computer was a Radiation Hardened IBM Risc 6000 Single Chip with a Rad6000 SC CPU, 128 megabytes (Mb) of RAM and 6 Mb of EEPROM memory, [34] [35] and its operating system was VxWorks. [36]

The mission was jeopardised by a concurrent software bug in the lander [37] that had been found in preflight testing but was deemed a glitch and given a low priority because it only occurred in certain unanticipated heavy-load conditions, and the focus was on verifying the entry and landing code. The problem, which was reproduced and corrected from Earth using a laboratory duplicate, was due to computer resets caused by priority inversion. No scientific or engineering data was lost after a computer reset but all of the following operations were interrupted until the next day. [38] [39] Resets occurred on July 5, 10, 11 and 14 during the mission [40] before the software was patched on July 21 to enable priority inheritance. [41]

Communication and cameras

Sojourner communicated with its base station using a 9,600 baud radio modem, although error-checking protocols limited communications to a functional rate of 2,400 baud with a theoretical range of about one-half kilometre (0.31 miles). Under normal operation, it would periodically send a "heartbeat" message to the lander. If no response was given, the rover could autonomously return to the location at which the last heartbeat was received. If desired, the same strategy could be used to deliberately extend the rover's operational range beyond that of its radio transceiver, although the rover rarely traveled further than 10 meters (33 ft) from Pathfinder during its mission. [2] The Ultra high frequency (UHF) radio modems operated in half-duplex mode, meaning they could either send or receive data but not both at the same time. The data was communicated in bursts of 2 kB. [42]

The rover was imaged on Mars by the base station's IMP camera system, which also helped determine where the rover should go. [43] The rover had two monochrome cameras in front and a color camera at the rear. Each front camera had an array 484 pixels high by 768 wide. The cameras used CCDs manufactured by Eastman Kodak Company; they were clocked out by CPU, and capable of auto-exposure, Block Truncation Coding (BTC) data compression, bad pixel/column handling, and image data packetizing. [44]

Pixel map of the color camera Pixel map of Sojourner color camera.jpg
Pixel map of the color camera

Both front cameras were coupled with five laser stripe projectors that enabled stereoscopic images to be taken along with measurements for hazard detection in the rover's path. The optics consisted of a window, lens, and field flattener. The window was made of sapphire while the lens objective and flattener were made of zinc selenide. [44]

Another color camera was located on the back of the rover near the APXS, and rotated by 90°. It provided images of the APXS's target area and the rover's ground tracks. [44]

The sensor of this color camera was arranged so 12 of 16 pixels of a 4×4 pixel block were sensitive to green light; while 2 pixels were sensitive to red light and the other 2 were sensitive to infrared and blue light. [44]

Because the rover's cameras had zinc-selenide lenses, which block light with a wavelength shorter than 500 nanometers (nm), no blue light actually reached the blue-and-infrared-sensitive pixels, which therefore recorded only infrared light. [44]

Rover Control Software

Sojourner operation was supported by "Rover Control Software" (RCS) that ran on a Silicon Graphics Onyx2 computer on Earth and allowed command sequences to be generated using a graphical interface. The rover driver would wear 3D goggles supplied with imagery from the base station and would move a virtual model with a specialized joystick. The control software allowed the rover and surrounding terrain to be viewed from any angle, supporting the study of terrain features, the placing of waypoints, and virtual flyovers. Darts were used as icons to show where the rover should go. Desired locations were added to a sequence and sent to the rover to perform. Typically, a long sequence of commands were composed and sent once a day. [45] [46] The rover drivers were Brian K. Cooper and Jack Morrison. [5]

Science payload

Alpha Proton X-Ray Spectrometer

Alpha particle X-ray spectrometer MER APXS PIA05113.jpg
Alpha particle X-ray spectrometer
APXS at the back of the rover Back of Sojourner and its Alpha Proton X-Ray Spectrometer.png
APXS at the back of the rover

The Alpha Proton X-Ray Spectrometer (APXS) was designed to determine the chemical composition of Martian soil, rocks and dust by analyzing the return radiation in its alpha, proton, and X-ray components resulting from the sample's exposure to a radioactive source contained in the instrument. [47] [48] The instrument had a curium-244 source [49] that emits alpha particles with an energy of 5.8 MeV and a half-life of 18.1 years. A portion of the incident radiation that impacted the analyzed sample's surface was reflected and the remainder interacted with the sample. [14]

The principle of the APXS technique is based on the interaction of alpha particles from a radioisotope source with matter. There are three components of the return radiation; simple Rutherford backscattering, production of protons from reactions with the nucleus of light elements, and generation of X-rays upon recombination of atomic shell vacancies created by alpha particle bombardment by interaction with the electrons of the innermost orbitals. [14] The instrument was designed to detect the energy of all three components of the return radiation, making it possible to identify the atoms present and their quantities in a few tens of micrometers below the surface of the analyzed sample. [50] The detection process was rather slow; each measurement could take up to ten hours. [51]

Sensitivity and selectivity depends on a channel; alpha backscattering has high sensitivity for light elements like carbon and oxygen, proton emission is mainly sensitive to sodium, magnesium, aluminium, silicon, sulfur, and X-ray emission is more sensitive to heavier elements sodium to iron and beyond. Combining all three measurements makes APXS sensitive to all elements with the exception of hydrogen that is present at concentration levels above a fraction of one percent. [14] The instrument was designed for the failed Russian Mars-96 mission. [49] The alpha particle and proton detectors were provided by the Chemistry Department of the Max Planck Institute and the X-ray detector was developed by the University of Chicago. [48]

During each measurement, the front surface of the instrument had to be in contact with the sample. [48] For this to be possible, the APXS was mounted on a robotic arm called the Alpha-Proton-X-ray Spectrometer Deployment Mechanism (ADM). The ADM was an anthropomorphic actuator that was equipped with a wrist that was capable of rotations of ±25°. [51] The dual mobility of the rover and the ADM increased the potential of the instrument—the first of its kind to reach Mars. [49]

Wheel Abrasion Experiment

The wheel affected by the Wheel Abrasion Experiment. Mars Pathfinder Wheel Abrasion Experiment.gif
The wheel affected by the Wheel Abrasion Experiment.

The Wheel Abrasion Experiment (WAE) was designed to measure the abrasive action of Martian soil on thin layers of aluminum, nickel, and platinum, and thus deduce the grain size of the soil at the landing site. For this purpose, 15 layers—five of each metal—were mounted on one of the two central wheels with a thickness between 200 and 1000 ångström, and electrically isolated from the rest of the rover. By directing the wheel appropriately, sunlight was reflected towards a nearby photovoltaic sensor. The collected signal was analyzed to determine the desired information. [52] For the abrasive action to be significant on the mission schedule, the rover was scheduled to stop at frequent intervals and, with the other five wheels braked, force the WAE wheel to rotate, causing increased wear. [53] Following the WAE experiment on Mars, attempts were made to reproduce the effects observed in the laboratory. [53]

The interpretation of the results proposed by Ferguson et al. suggests the soil at the landing site is made up of fine-grained dust of limited hardness with a grain size of less than 40 μm. [53] The instrument was developed, built and directed by the Lewis' Photovoltaics and Space Environments Branch of the Glenn Research Center. [53]

Materials Adherence Experiment

The Materials Adherence Experiment (MAE) was designed by engineers at the Glenn Research Center to measure the daily accumulation of dust on the back of the rover and the reduction in the energy-conversion capacity of the photovoltaic panels. [54] [55] It consisted of two sensors. [54]

The first was composed of a photovoltaic cell covered by transparent glass that could be removed on command. Near local midday, measurements of the cell's energy yield were made, both with the glass in place and removed. From the comparison, it was possible to deduce the reduction in cell yield caused by the dust. [54] Results from the first cell were compared with those of a second photovoltaic cell that was exposed to the Martian environment. [54] The second sensor used a quartz crystal microbalance (QCM) to measure the weight-per-surface unit of the dust deposited on the sensor. [54]

During the mission, a daily rate equal to 0.28% of percentage reduction in the energy efficiency of the photovoltaic cells was recorded. This was independent of whether the rover was stationary or in motion. [55] This suggests the dust settling on the rover was suspended in the atmosphere and was not raised by the rover's movements. [52]

Control system

Sojourner overcomes a height difference. Rover movie sol21 S0050N.gif
Sojourner overcomes a height difference.

Since it was established transmissions relating to driving the Sojourner would occur once every sol, the rover was equipped with a computerized control system to guide its movements independently. [56]

A series of commands had been programmed, providing an appropriate strategy for overcoming obstacles. One of the primary commands was "Go to Waypoint". A local reference system, of which the lander was the origin, was envisaged. Coordinate directions were fixed at the moment of landing, taking the direction of north as a reference. During the communication session (once per sol), the rover received from Earth a command string containing the coordinates of the arrival point, which it would have to reach autonomously. [56]

The algorithm implemented on the on-board computer attempted, as a first option, to reach the obstacle in a straight line from the starting position. Using a system of photographic objectives and laser emitters, the rover could identify obstacles along this path. The on-board computer was programmed to search for the signal produced by the lasers in the cameras' images. In the case of a flat surface and no obstacles, the position of this signal was unchanged with respect to the reference signal stored in the computer; any deviation from this position made it possible to identify the type of obstacle. [56] The photographic scan was performed after each advance equal to the diameter of the wheels, 13 cm (5.1 in), and before each turn. [7]

One of the obstacle detection images taken by Sojourner. The laser trace is clearly visible. PIA04316.jpg
One of the obstacle detection images taken by Sojourner. The laser trace is clearly visible.

In the confirmed presence of an obstacle, [a] the computer commanded the execution of a first strategy to avoid it. The rover, still by itself, rotated until the obstacle was no longer in sight. Then, after having advanced for half of its length, it recalculated a new straight path that would lead it to the point of arrival. At the end of the procedure, the computer had no memory of the existence of the obstacle. [56] The steering angle of the wheels was controlled through potentiometers. [7]

In particularly uneven terrain, the procedure described above would have been prevented by the presence of a large number of obstacles. There was, therefore, a second procedure known as "thread the needle", which consisted of proceeding between two obstacles along the bisector between them, providing they were sufficiently spaced to allow the rover to pass. If the rover had encountered a clearing before reaching a predetermined distance, it would have had to rotate on itself to calculate a new straight trajectory to reach the target. Conversely, the rover would have had to go back and try a different trajectory. As a last resort, contact sensors were mounted on the front and rear surfaces of the rover. [56]

To facilitate the rover's direction, an appropriate on-the-spot rotation could be commanded from Earth. The command was "Turn" and was performed using a gyroscope. [7] Three accelerometers measured the acceleration of gravity along three perpendicular directions, making it possible to measure the surface's slope. The rover was programmed to deviate from routes that would require a slope greater than 30°, [56] though it was designed not to tip over when tilted at 45°. [7] The distance traveled was determined by the number of revolutions of the wheels. [56]

Marie Curie

Marie Curie in the museum (see also from other angles: 1, 2, 3) Marie Curie Mars Rover 01.jpg
Marie Curie in the museum (see also from other angles: 1, 2, 3)

Marie Curie is a flight spare for the Sojourner. During the operational phase on Mars, the sequences of the most complex commands to be sent to Sojourner were verified on this identical rover at JPL. [57] NASA planned to send Marie Curie on the canceled Mars Surveyor 2001 mission; it was suggested to send it in 2003, proposing Marie Curie to be deployed "using a robotic-arm attached to the lander". [58] Rather than this, the Mars Exploration Rover program was launched in 2003. In 2015, JPL transferred Marie Curie to the Smithsonian National Air and Space Museum (NASM). [59]

According to space historian and NASM curator Matt Shindell:

The Marie Curie rover was a fully operational unit, I’m not sure at what point it was decided which was going to fly and which one would stay home, but it was ready to replace the main unit at a moment’s notice. [60]

Mars Yard

Sojourner at the Mars Yard test area (see also test rover at the Yard) JPL Mars Yard.jpg
Sojourner at the Mars Yard test area (see also test rover at the Yard)

To test robotic prototypes and applications under natural lighting conditions, JPL built a simulated Martian landscape called "Mars Yard". The test area measured 21 by 22 m (69 by 72 ft) and had a variety of terrain arrangements to support multiple test conditions. The soil was a combination of beach sand, decomposed granite, brick dust, and volcanic cinders. The rocks were several types of basalts, including fine-grained and vesicular in both red and black. Rock-size distributions were selected to match those seen on Mars and the soil characteristics matched those found in some Martian regions. Large rocks were not Mars-like in composition, being less dense and easier to move for testing. Other obstacles such as bricks and trenches were often used for specialized testing. [61] Mars Yard was expanded in 1998 and then in 2007 to support other Mars rover missions. [62]

Naming

Sojourner Truth SojournerTruth 1850 OliveGilbert.PNG
Sojourner Truth

The name "Sojourner" was chosen for the rover through a competition held in March 1994 by the Planetary Society in collaboration with JPL; it ran for one year and was open to students of 18 years and below from any country. Participants were invited to choose a "heroine to whom to dedicate the rover" and to write an essay about her accomplishments, and how these accomplishments could be applied to the Martian environment. [63] The initiative was publicized in the United States through the January 1995 edition of the magazine Science and Children published by the National Science Teachers Association. [63]

Some 3,500 papers were received from countries including Canada, India, Israel, Japan, Mexico, Poland, Russia, and the United States, of which 1,700 were from students aged between 5 and 18. The winners were chosen on the basis of the quality and creativity of the work, the appropriateness of the name for a Martian rover, and the competitor's knowledge of the heroine and the probe mission. [63] The winning paper was written by 12-year-old Valerie Ambroise of Bridgeport, Connecticut, who suggested dedicating the rover to Sojourner Truth, [64] a Civil War era African-American abolitionist and women's rights advocate. [63] The second place went to Deepti Rohatgi, 18, of Rockville, Maryland, who proposed Marie Curie, a Nobel Prize-winning Franco-Polish chemist. Third place went to Adam Sheedy, 16, of Round Rock, Texas, who chose Judith Resnik, a United States astronaut and Space Shuttle crew member who died in the 1986 Challenger disaster. [63] The rover was also known as Microrover Flight Experiment abbreviated MFEX. [43]

Operations

Position of the rover on the lander after opening of the petals. Mars Pathfinder opens after landing.gif
Position of the rover on the lander after opening of the petals.

Sojourner was launched on December 4, 1996, aboard a Delta II booster, and reached Mars on July 4, 1997. It operated in Ares Vallis channel in the Chryse Planitia of the Oxia Palus quadrangle, [65] from July 5 [66] to September 27, 1997, when the lander cut off communications with Earth. [65] In the 83 sols of activity—twelve times the expected duration for the rover—Sojourner traveled 104 m (341 ft), always remaining within 12 m (39 ft) of the lander. [49] It collected 550 images, [65] performed 16 analyzes through the APXS—nine of rocks and the remainder of the soil— [49] and performed 11 Wheel Abrasion Experiments and 14 experiments on soil mechanics in cooperation with the lander. [7] [67]

Landing site

The landing site for the rover was chosen in April 1994 at the Lunar and Planetary Institute in Houston. The landing site is an ancient flood plain called Ares Vallis, which is located in Mars' northern hemisphere and is one of the rockiest parts of Mars. It was chosen because it was thought to be a relatively safe surface on which to land and one that contains a wide variety of rocks that were deposited during a flood. This area was well-known, having been photographed by the Viking mission. [68] [69] [70] After a successful landing, the lander was officially named "The Carl Sagan Memorial Station" in honor of the astronomer. [71]

Deployment

Mars Pathfinder landed on July 4, 1997. The petals were deployed 87 minutes later with Sojourner rover and the solar panels attached on the inside. The rover exited the lander on the next day. [15]

Rock analysis

Overhead view of the area surrounding the lander illustrating the rover traverse. Red rectangles are rover positions at the end of sols 1-30. Locations of soil mechanics and wheel abrasion experiments, and APXS measurements are shown. PIA01151.jpg
Overhead view of the area surrounding the lander illustrating the rover traverse. Red rectangles are rover positions at the end of sols 1–30. Locations of soil mechanics and wheel abrasion experiments, and APXS measurements are shown.

The rocks at the landing site were given names of cartoon characters. Among them were Pop Tart, Ender, mini-Matterhorn, Wedge, Baker's Bench, Scooby Doo, Yogi, Barnacle Bill, Pooh Bear, Piglet, the Lamb, the Shark, Ginger, Souffle, Casper, Moe, and Stimpy. A dune was called Mermaid Dune, and a pair of hills were named Twin Peaks. [72] [73] [74]

The first analysis was carried out on the rock called "Barnacle Bill" during the third sol. The rock's composition was determined by the APXS spectrometer, which took 10 hours for a complete scan. The rock "Yogi" was analyzed on the 10th sol. [66] [75] It has been suggested the conformation of the land close to the rock, even visually at a lower level than the surrounding surface, was derived from the evaporation of floodwater. [76]

Both rocks turned out to be andesites; this finding surprised some scholars because andesites are formed by geological processes that require an interaction between materials of the crust and the mantle. A lack of information on the surrounding highlands made it impossible to grasp all of the implications of the discovery. [77]

The rover was then directed to the next target and on the 14th sol, it analyzed the rock named "Scooby-Doo" and imaged the "Casper" rock. [66] Both were deemed to be consolidated deposits. [52] The rock called "Moe" showed evidence of wind erosion. Most of the rocks analyzed showed a high silicon content. In a region nicknamed "Rock Garden", the rover encountered crescent-moon-shaped dunes that are similar to dunes on earth. [74]

The landing site is rich in varied rocks, some of which are clearly volcanic in origin, such as "Yogi"; others are conglomerates, the origins of which are the subject of several proposals. In one hypothesis, they formed in the presence of water in Mars' distant past. [52] In support of this, high silicon contents would be detected. This could also be a consequence of sedimentation processes; rounded rocks of various sizes were discovered and the valley's shapes are compatible with a river channel environment. [10] Smaller, more rounded stones may also have been generated during a surface impact event. [52]

When the mission's final results were described in a series of articles in the journal Science (December 5, 1997), it was believed the rock Yogi had a coating of dust but was similar to the rock Barnacle Bill. Calculations suggested both rocks mostly contain orthopyroxene (magnesium-iron silicate), feldspars (aluminum silicates of potassium, sodium, and calcium), and quartz (silicon dioxide) with smaller amounts of magnetite, ilmenite, iron sulfide, and calcium phosphate. [78] [79]

PIA01153.jpg
Annotated panorama of rocks near the rover (December 5, 1997)
Screenshot from The Martian, depicting the protagonist Mark Watney with Pathfinder lander and Sojourner rover. The Martian scene with Mars Pathfinder.jpg
Screenshot from The Martian , depicting the protagonist Mark Watney with Pathfinder lander and Sojourner rover.

Awards and honors

Key personnel

The development of the rover and its instruments as well as its guidance during operations on Mars were done by a group of engineers from NASA, collectively referred to as "The Rover Team". The key personnel were: [13]

PIA01466.jpg
Mars Pathfinder panorama of landing site taken by lander's camera (IMP)
Mars Pathfinder Presidential Panorama.jpg
Various images of the Sojourner shot by the lander have been composited into the 360 degree Presidential Panorama. Since the camera's position was consistent, it is thus possible to see these images of the rover in the context of the entire landscape. This provides a visual scale for understanding the sizes and distances of rocks surrounding the lander as well as a record of the travels of the rover. Several of the rover images were captured in full color. The rest were colorized using color sampled from those frames. [88]

Comparison to later Mars rovers

Two spacecraft engineers stand with a group of vehicles providing a comparison of three generations of Mars rovers developed at NASA's Jet Propulsion Laboratory. The setting is JPL's Mars Yard testing area. Front and center is the flight spare for the first Mars rover, Sojourner, which landed on Mars in 1997 as part of the Mars Pathfinder Project. On the left is a Mars Exploration Rover Project (MER) test rover that is a working sibling to Spirit and Opportunity, which landed on Mars in 2004. On the right is a Mars Science Laboratory test rover the size of that project's Mars rover, Curiosity, which landed on Mars in 2012. Sojourner and its flight spare, Marie Curie, are 65 cm long. The MER's rovers are 1.6 m long. The Curiosity rover is 3 m long. PIA15279 3rovers-stand D2011 1215 D521.jpg
Two spacecraft engineers stand with a group of vehicles providing a comparison of three generations of Mars rovers developed at NASA's Jet Propulsion Laboratory. The setting is JPL's Mars Yard testing area. Front and center is the flight spare for the first Mars rover, Sojourner, which landed on Mars in 1997 as part of the Mars Pathfinder Project. On the left is a Mars Exploration Rover Project (MER) test rover that is a working sibling to Spirit and Opportunity , which landed on Mars in 2004. On the right is a Mars Science Laboratory test rover the size of that project's Mars rover, Curiosity , which landed on Mars in 2012. Sojourner and its flight spare, Marie Curie, are 65 cm long. The MER's rovers are 1.6 m long. The Curiosity rover is 3 m long.

Sojourner's location in context

(view * discuss) Interactive image map of the global topography of Mars, overlaid with the position of Martian rovers and landers. Coloring of the base map indicates relative elevations of Martian surface. Clickable image: Clicking on the labels will open a new article. ( .mw-parser-output .legend{page-break-inside:avoid;break-inside:avoid-column}.mw-parser-output .legend-color{display:inline-block;min-width:1.25em;height:1.25em;line-height:1.25;margin:1px 0;text-align:center;border:1px solid black;background-color:transparent;color:black}.mw-parser-output .legend-text{} Active * Inactive * Planned) (See also: Mars map; Mars Memorials list) Mars Map.JPG
Interactive image map of the global topography of Mars, overlaid with the position of Martian rovers and landers. Coloring of the base map indicates relative elevations of Martian surface.
Mano cursor.svg Clickable image:Clicking on the labels will open a new article.
(  Active •   Inactive •   Planned)
PhoenixIcon.png Beagle 2
CuriosityIcon.png
Curiosity
PhoenixIcon.png
Deep Space 2
PhoenixIcon.png InSight
Mars3landericon.jpg Mars 2
Mars3landericon.jpg Mars 3
Mars3landericon.jpg Mars 6
PhoenixIcon.png
Mars Polar Lander ↓
RoverIcon.png Opportunity
CuriosityIcon.png
Perseverance
PhoenixIcon.png Phoenix
RoverIcon.png Rosalind Franklin
EDMIcon.png
Schiaparelli EDM
SojournerIcon.png Sojourner
RoverIcon.png
Spirit
ZhurongIcon.jpg Zhurong
VikingIcon.png
Viking 1
VikingIcon.png Viking 2

See also

Footnotes

  1. ↑ It was foreseen the possibility that three false positives out of twenty detections carried out before proceeding
  2. ↑ Image was taken by IMP before the mast was deployed. It was called "insurance panorama", because if something went wrong during deployment, the team would still have a panorama of the landing site. Once the mast was deployed the height of the IMP was constant. [20]

Related Research Articles

<i>Viking 2</i> Space orbiter and lander sent to Mars

The Viking 2 mission was part of the American Viking program to Mars, and consisted of an orbiter and a lander essentially identical to that of the Viking 1 mission. Viking 2 was operational on Mars for 1281 sols. The Viking 2 lander operated on the surface for 1,316 days, or 1281 sols, and was turned off on April 12, 1980, when its batteries eventually failed. The orbiter worked until July 25, 1978, returning almost 16,000 images in 706 orbits around Mars.

<i>Mars Pathfinder</i> Mission including first robotic rover to operate on Mars (1997)

Mars Pathfinder was an American robotic spacecraft that landed a base station with a roving probe on Mars in 1997. It consisted of a lander, renamed the Carl Sagan Memorial Station, and a lightweight, 10.6 kg (23 lb) wheeled robotic Mars rover named Sojourner, the first rover to operate outside the Earth–Moon system.

<span class="mw-page-title-main">Mars Exploration Rover</span> NASA mission to explore Mars via two rovers

NASA's Mars Exploration Rover (MER) mission was a robotic space mission involving two Mars rovers, Spirit and Opportunity, exploring the planet Mars. It began in 2003 with the launch of the two rovers to explore the Martian surface and geology; both landed on Mars at separate locations in January 2004. Both rovers far outlived their planned missions of 90 Martian solar days: MER-A Spirit was active until March 22, 2010, while MER-B Opportunity was active until June 10, 2018.

<i>Spirit</i> (rover) NASA Mars rover, active from 2004 to 2010

Spirit, also known as MER-A or MER-2, is a Mars robotic rover, active from 2004 to 2010. Spirit was operational on Mars for 2208 sols or 3.3 Martian years. It was one of two rovers of NASA's Mars Exploration Rover Mission managed by the Jet Propulsion Laboratory (JPL). Spirit landed successfully within the impact crater Gusev on Mars at 04:35 Ground UTC on January 4, 2004, three weeks before its twin, Opportunity (MER-B), which landed on the other side of the planet. Its name was chosen through a NASA-sponsored student essay competition. The rover got stuck in a "sand trap" in late 2009 at an angle that hampered recharging of its batteries; its last communication with Earth was on March 22, 2010.

<i>Opportunity</i> (rover) NASA Mars rover deployed in 2004

Opportunity, also known as MER-B or MER-1, and nicknamed Oppy, is a robotic rover that was active on Mars from 2004 until 2018. Opportunity was operational on Mars for 5111 sols. Launched on July 7, 2003, as part of NASA's Mars Exploration Rover program, it landed in Meridiani Planum on January 25, 2004, three weeks after its twin, Spirit (MER-A), touched down on the other side of the planet. With a planned 90-sol duration of activity, Spirit functioned until it got stuck in 2009 and ceased communications in 2010, while Opportunity was able to stay operational for 5111 sols after landing, maintaining its power and key systems through continual recharging of its batteries using solar power, and hibernating during events such as dust storms to save power. This careful operation allowed Opportunity to operate for 57 times its designed lifespan, exceeding the initial plan by 14 years, 47 days. By June 10, 2018, when it last contacted NASA, the rover had traveled a distance of 45.16 kilometers.

<span class="mw-page-title-main">Mars rover</span> Robotic vehicle for Mars surface exploration

A Mars rover is a remote-controlled motor vehicle designed to travel on the surface of Mars. Rovers have several advantages over stationary landers: they examine more territory, they can be directed to interesting features, they can place themselves in sunny positions to weather winter months, and they can advance the knowledge of how to perform very remote robotic vehicle control. They serve a different purpose than orbital spacecraft like Mars Reconnaissance Orbiter. A more recent development is the Mars helicopter.

<span class="mw-page-title-main">Exploration of Mars</span>

The planet Mars has been explored remotely by spacecraft. Probes sent from Earth, beginning in the late 20th century, have yielded a large increase in knowledge about the Martian system, focused primarily on understanding its geology and habitability potential. Engineering interplanetary journeys is complicated and the exploration of Mars has experienced a high failure rate, especially the early attempts. Roughly sixty percent of all spacecraft destined for Mars failed before completing their missions, with some failing before their observations could begin. Some missions have been met with unexpected success, such as the twin Mars Exploration Rovers, Spirit and Opportunity, which operated for years beyond their specification.

<span class="mw-page-title-main">Mars Science Laboratory</span> Robotic mission that deployed the Curiosity rover to Mars in 2012

Mars Science Laboratory (MSL) is a robotic space probe mission to Mars launched by NASA on November 26, 2011, which successfully landed Curiosity, a Mars rover, in Gale Crater on August 6, 2012. The overall objectives include investigating Mars' habitability, studying its climate and geology, and collecting data for a human mission to Mars. The rover carries a variety of scientific instruments designed by an international team.

<span class="mw-page-title-main">Alpha particle X-ray spectrometer</span>

An alpha particle X-ray spectrometer (APXS) is a spectrometer that analyses the chemical element composition of a sample from scattered alpha particles and fluorescent X-rays after a sample is irradiated with alpha particles and X-rays from radioactive sources. This method of analysing the elemental composition of a sample is most often used on space missions, which require low weight, small size, and minimal power consumption. Other methods are faster, and do not require the use of radioactive materials, but require larger equipment with greater power requirements. A variation is the alpha proton X-ray spectrometer, such as on the Pathfinder mission, which also detects protons.

<span class="mw-page-title-main">Mars landing</span> Landing of a spacecraft on the surface of Mars

A Mars landing is a landing of a spacecraft on the surface of Mars. Of multiple attempted Mars landings by robotic, uncrewed spacecraft, ten have had successful soft landings. There have also been studies for a possible human mission to Mars including a landing, but none have been attempted.

MESUR, the Mars Environmental SURvey was a NASA program designed to explore the planet Mars in preparation for human follow-up missions of the Space Exploration Initiative. The only mission of the program that was completed was MESUR Pathfinder.

The embedded computer systems onboard Mars rovers are designed to withstand high radiation levels and large temperature changes in space. For this reason their computational resources are limited compared to systems commonly used on Earth.

<span class="mw-page-title-main">InSight</span> NASA Mars lander (2018–2022)

The Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) mission was a robotic lander designed to study the deep interior of the planet Mars. It was manufactured by Lockheed Martin Space, was managed by NASA's Jet Propulsion Laboratory (JPL), and two of its three scientific instruments were built by European agencies. The mission launched on 5 May 2018 at 11:05:01 UTC aboard an Atlas V-401 launch vehicle and successfully landed at Elysium Planitia on Mars on 26 November 2018 at 19:52:59 UTC. InSight was active on Mars for 1440 sols.

<span class="mw-page-title-main">Materials Adherence Experiment</span> 1997 science experiment conducted on Mars

The Materials Adherence Experiment (MAE) was a material science experiment conducted between July 4, 1997, and August 12, 1997, during NASA's Mars Pathfinder mission. This was a joint experiment between NASA and the Jet Propulsion Laboratory at the California Institute of Technology that consisted of a small module mounted to Pathfinder's rover Sojourner that examined the effects of Martian surface dust on solar cells.

<i>Curiosity</i> (rover) NASA robotic rover exploring Gale crater on Mars

Curiosity is a car-sized Mars rover exploring Gale crater and Mount Sharp on Mars as part of NASA's Mars Science Laboratory (MSL) mission. Curiosity was launched from Cape Canaveral (CCAFS) on November 26, 2011, at 15:02:00 UTC and landed on Aeolis Palus inside Gale crater on Mars on August 6, 2012, 05:17:57 UTC. The Bradbury Landing site was less than 2.4 km (1.5 mi) from the center of the rover's touchdown target after a 560 million km (350 million mi) journey.

Timeline of <i>Opportunity</i> Robotic rover that was active on the planet Mars from 2004 to 2018

Opportunity is a robotic rover that was active on the planet Mars from 2004 to 2018. Launched on July 7, 2003, Opportunity landed on Mars' Meridiani Planum on January 25, 2004, at 05:05 Ground UTC, three weeks after its twin Spirit (MER-A), also part of NASA's Mars Exploration Rover Mission, touched down on the other side of the planet. While Spirit became immobile in 2009, and ceased communications in 2010, Opportunity exceeded its planned 90 sol duration of activity by 14 years 46 days. Opportunity continued to move, gather scientific observations, and report back to Earth until 2018. What follows is a summary of events during its continuing mission.

<i>Perseverance</i> (rover) NASA Mars rover deployed in 2021

Perseverance, is a car-sized Mars rover designed to explore the Jezero crater on Mars as part of NASA's Mars 2020 mission. It was manufactured by the Jet Propulsion Laboratory and launched on July 30, 2020, at 11:50 UTC. Confirmation that the rover successfully landed on Mars was received on February 18, 2021, at 20:55 UTC. As of 21 December 2024, Perseverance has been active on Mars for 1364 sols since its landing. Following the rover's arrival, NASA named the landing site Octavia E. Butler Landing.

<span class="mw-page-title-main">Timeline of Mars 2020</span> Event timeline of the NASA Mars 2020 mission

The Mars 2020 mission, consisting of the rover Perseverance and helicopter Ingenuity, was launched on July 30, 2020, and landed in Jezero crater on Mars on February 18, 2021. As of December 18, 2024, Perseverance has been on the planet for 1361 sols. Ingenuity operated for 1042 sols until its rotor blades, possibly all four, were damaged during the landing of flight 72 on January 18, 2024, causing NASA to retire the craft.

References

  1. ↑ Siddiqi, Asif A. (2018). Beyond Earth: A Chronicle of Deep Space Exploration, 1958–2016 (PDF). The NASA history series (second ed.). Washington, DC: NASA History Program Office. p. 195. ISBN   978-1-62683-042-4. LCCN   2017059404. SP2018-4041. Archived (PDF) from the original on 2019-12-08. Retrieved 2019-11-04.
  2. 1 2 3 4 5 "Mars Pathfinder FAQs – Sojourner". mars.nasa.gov. Archived from the original on 2020-05-24. Retrieved 2021-08-15.
  3. ↑ "Mars Pathfinder – Mars – Sol 86 Images". mars.nasa.gov. Archived from the original on 2020-10-26. Retrieved 2021-08-15.
  4. ↑ "Mars Pathfinder – Mars – Sol 92 Images". mars.nasa.gov. Archived from the original on 2021-03-22. Retrieved 2021-03-08.
  5. 1 2 "Sojourner". Archived from the original on 20 March 2015.
  6. ↑ "Mars Pathfinder – Mars – Sol 89 Images". mars.nasa.gov. Archived from the original on 2020-08-14. Retrieved 2021-08-15.
  7. 1 2 3 4 5 6 7 8 Matijevic, J. (1997). "Sojourner The Mars Pathfinder Microrover Flight Experiment". NASA. hdl:2014/21704. Archived from the original on 13 September 2021. Retrieved 2 October 2010.
  8. ↑ "Mars Pathfinder Rover". NASA. Archived from the original on 2020-10-21. Retrieved 2020-09-30.
  9. 1 2 Golombek, M.P.; Cook, R.A.; Moore, H.J.; Parker, T.J. (1997). "Selection of the Mars Pathfinder landing site". J. Geophys. Res. 102 (E2): 3967–3988. Bibcode:1997JGR...102.3967G. doi: 10.1029/96JE03318 .
  10. 1 2 Golombek, M.P. (1997). "Overview of the Mars Pathfinder Mission and Assessment of Landing Site Predictions". Science. 278 (5344): 1743–1748. Bibcode:1997Sci...278.1743G. doi: 10.1126/science.278.5344.1743 . PMID   9388167.
  11. 1 2 3 4 NASA, JPL (ed.). "Mars Pathfinder". Archived (PDF) from the original on 13 May 2013. Retrieved 24 September 2010.
  12. 1 2 JPL, NASA (ed.). "Rover Sojourner". Archived from the original on 25 October 2011. Retrieved 24 September 2010.
  13. 1 2 3 4 Tillman, J E. "JPL Mars Pathfinder Quick Facts". washington.edu. University of Washington. Archived from the original on August 19, 2021. Retrieved August 19, 2021.
  14. 1 2 3 4 5 Smith, Peter H. "Mars Pathfinder PIP (Continued – Part 2/3)". science.ksc.nasa.gov. Archived from the original on 20 August 2021. Retrieved 20 August 2021.PD-icon.svg This article incorporates text from this source, which is in the public domain .
  15. 1 2 "NASA – NSSDCA – Spacecraft – Details". nssdc.gsfc.nasa.gov. Archived from the original on January 27, 2021. Retrieved February 16, 2021.
  16. ↑ Smith, P. H.; Tomasko, M. G.; Britt, D.; Crowe, D. G.; Reid, R.; Keller, H. U.; Thomas, N.; Gliem, F.; Rueffer, P.; Sullivan, R.; Greeley, R.; Knudsen, J. M.; Madsen, M. B.; Gunnlaugsson, H. P.; Hviid, S. F.; Goetz, W.; Soderblom, L. A.; Gaddis, L.; Kirk, R. (1997). "The imager for Mars Pathfinder experiment". Journal of Geophysical Research . 102 (E2): 4003–4026. Bibcode:1997JGR...102.4003S. doi: 10.1029/96JE03568 .
  17. ↑ Smith P. H.; Bell J. F.; Bridges N. T. (1997). "Results from the Mars Pathfinder camera". Science . 278 (5344): 1758–1765. Bibcode:1997Sci...278.1758S. doi: 10.1126/science.278.5344.1758 . PMID   9388170.
  18. ↑ Schofield J. T.; Barnes J. R.; Crisp D.; Haberle R. M.; Larsen S.; Magalhaes J. A.; Murphy J. R.; Seiff A.; Wilson G. (1997). "The Mars Pathfinder atmospheric structure investigation meteorology (ASI/MET) experiment". Science. 278 (5344): 1752–1758. Bibcode:1997Sci...278.1752S. doi: 10.1126/science.278.5344.1752 . PMID   9388169.
  19. ↑ "Windsocks on Mars". JPL/NASA Mars Pathfinder. 2005. Archived from the original on March 5, 2016. Retrieved June 10, 2015.
  20. 1 2 "How does the IMP works?". mars.nasa.gov. NASA. Archived from the original on 5 April 2021. Retrieved 25 August 2021.
  21. ↑ Smith, P. H. (February 25, 1997). "The imager for Mars Pathfinder experiment". Journal of Geophysical Research. 102 (2): 4003–4025. Bibcode:1997JGR...102.4003S. doi: 10.1029/96JE03568 .
  22. 1 2 "Description of the Rover Sojourner". mars.nasa.gov. Archived from the original on 2020-09-19. Retrieved 2021-08-15.
  23. 1 2 "Mars Pathfinder Microrover". mars.nasa.gov. Archived from the original on 2020-10-26. Retrieved 2021-08-15.
  24. 1 2 "The real Mars lander in 'The Martian': Fact checking the film's NASA probe". collectspace.com. collectSPACE . Retrieved 15 August 2021.
  25. 1 2 3 4 5 6 Bickler, D. (1997). JPL, NASA (ed.). The Mars Rover Mobility System (PDF). Archived from the original (PDF) on 26 May 2010. Retrieved 25 September 2010.
  26. 1 2 3 4 5 Lindemann, R.A.; C.J. Voorhees (2005). Jet Propulsion Laboratory, National Aeronautics and Space Administration (ed.). "Mars Exploration Rover Mobility Assembly Design, Test and Performance" (PDF). 2005 International Conference on Systems, Man, and Cybernetics, Hawaii, October 10–12, 2005. Pasadena, CA. Archived from the original (PDF) on 26 May 2010. Retrieved 25 September 2010.
  27. 1 2 Morgan, M.; D. Bickler (2000). "The retelling of "Romancing the rover (how Sojourner came to be in the late 1980s and its journey to Mars)"" (PDF). JPL. Archived from the original (PDF) on 27 May 2010. Retrieved 25 September 2010.
  28. ↑ US 4840394,Donald B. Bickler,"Articulated suspension system",published 1988-04-21,issued 1989-06-20, assigned to NASA
  29. ↑ Bickler, Donald (April 1998). "Roving over Mars". Mechanical Engineering. pp. 74–77. Archived from the original on 2008-10-22.
  30. ↑ Young, A. (2007). Springer (ed.). Lunar and planetary rovers: the wheels of Apollo and the quest for Mars 2007. Springer. pp. 212–223. ISBN   978-0-387-30774-9. Archived from the original on 13 September 2021. Retrieved 26 February 2011.
  31. ↑ Bajracharya, Max; Maimone, Mark W.; Helmick, Daniel (December 2008). "Autonomy for Mars rovers: past, present, and future" (PDF). Computer . 41 (12). IEEE Computer Society: 44–50. doi:10.1109/MC.2008.479. ISSN   0018-9162. S2CID   9666797. Archived (PDF) from the original on March 4, 2016. Retrieved June 10, 2015.
  32. ↑ Stone, H. W. (1996). Mars Pathfinder Microrover: A Small, Low-Cost, Low-Power Spacecraft (Report). Jet Propulsion Laboratory. hdl:2014/25424. Archived from the original on 2021-09-13. Retrieved 2021-08-14.
  33. ↑ "Rover Thermal Design". mars.nasa.gov. NASA. Archived from the original on 14 August 2021. Retrieved 14 August 2021.
  34. ↑ ""QUESTION: What type of computer is the Pathfinder utilizing? ..." (NASA Quest Q&A)". NASA. 1997. Archived from the original on March 7, 2016. Retrieved July 21, 2015.
  35. ↑ ""QUESTION: When it was designed, why was only a single 80C85 CPU used? ..." (NASA Quest Q&A)". NASA. 1997. Archived from the original on July 23, 2015. Retrieved July 21, 2015.
  36. ↑ "Wind River Powers Mars Exploration Rovers—Continues Legacy as Technology Provider for NASA's Space Exploration". Wind River Systems. June 6, 2003. Archived from the original on January 6, 2010. Retrieved August 28, 2009.
  37. ↑ Parallel sparking: Many chips make light work, Douglas Heaven, New Scientist magazine, issue 2930, August 19, 2013, p44. Online (by subscription) Archived October 6, 2014, at the Wayback Machine
  38. ↑ Reeves, Glenn E. (December 15, 1997). "What really happened on Mars? – Authoritative Account". Microsoft.com. Archived from the original on June 11, 2015. Retrieved June 10, 2015.
  39. ↑ Jones, Michael B. (December 16, 1997). "What really happened on Mars?". Microsoft.com. Archived from the original on June 12, 2015. Retrieved June 10, 2015.
  40. ↑ "The Mars Pathfinder Mission Status Reports — Second Week". Office of the Flight Operations Manager – Mars Pathfinder Project. Archived from the original on January 4, 2016. Retrieved October 24, 2015.
  41. ↑ "The Mars Pathfinder Mission Status Reports — Third Week". Office of the Flight Operations Manager – Mars Pathfinder Project. Archived from the original on April 10, 2016. Retrieved October 24, 2015.
  42. ↑ "How the Mars Microrover Radios and Antennas Work". mars.nasa.gov. Archived from the original on 2021-04-17. Retrieved 2021-08-15.
  43. 1 2 "Mars Pathfinder Microrover Ready to Roll!". mars.nasa.gov. Archived from the original on 2019-12-02. Retrieved 2021-08-15.
  44. 1 2 3 4 5 "Rover Camera Instrument Description". Archived from the original on 2017-01-18. Retrieved 2014-03-09.
  45. ↑ Cooper, Brian K. "MFEX: Microrover Flight Experiment – Rover Control Workstation". mars.nasa.gov. Archived from the original on 2021-08-14. Retrieved 2021-08-15.
  46. ↑ Mishkin, Andrew. "Making Tracks on Mars Mission Operations for Deep Space" (PDF). trs-new.jpl.nasa.gov. NASA, JPL. Archived from the original (PDF) on 2012-03-23. Retrieved 17 August 2021.
  47. ↑ R. Rieder; H. Wänke; T. Economou; A. Turkevich (1997). "Determination of the chemical composition of Martian soil and rocks:The alpha proton X ray spectrometer". Journal of Geophysical Research: Planets. 102 (E2): 4027–4044. Bibcode:1997JGR...102.4027R. doi: 10.1029/96JE03918 .
  48. 1 2 3 JPL, NASA (ed.). "Mars Pathfinder Instrument Descriptions". Archived from the original on 4 June 2011. Retrieved 3 October 2010.
  49. 1 2 3 4 5 Wänke, H.; J. Brückner; G. Dreibus; R. Rieder; I. Ryabchikov (2001). "Chemical Composition of Rocks and Soils at the Pathfinder Site". Space Science Reviews. 96: 317–330. Bibcode:2001SSRv...96..317W. doi:10.1023/A:1011961725645. S2CID   189767835.
  50. ↑ Rieder, R. (1997). "The Chemical Composition of Martian Soil and Rocks Returned by the Mobile Alpha Proton X-ray Spectrometer: Preliminary Results from the X-ray Mode". Science. 278 (5344): 1771–1774. Bibcode:1997Sci...278.1771R. doi: 10.1126/science.278.5344.1771 . PMID   9388173.
  51. 1 2 Blomquist, R.S. (1995). "The Alpha-Proton-X-ray Spectrometer Deployment Mechanism – An Anthropomorphic Approach to Sensor Placement on Martian Rocks and Soil". 29th Aerospace Mechanisms Symposium. NASA Johnson Space Center. 1995: 61. Bibcode:1995aeme.symp...61B. hdl:2014/33265. Archived from the original on 13 September 2021. Retrieved 11 October 2010.
  52. 1 2 3 4 5 The Rover Team (1997). "Characterization of the Martian Surface Deposits by the Mars Pathfinder Rover, Sojourner". Science. 278 (5344): 1765–1768. Bibcode:1997Sci...278.1765M. doi: 10.1126/science.278.5344.1765 .
  53. 1 2 3 4 D.C. Ferguson (1999). "Evidence for Martian electrostatic charging and abrasive wheel wear from the Wheel Abrasion Experiment on the Pathfinder Sojourner rover". J. Geophys. Res. 104 (E4): 8747–8789. Bibcode:1999JGR...104.8747F. doi:10.1029/98JE02249.
  54. 1 2 3 4 5 S.M. Stevenson (1997). NASA (ed.). Mars Pathfinder Rover—Lewis Research Center Technology Experiments Program. NASA Technical Memorandum 107449 (PDF). Archived from the original (PDF) on 10 October 2006. Retrieved 23 October 2010.
  55. 1 2 Landis, G.A. (1998). NASA (ed.). "Measuring Dust on Mars". Archived from the original on 11 September 2011. Retrieved 23 October 2010.
  56. 1 2 3 4 5 6 7 Matijevic, J. (1998). "Autonomous Navigation and the Sojourner Microrover". Science. 215. hdl:2014/19052. Archived from the original on 13 September 2021. Retrieved 1 October 2010.
  57. ↑ Laubach, S.L. (1999). California Institute of Technology (ed.). Theory and Experiments in Autonomous Sensor-Based Motion Planning with Applications for Flight Planetary Microrovers (phd). Pasadena, California: California Institute of Technology. p. 34. doi:10.7907/b1wv-hc78. Archived from the original on 23 September 2015. Retrieved 5 June 2011. pdf Archived 2021-04-30 at the Wayback Machine
  58. ↑ Mishkin, Andrew. "An automated rover command generation prototype for the Mars 2003 Marie Curie rover" (PDF). NASA. Archived from the original (PDF) on 2012-03-23. Retrieved 17 August 2021.
  59. ↑ "Rover, Marie Curie, Mars Pathfinder, Engineering Test Vehicle". National Air and Space Museum. Archived from the original on 13 August 2021. Retrieved 13 August 2021.
  60. ↑ Kindy, David. "Recalling the Thrill of Pathfinder's Mission to Mars". smithsonianmag.com. Smithsonian Magazine. Archived from the original on 14 August 2021. Retrieved 14 August 2021.
  61. ↑ "The MarsYard II". www-robotics.jpl.nasa.gov. NASA, JPL. Archived from the original on 21 August 2021. Retrieved 21 August 2021.PD-icon.svg This article incorporates text from this source, which is in the public domain .
  62. ↑ Kelly, Tiffany. "JPL engineers test out their rovers on a fake Red Planet". mcall.com. The Morning Call. Archived from the original on 2021-08-21. Retrieved 2021-08-21.
  63. 1 2 3 4 5 NASA (ed.). "NASA Names First Rover to Explore the Surface of Mars". Archived from the original on 7 June 2011. Retrieved 24 September 2010.
  64. ↑ "Girl Who Named Mars Rover Stays Down to Earth". The New York Times. 1997-07-14. ISSN   0362-4331. Archived from the original on 2020-10-26. Retrieved 2019-01-24.
  65. 1 2 3 NASA (ed.). "Mars Pathfinder". Mars Exploration Program. Archived from the original on 13 April 2005. Retrieved 23 November 2010.
  66. 1 2 3 JPL, NASA (ed.). "Summary of Rover Operations". Mars Pathfinder Mission. Archived from the original on 25 October 2011. Retrieved 24 September 2010.
  67. ↑ "Summary of Rover Activity". NASA. Archived from the original on 25 October 2011. Retrieved 23 November 2010.
  68. ↑ "Mars Pathfinder Science Results". NASA. Archived from the original on September 20, 2008. Retrieved June 9, 2008.
  69. ↑ "Mars Pathfinder Landing Site". lpi.usra.edu. Lunar and Planetary Institute. Archived from the original on 2 August 2010. Retrieved 17 August 2021.
  70. ↑ "Mars Pathfinder Landing Site". nssdc.gsfc.nasa.gov. NASA. Archived from the original on 23 April 2021. Retrieved 17 August 2021.
  71. ↑ "Mars lander renamed for Sagan". NASA. Archived from the original on December 11, 2018. Retrieved September 5, 2017.
  72. ↑ "Mars Pathfinder Black and White Images". nssdc.gsfc.nasa.gov. NASA. Archived from the original on 16 August 2021. Retrieved 16 August 2021.
  73. ↑ "Rocks explored by the Rover". windows2universe.org. Windows to the Universe. Archived from the original on 16 August 2021. Retrieved 16 August 2021.
  74. 1 2 "Mars Pathfinder Science Results: Geology". mars.nasa.gov. NASA. Archived from the original on 20 March 2021. Retrieved 16 August 2021.
  75. ↑ Montclair State University (1997). "'Yogi' Rock Found On Mars Similar To Rocks Underneath 'Yogi' Berra Stadium, Geologist Says". ScienceDaily. Archived from the original on 4 June 2011. Retrieved 7 June 2011.
  76. ↑ NASA, ed. (11 July 1997). "Yogi Rock". Astronomy Picture of the Day . Archived from the original on 19 June 2011. Retrieved 7 June 2011.
  77. ↑ Jet Propulsion Laboratory, NASA (ed.). "Mars Pathfinder Science Results: Mineralogy and Geochemistry". Archived from the original on 17 October 2011. Retrieved 15 December 2010.
  78. ↑ "APXS Composition Results". NASA. Archived from the original on June 3, 2016. Retrieved June 10, 2015.
  79. ↑ Bruckner, J.; Dreibus, G.; Rieder, R.; Wanke, H. (2001). "Revised Data of the Mars Pathfinder Alpha Proton X-ray spectrometer: Geochemical Behavior of Major and Minor Elements". Lunar and Planetary Science XXXII: 1293. Bibcode:2001LPI....32.1293B.
  80. ↑ Pfarrer, Chuck; Lemkin, Jonathan (2000). "Red Planet" Archived 2015-09-23 at the Wayback Machine (PDF). The Daily Script. p. 45. Retrieved December 10, 2015.
  81. ↑ IMDb.com (ed.). "Crazy credits for "Enterprise"". IMDb . Archived from the original on 12 February 2011. Retrieved 24 November 2010.
  82. ↑ Weir, Andy (2014). The Martian . New York: Crown Publishers. ISBN   978-0-8041-3902-1.
  83. ↑ "'The Martian' – Anatomy of a Scene w/ Director Ridley Scott". YouTube. The New York Times. 2 October 2015. Archived from the original on 13 August 2021. Retrieved 13 August 2021.
  84. ↑ "Division Activity at Recent Meetings" (PDF). Planetary Geology Division Newsletter. 16 (1): 1. 1997. Archived from the original (PDF) on June 8, 2011.
  85. ↑ "Mars Pathfinder Lands On U.S. Postage Stamp". mars.nasa.gov. NASA. Archived from the original on 19 March 2021. Retrieved 15 August 2021.
  86. ↑ Carnegie Mellon University (ed.). "The 2003 Inductees: Mars Pathfinder Sojourner Rover". Archived from the original on 7 October 2007. Retrieved 15 December 2010.
  87. ↑ Weitering, Hanneke (February 25, 2021). "NASA's Perseverance rover on Mars is carrying an adorable 'family portrait' of Martian rovers". Space.com . Archived from the original on July 14, 2021. Retrieved July 14, 2021.
  88. ↑ "Presidential Panorama". mars.nasa.gov. NASA. Archived from the original on 23 June 2021. Retrieved 30 August 2021.PD-icon.svg This article incorporates text from this source, which is in the public domain.

Some sections of this article were originally translated from the Italian Wikipedia article. For original, see it:Sojourner.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.