This article is part of a series on the |
Politics of India |
---|
Indiaportal |
Electronic voting is the standard means of conducting elections using Electronic Voting Machines (EVMs) in India. The system was developed for the Election Commission of India by state-owned Electronics Corporation of India and Bharat Electronics. Starting in the late 1990s, they were introduced in Indian elections in a phased manner.
Prior to the introduction of electronic voting, paper ballots were used and manual counting was done. The printed paper ballots were expensive, required substantial post-voting resources and time to count individual ballots and were prone to fraudulent voting with pre-filled fake ballots. Introduction of EVMs have brought down the costs significantly, reduces the time of counting to enable faster announcement of results and eliminated fraudulent practices due to safety features such as security locking, limits to rate of voting per minute and verification of thumb impressions. EVMs are stand-alone machines that use write once read many memory. They are self-contained, battery-powered and do not need any networking capability. They do not have any wireless or wired components that connect to the internet.
Various opposition parties at times have alleged faulty EVMs after they failed to defeat the incumbent. In 2011, the Supreme Court of India directed the Election Commission to include a paper trail to help confirm the reliable operation of EVMs. The Election Commission developed EVMs with voter-verified paper audit trail (VVPAT) which was trialed in the 2014 Indian general election. After the 2019 ruling by the Supreme Court, EVMs with accompanying VVPAT are used in all the elections with a small percentage (2%) of the VVPATs verified to ensure the reliability before certifying the final results.
The Election Commission of India has also claimed that the machines, system checks, safeguard procedures, and election protocols are tamper-proof. To mitigate any doubts regarding the hardware, prior to the election day, a sample number of votes for each political party nominee are entered into each machine, in the presence of polling agents and at the end of this sample trial run, the votes counted and matched with the entered sample votes, to ensure that the machine's hardware has not been tampered with, it is operating reliably and that there were no hidden votes pre-recorded in each machine.
Paper ballots were exclusively used during elections till the 1990s. [1] [2] With the paper ballots, substantial resources were required for printing, transportation, storage and counting of individual ballots. [3] Paper ballots were prone to fraudulent voting and booth capturing, where party loyalists captured booths and stuffed them with pre-filled fake ballots. [4] [5] Since the late 1950s, there were multiple documented cases of such activities being reported and the problem grew between the 1950s and 1980s, becoming a serious and large scale problem in certain states and regions often accompanied with violence. [6] [7] In the late 1970s, Election Commission of India sought a solution for the issues which resulted in the development of electronic voting machines (EVM). [5] [8]
The idea of using an Electronic Voting Machine (EVM) was proposed in 1977 and Electronics Corporation of India (ECIL) was tasked with the development of the same. A working model was evolved in 1979 and was showcased to various political parties in August 1980. [9] Bharat Electronics (BEL) and ECIL were tasked with manufacturing EVMs. [10] The EVMs were first trialed in May 1982 in the by-election to Paravur assembly constituency in Kerala in a limited number of polling stations. [11] [12] In a ruling on a case filed against the usage of EVMs in the by-election, the Supreme Court of India ruled that the Representation of People Act, 1951 and the Conduct of Election Rules, 1961 specified the usage of paper ballots and forbade the use of any new methods including electronic voting. The court stated the manner in which the orders were issued for the use of EVMs was unconstitutional and the usage of any alternate means would require to be specified under the law. By the time of the verdict, EVMs had been used in several other elections and the court did not rule on the results of those elections. [11]
Post the court ruling, as there was no provision explicitly permitting the usage of EVMs, it was not deployed immediately. [11] An amendment to the Representation of the People Act, 1951 which allowed the usage of EVMs, was passed by the Parliament of India in December 1988 and came into force in March 1989. [9] [13] In March 1992, changes were made to the Conduction of Election Rules, 1961 by the Government of India to permit the usage of electronic voting. [11] The deployment was delayed as general consensus could not be reached with the political parties and other stakeholders on the usage of EVMs. [9] In 1998, the machines were used on an experimental basis across 25 state assembly constituencies during the assembly elections in Rajasthan, Madhya Pradesh and Delhi. In May 2001, EVMs were used in all constituencies for the state assembly elections in Tamil Nadu, Kerala, Puducherry and West Bengal. In 2004, in the General Election, the EVMs were used in all 543 Parliamentary Constituencies for the first time. Since the time, all state assembly and parliamentary elections are held using the EVMs. [9] [13] [14]
As it was possible to know how many people from a polling station exactly voted for a candidate, there was a probability that a winning candidate might show favoritism or hold a grudge on specific areas depending on the votes received. In order to mitigate the issue, a totaliser was developed in 2008, which was connected to several EVM units and displayed only the overall results instead of votes from individual machines. [15] [16]
After a consultation with the political parties in 2010, the Election Commission appointed an expert technical committee to study the feasibility of a voter-verified paper audit trail (VVPAT) in EVMs as a measure of transparency. [17] The committee was tasked with examining the possibility of displaying a printed paper to a voter which consisted of the symbol of the party to which the vote was cast. [18] Based on the recommendation of the committee, a VVPAT system was developed and was put on field trials in 2011. [19] [20] In July 2011, trials were conducted at 175 polling booths in Ladakh, Thiruvananthapuram, Cherrapunjee, East Delhi and Jaisalmer to test the performance of the VVPAT system under various weather conditions. [21] [22]
VVPAT was further introduced on a trial basis in a by-poll at Noksen in Nagaland in September 2013. [23] [24] It was later used in various legislative elections and in eight Lok Sabha constituencies in 2014 Indian general election. [25] [26] [27] Following a directive of the Supreme Court on 8 October 2013, the Election Commission of India introduced VVPATs along with EVMs in a phased manner. [28] [29] In 2019, the Supreme Court further directed that a small percentage (2%) of the VVPATs to be verified to ensure the reliability before the final results were certified. [30] [31]
The EVM was designed by a team led by A.G. Rao and Ravi Poovaiah, professors at IIT Bombay. [32] An EVM consists of two units, a control unit, and the ballot unit which are connected by a cable. [33] [34] The ballot unit facilitates the actual voting by a voter and consists of a ballot paper screen with the names of candidates and their symbols alongside labeled buttons, indicator lights and Braille signage. The control unit is responsible for the operational control of the ballot units, stores the vote counts and displays the results on LED displays. The control unit is pre-programmed at the time of manufacturing and cannot be altered later. [34]
The machines are powered by a 7.5 volt battery inserted into the control unit. [9] [34] The designers intentionally opted for battery power, to prevent the possibility of power cables interfering with the functioning and the EVMs can function without a secondary power source. [35] The two units work in tandem and cannot work independently. The EVMs do not have any communication components or internet interface. The ballot unit has an internal clock and a pre-programmed protocol by which it records every input-output event with a timestamp provided it is powered. [34]
A single ballot unit can list a maximum of 16 candidates and as a part of the initial design, up to four ballot units could be connected in parallel to a single control unit to cater to a maximum of 64 candidates. After an upgrade in 2013, 24 ballot units can now be connected to a single unit so that it can cater to a maximum of 384 candidates. [9] [36] [37] A single machine can record a maximum of 2000 votes. [38] The devices were designed to prevent fraud by limiting the number of new votes can be entered into the machine in a given time frame. In a minute, the EVMs can register a maximum of five votes. [2] [5] The later version of the EVMs are all equipped with VVPAT capability. [39] VVPAT system which was an upgrade of the EVMs had modified software that allowed a printer to be attached to the machine. [40] In June 2018, a built-in-hood was added to protect the printer and other devices from excess light and heat in VVPAT systems. [41]
The EVMs are inventoried and stored at secure locations when not in use. They are tracked by the Election Commission of India on a real-time basis and distributed randomly to the polling booths. [42] [43] In 2017, the Election Commission decided to replace all first generation machines and most of the machines in use in 2024 belong to the third generation. [44] [45] Prior to the elections, the machines are randomly allocated to polling booths and sample checks are carried out to ensure working condition. Ballot papers are inserted into the displays in the ballot unit and test votes for each nominee is entered into the machine in the presence of polling agents and counted to match with the entered sample votes. [46] [42]
Before the voting, the control units are sealed. The control unit is operated by the polling booth officer, while the ballot unit is operated by the voter in privacy. The officer confirms the voter's identification before electronically activating the ballot unit to accept a new vote. Once the voter enters the vote, the ballot unit displays the vote to the voter and records it in its memory. Post the voting, the polling officer presses the close button and the control unit registers the polled votes. [34] [42] The units are identified by unique identifier numbers and the a particular control unit is designed to work with a specific ballot unit. [47] [48] Once the polling process is completed, the votes are recorded in the device's memory on the same order of polling and the device's ability to accept additional votes is disabled. [5] [49] The control unit can store the vote in its memory for more than ten years. [46] [50] With the VVPAT system, when a vote is cast, it is recorded in its memory and simultaneously a serial number and vote data is printed out for the voter to verify the same. [51] The Election Commission maintains a database of thumb impressions and signatures of the voters along with identification, which is matched in order to identify the eligibility of a voter and ensure that a voter cannot cast a ballot more than once. [5] [42]
After a poll closes on an election day, the Presiding officer will hand over an account of votes recorded in each machine to the polling agents of the political parties. [42] The units are separated and the control units moved and stored separately in locked and guarded premises. [42] [52] [53] At the time of counting of votes, the results are displayed on the control unit on pressing the "Result" button. [50] [54] The button cannot be pressed before the polling is closed by the polling officer-in-charge. It is usually hidden and is exposed only at the counting center in the presence of the designated officer. The total displayed will also be tallied with the count given on the polling day. [34] [42]
The manufacturing cost per EVM was ₹5,500 (equivalent to ₹59,000orUS$700 in 2023) for the first batch of machines that were purchased in 1989–90. The cost of the production of later models was estimated to be ₹8,670 (equivalent to ₹28,000orUS$330 in 2023) in 2006. [55] The cost was estimated to be ₹10,500 (equivalent to ₹17,000orUS$200 in 2023) per unit based on an additional order placed in 2014. [56] Though the design, production and procurement was capital intensive, it has helped reduce the cost incurred on the printing of ballot papers, their transportation and storage and the counting staff and the remuneration paid to them. [57] EVMs are easier to transport compared to ballot boxes as they are lighter, more portable, and come with polypropylene carrying cases. [34] As there are reduced probability of malfeasance and rejection of votes, it eliminates the requirement of re-polling due to these issues. [5] An independent study had also indicated that the voting by the economically weaker section have increased due to the ease of usage with EVMs. [58] The shelf life of an EVM is estimated to be 15 years. [38] [59]
The use of EVMs and questions of their reliability have been raised by academics and politicians. In February 2010, an international conference held under the chairmanship of Subramanian Swamy blamed the Election Commission for shirking from its responsibility on proving the transparency of EVMs. [60] In April 2010, an independent security analysis undertaken by Hari K. Prasad, Rop Gonggrijp, and Alex Halderman, found that the machines could be manipulated by people who have physical access to the machines. While manufacturing, people with access could insert malicious hardware and people with physical access between voting and counting could change vote totals or learn about the results earlier. It suggested moving to a voting system that provides greater transparency such as paper ballots, precinct count optical scan, or a voter verified paper audit trail for skeptical voters to observe the physical counting process to gain confidence that the outcome is fair. [49] In August 2010, one of the authors of the research was charged with suspected EVM theft. [61] A research from The Hindu shared similar concerns that the EVMs could be manipulated during manufacturing, storage during the non-election periods and service of the machines by authorised technicians. It further suggested the usage of paper trail for verification and the use of authentication units to check the devices for counterfeit or tampered units. [47]
In August 2017, EVMs from multiple countries were hacked by programmers at the EVM Hacking village at the 25th DEF CON conference held at Las Vegas. [62] [63] Indian made EVMs however, were not included as part of the event. [64] [65] In the same year, the Election Commission organized an open hackathon encouraging people to attempt hacking of EVMs used by the commission in various Indian elections. [66] While the Commission announced that no attempts were made to demonstrate any vulnerabilities in the event, the registered participants claimed that the Commission made only a few select machines available and imposed additional conditions. [67] In January 2019, a self proclaimed cyber expert based in London claimed that the results can be manipulated by using low frequency signals. The Election Commission however dismissed the allegations since the machines did not use wireless frequencies to communicate with other devices and no proof was provided by the expert to demonstrate the hacking of the devices. [68] [69]
The Election Commission and the manufacturers of the EVMs have consistently rejected the possibility of EVM tampering. [70] They have maintained that the machines are tamper-proof as the programming is done at a secure manufacturing facility. They have also contended that there is no connecting or transmission devices attached to the machines and the machines are securely stored with a real-time logging system in the machine detecting any access or attempts to change. [71] [72] [73] Concerns have also been raised on the software which could be tampered with during initial programming and could be programmed to register a particular button. The Commission responded that the buttons are interchangeable and the order of candidates is randomly selected. [74]
There have been multiple cases against the usage of EVMs before the state high courts and the Supreme Court of India. The courts have often dismissed these cases and ruled in the favor of the Election Commission and the Supreme Court has declared that the use of EVMs as constitutionally valid. [11] [13] [75] A PIL was filed in the Supreme Court in 2011 for directing the Election Commission to modify the EVMs to give a slip printed with the symbol of the party in whose favor the voter cast. [76] [77] [78] On 17 January 2012, Delhi High Court in its ruling on Subramanian Swamy's writ petition challenging the use of EVMs in the present form asked the Election Commission to hold wider consultations with the executive, political parties and other stakeholders on the matter. [79] Following further petitions in the Supreme Court and the subsequent ruling in 2013 led to the use of VVPATs. [80] [81] [82]
Nepal, Bhutan, Namibia and Kenya have acquired India-manufactured EVMs. [83] In 2013, the Election Commission of Namibia acquired 1700 control units and 3500 ballot units from Bharat Electronics Limited and these units were used in the regional and presidential elections in 2014. [84] [85] Several other Asian and African countries have also expressed interested in using the Indian made EVMs. [83]
A voting machine is a machine used to record votes in an election without paper. The first voting machines were mechanical but it is increasingly more common to use electronic voting machines. Traditionally, a voting machine has been defined by its mechanism, and whether the system tallies votes at each voting location, or centrally. Voting machines should not be confused with tabulating machines, which count votes done by paper ballot.
Electronic voting is voting that uses electronic means to either aid or take care of casting and counting ballots including voting time.
A polling place is where voters cast their ballots in elections. The phrase polling station is also used in American English and British English, although a polling place is the building and polling station is the specific room where voters cast their votes. A polling place can contain one or more polling stations. In Australian English, "polling place" is used. Americans also use the term voting precinct in some states.
An electronic voting machine is a voting machine based on electronics. Two main technologies exist: optical scanning and direct recording (DRE).
Vote counting is the process of counting votes in an election. It can be done manually or by machines. In the United States, the compilation of election returns and validation of the outcome that forms the basis of the official results is called canvassing.
Voter verifiable paper audit trail (VVPAT) or verified paper record (VPR) is a method of providing feedback to voters who use an electronic voting system. A VVPAT allows voters to verify that their vote was cast correctly, to detect possible election fraud or malfunction, and to provide a means to audit the stored electronic results. It contains the name and party affiliation of candidates for whom the vote has been cast. While VVPAT has gained in use in the United States compared with ballotless voting systems without it, hand-marked ballots are used by a greater proportion of jurisdictions.
India has a parliamentary system as defined by its constitution, with power distributed between the union government and the states. India's democracy is the largest democracy in the world.
Rule 49-O was a rule in The Conduct of Elections Rules, 1961 of India, which governs elections in the country. It described the procedure to be followed when a valid voter decides not to cast his vote, and decides to record this fact. The rule was declared by the Supreme Court in September 2013 to be incompatible with the constitution and the Election Commission of India announced that the option under this rule would not be available any more. The apparent purpose of this section was to maintain a proper record in order to prevent the election fraud or the misuse of votes.
Electronic voting by country varies and may include voting machines in polling places, centralized tallying of paper ballots, and internet voting. Many countries use centralized tallying. Some also use electronic voting machines in polling places. Very few use internet voting. Several countries have tried electronic approaches and stopped because of difficulties or concerns about security and reliability.
A general election was held on 15 October 2014 to elect 90 members of the Haryana Legislative Assembly. The term of previous assembly elected in 2009 was to expire on 27 October 2014. The results were announced on 19 October. The BJP won the majority in the Assembly. Manohar Lal Khattar was chosen to head the new government.
Banka is one of 243 constituencies of legislative assembly of Bihar. It is part of Banka Lok Sabha constituency along with other assembly constituencies viz. Amarpur, Katoria, Belhar and Dhoraiya. In 2015 Bihar Legislative Assembly election, Banka was one of the 36 seats to have VVPAT enabled electronic voting machines.
The Election Commission of India (ECI) is a constitutional body established by the Constitution of India empowered to conduct free and fair elections in India. The Election commission is headed by a Chief Election Commissioner and consists of two other Election Commissioners.
Noksen is one of the 60 Legislative Assembly constituencies of Nagaland state in India. It is part of Tuensang district and is reserved for candidates belonging to the Scheduled Tribes.
The election to the 17th Uttar Pradesh Legislative Assembly was held from 11 February to 8 March 2017 in 7 phases. This election saw a voter turnout of 61.11% compared to 59.40% in the previous election. The Bharatiya Janata Party (BJP) won the election by an overwhelming three-quarters majority of 325 seats despite not projecting a chief ministerial candidate before the election. As part of its election strategy, BJP contested under a collective leadership and capitalised mostly on the political clout and 'brand' of its leader Narendra Modi.
A Legislative Assembly election was held in Manipur on 4 March and 8 March 2017 to elect the 60 members of the Manipur Legislative Assembly. before the expiration of the term of the previous Assembly on 18 March 2017. The election was fought mainly on the issues of "territorial integrity of Manipur" and the Naga peace accord. The incumbent Indian National Congress lost majority, though it had plurality. The Bharatiya Janata Party, which won 21 seats, formed the government with the support of allies.
Totaliser is a proposed mechanism in the voting machines in India to hide the booth-wise voting patterns. A totaliser allows the votes cast in about 14 polling booths to be counted together. At present, the votes are tallied booth by booth.
An election audit is any review conducted after polls close for the purpose of determining whether the votes were counted accurately or whether proper procedures were followed, or both.
The 2019 Andhra Pradesh Legislative Assembly election were held in the Indian state of Andhra Pradesh on 11 April 2019 for constituting the fifteenth legislative assembly in the state. They were held alongside the 2019 Indian general election.
Electronic voting in the United States involves several types of machines: touchscreens for voters to mark choices, scanners to read paper ballots, scanners to verify signatures on envelopes of absentee ballots, and web servers to display tallies to the public. Aside from voting, there are also computer systems to maintain voter registrations and display these electoral rolls to polling place staff.
Municipal election were held in Delhi on 4 December 2022 to elect 250 councillors of Municipal Corporation of Delhi. The votes were counted and the results were declared on 7 December 2022.