Metre sea water

Last updated
metre sea water
Manometro de la camara.jpg
Hyperbaric chamber pressure gauge calibrated in msw and bar
General information
Unit of pressure
Symbolmsw
Conversions
1 msw in ...... is equal to ...
    SI units    =10000.0  Pa
    CGS units    =100000  Ba
    U.S. customary    3.263 fsw
1.45038  psi
foot sea water
Pressure gauge on Siebe Gorman manual diver's pump P3220126.jpg
Pressure gauge on Siebe Gorman manual diver's pump calibrated in fsw and psi
General information
Unit of pressure
Symbolfsw
Conversions
1 fsw in ...... is equal to ...
    SI units    3064.3  Pa
    CGS units    30643  Ba
    U.S. customary    0.44444  psi

The metre (or meter) sea water (msw) is a metric unit of pressure used in underwater diving. It is defined as one tenth of a bar. [1] [2]

Contents

The unit used in the US is the foot sea water (fsw), based on standard gravity and a sea-water density of 64 lb/ft3. According to the US Navy Diving Manual, one fsw equals 0.30643 msw, 0.030643  bar , or 0.44444  psi , [1] [2] though elsewhere it states that 33 fsw is 14.7 psi (one atmosphere), which gives one fsw equal to about 0.445 psi. [3]

The msw and fsw are the conventional units for measurement of diver pressure exposure used in decompression tables and the unit of calibration for pneumofathometers and hyperbaric chamber pressure gauges. [4]

Feet of sea water

One atmosphere is approximately equal to 33 feet of sea water or 14.7 psi, which gives 4.9/11 or about 0.445 psi per foot. Atmospheric pressure may be considered constant at sea level, and minor fluctuations caused by the weather are usually ignored. [5] Pressures measured in fsw and msw are gauge pressure, relative to the surface pressure of 1 atm absolute, except when a pressure difference is measured between the locks of a hyperbaric chamber, which is also generally measured in fsw and msw.

The pressure of seawater at a depth of 33 feet equals one atmosphere. The absolute pressure at 33 feet depth in sea water is the sum of atmospheric and hydrostatic pressure for that depth, and is 66 fsw, or two atmospheres absolute. For every additional 33 feet of depth, another atmosphere of pressure accumulates. [6] Therefore at the surface the gauge pressure of 0 fsw is equivalent to an absolute pressure of 1 standard atmosphere (14.7 psi), and the gauge pressure in fsw at any depth is incremented by 1 ata to provide absolute pressure. (Pressure in ata = Depth in feet/33 + 1) [7]

Usage

Surface supply air panel for 4 divers with pneumofathometer gauges calibrated in metres and feet seawater Surface supply air panel for 4 divers P3053737.jpg
Surface supply air panel for 4 divers with pneumofathometer gauges calibrated in metres and feet seawater

In diving the absolute pressure is used in most computations, particularly for decompression and breathing gas consumption but depth is measured by way of hydrostatic pressure. [8] In metric units the ambient pressure is usually measured in metres sea water (msw), and converted to bar for calculations. In US customary units ambient pressure is normally measured in feet of sea water (fsw), and converted to atmospheres absolute or pounds per square inch absolute (psia) for decompression computation. Feet and metres sea water are convenient measures which approximate closely to depth and are intuitively simple to grasp for the diver, compared to the options of more conventional units of pressure which give no direct indication of depth. The distinction between gauge and absolute pressure is important for calculation of gas properties and pressure must be identified as either gauge or absolute. Gauge pressure in msw or fsw is converted to absolute pressure in bar or atm for decompression and gas consumption calculation, but decompression tables are usually provided ready for use directly with the gauge pressure in msw and fsw. Depth gauges and dive computers with readouts calibrated in feet and metres are actually displaying a pressure measurement, usually in feet or metres sea water, as most diving is done in the sea. If ambient pressure in fresh water and hyperbaric chambers is measured in feet and metres sea water, the same decompression algorithms and tables can be used, which eliminates the need to use calibration factors when diving in these environments. [8]

Conversions

In the metric system, a pressure of 10 msw is defined as 1 bar. Pressure conversion between msw and fsw is slightly different from length conversion between metres and feet; 10 msw = 32.6336 fsw and 10 m = 32.8083 ft. [1]

The US Navy Diving Manual gives conversion factors for "fw" (feet water) based on a fresh water density of 62.4 lb/ft3 and for fsw based on a sea water density of 64.0 lb/ft3. [1]

One standard metre sea water equals: [1]

One standard metre sea water is also approximately equal to: [1]

One standard foot sea water is approximately equal to: [1]

Similar units

Related Research Articles

<span class="mw-page-title-main">Pressure measurement</span>

Pressure measurement is the measurement of an applied force by a fluid on a surface. Pressure is typically measured in units of force per unit of surface area. Many techniques have been developed for the measurement of pressure and vacuum. Instruments used to measure and display pressure mechanically are called pressure gauges,vacuum gauges or compound gauges. The widely used Bourdon gauge is a mechanical device, which both measures and indicates and is probably the best known type of gauge.

<span class="mw-page-title-main">Pressure</span> Force distributed over an area

Pressure is the force applied perpendicular to the surface of an object per unit area over which that force is distributed. Gauge pressure is the pressure relative to the ambient pressure.

Atmospheric pressure, also known as air pressure or barometric pressure, is the pressure within the atmosphere of Earth. The standard atmosphere is a unit of pressure defined as 101,325 Pa (1,013.25 hPa), which is equivalent to 1,013.25 millibars, 760 mm Hg, 29.9212 inches Hg, or 14.696 psi. The atm unit is roughly equivalent to the mean sea-level atmospheric pressure on Earth; that is, the Earth's atmospheric pressure at sea level is approximately 1 atm.

<span class="mw-page-title-main">Deep diving</span> Underwater diving to a depth beyond the norm accepted by the associated community

Deep diving is underwater diving to a depth beyond the norm accepted by the associated community. In some cases this is a prescribed limit established by an authority, while in others it is associated with a level of certification or training, and it may vary depending on whether the diving is recreational, technical or commercial. Nitrogen narcosis becomes a hazard below 30 metres (98 ft) and hypoxic breathing gas is required below 60 metres (200 ft) to lessen the risk of oxygen toxicity. At much greater depths, breathing gases become supercritical fluids, making diving with conventional equipment effectively impossible regardless of the physiological effects on the human body. Air, for example, becomes a supercritical fluid below about 400 metres (1,300 ft).

<span class="mw-page-title-main">Dive computer</span> Instrument to calculate decompression status in real time

A dive computer, personal decompression computer or decompression meter is a device used by an underwater diver to measure the elapsed time and depth during a dive and use this data to calculate and display an ascent profile which, according to the programmed decompression algorithm, will give a low risk of decompression sickness. A secondary function is to record the dive profile, warn the diver when certain events occur, and provide useful information about the environment.

<span class="mw-page-title-main">Saturation diving</span> Diving decompression technique

Saturation diving is diving for periods long enough to bring all tissues into equilibrium with the partial pressures of the inert components of the breathing gas used. It is a diving mode that reduces the number of decompressions divers working at great depths must undergo by only decompressing divers once at the end of the diving operation, which may last days to weeks, having them remain under pressure for the whole period. A diver breathing pressurized gas accumulates dissolved inert gas used in the breathing mixture to dilute the oxygen to a non-toxic level in the tissues, which can cause potentially fatal decompression sickness if permitted to come out of solution within the body tissues; hence, returning to the surface safely requires lengthy decompression so that the inert gases can be eliminated via the lungs. Once the dissolved gases in a diver's tissues reach the saturation point, however, decompression time does not increase with further exposure, as no more inert gas is accumulated.

In-water recompression (IWR) or underwater oxygen treatment is the emergency treatment of decompression sickness (DCS) by returning the diver underwater to help the gas bubbles in the tissues, which are causing the symptoms, to resolve. It is a procedure that exposes the diver to significant risk which should be compared with the risk associated with the available options and balanced against the probable benefits. Some authorities recommend that it is only to be used when the time to travel to the nearest recompression chamber is too long to save the victim's life; others take a more pragmatic approach and accept that in some circumstances IWR is the best available option. The risks may not be justified for case of mild symptoms likely to resolve spontaneously, or for cases where the diver is likely to be unsafe in the water, but in-water recompression may be justified in cases where severe outcomes are likely if not recompressed, if conducted by a competent and suitably equipped team.

In underwater diving activities such as saturation diving, technical diving and nitrox diving, the maximum operating depth (MOD) of a breathing gas is the depth below which the partial pressure of oxygen (pO2) of the gas mix exceeds an acceptable limit. This limit is based on risk of central nervous system oxygen toxicity, and is somewhat arbitrary, and varies depending on the diver training agency or Code of Practice, the level of underwater exertion expected and the planned duration of the dive, but is normally in the range of 1.2 to 1.6 bar.

<span class="mw-page-title-main">Diving chamber</span> Hyperbaric pressure vessel for human occupation used in diving operations

A diving chamber is a vessel for human occupation, which may have an entrance that can be sealed to hold an internal pressure significantly higher than ambient pressure, a pressurised gas system to control the internal pressure, and a supply of breathing gas for the occupants.

<span class="mw-page-title-main">United States Navy Experimental Diving Unit</span> The primary source of diving and hyperbaric operational guidance for the US Navy

The United States Navy Experimental Diving Unit is the primary source of diving and hyperbaric operational guidance for the US Navy. It is located within the Naval Support Activity Panama City in Panama City Beach, Bay County, Florida.

<span class="mw-page-title-main">Ascending and descending (diving)</span> Procedures for safe ascent and descent in underwater diving

In underwater diving, ascending and descending is done using strict protocols to avoid problems caused by the changes in ambient pressure and the hazards of obstacles near the surface such as collision with vessels. Diver certification and accreditation organisations place importance on these protocols early in their diver training programmes. Ascent and descent are historically the times when divers are injured most often when failing to follow appropriate procedure.

<span class="mw-page-title-main">George F. Bond</span> US Navy physician and diving medicine and saturation diving researcher

Captain George Foote Bond was a United States Navy physician who was known as a leader in the field of undersea and hyperbaric medicine and the "Father of Saturation Diving".

<span class="mw-page-title-main">Decompression practice</span> Techniques and procedures for safe decompression of divers

To prevent or minimize decompression sickness, divers must properly plan and monitor decompression. Divers follow a decompression model to safely allow the release of excess inert gases dissolved in their body tissues, which accumulated as a result of breathing at ambient pressures greater than surface atmospheric pressure. Decompression models take into account variables such as depth and time of dive, breathing gasses, altitude, and equipment to develop appropriate procedures for safe ascent.

<span class="mw-page-title-main">History of decompression research and development</span> Chronological list of notable events in the history of diving decompression.

Decompression in the context of diving derives from the reduction in ambient pressure experienced by the diver during the ascent at the end of a dive or hyperbaric exposure and refers to both the reduction in pressure and the process of allowing dissolved inert gases to be eliminated from the tissues during this reduction in pressure.

Compression arthralgia is pain in the joints caused by exposure to high ambient pressure at a relatively high rate of compression, experienced by underwater divers. Also referred to in the U.S. Navy Diving Manual as compression pains.

<span class="mw-page-title-main">Haldane's decompression model</span> Decompression model developed by John Scott Haldane

Haldane's decompression model is a mathematical model for decompression to sea level atmospheric pressure of divers breathing compressed air at ambient pressure that was proposed in 1908 by the Scottish physiologist, John Scott Haldane, who was also famous for intrepid self-experimentation.

<span class="mw-page-title-main">Hyperbaric treatment schedules</span> Planned hyperbaric exposure using a specified breathing gas as medical treatment

Hyperbaric treatment schedules or hyperbaric treatment tables, are planned sequences of events in chronological order for hyperbaric pressure exposures specifying the pressure profile over time and the breathing gas to be used during specified periods, for medical treatment. Hyperbaric therapy is based on exposure to pressures greater than normal atmospheric pressure, and in many cases the use of breathing gases with oxygen content greater than that of air.

<span class="mw-page-title-main">Decompression equipment</span> Equipment used by divers to facilitate decompression

There are several categories of decompression equipment used to help divers decompress, which is the process required to allow divers to return to the surface safely after spending time underwater at higher ambient pressures.

<span class="mw-page-title-main">Built-in breathing system</span> System for supply of breathing gas on demand within a confined space

A built-in breathing system is a source of breathing gas installed in a confined space where an alternative to the ambient gas may be required for medical treatment, emergency use, or to minimise a hazard. They are found in diving chambers, hyperbaric treatment chambers, and submarines.

The US Navy has used several decompression models from which their published decompression tables and authorized diving computer algorithms have been derived. The original C&R tables used a classic multiple independent parallel compartment model based on the work of J.S.Haldane in England in the early 20th century, using a critical ratio exponential ingassing and outgassing model. Later they were modified by O.D. Yarborough and published in 1937. A version developed by Des Granges was published in 1956. Further developments by M.W. Goodman and Robert D. Workman using a critical supersaturation approach to incorporate M-values, and expressed as an algorithm suitable for programming were published in 1965, and later again a significantly different model, the VVAL 18 exponential/linear model was developed by Edward D. Thalmann, using an exponential ingassing model and a combined exponential and linear outgassing model, which was further developed by Gerth and Doolette and published in Revision 6 of the US Navy Diving Manual as the 2008 tables.

References

  1. 1 2 3 4 5 6 7 8 US Navy Diving Manual 2016, Table 2‑10. Pressure Equivalents..
  2. 1 2 Staff (2016). "2 - Diving physics". Guidance for Diving Supervisors (IMCA D 022 August 2016, Rev. 1 ed.). London, UK: International Marine Contractors' Association. p. 3.
  3. Page 2-12.
  4. US Navy Diving Manual 2016, Section 18‑2.8.3.
  5. US Navy Diving Manual 2016, Section 2-9.1.
  6. US Navy Diving Manual 2016, Section 2-9.3.
  7. US Navy Diving Manual 2016, Table 2‑1. Pressure Chart, and Figure 2.7.
  8. 1 2 NOAA Diving Program (U.S.) (December 1979). Miller, James W. (ed.). NOAA Diving Manual, Diving for Science and Technology (2nd ed.). Silver Spring, Maryland: US Department of Commerce: National Oceanic and Atmospheric Administration, Office of Ocean Engineering.

Sources