Cave-diving is underwater diving in water-filled caves. It may be done as an extreme sport, a way of exploring flooded caves for scientific investigation, or for the search for and recovery of divers or, as in the 2018 Thai cave rescue, other cave users. The equipment used varies depending on the circumstances, and ranges from breath hold to surface supplied, but almost all cave-diving is done using scuba equipment, often in specialised configurations with redundancies such as sidemount or backmounted twinset. Recreational cave-diving is generally considered to be a type of technical diving due to the lack of a free surface during large parts of the dive, and often involves planned decompression stops. A distinction is made by recreational diver training agencies between cave-diving and cavern-diving, where cavern diving is deemed to be diving in those parts of a cave where the exit to open water can be seen by natural light. An arbitrary distance limit to the open water surface may also be specified. [1]
Equipment, procedures, and the requisite skills have been developed to reduce the risk of becoming lost in a flooded cave, and consequently drowning when the breathing gas supply runs out. The equipment aspect largely involves the provision of an adequate breathing gas supply to cover reasonably foreseeable contingencies, redundant dive lights and other safety critical equipment, and the use of a continuous guideline leading the divers back out of the overhead environment. The skills and procedures include effective management of the equipment, and procedures to recover from foreseeable contingencies and emergencies, both by individual divers, and by the teams that dive together.
In the United Kingdom, cave-diving developed from the locally more common activity of caving. Its origins in the United States are more closely associated with recreational scuba diving. Compared to caving and scuba diving, there are relatively few practitioners of cave-diving. This is due in part to the specialized equipment and skill sets required, and in part because of the high potential risks due to the specific environment.
Despite these risks, water-filled caves attract scuba divers, cavers, and speleologists due to their often unexplored nature, and present divers with a technical diving challenge. Underwater caves have a wide range of physical features, and can contain fauna not found elsewhere. Several organisations dedicated to cave diving safety and exploration exist, and several agencies provide specialised training in the skills and procedures considered necessary for acceptable safety.
Two types of overhead diving environment are defined in recreational cave diving:
The underwater cave environment includes those parts of caves which may be explored underwater. Recreational cave diving can be defined as diving underground beyond the reach of natural daylight, as a way of distinguishing between cave and cavern diving. In this context, while artificially formed underground spaces such as mines are not generally called caves by divers, the activity of diving in them is classed as cave diving for training and certification purposes by diver training agencies
This section needs expansionwith: define. You can help by adding to it. (July 2024) |
Cavern diving is an arbitrarily defined, limited scope activity of diving in the naturally illuminated part of underwater caves, where the risk of getting lost is small, as the exit can be seen, and the equipment needed is reduced due to the limited distance to surface air. It is defined as a recreational diving activity as opposed to a technical diving activity on the grounds of low risk and basic equipment requirements. [1] [2]
The procedures of cave-diving have much in common with procedures used for other types of penetration diving. They differ from open-water diving procedures mainly in the emphasis on navigation, gas management, operating in confined spaces, and that the diver is physically constrained from direct ascent to the surface during much of the dive.[ citation needed ]
As most cave-diving is done in an environment where there is no free surface with breathable air allowing an above-water exit, it is critically important to be able to find the way out before the breathing gas runs out. This is ensured by the use of a continuous guideline between the dive team and a point outside of the flooded part of the cave, and diligent planning and monitoring of gas supplies. Two basic types of guideline are used: permanent lines, and temporary lines. Permanent lines may include a main line starting near the entrance/exit, and side lines or branch lines, and are marked to indicate the direction along the line to the nearest exit. Temporary lines include exploration lines and jump lines. [3]
Decompression procedures may take into account that the cave diver usually follows a very rigidly constrained and precisely defined route, both into and out of the cave, and can reasonably expect to find any equipment such as drop cylinders temporarily stored along the guideline while making the exit. In some caves, changes of depth of the cave along the dive route will constrain decompression depths, and gas mixtures and decompression schedules can be tailored to take this into account.[ citation needed ]
Most open-water diving skills apply to cave-diving, and there are additional skills specific to the environment, and to the chosen equipment configuration.
The essential cave-diving procedure is navigation using a guide line. This includes laying and marking line, following line and interpreting line markers, avoiding entanglement, recovering from entanglement, maintaining and repairing line, finding lost line, jumping gaps, and recovering line, any of which may need to be done in zero visibility, total darkness, tight confined spaces or a combination of these conditions.
Losing the guide line in a cave is a potentially life-threatening emergency. While following recommended best practice makes it highly unlikely that a diver will lose the line, it can and does happen, and there are procedures which will usually work to find it again. Any reliable information on where the diver is likely to be relative to the last known position of the line may be critical, and the procedure of choice will depend on what is reliably known. In all situations, the diver will attempt to stabilise the situation and avoid getting further lost, and make a thorough visual check in all directions from where they are at the time, taking into account the possibility of the line being in a line trap. If the diver has not also separated from their buddy, the buddy may know where the line is, and can be asked, and if the diver is separated from their buddy, the buddy may be at the line, and the buddy's light may be visible. [11]
Stabilising the position is generally done by finding the nearest feasible tie-off point and securely tying off a search line. The direction of the guide line when last seen should be known, and therefore the direction the diver was swimming in before losing the line. If the diver was neutrally buoyant while following the line, the approximate depth can be reconstructed by finding the depth of neutral buoyancy again, without adjusting inflation of BCD or dry suit. Unless the line was lost by the diver not noticing a change of direction, it is likely to be at much the same depth, in much the same direction, and at a similar lateral and vertical distance as when last seen, making it logical to try that direction first. While swimming towards the estimated position of the line and slowly paying out search line, the diver will search visually, and in low visibility or darkness, also by feel, making arm sweeps across the expected direction of the line, while defending the head from impact with the other arm. The distance swum towards the estimated position of the lost line can be measured by the spacing and number of knots paid out on the search line. If the search fails, the diver will return to the tie off and try again in the next best guess for the direction the line may be. [11] The diver may also choose to try a different search method. The best search method for any given situation will depend on the water conditions, the layout of the section of cave, the way the line was laid, the situational knowledge and skills of the diver, and the equipment available – a method that would be ideal for one situation might not work at all for another.
If the line is found, but not the other divers, the diver can tie off their search reel to the guide line as an indicator to other members of the team that they were lost but have found the guide line, and indicate the direction that they intend to proceed along the guideline with a personal directional marker so that others who see it while searching for the lost diver will know whether the diver chose the right direction to exit the cave. [11]
This is generally the converse situation to the lost guide line, in that the diver loses contact with their buddy or team but remains in contact with the guide line, so is not themselves lost. Their first priority is to not get lost or disorientated, and in furtherance of this aim would attach a directional line marker to the guide line indicating the direction to the exit before starting a search. The search line can be tied to the directional marker to prevent it from sliding along the line during the search. The direction for the search would depend on the layout of that part of the cave, and where the missing diver should have been in the group. The search party must consider their own safety first, regarding how much gas they can afford to use in a search, which will depend on the stage of the dive when the diver is noticed to be missing. When searching in darkness, the searchers should periodically turn off their lights as this will allow them to see the lost diver's light more easily. [11]
Gas planning is the aspect of dive planning which deals with the calculation or estimation of the amounts and mixtures of gases to be used for a planned dive profile. It usually assumes that the dive profile, including decompression, is known, but the process may be iterative, involving changes to the dive profile as a consequence of the gas requirement calculation, or changes to the gas mixtures chosen. Use of calculated reserves based on planned dive profile and estimated gas consumption rates rather than an arbitrary pressure based on a fraction of the initial gas supply is sometimes referred to as rock bottom gas management. The purpose of gas planning is to ensure that for all reasonably foreseeable contingencies, the divers of a team have sufficient breathing gas to safely return to a place where more breathing gas is available. In almost all cases this will be the surface. [12]
Gas planning includes the following aspects: [13] : Sect.3
The primary breathing apparatus may be open circuit scuba or rebreather, and bailout may also be open circuit or rebreather. Emergency gas may be shared among the team members, or each diver may carry their own, but in all cases each diver must be able to bail out onto a gas supply of their own for long enough to get to the next planned source of emergency gas. If for any reason this situation no longer applies, there is a single point of critical failure, and the risk becomes unacceptable, so the dive should be turned.
Gas management also includes the blending, filling, analysing, marking, storage, and transportation of gas cylinders for a dive, and the monitoring and switching of breathing gases during a dive, and the provision of emergency gas to another member of the dive team. The primary aim is to ensure that everyone has enough to breathe of a gas suitable for the current depth at all times, and is aware of the gas mixture in use and its effect on decompression obligations and oxygen toxicity risk.
The rule of thirds for gas management is a rule of thumb used by divers to plan dives so they have enough breathing gas remaining in their diving cylinder at the end of the dive to be able to complete the dive safely. [5] [14] This rule mostly applies to diving in overhead environments, such as caves and wrecks, where a direct ascent to the surface is impossible and the divers must return the way they came.
For divers following the rule, one third of the gas supply is planned for the outward journey, one third is for the return journey and one third is a safety reserve. [5] However, when diving with a buddy with a higher breathing rate or a different volume of gas, it may be necessary to set one third of the buddy's gas supply as the remaining 'third'. This means that the turn point to exit is earlier, or that the diver with the lower breathing rate carries a larger volume of gas than he alone requires.
A different option for penetration dives is the Half + 15 bar (half + 200 psi) method, in which the contingency gas for the stage is carried in the primary cylinders. Some divers consider this method to be the most conservative when multi-staging. If all goes to plan when using this method, the divers surface with stages nearly empty, but with all the contingency gas still in their primary cylinders. With a single stage drop, this means the primary cylinders will still be about half-full. [15]
Cave-diving training includes equipment selection and configuration, guideline protocols and techniques, gas management protocols, communication techniques, propulsion techniques, emergency management protocols, and psychological education.[ clarification needed ][ citation needed ] Cave diver training also stresses the importance of risk management and cave conservation ethics.[ citation needed ] Most training systems offer progressive stages of education and certification. [16]
Various diver training and certification organizations offer training for cave divers, often based on the three cave zones defined by CMAS. Some organizations offer cavern diving training for recreational divers, (Zone 1). Cave diving involves significant risks, so a self-taught approach is discouraged.
The following training courses are offered by the listed organisations:
Zone | CMAS [18] | GUE [19] | ANDI [20] | NACD [21] | NAUI [22] | NSS-CDS [23] | PADI [24] | TDI |
---|---|---|---|---|---|---|---|---|
Cavern diver (Zone 1) | Cave diver I | Cavern Diver, Level 2 | Cavern Diver | Cavern Diver | Cavern Diver | Cavern Diver [25] | Cavern Diver [26] | |
Cave diver (Zone 2) | Cave diver II | Cave Diver Level 1 | Cave Diver, Level 1 | Intro to Cave Diving | Cave Diver Level I | Basic/Intro Cave Diver | Intro to Cave | |
Cave Diver Level 2 | Apprentice to Cave | Apprentice Cave Diver | ||||||
Cave diver (Zone 3) | Cave diver III | Cave Diver Level 2 | Cave Diver, Level 3 and Cave Explorer, Level 4 | Full Cave Diver | Cave Diver Level II | Cave Diver | Full Cave | |
Cave diver (58 m) | Cave 2 + TEK 1 | Cave Explorer Level 5 | ||||||
Cave diver guide | Cave Guide (Technical Support Leader) | |||||||
Cave diving instructor 1 | Cave diving instructor I | Cave Instructor Level 1 | Assistant Instructor (ASI) | Cavern Instructor | Assistant Instructor | Instructor | Specialty Instructor [27] | |
Cave diving instructor 2 | Cave diving Instructor II | Cave Instructor Level 2 | Open Water Instructor (OWI) | Cave Instructor | Instructor | Instructor | ||
Cave diving instructor 3 | Cave diving instructor III | Cave Instructor Level 3 |
In France, courses organized by the national cave diving commission of the FFESSM, [28] are offered to holders of level 2 certification or higher. The French Cave Diving School of the FFS also offers courses open to any autonomous diver. [29]
A significant aspect of cave diving by competent and enthusiastic cave divers is exploration, survey and mapping. Data collected is often shared and may be stored on databases to help optimise the effectiveness of such surveys, and make the information generally available. [30]
Underwater cave mapping is complicated by both a lack of access to the surface for GPS positions, darkness, with short line-of-sight, and limited visibility, which complicate optical measurement. Altitude/depth is relatively simple as accurate depth measurement is available to divers in the form of decompression computers, which log a depth/time record of reasonable accuracy and are available for instantaneous readout at any point, and depth can be referenced to the altitude at the surface. Vertical dimensions can be directly measured or calculated as differences in depth. [30]
Surface coordinates can be collected via GPS and remote sensing, with varying degrees of precision and accuracy depending on the type of entrance. In some caves the water surface is in view of GPS satellites, in others it is a considerable distance along a complex route from the nearest open air. Three dimensional models of varying accuracy and detail can be created by processing measurements collected by whatever methods were available. These can be used in virtual reality models. The usual methods for survey and mapping of underwater caves are dead reckoning and direct measurements of distance, compass direction and depth, by diving teams of two or three scuba divers, who record azimuth of the cave line, measurements of height, width, depth, and slope at intervals along the line, generally using a permanent guide line as a reference baseline, and take photographic records of features and objects of interest. Data are collected on wet-notes and by digital photography. [30] Hand-held sonar may be used for distance measurement where available. Where the depth or other constraints prevent divers from exploring in person, tethered and untethered remotely operated underwater vehicles (ROUVs) have been used effectively, using sonar technology to scan and map the surroundings, and video to record the appearance.
Features, artifacts, remains, and other objects of interest are recorded in situ as effectively as possible, generally by photography. [30]
Cave-diving is one of the most challenging and potentially dangerous kinds of diving and presents many hazards. Cave-diving is a form of penetration diving, meaning that in an emergency a diver cannot swim vertically to the surface due to the cave's ceilings, and so must swim the entire way back out. The underwater navigation through the cave system may be difficult and exit routes may be at a considerable distance, requiring the diver to have sufficient breathing gas to make the journey. The dive may also be deep, resulting in potential deep diving risks.[ citation needed ]
Visibility can vary from nearly unlimited to low, or non-existent, and can go from very good to very bad in a single dive. While a less-intensive kind of diving called cavern diving does not take divers beyond the reach of natural light (and typically no deeper than 30 metres (100 feet)), and penetration not further than 60 m (200 ft), true cave-diving can involve penetrations of many thousands of feet, well beyond the reach of sunlight. The level of darkness experienced creates an environment impossible to see in without an artificial source of light even if the water is clear. Caves often contain sand, mud, clay, silt, or other sediment that can further reduce underwater visibility in seconds when stirred up. Consequently, visibility is often worse during exit, and divers rely on the guideline for finding the way out.[ citation needed ]
The water in caves can have strong flow. Most caves flooded to the surface at the cave mouth are either springs or siphons. Springs have out-flowing currents, where water is coming up out of the Earth and flowing out across the land's surface. Siphons have in-flowing currents where, for example, an above-ground river is going underground. Some caves are complex and have some tunnels with out-flowing currents, and other tunnels with in-flowing currents. Inflowing currents can cause serious problems for the diver, as they make the exit more difficult, and the diver is carried to spaces that are unfamiliar and may be dangerous, while outflowing currents generally make the exit quicker and the diver is carried through places they have been before and can be prepared for difficult areas.
Cave-diving has been perceived as one of the more deadly sports in the world. [5] This perception may be exaggerated because the majority of divers who have died in caves have either not undergone specialized training or have had inadequate equipment for the environment. [5] Some cave divers have suggested that cave-diving is statistically much safer than recreational diving due to the much larger barriers imposed by experience, training, and equipment cost, [5] but there is no definitive statistical evidence for this claim.
There is no reliable worldwide database listing all cave-diving fatalities. Such fractional statistics as are available, however, suggest that few divers have died while following accepted protocols and while using equipment configurations recognized as acceptable by the cave-diving community. [5] In the very rare cases of exceptions to this rule there have typically been unusual circumstances. [5]
Most cave divers recognize five general rules or contributing factors for safe cave-diving, which were popularized, adapted and became generally accepted from Sheck Exley's 1979 publication Basic Cave Diving: A Blueprint for Survival. [5] In this book, Exley included accounts of actual cave-diving accidents, and followed each one with a breakdown of what factors contributed to the accident. Despite the unique circumstances of each individual accident, Exley found that at least one of a small number of major factors contributed to each one. This technique for breaking down accident reports and finding common causes among them is now called accident analysis , and is taught in introductory cave-diving courses. Exley outlined a number of these resulting cave-diving rules, but today these five are the most recognized:
Most cave-diving fatalities are due to running out of gas before reaching the exit. This is often the direct consequence of getting lost, whether the guide line is found again or not, and whether the visibility deteriorates, lights fail, or someone panics. On rare occasions equipment failure is unrecoverable, or a diver becomes inextricably trapped, seriously injured, incapacitated by using an unsuitable gas for the depth, or swept away by strong flow. Getting lost means separation from the continuous guide line to the exit, and not knowing the direction to the exit.
Some cave divers are taught to remember the five key components with the mnemonic: "The Good Divers Always Live" (training, guide, depth, air, light). [33]
In recent years new contributing factors were considered after reviewing accidents involving solo diving, diving with incapable dive partners, video or photography in caves, complex cave dives and cave-diving in large groups. With the establishment of technical diving, the use of mixed gases—such as trimix for bottom gas, and nitrox and oxygen for decompression—reduces the margin for error. Accident analysis suggests that breathing the wrong gas for the depth or not analyzing the breathing gas properly has also led to cave-diving accidents.[ citation needed ]
Cave-diving requires a variety of specialized procedures, and divers who do not correctly apply these procedures may significantly increase the risk to the members of their team. The cave-diving community works hard to educate the public on the risks they assume when they enter water-filled caves. Warning signs with the likenesses of the Grim Reaper have been placed just inside the openings of many popular caves in the US and Mexico, and others have been placed in nearby parking lots and local dive shops. [34]
Many cave-diving sites around the world include open-water basins, which are popular open-water diving sites. The management of these sites try to minimize the risk of untrained divers being tempted to venture inside the cave systems. With the support of the cave-diving community, many of these sites enforce a "no-lights rule" for divers who lack cave training—they may not carry any lights into the water with them. [35] It is easy to venture into an underwater cave with a light and not realize how far away from the entrance (and daylight) one has swum; this rule is based on the theory that, without a light, divers will not venture beyond daylight.[ citation needed ]
In the early phases of cave-diving the analysis shows that 90% of accidents were not trained cave divers; from the 2000s on the trend has reversed to 80% of accidents involving trained cave divers.[ citation needed ] Modern cave divers' capability and available technology allows divers to venture well beyond traditional training limits[ clarification needed ] and into actual exploration. The result is an increase of cave-diving accidents, in 2011 the yearly average of 2.5 fatalities a year tripled.[ citation needed ] In 2012 fatalities reached the highest annual rate to that date at over 20.[ citation needed ]
As response to the increase in fatalities during the years 2010 onwards, the International Diving Research and Exploration Organization (IDREO) was created in order to "bring awareness of the current safety situation of Cave Diving" by listing current worldwide accidents by year and promoting a community discussion and analysis of accidents through a "Cave Diver Safety Meeting" held annually. [36]
Equipment used by cave divers ranges from fairly standard recreational scuba configurations, to more complex arrangements which allow more freedom of movement in confined spaces, extended range in terms of depth and time, allowing greater distances to be covered in acceptable safety, and equipment which helps with navigation, in what are usually dark, and often silty and convoluted spaces.[ citation needed ]
Scuba configurations which are more often found in cave-diving than in open water diving include independent or manifolded twin cylinder rigs, side-mount harnesses, sling cylinders, rebreathers and backplate and wing harnesses. Bill Stone designed and used epoxy composite tanks for exploration of the San Agustín and Sistema Huautla caves in Mexico to decrease the weight for dry sections and vertical passages. [37] [38]
Stage cylinders are cylinders which are used to provide gas for a portion of the penetration. They may be deposited on the bottom at the guideline on preparation dives, to be picked up for use during the main dive, or may be carried by the divers and dropped off at the line during the penetration to be retrieved on the way out.[ citation needed ]
One of the high risk hazards of cave-diving is getting lost in the cave. The use of guide lines is the standard mitigation for this risk. [5] Guide lines may be permanent or laid and recovered during the dive, using cave reels to deploy and recover the line. Permanent branch lines may be laid with a gap between the start of the branch line and the nearest point on the main line. Line used for this purpose is known as cave line. Gap spools with a relatively short line are commonly used to make the jump.[ citation needed ]
Line arrows are used to point towards the nearest exit, and cookies are used to indicate use of a line by a team of divers.[ citation needed ]
Silt screws are short lengths of rigid tube (usually plastic) with one sharpened end and a notch or slot at the other end to secure the line, which are pushed into the silt or detritus of the cave floor as a place to tie off a guideline when no suitable natural tie-off points are available.[ citation needed ]
A simple plastic helmet, such as those used in water sports like whitewater kayaking, is good protection in case of accidental contact with the cave ceiling or stalactites.[ citation needed ]
Diver propulsion vehicles, or Scooters, are sometimes used to extend the range by reducing the work load on the diver and allowing faster travel in open sections of cave. Reliability of the diver propulsion vehicle is very important, as a failure could compromise the ability of the diver to exit the cave before running out of gas. Where this is a significant risk, divers may tow a spare scooter.[ citation needed ]
Dive lights are critical safety equipment, as it is dark inside caves. Each diver generally carries a primary light, and at least one backup light. A minimum of three lights is recommended. [5] The primary light should last the planned duration of the dive, as should each of the backup lights. [5]
One of the earliest known cave dives was a freedive in 1922 by Norbert Casteret in the Montespan cave, France. [39]
Jacques-Yves Cousteau, co-inventor of the first commercially successful open circuit scuba equipment, was the world's first open circuit scuba cave diver.[ citation needed ] However, many cave divers penetrated caves prior to the advent of scuba with surface supplied breathing apparatus through the use of air hoses and compressors. Scuba diving in all its forms, including cave-diving, has advanced in earnest since Cousteau introduced the Aqua-Lung in 1943.[ citation needed ]
Two regions have had particular influence on cave-diving techniques and equipment due to their very different cave-diving environments. These are the United Kingdom, and the United States, mainly Florida.[ citation needed ]
On January 6, 2024, Xavier Méniscus broke the cave diving record by reaching a depth of 312 metres in the Font Estramar chasm, in Salses-le-Château, France. [40] The previous record of 308 m was held by Frédéric Swierczynski, [41] and before that by Xavier Méniscus at 286m, on 30 December 2019, both also at Font Estramar cave. [42] Before that, Nuno Gomez had descended to 282 metres at Boesmansgat in South Africa. [43]
The Cave Diving Group (CDG) was established informally in the United Kingdom in 1935 to organise training and equipment for the exploration of flooded caves in the Mendip Hills of Somerset. The first dive was made by Jack Sheppard on 4 October 1936, [44] using a home-made drysuit surface fed from a modified bicycle pump, which allowed Sheppard to pass Sump 1 of Swildon's Hole. Swildon's is an upstream feeder to the Wookey Hole resurgence system. The difficulty of access to the sump in Swildon's prompted operations to move to the resurgence, and the larger cave there allowed use of standard diving dress which was secured from the Siebe Gorman company. In UK cave-diving, the term "Sherpa" was used without irony for the people who carry the diver's gear although this has gone out of fashion; support is now more normally used, and before the development of SCUBA equipment such undertakings could be monumental operations.[ citation needed ]
Diving in the spacious third chamber of Wookey Hole led to a rapid series of advances, each of which was dignified by being given a successive number, until an air surface was reached at what is now known as "Chamber 9." Some of these dives were broadcast live on BBC radio.[ citation needed ]
The number of sites where standard diving dress could be used is clearly limited and there was little further progress before the outbreak of World War II reduced the caving community considerably. However, the rapid development of underwater warfare through the war made a lot of surplus equipment available. The CDG re-formed in 1946 and progress was rapid. Typical equipment at this time was a frogman rubber diving suit for insulation (water temperature in the UK is typically 4 °C), an oxygen diving cylinder, soda lime absorbent canister and counter-lung comprising a rebreather air system and an "AFLOLAUN", meaning "Apparatus For Laying Out Line And Underwater Navigation." The AFLOLAUN consisted of lights, line-reel, compass, notebook (for the survey), batteries, and more. [45]
Progress was typically by "bottom walking", as this was considered less dangerous than swimming (note the absence of buoyancy controls). The use of oxygen put a depth limit on the dive, which was considerably compensated by the extended dive duration. This was the normal diving equipment and methods until approximately 1960 when new techniques using wetsuits (which provide both insulation and buoyancy ), twin open-circuit SCUBA air systems the development of side mounting cylinders, helmet-mounted lights and free-swimming with fins. The increasing capacity and pressure rating of air bottles also extended dive durations. [46]
In the 1970s, cave-diving greatly increased in popularity among divers in the United States. However, there were very few experienced cave divers and almost no formal classes to handle the surge in interest. The result was a large number of divers trying to cave dive without any formal training. This resulted in more than 100 fatalities over the course of the decade. The state of Florida came close to banning SCUBA diving around the cave entrances. The cave-diving organizations responded to the problem by creating training programs and certifying instructors, in addition to other measures to try to prevent these fatalities. This included posting signs, adding no-lights rules, and other enforcements.[ citation needed ]
In the United States, Sheck Exley was a pioneering cave diver who first explored many underwater cave systems in Florida, and many throughout the US and the world. On 6 February 1974, Exley became the first chairman of the Cave Diving Section of the National Speleological Society. [47]
Since the 1980s, cave-diving education has greatly reduced diver fatalities, and it is now rare for an agency trained diver to perish in an underwater cave. Also in the 1980s, refinements were made to the equipment used for cave-diving, most importantly better lights with smaller batteries. In the 1990s, cave-diving equipment configurations became more standardized, due mostly to the adaptation and popularization of the "Hogarthian rig", developed by several North Florida cave divers, particularly William Hogarth Main, which promotes equipment choices that "keep it simple and streamlined".[ citation needed ]
Today,[ when? ] the cave community is most focused on training, exploration, public awareness, and cave conservation.[ citation needed ]
Documentary films made by Wesley C. Skiles and Jill Heinerth have contributed to the increasing popularity of cave-diving in the early 21st century.[ citation needed ]
Four divers using scuba dived from the Right Imperial Cave in the Jenolan system in the Blue Mountains to an upstream chamber on 30 October 1954. [48]
Before the development of underwater breathing equipment, speleologists explored submerged cavities on breathhold (apnea), and with the equipment of the period: swimming underwater in total darkness, and with candles and matches for subsequent exploration.
In 1909, Eugene Fournier explored the Rigole source in Perpignan, diving to a depth of four meters to explore the continuation of the cavity. [49]
In 1924, Norbert Casteret explored the Montespan grotto in Haute-Garonne, where he swam through two successive siphons equipped with candles and matches. [50]
Between 1936 and 1949, Max Cosyns explored various springs in Sainte Engrace, in Pais Vasco, Spain, passing through siphons on breathhold and then continuing the exploration. [51] [52]
After the development of scuba diving, the possibilities of cave diving have expanded. For example:
In 1953, the scouts of the La Verna Clan of Lyon (Letrone, Eppely and Ballandraux) explored the Lamina Zilua spring in Sainte Engrace (Sola), passing through three siphons and stopping at the very narrow entry to the fourth. [53]
The Fernández Rubio brothers developed a new apnea technique for cave diving, which was used in the explorations of the Mairuelegorreta cave in 1959. [54]
In 1965 and 1966, led by Max Cosyns, [55] cave divers from Namur managed to climb the Kakueta Waterfall Cave (Cueva de la Cascada de Kakueta) to a fifth siphon 500 meters from the entrance, which despite diving to a depth of 30 m, they were unable to cross. [56]
In 1973, the cave divers Barroumés and Larribau crossed the Erberua siphon (Labort), and discovered a gallery on the other side with an important archaeological site. [57]
In 1973, the cave diver R. Jean (Fontaine la Tronche Group) crossed the first siphon of the Gouffre des Bourrugues (Larra), at a depth of 305 m below the surface. [58]
In 1980-81 Fred Vergier passed the first 3 siphons of Sima de las Puertas de Illamina (BU-56), reaching a depth of -1338 m. [59] [60] In 1986 divers from the Grupo Studenets Pleven of Bulgaria passed through the fourth siphon, reaching a depth of -1355 meters. In 1987, members of the same club passed the 5th and 6th siphons, subsequently exploring a wide gallery 650 meters long, and reaching the level of -1408 m, at the time the second deepest known chasm.
Several organisations exist to support caving and cave diving. Some of them also specifically train and certify cave divers to their own standards. There are also organisations dedicated to exploration, survey, and mapping of cave systems, both dry and flooded.
The Cave Divers Association of Australia (CDAA) is a cave diving organisation which was formed in September 1973 to represent the interests of recreational scuba divers who dive in water-filled caves and sinkholes principally in the Lower South East (now called the Limestone Coast) of South Australia (SA) and secondly in other parts of Australia. Its formation occurred after a series of diving fatalities in water-filled caves and sinkholes in the Mount Gambier region between 1969 and 1973 and in parallel to a South Australian Government inquiry into these deaths. The CDAA's major achievement has been the dramatic reduction of fatalities via the introduction of a site rating scheme and an associated testing system which was brought in during the mid-1970s. While its major area of operation is in the Limestone Coast region of SA, it administrates and supports cave diving activity in other parts of Australia including the Nullarbor Plain and Wellington, New South Wales.
The Cave Diving Group (CDG) is a United Kingdom-based diver training organisation specialising in cave diving.
The CDG was founded in 1946 by Graham Balcombe, making it the world's oldest continuing diving club. Graham Balcombe and Jack Sheppard pioneered cave diving in the late 1930s, notably at Wookey Hole in Somerset.
The National Association for Cave Diving (NACD) is a 501(c)(3) non-profit corporation founded in 1968 with the goal of improving the safety of scuba diving in caves through diver training and education. [61] [31] Its headquarters are in Gainesville, Florida but administration and operations are conducted from High Springs, Florida. The NACD is overseen by a board of directors composed of seven cave divers, four instructors, and three other directors. The elected officers are a president, vice president, secretary/treasurer, and training director. [62] Membership is open to all who have an interest in underwater caves. [31] The NACD publishes a quarterly journal, [63] and various specialised publications, holds seminars, [61] and workshops, and sponsors cave diving projects. [64]
The goals of the NACD are:
NACD offers training and certification in cavern and cave diving, and instructor courses. [65] The goal is not to encourage cavern or cave diving, but to aid divers in becoming safe cavern and cave divers. The NACD provides training standards to define their technical and philosophical principles of cave and cavern diving, but allows the instructors discretion and freedom use their own knowledge, experience, and teaching style, and acknowledges that many aspects of cave and cavern diving practice, procedure, and equipment configuration remain open to interpretation by equally qualified experts and that it is in the best interest of the student to be presented with differing views. [31]
The NACD philosophy of safe cave diving is based on a system of checks and balances to insure that NACD standards are maintained in each course. The courses available are as described below: [31]
The cavern diving course develops minimum skills, knowledge, dive planning abilities, problem solving procedures and the basic abilities to safely cavern dive. These skills are useful in all types of diving. The course is taught in over a minimum of two days and includes classroom lectures, field exercises, open water line drills and a minimum of four cavern dives. This course emphasizes planning, procedures, environment, propulsion techniques, buoyancy skills, problem solving, equipment modification and the specialized needs of the cavern diver. [31] The prerequisite qualification is Advanced Open Water Diver or equivalent.
The Introduction to Cave Diving course further develops cave diving proficiency within the limitations of a single tank. It is taught over a minimum of two days and includes a minimum of four single tank cave dives. The course helps hone the skills learned on the cavern diving course, and teaches new skills and procedures for limited single tank cave penetration. [31] It is considered a recreational cave diving course, and does not include obligatory decompression. The prerequisite qualification is cavern diver or equivalent and 25 logged non-training dives.
The Apprentice Cave Diver course is a training level which expires after a year if the full cave certification is not completed. It is an introduction to jump and gap procedures. The prerequisites are NACD Introduction to Cave or equivalent. [31]
The full Cave Diver course covers is equipment configuration, decompression problem solving, jumps, circuits, traverses, and surveying. The prerequisite is NACD Introduction to Cave or equivalent. [31]
NACD offers specialty cave diver training for the fully certified cave diver. Courses offered are: [31]
Four instructor certification levels are available. [31]
The National Speleological Society (NSS) is an organization formed in 1941 to advance the exploration, conservation, study, and understanding of caves in the United States. Originally headquartered in Washington D.C., its current offices are in Huntsville, Alabama. The organization engages in the research and scientific study, restoration, exploration, and protection of caves. It has more than 10,000 members in more than 250 grottos. [66] Since 1974 there has been as cave diving section of the society. [67] [47]
The Quintana Roo Speleological Survey (QRSS) was established in 1990 for the safe exploration, survey and cartography of the underwater and dry caves and cenotes of Quintana Roo, Mexico, supported by the National Speleological Society. [68]
The survey principally acts as a data repository for explored sites within the state of Quintana Roo and distributes summary statistical tables through its webpage, which as of February, 2011 included 208 underwater cave systems with a total surveyed length of 910.4 kilometers (565.7 mi), and 50 caves above the water table with a total length of 41.8 kilometers (26.0 mi).
The Woodville Karst Plain Project (WKPP is a project and organization that maps the underwater cave systems underlying the Woodville Karst Plain, a 450-square-mile (1,200 km2) area from Tallahassee, Florida, U.S. to the Gulf of Mexico which includes several first magnitude springs, including Wakulla Springs, and the Leon Sinks cave system, the longest underwater cave in the United States. [69] [70] [71] The project grew out of a cave diving research and exploration group established in 1985 and incorporated in 1990 (by Bill Gavin and Bill Main, later joined by Parker Turner, Lamar English and Bill McFaden, at the time the chairman of the NACD Exploration and Survey Committee).
Cave-diving venues can be found on all continents except Antarctica, where the average temperature is too low for water to remain liquid in caves.
There are few flooded caves in Africa which are known and accessible. There are several in South Africa, a few in Namibia and Zimbabwe, and some large caves recently discovered in Madagascar.
There are a large number of flooded caves in the limestone regions and other regions of Asia, particularly in the karst regions of China and Southeast Asia. Some are accessible for recreational cave-diving, but most have probably not yet been found or explored.
Australia has many spectacular water filled caves and sinkholes, many of them in the Mount Gambier region of South Australia.
Europe has a large number of flooded caves, particularly in the karst regions.
North America has many cave-diving venues, particularly in Florida, USA, and the Yucatán Peninsula of Mexico.
South America has some cave-diving venues in Brazil.
The islands of The Bahamas have large number of underwater caves and blue holes found throughout the archipelago.
This section needs expansion. You can help by adding to it. (September 2022) |
Caves and caverns as geographical entities are defined differently from cave-diving and cavern-diving, so it is possible to be cavern diving in what is technically a cave, and cave-diving in what is technically a cavern.
A cave dive can be categorised by the topology of the route, which can be linear, include a circuit, or be a traverse. [75]
These terms describe flooded cave areas with reference to flow direction.
Cave where water flows out of the entrance used for diving. The flow will generally help divers on the way out.
A cave where water flows into the entrance used for diving, which can hinder divers from getting out.
A locally low-lying water filled passage of a cave. A cave may have several sumps separated by unflooded or partially flooded areas.
Cave caused by wind erosion.
Flooded mines and other underground spaces excavated by people and their machinery, by technical definition are not caves, but the activity of diving in such spaces is considered cave-diving, as the procedures and equipment are the same.
Caves caused by volcanic action, where a lava flow cools and solidifies on the outside, and the fluid interior lava flows out at the lower end when the supply stops. They may be branched, but are usually continuously sloped. Other caves formed through volcanic activity include rifts, lava molds, open vertical conduits, inflationary, and blister caves. [76]
Cave along the shore of a coastal area. [4] Usually created by wave action, and may be affected by tidal currents and wave surge.
Cave formed by groundwater dissolving the rock over long periods. They are more common in rocks which are more soluble in mildly acidic water, such as limestones and dolomites, and may be common in karst regions.
Cave formed by rock falls.
Notable cave divers:
Other:
An overhead or penetration diving environment is where the diver enters a space from which there is no direct, purely vertical ascent to the safety of breathable atmosphere at the surface. Cave diving, wreck diving, ice diving and diving inside or under other natural or artificial underwater structures or enclosures are examples. The restriction on direct ascent increases the risk of diving under an overhead, and this is usually addressed by adaptations of procedures and use of equipment such as redundant breathing gas sources and guide lines to indicate the route to the exit.
Technical diving is scuba diving that exceeds the agency-specified limits of recreational diving for non-professional purposes. Technical diving may expose the diver to hazards beyond those normally associated with recreational diving, and to a greater risk of serious injury or death. Risk may be reduced via appropriate skills, knowledge, and experience. Risk can also be managed by using suitable equipment and procedures. The skills may be developed through specialized training and experience. The equipment involves breathing gases other than air or standard nitrox mixtures, and multiple gas sources.
Deep diving is underwater diving to a depth beyond the norm accepted by the associated community. In some cases this is a prescribed limit established by an authority, while in others it is associated with a level of certification or training, and it may vary depending on whether the diving is recreational, technical or commercial. Nitrogen narcosis becomes a hazard below 30 metres (98 ft) and hypoxic breathing gas is required below 60 metres (200 ft) to lessen the risk of oxygen toxicity. At much greater depths, breathing gases become supercritical fluids, making diving with conventional equipment effectively impossible regardless of the physiological effects on the human body. Air, for example, becomes a supercritical fluid below about 400 metres (1,300 ft).
Sheck Exley was an American cave diver. He is widely regarded as one of the pioneers of cave diving, and he wrote two major books on the subject: Basic Cave Diving: A Blueprint for Survival and Caverns Measureless to Man. On February 6, 1974, Exley became the first chairman of the Cave Diving Section of the American National Speleological Society. During his career, he established many of the basic safety procedures used in cave and overhead diving today. Exley was also a pioneer of extreme deep scuba diving.
Scuba diving is a mode of underwater diving whereby divers use breathing equipment that is completely independent of a surface breathing gas supply, and therefore has a limited but variable endurance. The name scuba is an anacronym for "Self-Contained Underwater Breathing Apparatus" and was coined by Christian J. Lambertsen in a patent submitted in 1952. Scuba divers carry their own source of breathing gas, usually compressed air, affording them greater independence and movement than surface-supplied divers, and more time underwater than free divers. Although the use of compressed air is common, a gas blend with a higher oxygen content, known as enriched air or nitrox, has become popular due to the reduced nitrogen intake during long or repetitive dives. Also, breathing gas diluted with helium may be used to reduce the effects of nitrogen narcosis during deeper dives.
Diver rescue, usually following an accident, is the process of avoiding or limiting further exposure to diving hazards and bringing a diver to a place of safety. A safe place generally means a place where the diver cannot drown, such as a boat or dry land, where first aid can be administered and from which professional medical treatment can be sought. In the context of surface supplied diving, the place of safety for a diver with a decompression obligation is often the diving bell.
In scuba diving, the rule of thirds is a rule of thumb used by divers to plan dives so they have enough breathing gas remaining in their diving cylinder at the end of the dive to be able to complete the dive safely. This rule generally only applies to diving in overhead environments, such as caves and wrecks, where a direct ascent to the surface is impossible and the divers must return the way they came.
Diving equipment, or underwater diving equipment, is equipment used by underwater divers to make diving activities possible, easier, safer and/or more comfortable. This may be equipment primarily intended for this purpose, or equipment intended for other purposes which is found to be suitable for diving use.
Dive planning is the process of planning an underwater diving operation. The purpose of dive planning is to increase the probability that a dive will be completed safely and the goals achieved. Some form of planning is done for most underwater dives, but the complexity and detail considered may vary enormously.
Scuba gas management is the aspect of scuba diving which includes the gas planning, blending, filling, analysing, marking, storage, and transportation of gas cylinders for a dive, the monitoring and switching of breathing gases during a dive, efficient and correct use of the gas, and the provision of emergency gas to another member of the dive team. The primary aim is to ensure that everyone has enough to breathe of a gas suitable for the current depth at all times, and is aware of the gas mixture in use and its effect on decompression obligations, nitrogen narcosis, and oxygen toxicity risk. Some of these functions may be delegated to others, such as the filling of cylinders, or transportation to the dive site, but others are the direct responsibility of the diver using the gas.
The following outline is provided as an overview of and topical guide to underwater diving:
Diving procedures are standardised methods of doing things that are commonly useful while diving that are known to work effectively and acceptably safely. Due to the inherent risks of the environment and the necessity to operate the equipment correctly, both under normal conditions and during incidents where failure to respond appropriately and quickly can have fatal consequences, a set of standard procedures are used in preparation of the equipment, preparation to dive, during the dive if all goes according to plan, after the dive, and in the event of a reasonably foreseeable contingency. Standard procedures are not necessarily the only courses of action that produce a satisfactory outcome, but they are generally those procedures that experiment and experience show to work well and reliably in response to given circumstances. All formal diver training is based on the learning of standard skills and procedures, and in many cases the over-learning of the skills until the procedures can be performed without hesitation even when distracting circumstances exist. Where reasonably practicable, checklists may be used to ensure that preparatory and maintenance procedures are carried out in the correct sequence and that no steps are inadvertently omitted.
Recreational scuba certification levels are the levels of skill represented by recreational scuba certification. Each certification level is associated with a specific training standard published by the certification agency, and a training programme associated with the standard., though in some cases recognition of prior learning can apply. These levels of skill can be categorised in several ways:
A diving emergency or underwater diving emergency is an emergency that involves an underwater diver. The nature of an emergency requires action to be taken to prevent or avoid death, injury, or serious damage to property or the environment. In the case of diving emergencies, the risk is generally of death or injury to the diver, while diving or in the water before or after diving.
{{cite web}}
: CS1 maint: bot: original URL status unknown (link){{cite web}}
: CS1 maint: unfit URL (link)